HP Color LaserJet M277n MFP: HP Color LaserJet MFP M277n CONNECTED to THE NETWORK, SHOWS NO INTERNET CONNECTION

Similar Questions

• HP LaserJet M1522nf begins to lose the network connection

  Hello! I have HP LaserJet M1522nf and I use it for about 1 year maybe, but since last week, he begins to lose the network connection (ping failed, web interface does not work too). To be correct, the printer is connected directly to the network through an ethernet cable, and the cable is perfectly fine. His work when you turn it on and for the next 5 to 15 minutes, but after that it lost connection (tasks start fails).

  I really like using little aid, some perhaps of advice. Any suggestions?

  Hard reset the router to factory settings and reconfigure your settings.  Pass the cable to a different port on the router.  You said that the cable was good... change anyway.  Try now.

• HP LaserJet 200 M276nw: Configuration of the network for HP LaserJet 200 color MFP M276nw

  Can the M276nw of 200 HP LaserJet can be configured to scan to a network without initial setup of a PC folder? Without having first to connect the unit to a computer first.

  We run a virtual environment and the printer will need to scan to a folder configured network and this should be done through the device. Of course, file permisisons will be completed before. I think I saw a manual where the Embeded webserver had this configuration, but would have to make sure, before committing to the purchase. Thanks in advance.

  We gladly invite you.

  Yes, the printer supports the SMB Protocol indeed.

• LaserJet M3035xs MFP Scan because of the network folder

  Hello. I had a question about the scan to network folder option on our M3035. At the same time, I had this put option in place and works very well with all our Windows 7 computers. The hard drive in the Copier has failed and had to be replaced that erased all our settings. I used the wizard to add folders to the copier to scan network and even though files test ok at installing any of my test scans are appearing in the record. I was getting an error in a first time on it is not unable to check access I went into the settings using the IP address and added my credentials in this way. After this step, I was able to scan, but nothing appears in the record. HP wants $1,000 to get out because we are no longer under warranty.  Any assistance that you can offer is greatly appreciated!

  Sharon

  Thank you for responding. My Info was valid and set up the same way it was before. I decided to take a different route and put all the files on the server through the server to scan and save. That seems to work for now.

• HP LaserJet MP604: HP LaserJet MP604 do not print the PCL NET files

  Hello.

  New HP LaserJet MP604 printer does not display files PCL through a network, sent directly from PC.

  It print file correctly to the Web Interface (upoload PCL file https://10.17.200.112/hp/device/Print/Index), , but not network.

  I don't have these problems with the previous model HP LaserJet M602, it print properly the network file.

  Also when I print from MS Word, I see, what format of file (from to C:\Windows\System32\spool\PRINTERS printer spool) changes SPL, before (for printer M602 files are plain text with PJL and PCL commands), but for printer files as zip/xml MP604.

  What can I do to change the settings for HP LaserJet MP604 so that he began to support PCL printing directly from the net?

  And what I have to change to see PCL/PJL commands coil?

  >>... If the file contains only plain ASCII text nothing prints and no error message...

  So maybe the definition of the '\\msk-ent01.ru.ori.local\intop1lj' target is incorrect?

  I remember vaguely when using "copy" at a command prompt session Windows, the target must be a Windows share name, preferably the one corresponding to the final part of the name of 8 characters or less.

• HP Color Laserjet M277n MFP: How to use the black cartridges only when the color toners are empty

  Hello team HP,

  I recently bought a HP Color Laserjet MFP M277n I printer I print black & white user only and really don't need color prints. How to set the printer options to print only black & white? How can I replace only the black cartridge when the color cartridges are empty? How many prints (approximate), we can take by toner?

  Kind regards

  Christèle

  Hi @Pavumba,

  Welcome to the Forums of HP Support!

  I understand you're wondering how to use black ink only on your HP Color Laserjet M277n MFP printer. I would be glad to help and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I see that you wonder if you need to replace the color cartridge when it is low. This printer is a printer AIO, therefore, you need to replace the ink cartridge when it becomes too weak to be able to resume printing. However, if you print mostly in black, you can configure a preset black only to print in black and white. This would help reduce the use of the color cartridges.

  NOTE: Composite black - for black and white images and photos, a mix of colors called 'composite black' can be used to achieve the quality significantly improved picture and soft gray tones that can be achieved with only black toner. For users who want to print images using just black toner, many HP printers color customer offer configurable options allowing the client to print using only black toner. For example, by selecting "print in grayscale" in the printer driver Specifies print using black ink only. For more information about the use of the toner cartridges, please see this article: how the Toner is used.

   

• HP Color LaserJet Pro M177 MFP: HP Color LaserJet Pro MFP M177 cannot find information network

  I just got my new printer today. I followed the instructions to the letter. Now I try to connect to my network to the "Wireless Setup Wizard" that my router does not support WPS. I sat waiting for the printer view all networks in the range so I could choose mine and continue on. However, after 15 minutes of waiting, I decided to go shopping while he did his thing. I came back 1 hour later and it's still displaying "Retrieve information from wireless network" with the symbol of HP and a blue bar encircling it. It is not locked up as I can hit the Cancel button and it returnes to the network configuration menu. What I'm doing wrong here? My network uses a router NETGEAR WNDR4500 with security WPA2-PSK [AES] is enabled. It transmits the band b/g 2.4 Ghz and 5 Ghz n band. Please any help would be appreciated.

  Hi @Rieu,

  Welcome to the HP Forums!

  I see that your HP Color LaserJet MFP M177 Pro cannot find the network on Windows 7. I'm happy to help you with this problem of connection!

  Please, take a look through the steps in this guide, "Printer is off-line" Message appears on the computer and the HP printer does not print. Thus, this guide, the printer is not maintaining the wireless connection.

  Tips for troubleshooting wireless problems

   

• Color Laserjet PRO MFPF 377dw: problem with Color Laserjet PRO MFPF 377dw and HP network scanner

  After removing the package of printer drivers HP, all attempts of resettlement via WLAN regularly fail before the end, which indicates that the device is not found. I physically connect the printer to the computer by USB cable to install the software successfully. When I go to WLAN Wireless thereafter, the printer works perfectly within the network. If I remove the USB cable, the following error message appears when I try to start scanning HP: HP CLJM377 Scan found . In other words, HP Scan cannot be used with a PC not connected by USB cable. All other remote features function normally printer in wireless, including HP Scan & Capture. Is there a possibility to correct this, via the Windows registry from my PC?

  MrRobot wrote:
  

  Hello! @Chirsistei, your description of the HP product is classified as a commercial product (business). Our sales support team provides support via the channel of entry here. If you need immediate assistance, you will need to open a session one business with our sales support team. Click on this link http://ow.ly/I3gw30140F8 for more details.
  Let me know if you want more information and/or assistance.

  Have a great day!

  See you soon!

  Hello Chetan,

  I think I'm in the wrong forum here because I live in Switzerland and here the Laserjet Pro M377dw color is sold to private users. I have no access to a support plan and use the printer in my home office network. Your proposed solution therefore does not help me, during this time, I have posted this problem in the forum on language German you need not to pursue this new. Thanks anyway

• HP Color LaserJet CP1525nw: Can't get CP1525nw connected to the network wireless Netgear Nighthawk x 6 R8000

  I have never been able to successfully get the printer installed by wi - fi with any stability, so we always connected via USB and shared. I bought a new router and would like to be able to print to this printer wireless anywhere on my network. I can't out of connected mode and mode wi - fi printer. Your software crashes, crash facilities to half way through. The printer indicates an IP 169.254.xxx.xxx, if the network is aware, but it's I can get. None of the HP tools will run under this operating system, they hang immediately upon launch. It's frustration none! Someone out there was a bit of luck with this printer!

  Dell XPS 8700 16 GB of RAM

  Earn 8.1 (64-bit)

  Comcast TG862G Gateway (POS)

  Router wireless Netgear Nighthawk x 6 R8000

  HP LaserJet CP1525nw color printer range

  Hi @jrmunn ,

  I want to help you get the printer works on the wireless network.

  There are a few different ways to install the printer on the wireless network.

  • Thanks to the support WPS.
  • Through the installation, by connecting the USB port, it will configure the wireless.
  • Once the USB installation is done. You can configure the wireless via an Ethernet connection.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Uninstall the printer software.

  WPS configuration method:

  To connect your printer to your wireless router wireless using WPS:
  (your router must support WPS)

  Start the mode of the WPS button on your printer.
  Within 2 minutes, press the WPS button on your router.

  Then run a printer from devices and printers Add Wizard.

  The USB method:

  Perform a clean boot on the computer and disable the Antivirus software and any analysis in real-time in the Antivirus software also. How to perform a clean boot in Windows.

  Then run the installation immediately after connecting the USB cable, follow the steps described in this document to update the drivers so that's not new error. A fatal error during Installation of the software. Then the installation should continue. (you can use this procedure for any type of installation)

  If you are still having problems and you have an Ethernet cable, we can install the printer as a USB connection again and then configure the printer via wireless Ethernet.

  Method of Ethernet:

  Restore the default settings of the printer.

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Print a printer configuration page, to get the new IPv4 address.

  Then create a new port with the new IPv4 address.

  In the devices window and printers, click right on the printer and on the left, click on printer properties, select the Ports tab.

  Click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.

• Color LaserJet CP1025nw, unable to change the print density

  Hello

  I need to raise the "print density" 5 (for pcb toner transfer) on my Laserjet
  Color CP1025nw, but when I open the properties of the printer I don't have this option
  on the device settings tab, despite what is said on the page using this model.

  OS: Windows XP
  The printer is on the USB port.
  The driver is: HP LaserJet Professional Series CP1020 + update

  How can I change this setting?

  Help, please!
  Thank you in advance for any help you can make!

  All the best,

  Hi Spencer,.

  Fine forecast here too, but only 65 F, which is above normal for this time of year.

  I finally installed a wireless router to access the printer and BINGO!, all the density settings are

  available via the integrated Web server.

  Thank you again so much for the advice for beginners I

  All the best,

  Benoit

• Bought HP Laserjet Pro 200 color printer & unable to connect

  Bought HP Laserjet Pro 200 color printer & unable to connect to my Windows 7 laptop. The printer setup was a snap, but no connection. Tried all Windows resources, but...

  Most often when a device does not work, it's because the driver has been corrupted.

  Try reinstalling your.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• LaserJet Pro M127fn - failed to get on the network MFP

  I'm the wired network, but config report shows the ip address is 0.0.0.0. With the help of Windows 10. What ip address to use?

  Hi @kckeene117,

  I see that you are having problems, install the printer on a wired network. I will definitely do my best to help you.

  When the ethernet cable is connected to the printer and the router, the router is supposed to send an IP address to the printer automatically. (192.168...)

  Power cycle the router and restart the computer and the printer. You may need to try a different port on the router or another ethernet cable if you have not found an IP address. Check the connections at the back of the printer.

  Do you have Mac filtering on the router?

  What type of network setup you have and what is the brand name? (modem/router, router, switch)

  Check if you have a valid IP address.

  Here is a document to set up the printer on the network.

  Configure the printer to a wireless or wired network for the HP LaserJet Pro MFP M125, M126, M127, Color LaserJet MFP M176 Pro and and M177 Printer series.

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If you have any questions, please let me know what steps you have taken and the results. Thank you.

• Can I make a search on the network with HP Laserjet M1132 MFP that is connected to another computer?

  I can't seem to be able to scan with HP Laserjet M1132 MFP on the network (printing works fine). Is it possible, and I just don't know / are unable to connect or it doesn't have this feature?

  * Everything works fine on the computer that is connected to the multifunction printer over USB cable

  Hi Deividas,

  I can't wait to hear that you have questions.  For the LJ 1130 base series networking is not supported, however for some 1132 models Ethernet network is supported.  It will depend on the exact product/model number for this unit.  Click here to find out how to set up a wired network for 1132 connection the selection of models that supported this option.

  1A configuration of network peer-to-peer sharing of the computer that is connected by USB?

  2. What is the number of product to the rear of the unit, should start with J?

  3. how you analyze (front panel, scanning software, etc.)?

  Let me know and we can go from there.

  Kind regards

• HP Laserjet M1132 MFP is too slow on the network!

  Hello

  My HP Laserjet M1132 MFP is too slow on the network!

  I connect the printer to the windows XP 32 bits SP3 using UBS port. The printer works fine on the local computer, but when he shared on the network running too slow, for example with the print test page it takes about 45 seconds to print and other documents, it takes much longer.

  I installed the last form HP driver site and update the firmware it the latest version.

  It happens on other Windows XP machines as well.

  I have connected the printer to my laptop (Windows 7 64-bit) and it works very well (no delay on the network) and it seems that this problem have some relationship with the windows XP Driver.

  I used the trick of local port on computers remote (instead of the normal method) like this:

  "add a local printer.
  "new port".
  "localport".
  \\XPcomputer\HPPrinterName port name

  but still nothing!

  There is nothing wrong with the network, allows us to use a Samsung printer on the same machines on the network without problem.

  I really appreciate your HELP!

  It seems that no one on the planet has the answer to this question!

  The only available option is to upgrade your operating system to windows 7 (vista can work, I have no idea!).

  He wat the only solution for me.

• MFP HP LaserJet Pro M126nw: Clarification of the use of HP Laser Jet MFP M126 nw Pro Page

  Hi support them.

  Recently, we bought a new HP Laserhet MFO M126nw Pro. The cartridge came with the new printer. I need a clarification of the HP Laserjet Pro MFP M126nw on the usage Page.

  We want to know how many pages that the printer has taken so far, printing and also how many pages is analysed and the copier took how many pages.

  I have attached the report using page for your reference.

  Please specify the things below.

  Pages for the scanned copy = 65

  I think he has counted only scanned copies 65.le is okay?

  2. What is Monochrome pages printed from copy = 66

  3. What is pages scanned host = 86

  4. print engine:

  1. total Impressions showing 829.

  Overall, I think it's showing printing, copier, 580 the scanned pages. Is this OK.

  2. What is jam events?

  It's showing 1.

  3. What is EconoMode Impressions?

  showing 0.

  4. What is monochrome prints?

  showing that 829

  Need to clarify the details above for my knowledge.

  Your support is much appreciated.

  Thanks in advance

  Concerning

  R.Pradeep

  the digital and print values are different.

  pages scanned copy 65 - this means that 65 pages have been executed by the scanner with someone using the copy function. the report shows 66 printed pages 'copy' which means 64 of these copies were only a single copy and 1 scan someone made 2 copies - which gives you a total of 66 pages printed from the copy function.

  pages scanned to accommodate 86 = that means 86 pages were executed by the scanner with a person who uses the "scan to network folder" or "scan to computer" function

  That's a total of total of 151 pages run through your scanner. only 2 values that you add to the scanner are the "copy" and «scan to host» numbers copy of 65 + 86 scan-to-host ='s 151 total scans

  total impressions are 829. pages printed from copy fuction are 66 - if you subtract 66 829 that gives you the number of pages that have been printed from a computer = 763

  763 pages printed computer + 66 pages printed using the copy function = 829 total number of pages printed