HP Color Laserjet Pro M252dw: Cannot print from Gimp or Adobe Photoshop

Similar Questions

• MFP M277dw: M277dw LaserJet Pro MFP - cannot print from word, PowerPoint and excel

  Hello

  I just bought a Pro M277dw MFP LaserJet

  It can not print a word a simple page, PowerPoint, and excel.

  No error message with word.

  is the printer online for PowerPoint.  (when I just did a test of the printer page)

  In excel it says maybe NOT enough avaiable memory...

  I find that very strange that it only 1 page and nothing else is running.

  Please review this issue as soon as POSSIBLE.

  Thank you

  Dear Liquid083,

  Well done.

  Thanks for leading me in the right direction

  This "Universal Post Script driver" has worked for my word, PowerPoint and excel

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=4157320&swLangOid=8&swEnvOid=4132

  For others who are facing the same problems, please click the link above.

  Then look at what follows.

  HP for Windows PostScript (64-bit) universal print driver 6.0.0.18849
  11 December 2014 19.3

  Thank you

• Color Laserjet pro m252dw: print off center

  My printer prints slightly biased (as too far to the right). I did the alignment test and tried to solve the problem by adjusting printing to several mm to the left, but it does not work. I am trying to print labels with graphics that contain a border of circle-because the page is printing off center seem no good labels. I print on sticker paper for labels and have used several different programs label to print from, and all have the same resulf of centred off the coast. Any suggestions? Help would be very appreciated!

  Hey @OldSoulA,

  Welcome to the Forums of HP Support!

  I understand that you have a problem of quality when printing labels from your computer Windows 8.1 to your HP Color LaserJet Pro M252dw. I would like to help you today with this problem of printing the label. Thank you for all the troubleshooting steps you tried before reaching out for support. At this point, I'm going to make sure that the labels that you are printing on conform to the specifications of your HP Laserjet Printer. Once you confirm that the labels you are using are supported, we will miss some tests in order to check if this central issue is caused by the type of paper or a problem of setting. Please follow the steps below.

  Step 1: Check paper:

  According to the specifications of your HP Laserjet Printer, the following labels are supported:

  

  • You can load up to 50 sheets of labels into the tray at 1 time. Do not exceed 50 sheets
  • Avoid mixing media into the tray with paper. Avoid labels on top of plain white paper in your loading tray
  • Avoid using labels that are separated from the backing sheet, wrinkled or damaged in any way
  • Do not use labels that have exposed the carrier sheet
  • Do power not more than once a sheet of labels into the printer
  • Avoid printing on both sides of the labels
  • Avoid printing on sheets which the labels have been removed
  • Make sure that you use the specific Laser as adhesive labels can damage internal components in your machine.

  Once you have confirmed that the paper of the label that you are using is meet the specifications of your printer can you please move to the next step.

  Step 2: Print Self Test:

  1. Load of the plain white paper in your paper tray
  2. On the front panel of your printer then drag your finger to the left and select configuration
  3. Under the menu Setup touch Service
  4. Tap the cleaning Page
  5. Print a cleaning Page now. This page should show the colored lines centered

  Check the alignment of the present report.

  • The colored lines appear centered?
  • Printing documents from your computer on plain white paper print centered?

  Please reply to this message with the result of your troubleshooting so far. Once I have the results of your troubleshooting with the answers to my questions above, I'll be more than happy to provide additional assistance for this problem. I look forward to hear from you!

• color laserjet pro m252dw: How do to return/difficulty recent update of firmware for hp color laserjet pro m252dw as now does not

  My printer color laserjet (color laserjet pro m252dw) no longer works due to not recognize a black cartridge to third because of a recent update of the firmware. Error given is 'Supply memory error'.

  I already looked to the top of the page of Software Support for this printer, but new and recent firmware update is not released/listed, only the firmware upgrade market is given.

  I'd appreciate advice and instructions on how to return/repair my printer no longer print.

  Can you please advise on which firmware update to install instead to get my printer back in the order of operation?

  Thank you very much

  Geertje

  PS: HP: how VERY boring; next time that I'm in the market for a printer I have will conduct the review of my options

  According to the other thread that I have commented on the user managed to solve the problem of roll back firmware version 20160331 to 20150716 .  Unfortunetly the user did not comment if the old version of firmware is out so that we can share a simlilar solution.  It may be that this person had a copy archived in offline mode or found another source outside the HP support Web site.

  At least you can get an older version of firmware all the steps that we share for the firmware downgrade won't do you no good.  I'd be careful to search a German site for firmware updates.  HP has put regional locks in place according to international contracts, that they do to market their products in a given region.  Using a German firmware on a printer WE made may have strange side effects on what types of cartridges are allowed.

  What is perhaps a better use of your time would be to contact your 3rd party cartridge company and see if they can send you a cartridge that is compatible with the new firmware.  Chances are that they have seen the same problem with other users and already have a chipset to work around the problem.  In this way, you can stay on the newest firmware and continue to use your favorite too cartridges.

• HP Color LaserJet Pro M252dw: HP Color LaserJet Pro M252dw

  I print an A5 booklet using folded A4 paper. How can I stop printing page doube to print one side upside down. I can solve this problem by setting the print upside-down page, it prints the right way around... but if the printer should be able to make the impression of the way round on his own?

  Hi chazzzz,

  Welcome to the HP Support forum.

  I understand that you use a HP Color LaserJet Pro M252dw with a Mac OS X 10.11 El Capitan and when you try to create an A5 booklet using A4 size paper folded one side of the paper is printed in reverse. I would like to help.

  The printer can print double-sided and have two sides printed the right way around. Looks like you might be not to select the appropriate link option.

  

  Follow these steps to use the auto duplexer built-in for most printing.

  

  Please let me know if that solves the problem, or if you need assistance.

   

• My HP Officejet Pro 8600 cannot print from my MacBook Air

  Hello

  My HP Officejet Pro 8600 cannot print from my MacBook Air. It keeps on showing "the printer is not connected", but the display on the printer connected. I often reset the printer "EVERY TIME" I want to use. I also tried to turn off my laptop and printer several times before printing. If I'm lucky, it will work maybe for one or two prints. If no luck then I have to reset everything again. Sometimes I reset the printer, the printer is not displayed on my selection.

  Hello boojoo1tw,

  Welcome to the HP Forums!

  I understand that you are unable to print most of the time with your Officejet 8600. How is the printer connected? USB or wireless? What is your operating system on your Mac computer? Click here to find out.

  If your wireless printer, then I recommend the award of an 'IP address' by following this HP document on printer does not maintain the wireless connection.

  Please post your results, I'll be looking forward to hear from you.

• M251nw color LaserJet pro 200: does print in black only, no color

  All of a sudden, my m251nw color laserjet pro 200 prints only black. Cartridges changed (C/M/Y) without modification. Toolbox shows that they are all 100%, but nothing will be printed in color, not even the Demo Page. Anyone able to help?

  Updated the firmware from hp, and it fixed the problem.

• HP Color LaserJet Pro M252dw P: M252 priority feed slot paper

  Hello

  So, I have the HP M252dw to work. I can't insert sheet simple slot (Tray 1) feeding into the printer. Can someone help me or give me specific instructions?

  Thank you.

  Hi @trans30and welcome to the Forums of HP!

  I see that you are looking by reinstalling the paper tray. I'd like to help!

  I'm including a document below, and in this document, you will find that a section marked "the feeder loading":

  HP Color LaserJet Pro M252, M274, printers M277 - establishment of the printer hardware

  That should guide you install the tray, with pictures to help the process.

  Good luck and please let me know the results of your troubleshooting operations. If this solves the problem, click on accept the Solution below, as well as others to find the answer. Thanks for posting on the HP Forums!

• Cannot print from MSOffice or Adobe Reader on HP Officejet 4620

  Cannot print to MSOffice or Adobe Reader for HP Officejet 4620, but I can print from the internet, and I can print emails.  My ink level is full, and it prints well on the internet, so, apparently, that my printer working.  What can cause problems printing only from computer programs?

  Additional info: when I hit print paper out, but most of the time does nothing about it, but sometimes a fraction of the page prints even if the setting is to print the entire document.

  Any suggestions would be greatly appreciated.  Thank you.

  Hello Debbeedue,

  Welcome to the HP Forums.

  I see that you have a problem with printing of MSOffice and Adobe Reader.

  Please click on the following link and run HP Print and Scan doctor.

  If the doctor gives error codes, please make a note of the error codes and let me know, if you please, what they are.

  Thanks for your time.

• HP Color LaserJet M553: M553 - cannot print two-sided

  Hello

  We have a new HP Color Laserjet M553 (B5L24A) which is not allowing us to automatic duplex.  He is currently runinng via a Windows 2008 R2 server and is network connected via IP static on the Ethernet cable.

  I tried several steps of troubleshooting so far:

  -Several including UPD PS 6.0 5.8 PS, PS 5.5, PCL5 printer driver

  -Several print on print server objects

  -Confirmed the 'device settings tab' has the duplexer enabled on the local print server and print objects

  -Updated firmware for the last datecode 20150731

  -Tested printing from several applications, word, outlook, pdf, internet Explorer, textfile, etc...

  -The same problem happening to all connected users

  The printer accepts orders for manual, automatic duplex printing simply cannot.  No error messages didn't report on Panel print, printer, client or server.  Trying to get your hands on a 2nd M553 so that I can confirm a double problem or not.

  Feels like a problem with the firmware where he does not understand the command duplexing automatic normal or did not recognize the duplexer is installed.

  Any ideas?

  Your model is not the two-sided model.  The duplex model is B5L25A and will say about this M553dn not M553n who is your model.

• HP officejet pro 8600 - cannot print from my macbook pro

  We just bought a new HP officejet pro 8600 but for some reason, we cannot get my macbook pro to print on it. My mac says it is connected to it. It is listed in the printer only and all the settings look fine, but when I send a document to the printer, it will not be printed. He did print the first day we had (a week ago) but it stopped and we cannot figure out what to do. My daughter's PC will be printed, as well as the pc of my husband. It is the first time that I had problems printing to a hp from my mac. Any thoughts?

  I had my Officejet Pro 8600 about six months.  Recently, I had the same problem.  It continues to print from my Windows computers but not the Mac.   Labour goes into the impression that it is place on a wedge.  I tried many fixes, including the removal of the printer and reinstall.  Usually removing and reinstalling it will fix for a while, but now, even that does not work.  In my view, that the permanent solution is to buy another printer.

• Color LaserJet Pro CM1415fnw multifunction - print that hangs or restarts printer after the print request

  I am using a LaserJet Pro CM1415fnw with a wireless connection and a USB connection, for several years with my MacBook Pro, spanning several evolutions of the Mac OSX (Mountain Lion, Lion, Mavericks) without incident.

  Today, no reason apparent, the printer started to expose the problems of processing printing orders sent, through the wireless and via the USB port.

  When you try a wireless connection, the print queue to fill up and the LCD will display printing in progress (with no impression caused), then the screen would just whiten and the printer would appear to restart, with the HP logo, and then subsequently return to the normal display mode, as if she was ready to print or copy, no matter.   No printing would take place, and the print queue would remain as if there is a current print job, with no impression caused.

  When you try to use the USB connection, the print queue indicates that a print command has been sent to the printer, but then, he did the same wireless, with the LCD screen goes white and apparently to restart the printer.  The print queue is populated, but printing never takes place.

  I have reset the printing system several times, removed and reinstalled the printer several times (wireless W USB connections), use the HP utility to try to install the printer, download and install the latest version of the driver for the device, rebooted the MacBook Pro, etc, etc.

  The ONLY thing that can print at this time is if I use the HP utility software, and receive information from device and then use the PAGE printing CONFIGURATION - then and then only, the printer responds immediately and prints the page, just as it was always in the past (until now!).

  I have tried everything I can think, for several hours, and can not understand what the problem might be.

  Any idea to solve this problem would be greatly appreciated!

  Norman,

  Thank you for your constant perseverance on this issue.  I forgot my post here, until I received a notification today about your response to date.

  Curiously, I "stumbled" upon the cause of the problem recently, and he had NOTHING to do with the printer or the MacBook Pro OS X (recently updated to Yosemite).

  It turns out that the problem was in the PDF file that I was trying to print!  Periodically, I'll print PDFs to a particular Web site, and it is these PDF files - exclusively - who made the mistake of communication between the computer and the printer.  The problem with PDFs is unique to the Mac OS X, because I can print the exact same PDF files from my laptop running Windows without problem.

  I have no idea what the "Bug" in the East of PDF files... probably never is, but given that I can do what I need to do with a Windows laptop, my problem is solved.

  I contacted the Admin on the website where I was printing the PDF files they offer, to make them aware of the situation.

  Thank you for your interest and your help!

  Dave

• HP LaserJet Pro 400 m401dne: print from Notepad

  Hello! I have a new HP LaserJet Pro 400 m401dne. Everything works fine except when I try to print both sides of a Notepad document copies. As soon as I select the duplex option, the entire document disappears. We had an another HP LaserJet only printed on one side of the paper; who would have something to do with it? Still, I have this printer on the printer list but am selecting a new. I can print any other documents on 2 sides; just don't leave the notebook. Thanks for any help you can give me!

  Thank you, HP! The warranty issue has been resolved and so was the two-sided printing problem. The technician had to install Universal printing and now I can print copies front and back of notebook and everywhere else.  )

• LaserJet Pro M402n: Cannot print on LaserJet Pro M402n on port TCP/IP for Windows 10

  I'll put up a new workstation Windows 10. It is brand new with all updates applied. The printer gives me fits. I tried to install as myself (with administrator privileges), 'run as administrator' and logged in as a local administrator and I got the same results each time. I used 'install' and 'non-installateur' version of the most recent drivers.

  The printer is a HP LaserJet Pro M402n. I'm installing a Standard TCP/IP Port. I can ping the printer. I can get on the printers web interface. Likewise, the installation program detects the printer and gives no error. But when the installation is complete, and I try to print a test page, nothing happens.

  The same printer is configured the same on my old Windows 7 workstation which is still on my desktop and connected by the same switch and on the same subnet as the new work center. It prints very well.

  Any ideas to get this to work?

  Got, it works. It had to be that something gimped upward in the initial installation of Windows. I've reconfigured on the PC and was able to get the printer to work first time.

• M176n MFP: HP Color LaserJet Pro M176n MFP - print in reverse order

  All my print jobs print in reverse order. So if I have a great doc to print, the last page is on top. I don't find in the settings of the printer where can I change the order of the prints.

  Help, please

  Hi introvert,

  Thanks for responding. But I think I lost you somewhere.

  I downloaded the driver to the place where you sent me. No problem. I unzipped. Then I went into the temporary folder, but everything I've seen has this folder:

  HP Support frame

  So, I opened this file and only found this:

  HPSF_Config1.dll

  I went through the motions and copied the address of the place and done what you told me:

  -----------------------------------------------------

  • In the devices folder and printers, click with the right button on your LaserJet Pro MFP M176n and left click on printer properties
  • Left click on the Advanced tab
  • Left-click on new driver
  • When the new window driver opens just hit 'next' until you see a list of manufacturers on the left and a list of printers on the right.
  • Click the "disk" button at the bottom right
  • When the "Browse" window opens, simply right click in the path of the file bar and select "Paste" to paste the path of the file that we copied earlier. Click OK.
  • -------------------------------------------------

  When I pressed "OK", it says "file contains no software driver for your currency. Select a folder that contains the driver software, and then try again.

  He never did a 7z file in the temp. folder...

  So what I am doing wrong? Again, help please! Thank you!!!