HP Compaq Presario CQ61 - battery - new battery (icon shows 100% available, connected load)

I replaced my laptop battery and the icon shows now available at 100% but connected load.

Remove the cable from the laptop dies immediately.

Have I done anything measured during the installation of the battery?

Can you please check if your AC/adapter works normal by connecting to a different laptop

OR

Can you connect please an adapter of well-known power supply/AC of a different notebook with your laptop to check

So we can troubleshoot

Note: In case if you are unable to perform any of the actions mentioned above I highly recommend to immediately Contact HP Support by phone to get help without delay to get your Notebook diagnosed and repaired by an authorized HP Certified Engineer

You can also check your warranty here to check the status of the guarantee

Hope this helps, for other queries in response to the post and feel free to join us again

* Click on the star of CONGRATULATIONS on the left to say thank you *.

Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

Thank you

K N R K

I work on behalf of HP

Tags: Notebooks

Similar Questions

  • My Compaq Presario CQ61 battery.

    The battery on my laptop has been replaced when less than 12 months and now it shows again the problems.  Is this true, if I'm not very impressed by that.  My laptop is only 16 months old and will be on his 2nd battery!  Can anyone help?

    cotto1001 wrote:

    The battery on my laptop has been replaced when less than 12 months and now it shows again the problems.  Is this true, if I'm not very impressed by that.  My laptop is only 16 months old and will be on his 2nd battery!  Can anyone help?

    (1) have you calibrated your battery ever?  It was a must do from the beginning

    (2) using performance mode for a regime of power options?  Balanced is optimal and better for the longevity of the battery

    (3) don't you let your laptop connected to the power adapter, when it is not in use? When the load is low, plug, load it, and unplug it.

    If you do one or a combination of what I asked you, you have, perhaps inadvertently, shortened the life of your laptop battery.

    Most who do this just don't realize there are ways to treat a laptop battery, if you want to have the optimal way to battery life and ease of use.

    Best regards
    ERICO

  • Compaq Presario CQ61 - 421SA Notebook battery 484170-001 necessary

    I have a laptop Compaq Presario CQ61-421SA with a number of battery: 484170-001.  It gives a warning 601 at startup.  Even when I have the trendy area it will suddenly drain and stop immediately without warning making me lose whatever it is that I'm working on that day.  I am struggling to find a seller for a spare battery and what voltage can someone help me please

    Hello

    For example, the battery on the following link would be appropriate.

    http://www.Amazon.co.UK/replacement-CQ61-421SA-CQ61-421SG-CQ61-422SA-CQ61-422SG/DP/B009O5GVUU/ref=pd_cp_computers_0/280-1730758-8360619

    Kind regards

    DP - K

  • Compaq Presario CQ61: Need help with my Compaq Presario CQ61 after years of reflection, I had lost my files

    I HAVE a COMPAQ PRESARIO cq61 I died so I him I had sitting around the House for a while. I decided I had a lot of personal stuff on it just throw like family photos and videos. Then my mother ordered me a new battery & charger and the sound wahhlahh works again but its been like 4 years since I used it, and now I get a screen that says enter admin or the key to the power on password error its gave me is 87754760 please help if you can

    Hello

    Enter: 38632366

    Kind regards

    DP - K

  • Compaq Presario CQ61-420US no start/black screen

    Hi all.

    I have a compaq presario CQ61-420US having similar problems below, except I have a black screen, fan flashing lights turns is the same (num lock and cap lock) but they Flash continuously every second or 2.  I tried the hard reset with the fix of ram, connect an external monitor, change the battery and the power adapter, nothing helps. I also used the air compressed on the vents, just in case was riddled with dust because it overheats and can cause problems, but nothing.

    Any other suggestions?

    An option I can think of is to buy a new motherboard, but I'm going to try something else before that.

    AlexisGonzalezC,

    You can try the above solution the other person sugguested.

    Sorry, but it is very difficult to help without a touch your computer and troubleshoot it if there is a hardware problem.

    I predict that GPU your computer has a pseudo brazing or cold joint problem.

    Good luck.

  • Compaq Presario CQ61 problem

    Good day to all,

    I have a problem with my compaq presario cq61. My unit does not start with the battery or even the power supply is connected.

    > I don't know that my diet is in good condition. The LED is on and it's output voltage.

    > I noticed something that when I plugged the power in running the LED of the controller turns on but input domain after sometimes (about 5seconds) LED off suddenly.

    What is the problem with my Compaq Presario CQ61? Please help me with this.

    Thank you very much.

    Hello jervenbatilo,

    I see you have power relative to problems with your HP computer. You did most of the troubleshooting that is appropriate for your question.

    I'm including this link which has most of the troubleshooting steps that may solve your problem.

    If you are unable to get any power on the computer, it is most likely a problem with the motherboard of the computer.

  • Compaq presario CQ61: disable System

    Hello

    I got a message when I turn on the laptop, enter the password administrator or power on password? After 3 attempts it said system disable the key: 12503741

    (I tried to turn off the laptop and take out the battery and unplug the unit for an hour to see if it might reset it, I read thatit would be on another forum, but it did nothing)

    It is a compaq presario CQ61

    Thanks in advance

    @natalie110266

    Enter 03461387

    REO

    I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

  • Compaq presario cq61: change the boot sequence

    I have 10 Windows upgrade on my compaq Presario cq61 free. I want to do a clean install of Windows 10. I downloaded the tool of Microsoft Media, made a key USB and DVD containing the clean install. I am told that the use of the flash player, I have to change the boot sequence in the bios. I tried everything from ESC, all numbers F and LED to try to enter the bios and all have failed. Told me that all I had to do with the DVD was just put it in and start the computer and the laptop would boot from the DVD and I could make my own installation from there. Which also failed. The only thing I have not tried is downgrade to Windows 7, affecting Windows 7 back to factory settings, then reinstall the free update of Windows 10. I would not have to go through all if I mostly because I bought the laptop from a friend and it was installed at the factory of Windows 7 and I don't got no disc software to the computer so I don't want to screw up and drop windows 7 without the appropriate software reinstall to match the product key.

    Any help to enter in the bios or advice that could help me reach my goal would be greatly appreciated.

    Hello

    Here are some other suggestions.

    1. start the machine in Windows 10.

    Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

    In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, and then close any open windows and stop the laptop by right clicking on the icon from the Start Menu, then select prompt (Admin) and click 'Yes' to the uac prompt.

    Type (or copy and paste) the following command (including spaces) and click Enter.

    Shutdown /s /t 0

    Tap on the ESC key as soon as you turn it on and see if it will now access the Start Menu.

    2 try to connect a keyboard external usb and see if this will allow you to access the Start Menu.

    Kind regards

    DP - K

  • Compaq Presario CQ61-416SA: upgrade the Compaq CQ61 wireless card

    I have a Compaq Presario CQ61-416SA, running 64-bit Windows 7 application. The current wireless card only works on the 2.4 Ghz band and I want to upgrade to a dual band to get the best speed etc. to 5 GHz. I have an Intel Centrino N6230 of replacement card, but the phone will not accept anything other than the default map. At the start, it stops with an error message saying that it will not continue unless the "unauthorized device" is deleted. If I re - install the original wireless card, it starts and works very well, but this is not the point, I would like to update.

    I guess that the default is to lock the part of the BIOS of the laptop to prevent alteration unauthorized with laptop computers under warranty, but mine is well outside the guarantee.

    I know that the card works because I installed it in my laptop previous and I have been in electronics for 30 years and spent about 5 years of this repair of computers laptops, desktops, servers, etc so I'm sure that I am able to connect a card and the driver installation!

    There does anyone know a way around the block? I won't to be able to upgrade the laptop without it.

    Anyone?

    Do not completely blame HP, but it was little 1984 involving your federal Government. HP and Lenovo read a few Federal Communications Comm regs on the recording of radio portable wireless (including the computer wifi cards) to require that alternative cards are blocked. Other laptop makers has not agreed and now the 'white list' is history, but there is no effort to go back and make new BIOS for older models.

    HP wireless card versions have specific identification in the firmware looking for the HP whitelist before clearing the map to use if you use the version of HP. I looked pretty hard for a version of HP of the card and the one I linked is everything I could find. Google around and you can do better.

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • Compaq presario cq61: ssd in presario cq61 - 430ev

    I have a HP Compaq Presario CQ61.

    I just bought a Kingston HyperX Savage 240 GB ssd for my laptop, I had already upgraded to windows 10. The placement of the drive was a success, but during the 'clean' windows 10 installation asking the the disk drivers. I contacted the support service of Kingston, and they said this:

    "Please note that we do not really any specific drivers, the SSD would benefit from the planned system of system.
    Some systems may require a storage of pre-installation F6 driver, who usually provided by the manufacturer of the system in your case it would be HP.
    We recommend to check the following:
    -If it doesn't matter what Windows 10 associates BIOS update available for your system (make sure than his most recent available for your system)
    -Pre-installation F6 for your system storage driver (check the site of HP for these drivers).

    Then I updated my system to the latest version of the BIOS, but nothing has changed.

    I looked on the HP site, but I can't find any "storage of pre-installation F6 driver" or any other driver for ssd, so I can't install windows and use my laptop. What I would do about this problem? Help, please!

    Thank you very much!

    Hi @stepolis,

    Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

    I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your notebook Compaq Presario CQ61 and problems with a new install of Windows 10. I recommend to restore the default BIOS settings. You could restore the BIOS with this document by selecting the reload the default BIOS settings. In this way, it will look at the hardware installed on your laptop.

    Please let me know how it goes.

    Thank you.

  • Downgrade Compaq Presario CQ61-120EI from Vista to XP

    Please help me downgrade my new Compaq Presario CQ61-120EI from Vista to XP. What are the necessary drivers?

    Drivers:

    Intel chipset (Install and reboot before other drivers) here


    Intel Rapid Storage Technology here

    MS-UAA for SP2 (required with a reboot before the graphics and Audio, Modem driver) here

    MS-UAA for SP3 (required with a reboot before the graphics and Audio, Modem driver) here

    Intel graphics 4500MHD here

    IDT High-Definition Audio CODEC here

    High-Definition Audio (HDA) Modem Installer and driver here

    Synaptics Touchpad here 

    Atheros Wireless here

    or

    Broadcom wireless here

    Realtek usb 2.0 Card reader here

    Realtek RTL8102E Family PCI - E Fast Ethernet NIC Driver here

    .NET framework (required before HP Quick Lunch Buttons) here

    HP Quick Launch buttons here

    CyberLink YouCam software here

    If you had for 7 unknown devices (buttons drivers), here (new link)

    Do a manual installation

    Go to Device Manager, right click on the unknown device,

    Choose update driver, not to communicate.

    Choose the install from a list or a specific location, not search, have-disk,

    Navigate to the location of machine.inf.

    Do it for the rest of the unknown devices.

  • COMPAQ PRESARIO CQ61: Error ENTER PAST ADMINISTRATOR OR POWER ON PASSWORD password

    Recovery Bios Password COMPAQ PRESARIO CQ61 operating system: Microsoft Windows 10 (64 bit) Hello, I have a COMPAQ PRESARIO CQ61 and suddenly asks me the password of the bios. The message that appears is "ENTER password or POWER ON PASSWORD". What can I do? After failing 3 times I get the message "System disabled" and the code 59329588

    Please try-

    46081508

    Hope this helps, for other queries in response to the post and feel free to join us again

    * Click on the button white Thumbs Up on the right of say thank you*.

    Make it easier for others to find solutions by checking a response 'accept as Solution' if it solves your problem.

    Thank you

    GBL84

    I'm not an employee of HP

  • Compaq presario cq61: PROBLEM STARTING WITH PRESARIO CQ61... CAPS AND NUM LOCK FLASHES every 4 seconds!

    Hello! I have a problem with the starter. When I try to boot my laptop, my screen is black and Maj CapsLock and numlock just Flash every 4 seconds. Then I go to your page to download the BIOS. Well, when I dl and install Recovery BIOS for Compaq Presario CQ61-420EM get some InsydeFlash application, what is it for? I saw in the video that you get HP system BIOS update utility tool and that is the problem for me, I don't understand this application, instead, I get this "InsydeFlash" I don't know what is! HELP PLEASE!

    Hi @patrik13,

    Thank you for the update and confirmation.

    You would be kind enough to mark the post that solved your problem as accepted solution to help others who may have the same experience as you.

    Thanks in advance.

    Good luck with the repairs.

  • Compaq Presario CQ61-430SV: model of motherboard

    I have a Compaq Presario CQ61-430SV I would like to know the reference number of the motherboard has this laptop. Can someone help me?

    Map of discrete PM45 system for use with separate computer models, select (including integrated modem Digital Media Slot and replacement thermal material) 517838-001

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • Compaq Presario CQ61, unable to boot the laptop

    Compaq Presario CQ61 running Windows 7 Home Premium (build 7601) bought about 4 years ago.

    Computer failed to restart after a period of sleep.  I suspect that it doesn't have an automatic restart after automatic installation of an update - it's only a guess because I have no access to the computer at the moment, but I had a similar problem recently - on this occasion, I got a 'Safe Mode' start - by pressing F8 repeatedly gave me access to the appropriate screen.  I've implemented subsequently by restoring the system to a point just before a automatic installation of a critical Windows Update, and that seemed to do the trick.

    On this occasion the F8 route has no effect on the problem; the 'caps lock' and 'NumLock' continually of the blink just of LED (i.e. not a limited number of times), the fan starts, but there is no other sign of life.  I tried a hard restart, but without result.  I also removed and replaced memory, but once again no effect.

    Can you please advise.

    I'm so sorry I couldn't help you solve the problem, but maybe you could try to free the keyboard, nothing will happen if you do not lose the cpu and tight again. I know that the keyboard one is hard, persevering, best wishes.

Maybe you are looking for

  • announcement on installs without permission

    There is this addon that installs without permission. 'S called it funklyrics 1.122 it seems to be able to turn on even after being disabled. It seems the ride through an update. The program itself seems to be harmless but implements small adds tryin

  • MultiCam Twitter audio clip

    My audio finished on a multicam clip is Twitter and fluctuates during playback on a completed project.  How do I fix this?

  • WLAN is missing the MAC address and can not use WiFi

    After an important virus corrupt my system, I got everything running except internet Wifi access. The configfree detects the unit, Wireless 2200BG, which is enabled and the latest driver downloaded from Intel, but he said nothing to the MAC address.

  • Duration 8,5

    Hello I created a program and create an exe that, now I would like to open this program on a computer where there is no installed LabVIEW execution, the idea is to open the exe file so that it installs the runtime and then opens the program, is it po

  • Whenever I try to watch a movie on Netflix it says that an error has occurred.

    I recently got a MacBook Pro and I'm watching Netflix. Whenever I try to watch a movie, it says that an error has occurred. I contacted Netflix and they said it was a problem with brightness of light. How can I fid which. I also have trouble download