HP dc7600 sff

can someone please tell me if a XEON 3050 can be mounted on a HP DC7600 sff. BIOS has been updated with the latest firmware (Bios v 1.60). Thank you

Hello:

In a Word, no.

Here is the list of processors suppored when the latest firmware is applied.

Processor and speed *.
One of the following values
Processors Intel Celeron D:      
Processor Intel Celeron D 331 (2.66 GHz, 256K L2 cache, 533 MHz FSB)
X

Tags: HP Desktops

Similar Questions

  • Memory of dc7600 SFF

    Hello. This is what I am trying to accomplish. Got a renovated DC7600 SFF, equipped with a Pentium D 945 processor. He got 4 sticks of 512 MB installed between 4 banks (all PC2-5300). I would use 2 sticks in another pc running the same memory and replace my empty banks with 2 sticks of 1 GB each (PC2-5300), in order to have a total of 3 GB. It should work ok, I think, but I wanted to doublecheck. Any suggestions? Should I put the 1 GB sticks in 1 and 3 banks, or banks of 2 and 4?

    Hello:

    It does not matter.

    But most of the people would put the sticks of 1 GB but in banks 1 and 3.

    And Yes, it should work perfectly.

  • DC 7600 SFF: Upgrading of power on my HP DC7600 SFF

    Hi, I have a DC 7600 Small Form Factor desktop computer and it comes with a power supply of 240 watts. I want to put a x 16 PCI express graphics card and that is why I want to upgrade the PSU for probably a higher with about 400-450 watts. Can someone please guide me which would correspond to what kind of power supply in this case of machine as ATX, mATX, PS3, PS2, etc. SFX. Any help would be greatly appreciated. Thank you guys!

    You are the very welcome.

    I don't think that is correct.

    The main power connector to the motherboard in a standard atx P/S has 24 pins and I believe that if you check the main power connector to the motherboard on your dc7600, it has only 20 pins.

    I know that the card with 1 GB of only prints 29 w.  One with 2 GB of memory probably attracts a little more.

    You must be well with the 1 GB and maybe very well with the 2 GB.

    I like to use this calculator power supply useful for determining if a card that I want to install is a good choice for me without upgrading the P/S.

    http://www.extreme.outervision.com/psucalculatorlite.jsp

  • Compaq dc7600 sff keeps closing

    I have a problem with my sff compaq dc 7600 desktop top it keeps close & restart down. I can't put my finger on the problem because it is randomly .i have changed the ram & HDD & still the same thing happens I tested the temperature of the heatsink & apparently not warm all the fans are running. I did the test of memory (OK), I don't know if the bios may cause the problem? So any help would be welcome

    Jim Shepherd

    At any time, Jim.

    I am pleased to have been of assistance.

    Paul

  • HP 7600 sff: update bios dc7600, ver 1.61

    can anyone share a link that works for an update of the bios to version 1.61 to the dc7600 sff... Thank you...

    I don't understand.

    You have the files I zipped to the top and attached below (as attachments), correct?

    You have a formatted in FAT32 USB flash drive, correct?

    I just opened the folder with the files it contains and opened the flash drive to an empty window.

    Then I selected all files in the folder, right-click, "copy", then toss above the window open the flash drive and right click "Paste".

    Then, they just copied on my FlashDrive with no problems.

    If I had a dc7600 in front of me right now, I'd be ready to Flash the BIOS.

  • problems with ati radeon x 600 in dc7600

    Hi-
    Newbie here... I just installed a X 600/256 MB card pcie ATI Radeon in the HP dc7600 SFF and getting white 4-5 screen when starting with Windows XP.

    She also stopped twice in the past two weeks as the card has been installed. No problem with integrated graphics.

    My question is: I have loaded which, in my view, are the correct drivers from this site and the AMD/ATI site. Could someone please tell me / link me to drivers. Some do not list even the X 600 just X 550 / X 1050. No use gamming or heavy on this machine. ¿¿Would I better too just stick with the integrated graphics card?

    Thank you

    cpu201 wrote:

    Hi-
    Newbie here... I just installed a X 600/256 MB card pcie ATI Radeon in the HP dc7600 SFF and getting white 4-5 screen when starting with Windows XP.

    She also stopped twice in the past two weeks as the card has been installed. No problem with integrated graphics.

    My question is: I have loaded which, in my view, are the correct drivers from this site and the AMD/ATI site. Could someone please tell me / link me to drivers. Some do not list even the X 600 just X 550 / X 1050. No use gamming or heavy on this machine. ¿¿Would I better too just stick with the integrated graphics card?

    Thank you

    Hello

    I suggest to remove the card, reinstall the drivers for the integrated graphics card and using the onboard graphics for a week as a test.

    If the white screen start and stops disappear then you have found the culprit.

    If you do not need higher resolution graphics, you are definitely better with the embedded video solution. I suggest using the original drivers.

    What dc7600 do you have? (CMT, SFF, or ultra-Slim form factor are the three versions)

    Best regards

    ERICO

  • The dc7600 fan not slowed down speed

    I'm new here but I have no news for the repair of computers, a problem which therefore left me speechless!

    A customer brought me a Hp DC7600 SFF desktop computer and said that the thing is so loud it doen't want to use it.

    Card"Pentium 4 3.00 Ghz

    2 GB DDR2 533 memory

    320 GB HD

    Win 7

    I lit and was swept away, this thing is so strong that you does not think!

    I disconnected the chassis fan that he calmed down some but the CPU fan turns at 5400 RPM all the time, I can't get the fans to slow down! I tried to use the program Speedfan, it was a joke.

    I am at a loss for what to do and wondering if something on the Board that controls the speed of the fan go haywire. I also upgraded to the latest BIOS and that did nothing.

    When the computer starts, it seems frankly a small liquidation aircraft prepares for take-off!

    What to do, what to do? ANY suggestions would be most appreciated.

    Thank you for your comments/ideas and suggestions. I would recommend he get a newer system because I think it's history! We have done everything that we can and it's time to throw in the towel! Thank you so much!

  • Laptop Hard Drive 3.5 SATA hard disk (please fast response)

    I have a major problem. There is a HP Compaq DC7600 SFF on Ebay that ive been watching for a while. I have DDR2 RAM for her and a 60 GB laptop hard drive. Im going to be to put Windows Xp on the computer. The problem is to a SATA 3.5 hard drive. Is there an adapter for it? I'll need to get a new drive?

    Here is the link: http://www.ebay.com/itm/HP-DC7600-SFF-Pentium-4-HT-2-8Ghz-512Mb-No-HD-/271103764174?_trksid=p2047675.m1850&_trkparms=aid%3D222002%26algo%3DSIC.FIT%26ao%3D1%26asc%3D11%26meid%3D3652700529279890050%26pid%3D100011%26prg%3D1005%26rk%3D1%26sd%3D280958745061%26
    Help, please

    Hi Ryan,

    Thanks for posting in the Microsoft Community.

    I suggest using your favorite search engine and look for adapter that will allow you to do. You can also contact the manufacturer and check the availability of these adapters.

    Hope this information is helpful and let us know if you need help with Windows. We will be happy to help you.

  • video tearing watching the HD video

    Video problem

    I have a hp compaq dc7600 SFF with intel GMA 950, pentium 4 HT dual core 3.0GHZ and 2 GB ram and I'm pretty sure that this GPU is capable of up to 720 p videos, but even on lower quality videos video flies over and half top video is always a little ahead of the bottom in modes full screen

    first of all, I would reinstall the software driver and video film from the place of origin.  There may be a version update available with a fix.

    Secondly, I would then adjust the system by a check disk and Defrag.

    Thirdly, I temporarily disable all startups and services non-microsoft via a clean boot and also disconnect from the internet during playback of the video.

    If all goes well, trying all the above him video playback will be stable.   If Yes, then you can begin to try to understand of the above did the trick on your system.

    If this isn't the case, then you will probably get graphics performance improved via the pci of high-end graphics card.

  • My USB Ports suddenly stopped working

    Hello

    I connect a second hard drive on my desktop (hp dc7600 sff) and everything was going well until I was prompted to press F1 to save changes to new material. I realized my mouse and my keyboard are not 'read' via connected USB ports. I tried to change the ports but still nothing, so in the end, I was unable to choose the F1 for the recording of the new HARD drive. I tried all the other ports, but still, nothing.

    I am now faced with a dilemma, I can't go through the login screen because none of my input devices can be connected to the PC, as all modules are connected USB.

    Help. I need to return to my beloved PC usage.

    Hello

    According to the description, I understand that the USB ports do not work.

    I would like to know some information.

    1. Have you tried using the keyboard of the screen?

    Try to use your computer using the keyboard of the screen and check.

    http://Windows.Microsoft.com/en-us/Windows/type-without-keyboard#type-without-keyboard=Windows-7

    We can refer to the suggestions by Mohammed Raieed said on June 1, 2011 and check.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/why-did-my-USB-ports-stop-working-suddenly/11303612-0809-4A3B-a2ba-c0c6b1234e97

    You can also check:

    https://support.Microsoft.com/en-us/KB/953367

    Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

  • Compaq dc7700 sff: motherboards latest include the compaq dc7700 sff case?

    I want to use the case of an old dc7700 sff, but the layout of the Panel back looks like it is the inverse of all the motherboards I've found. Is there any motherboards that support DDR3 RAM and have at least three connectors SATA (SATA 3 preference) that will be adapted to this case (PCI ports on the left instead of right of ports)?

    Hello:

    Unfortunately, there is not.

    The dc7700 was the last model that used the case that has also been used d530, dc7100, dc7600.

    When the dc7800 came out, they used a completely different case, which was also used on the dc7900.

    Then the case was changed again when the 8xxx models Elite have been introduced.

    The first business office of HP in this class that came with sata ports 3 was the 8200 Elite SFF/CMT.

  • HP Elite 8300 SFF: his low profile card

    I have an Elite SFF 8300 and am looking for a card low profile with coaxial output so that I can use it on my sound game of boston that has a coaxial input. I tried without success.

    Thank you

    Thank you for the information, @PeterHB.

    Here are the system requirements for the card:

    The system configuration required
    • 1.0 GHz Intel / AMD CPU
    • 1 GB OF RAM
    • A free PCIe slot
    • A free location for the digital expansion
    • Internet connection for downloading drivers and software
    • Microsoft Windows XP/Vista/7/8

    The card is compatible with Win 7.  However, I have highlighted in orange system requirements you must check to ensure that they are available.  Apart from that, I think that the card should work.  I always offer the check with the Technical Support of the manufacturer is a good choice.  They are the experts on their products.

    Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

  • 8200e graphic sff updated card?

    Hello

    Can someone tell me how big a graphics card can I put in a HP 8200e SFF?

    Is the system locked to standard som HP graphics cards or can I put with any card I want?

    Thanks in advance :-)

    Concerning

    / Bass

    Hello:

    I recommend that stick you with the video cards listed as supported for your Elite SFF-8200.

    240W power supply does not manage much more.

    Supported video cards are listed on the link below on page 14.

    http://h18000.www1.HP.com/products/QuickSpecs/13879_na/13879_na.PDF

    If you would rather try another map those listed that would work with your P/S, then it may or may not work.

    They are not necessarily locked work.

    Paul

  • Graphics card suited Elite 8000-SFF

    Hello

    I want to update the graphics card for my desktop SFF PC: HP Compaq 8000 Elite SFF (Intel Core 2 Duo E8600 3.33 Ghz processor, 4 G of DDR3 RAM, Intel GMA 4500). I know that the Radeon HD 6350 will work well in my system. Could you please recommend a graphics card for my system is better than the HD 6350? Radeon HD 7750 half-height works well?

    Thanks in advance

    You know that the limit will be this anemic 135w power supply. He'll be a card low profile bus-powered.

    I think you have done your homework well because as best as I can tell, the low profile 7750 HD is your best bet:

    http://Icrontic.com/article/Sapphire-Radeon-7750-low-profile-review

  • DC7700 Small Form Factor: BIOS of HP DC7700 SFF

    I have a DC7700 sff desktop that was running Windows 10 with a glitch. With each operating system installed (LInux or Windows), I saw an error memory 4 intermittent beep. I have reinstalled the memory, replaced the modules, and nothing seemed to help. Food seems to be good and I was able to use the machine with two additional hard drives attached to another hard drive cloning.

    To try to solve the problem, I tried to upgrade to version 3.05 using the method of updating the F10 BIOS setup menu. The system has reached 70% and then didn't update. Now, it does not start. I found a method online for the resettlement of the BIOS, but all forums seem to have old non-working links to the updates to the BIOS. The description of the BIOS flashing utility indicates that it is to change the splash screen. Can someone tell me please to the correct location for the latter. BIN files? Thank you!

    Hello:

    4 beeps is a power supply issue.  5 beeps is a memory problem.

    Business support pages are missing a lot of pilots.  HP is aware of the problem, but I don't know how long it's going to be to fix it.

    Given that your BIOS is v1.01, you need to follow the progression of xx 1.  3.05 was for vPro models this is why flash BIOS probably did not work.

    I have compressed upwards and attached files you need an old thread that I have helped someone else with below.

    It will bring your BIOS to v1.16, who was the final version.

Maybe you are looking for