HP DesignJet T7100 printer: Can 'HP 761 grey 400 ml of ink (M995A)' replaced by 'HP grey 761 dark 400 ml of ink (CM996A).

Similar Questions

• HP Designjet T7100: Designjet T7100 continuous long print document

  My plotter is on the local network and works very well.  I have a PDF file that is much larger (longer) that these are great.  Due to the large amount of information on the layout, the police is very low.  This means I have to print large drawing that I can do. If the drawing prints to the maximum width of paper of the plotter scale is sufficient (font is readable).  The print dialog allows to break the document into separate poster sized pieces, but I want to print the whole thing on a piece of paper continuous time.  It's theoretically possible, but I need to figure out the correct settings.  Anyone has experience with this, and you can post the appropriate settings?

  @Douglas_Phelps

  I don't have any experience with your printer model, however the User Guidesays that you can create a custom for your printer paper size and that would be useful.  See Chapter 9, Page 80

  A few general ideas

  Because you cannot create a larger custom paper size that the driver can handle, you can create your custom paper size to be longer than it is wide, and then perhaps to print the document in the landscape, which actually has the orientation of 90 degrees.  Note: Depending on your printer software, you may need to log outgoing/incoming or restart the computer to see the new paper size in your list.

  You can try to open the PDF file in Adobe Reader MS> file > Printe > print preview (open)

  Depending on your printer driver software, you can maybe open properties and fnd the paper size option.  The custom paper size should be listed.

  Another option of interest (in print preview mode) > under sizing Page and handling > Poster

  If the poster is not useful in this context, or if the paper size is elusive (assuming that you did create a model appropriate to the custom made size, try selecting "source of paper to choose depending on the size of Page PDF.  NOTE: By selecting poster appears to eliminate / reduce to zero the possibility to choose paper...

  Also on the homepage of the print preview > option to change orientation

  Now, I don't know if this will actually work - I have a OfficeJet Pro 8630; It does not print the wonderful, long, rolls of paper.  The smile.  It may be a few minutes of your time to play with the settings.

  There may be information on what you need to be mentioned the User Guide - it is quite broad - or there may be something useful in another manual from those that are available to the Web site of your printer Support pages.

  Your printer:

  HP Designjet T7100 printer

  General reference:

  Manage the print with preview output before printing

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• HP Designjet T2500: How can I scan documents without using the main table with the HP Designjet T2500 printer?

  Hello, in my office we recently bought printer HP Designjet T2500 and, so far, works great but I have a doubt with the procedure of the Analyzer in the case where the main panel is malfunctioning. How can I scan a document without the help of the main panel or a plan?

  I know the printing can be done with the supplied software, but he made no reference to the case where we need to scan a document.

  Any help will be great, thank you.

  Hello

  Analysis cannot be done froom the front panel of the printer.

  If you have a problem with the Panel, you will need to repair the device because you won't be only able to scan, as you will not be able to load paper or calibrations.

• My Epson stylus NX300 printer is printing very light. I'm not black ink. What can I do?

  The glass is normal, telling me 'copy' and 'simple letter '. When I print, it comes out grey. I can't change the cartridge except tells me the glass.

  Hi Sharon

  This questions the printer head problem. see the following steps for cleaning print head:

  Click the Start button, if you have Windows XP. If you have Windows Vista, click the Windows icon located in the lower left corner of your computer screen.

  Click on "Control Panel", then "printers and other devices. Finally click on "View Installed Printers or fax printers."

  Right-click on the name of your printer and choose "Printing Preferences". This should open a new window; Then look for a tab or button labeled maintenance, or something similar.

  Find the button that says "Print heads" or "Clean print heads" and click it. You may be asked to choose the print heads; Choose them all if you are. Make sure that there is no paper and ink in your printer, and it is turned forward.

  Remove the page that your printer has printed and see if there are the missing gates or boxes. If it does not exist, you can just exit the program - your print heads are not blocked. If there is missing grids, then click on the "cleanup" or even button labeled.

  Once you have finished the cleaning, print another page to make sure that your printheads are is more clogged. If they are still clogged, repeat steps 1 through 5 until your printer is printing clearly.

• impression of Pro to Z5400 Designjet HP printing problem

  Last October, I bought a Postscript Designjet Z5400 printer. On both CD and software down loaded from the Web site called "HP printing Pro" produces an error on the screen of the printer "Incorrect, impossible to print file Format". This happens with. JPG. PDF and. TIF (any graphic file) files.

  The printer precisely will not respond to the controls of Photoshop CC either. Try to compose a set of 5 "x 7" photos in the upper part of a 36"wide roll of results of paper in the images printed on one side of the paper with massive losses." The problem seems to be that the printer will not allow a page size to create what is shorter than the width of the paper.

  I have been in touch with HP about this and offered a refund, even if I sent my own to the printer, not me Bank evidence. Answers like "It's a HP offer for you, not the finance co" suggests HP trying to me to commit larceny as a custodian... A criminal offence.

  I did not buy this printer for a refund, I bought it for a living with. Twice now, I tried to access the part "next day guarantee support" of the Pack in customer care, I paid an extra $1200 for and not received a response.

  I am able to print to this printer, but not using the software from either HP or Photoshop CC. Any help here as to who speak for the "next day" service, I bought or the highest level of management, I can access complaint with all the terrible service, I was making would be apreciated. I have a video broadcast quality of the mess that occurs when you try to use this printer, but I hesitated to post publicly until a person at HP has actually been and looked at the problem. It's either the printer or the HP software cause.

  Thank you

  Ryadia.

  Hello ryadia,

  I just sent you a private message.  If you are unsure how to check your messages from the forum, this post has instructions.

• Designjet T520 printing with ink cartridge empty

  can a t520 print (black) even if a color cartridge is empty or the printer stops all functions until the replacement of the cartridge?

  We intend to replace a hp not by a T520 tracer (go maybe later us to the 2500 series) and especially question is a "decision point" for "buy or not.

  Thanks for any official information on the subject.

  Best regards / WAG_Frutigen

  This forum focuses on the level of consumer products.  For the Designjet that you can have better results, post in the forum HP DesignJet here, this is where the DesignJet experts.

• Designjet 500 prints on usb but not ethernet

  I inherited a DesignJet 500 printer 24 in. I can print so that I am related to him by a USB cable but when I try to set up on my network, I can't print to it across the network.  I can ping the JetDirect card and can telnet in as well so I know that I have the correct IP address and it the card itself can communicate with my network.  I use the same driver via the USB port and the network port but still unable to print over the network.  Any ideas why I can connect to the printer on my network, but I can't print on it unless I connected locally with a USB cable?  I tried with a laptop running XP32bit and Win7 64 bit with the same results.

  Thanks for the help.

  Thanks to the entrance to the Forum of commercial products.  BTW, I discover to my problem.  It looks like the problem was the cable used to connect to my network.  One of the things that I should have checked first, but don't have.  After replacing the cable, I was able to print from the network to it.

• A laser printer can be plugged into a power strip?

  A laser printer can be plugged into a power strip?

  Here's the question.

  A typical wall outlet is rated at 15 watts max, but you should only put about 80 percent of this amount on the circuit as a constant pull then 12-13 watts is the actual amount of the charge, you will place it on one shot. You might get an occasional brief increased load when a device such as a printer laser heated.

  Laser printers pull a lot of power when the fuser unit, heating, so you should gave them a plug dedicated to the extent possible.

  If you put a printer into a power strip, then the band must be plugged into a wall outlet and the printer should be the only thing plugged into the power strip.

  End check model of your laser printer and find the data sheet and see how much current it draws pulling maximum amount, if it is 12 or 13 amp, then you really should have a dedicated socket or a power strip plugged into the Jack with nothing else on this subject.

  If my post resolve your issue please click the accepted solution inder button it. Thsnk a tech for a post click the thumbs up button under the post. You can even click on the two buttons...

• HP4215 printer can be used without phone connection if want to print, scan or copy

  Have a HP4215 printer that has not been used for a few years. Keep allow the family member, who use only a cell phone, and an old Apple laptop for 1 year, to be able to use it to print, scan and copy only - no fax.  If it downloads the driver, and hooks the USB, the printer can be used without a line of phone being installed?

  Hello

  Yes, given the portable computer Apple has USB ports, you can connect your printer to the laptop via a USB port, but you will not be able to print from cell phone. If you want to print anything from cell phone, the quick and easy way: send or copy on the laptop from Apple to print.

  Kind regards.

• My HP Photosmart Premium is saying "preparing the printer can not be interrupted. Please wait... "What is happening?

  My HP Photosmart Premium is saying "preparing the printer can not be interrupted.  Please wait... "What is happening?

  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/HP-Photosmart-premium-error-message/TD-p/1470957

  HP support

  Edit:

  I know that maybe it's a little late to come and see this post was several months ago, but I had the same problem.

  I ended up turning off the machine and opening printer and check the ink cartridges (I had seen just to find the part number for a new cartridge).  I found that the blue cover which snaps into place on the ink cartridges was broken not closed completely.  This has caused the printer constantly tries to go into maintenance mode, but it could never align cartridges.  She also told me that there is a paper jam, even when there is no paper in the machine.  I even let the maintenance run all night without success.

  Once the cartridges have been broken in place and the blue cover has been fully guaranteed, the printer worked.

  above compositions of this thread:

  http://h30434.www3.HP.com/T5/eprint-print-apps-mobile/HP-OfficeJet-Pro-8500A-plus-printer-is-stuck-in-maintenance-mode/TD-p/1207907

• Designjet 111 - printing problem

  My Designjet 111 printed 6843 pages. Almost all were 24 "x 36" CAD. Changes of cartridge & usual ink print head.

  Two days ago the plotter has stopped printing. It was a pdf CAD and got about 1/2 ", then stopped.

  Maintenance of the 532 system error codes:

  # 0, 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 1 S.06.04 SM 02.01: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 2 S.06.04 SM 86.11: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 3 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 4 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 5 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 6, 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 7 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 8 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 9 S.06.04 SM 02.01: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844

  Code of error starting Track = 167 = init PrintHeadControl

  I put in four new print heads with the same result

  Changed the ink also.

  Not sure whatelse to do to get the tracer is going?

  Any help would be greatly appreciated

  Roger

  SOLVED

  You have a printer independent guy tech $80, which has stripped the DJ11 and cleaned, inspected all parts.

  Nothing broken just a lot of cleaning.

  Head of transport that reads the MICR band was dirty.

  HP support (Vijay in India) was useless

  Hope this helps some other users DJ11

  Roger

• How can I change the SSID for my C4780 printer can find my wireless phone?

  I changed routers and got a new SSID.  Now I can't change it so the printer can find it.

  The best way to do this on a Mac would be to uninstall the printer completely and reinstall it with the CD or downloaded at HP software.

  Make sure you start by unplugging the USB cable.

  During installation, you can choose the option network and connect the USB cable when prompted.  Follow the prompts and it should get reconnected to the network.

  Here is a document from HP that details how to install this printer on a network.

  There may be other ways, but the lack of a configuration wizard wireless (due to the feature of the screen), makes the limited options.

• 8600 HP all-in-one more: 8600 wireless printer can accept dynamic address of the cable mode, / router?

  Got new Suddenlink cable modem/wireless router that uses dynamic addresses - only but the 8600 all-in-one printer uses static-how to to get wireless printing? The printer can be reconfigured to accept dynamic? How?

  Thank you

  Yes, it can, information in your printer manual. You can reset the network for DHCP settings. In addition, your router supports IP static. You just need to configure it. Info is in the router manual or call them.

• My HP Photosmart C309a printer can't find the router wireless 3 feet above him.

  My HP Photosmart C309a printer can't find the router wireless 3 feet above him.  I ran the diagnostics and got the message "the wireless radio does not work.  This device is the wireless radio?  In the router? In the printer?  I have reset the router is #6 with the printer, but I am still unable to connect my Macbook to the printer wirelessly.  My desktop Mac is connected to the printer with a cable and print well.  Is my router messed or my printer?

  Wireless radio of your printer (that it uses to communicate with the router radio) died.  Here's how to contact HP technical support: www.hp.com/go/totalcare

• dleecom.exe has been removed and know my computer and the printer can not communcate between them, what I can do

  in my firewall settign my computer and the printer can not communcate between them hit the wrong button because it was working fine

  Flight23,

  Run first remove print jobs to remove all blocked the queue print jobs.

  Unplug your printer,

  Start, Panel, programs and features, your printer, uninstall.

  Restart your computer.

  Make sure that the printer has been deleted. Driver Manual printer removal

  With online computer, insert the floppy disk to the printer and reinstall the printer. You will get a message, the printer is not connected. Connect the printer at the moment (power on)

  Don't forget the programs anti-virus and firewall will block communications.

  Rick