HP Deskjet 3050 a: HP all-in - one Printer Installation remotely

Similar Questions

• DeskJet 3050 has J611 all-in-one: Mac cannot connect to the printer using the wireless configuration

  My printer is connected to the same network as my Mac. When you complete the Setup wireless using a USB in system (HP Utility) preferences, a message says: "wireless network settings have been successfully downloaded to your device. However your Mac could not locate the device on the network. »

  I did everything I could: restart the printer. Unplug the printer and reconnected on the network and configuration of try again several times.

  Help?

  Hey @benjaminllim,

  Welcome to the Forums of HP Support!

  I understand that you have some problems with the connection of your Deskjet 3050 has e-all-in-one printer to your computer Mac OSX 10.11. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  1. Turn the printer off:
  2. While the printer is turned off, disconnect the power cable from the back of the router for a minute.
  3. When the lights come back on the router, turn on the printer.
  4. Disable any antivirus, firewall or security of your Mac software.
  5. Try to run the installer.

  Please let me know the results after following the above. If you are able to print to the printer, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• HP Deskjet Ink Advantage 2515: HP Deskjet Ink Advantage 2515 all-in-One Printer - software for scanning will not open

  I'm having the "HP Deskjet Ink Advantage 2515 all-in-One Printer" for more than a year now.

  I was previously using Windows 7 Ultimate and there is no problem.

  I did a clean install of Windows 7 SP1 Ultimate and then installed the HP software.

  The printer function works perfectly.

  The only problem is that the software of the Scanner itself does not open.

  Measures taken to correct.

  (1) uninstalled the drivers and the HP printing software. Rebooted the system and did a clean installation of the printer software and drivers who stood on the site of HP.

  (2) Ran "HP print and Scan Doctor", it says "Windows (WIA) Scan Error".

  Don't know what that means. Please help to guide how to correctly do the work of the Scanner Software.

  Thank you best regards &,.

  AJ

  Hi @AJ_Gem,.

  I see you have some analytical problems after doing a clean install of Windows 7 SP1 Ultimate. I would like to help you today.

  The WIA drivers are part of the Windows operating system.

  Run this made it Microsoft tool to see if it will solve this problem.

  Diagnose and automatically repair Windows files and records issues.

  I tabled this document, just to make sure they are the same ones you had checked.

  This document is to check the services of Windows Image Acquisition (WIA).

  Windows: Digitization of HP Software Does not open or Scan to a printer using a USB connection.

  Do not take into account the title.

  Proceed to Solution 3: check the Windows Image Acquisition (WIA) services.

  Temporarily, run Antivirus software and try to scan the image.

  If the problem persists, download and try to repair the WIA drivers. If you don't feel able to do these steps, you can contact the computer manufacturer or Microsoft to solve the error WIA.

  Back up the registry first.

  How to back up and restore the registry in Windows.

  Restore default startup for Windows Image Acquisition (WIA) Type.

  Please let me know the results.

  Thank you.

• HP-All-In-One-printer installation

  uninstalled HP All In One Printer because it did not work properly. Now, it will not be installed. I get a window that States cannot be installed by using the command "run as" and to log on as a user with administrative privileges. I am the user admin privileges (the only user of this computer). This is the 2nd time that happened last year. I don't remember what I did last time. Please help me!

  http://welcome.HP.com/country/us/en/support_task.html

  Click on the above link for the drivers and how to install it, etc.

  http://welcome.HP.com/country/us/en/contact_us.html

  For any other problem, contact HP at the link above.

  http://h30434.www3.HP.com/

  Or try the HP Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• HP Deskjet 3050 has e-all-in-one: impossible to download drivers and software Web site

  I have seen this problem posted a few more times, it seems that it is recurring.

  I reinstalled Win7 on my machine.  I try to reinstall the driver and software for my all in one.  I get ' HP is compile your results. " It could take up to 3 minutes, depending on the speed of your computer and connection. Thank you for your patience. ' message for more than 10 minutes now with only the busy indicator.  I tried this on Chrome and IE with the same results.  Help.  I need my scanner.

  The pilot site is always questions, but you can download the driver Windows 7 x 64 for the HP Deskjet 3050 a directly from the link here:

  http://ftp.HP.com/pub/softlib/software12/COL37193/al-109013-3/DJ3050A_J611_1315-1.exe

• Cannot install driver for HP DESKJET 3050 a j611 all-in-one using windows 7

  Stagnate in the printer, but can not find a driver. Have tried to set as the default printer, but right click I only get CREATE-HELP-DELETE SHORTCUT-PROPERTIES of the DEVICE can someone help as HP are useless

  You don't install it correctly, but just pluged in there.

  It must have taken all of 10 seconds to locate your model on the site of HP

  You install using the cd of HP, or the full functionality of the HP site download and does not connect until the installation says to

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4062&LC=en&cc=UK&DLC=en&sw_lang=&product=5061092

• DeskJet 1050 J410 series: 8.1 Windows & Deskjet 1050 J410 series all-in-One Printer/Scanner

  I just took delivery of my laptop Lenovo (windows 8.1) & seeks to activate/use my printer Deskjet 1050/Scanner. I am informed that the Deskjet software is installed BUT I can't progress further. I searched HP Scan & Capture screens & read the "ratings & reviews" (they are not easy reading!)  BUT cannot find how to progress further, between all of this "irrelevance", it seems to me information.  Everyone there to advise me

  Hi @RACONTEUR

  I'm not sure I understand. You say "I am informed that the Deskjet software is installed BUT I can't progress further," what you're doing now, but can't?

  While I wait for you, please use the print HP and doctor Scan. Printing HP and doctor Scan is a free utility (tool) that allows to quickly solve common printing, scanning and connectivity problems, including but not limited to:

   

• 5520 all in one printer installation does not

  I have installed and uninstalled the software several times.  I used the wizard of HPinstall nothing works.  My problem is that when I click on the desktop icon for your printer, or in the all programs list, 2 files will open to another andnothing.

  The 2 files are:

  HPSPProgress.hta

  HPSolutionsPortal.hta

  I don't seem to have capacity toget one kind of control of the printer control panel (should I?)

  Anyone have a suggestion?

  Hi brisargr,

  I think, from what you described, that the problem is with the HP printer Assistant. Please use the following to resovle the question paper. HP Printer Wizard opens with an error in Script or in Notepad.

  If this does not resolve the problem, please post back with a screenshot of the error you see. How to take and post a screenshot on the Forum of Support HP.

  Thank you.

• C4795 all-in-One Printer installation

  I would like to install my C4795 printer to another computer and I don't have the operating manual or the installation disc.  Is there a way to do it with the disc or if I order a disk somewhere?  Please keep in mind, I'm no computer in order to have the disc all savvy would be probably better for me because it literally takes you step by step.  Thanks in advance!

  You download the User Guide and follow the instructions on the installation with a USB cable?

• Printer HP 3050 J610 series all in one will not print any documents

  I'm on Windows 7 Service pack 1 and I have a HP Deskjet 3050 J610 Series All - In - One Printer.it is not wireless I use a USB port for printing.   I have problems printing pdf files as well as Word documents.  I uninstalled and reinstalled the software and drivers; I have restarted my computer several times; I tried the scan doctor and he says everything is fine.  It prints the test pages.  When I press the icon of the printer, it will save the file even if the file is saved to alread. I'm going to planet and save the file again.  I noticed that, for files, it says printer and no .doc or .pdF files.  He also says that it is offline.  I tried the steps recommended for this suggestion has as well and still have problems printing.  The I am trying to print the files aren't new documents except one which is a pdf file.  I hope you can help me.  The window pop up that appears just before printing a 0% for printing.  I hope that makes sense.

  Thank you.

  Maria Holloway

  HI Maria, welcome to the forums

  I noticed your post about the problem you are having with your Deskjet 3050, printing via a USB with Windows 7. I have some suggestions that I would like to offer that can help!

  Perform a clean boot and make sure that your firewall is disabled: Disabling and Re-enabling your software firewall in Windows.

  By this stage and test print while the start up programs and the firewall is disabled, it will show if the mobility programmes have been the origin of the problem.

  Now try to print a document as one. PDF or. DOC.

  If it does not, as a workaround option, try to save documents that you have an impression of question as a different file (do not use in .doc or .pdf format) type.

  Open Word or Adobe and print a blank page (without saving the document) to see if you have a problem with printing.

  Please let me know the results, I hope that my information helped!

  Have a great Wednesday

• Destjet HP 3050 has j611 all-in-one series does not not on windows 8

  I got Hp Deskjet 3050 a j611 all-in-one series on my windows 7, I've upgraded to Windows 8 and my printer did not work properly so I uninstalled so I could reinstall it, but it will not install because it says that it is not compatible. is it possible that I can make this printer work using Windows 8?

  Hey kelyka1,

  I guess you are trying to reinstall with the CD supplied with the printer.  Click on the link below to access the download page for the driver for Windows 8 for the Deskjet 3050 a J611.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-109013-2&cc=us&DLC=en&LC=en&OS=4132&product=5061082&sw_lang=

  I hope this helps.

• HP Deskjet Ink Advantage 1515: stop the test page printed for all-in-one printer, HP Deskjet Ink Advantage 1515

  How can I stop my HP Deskjet Ink Advantage 1515 all-in-One printer to print a test page everytime I STARTED printing?

  Hello JoshSimon ,

  Welcome to the HP Forums.

  I see that you have a problem with the printer printing before you print a test page.

  If you turn off the printer at the end of the day, please do not.  Turn the printer on/off will result in printing a test page.  If you are concerned about the printer lost power, and that's why you stop, the unit actually built in sleep/stand mode that will kick in when you are not using the printer.

  Once a print job is sent to the printer it then wake up and do the task at hand.

  In addition, make sure you have the printer power cable connected directly to a wall outlet and not a bar/power strip. Here is a document that uses a LaserJet printer for example, but it is intended for HP products in general. Please click the link which explains the problems when connected to an uninterruptible power supply/Strip/surge protector power.

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  See you soon,.

• I have HP Deskjet 3050 a all-in-One Printer - J611g and need help with printing, please?

  I just bought the HP Deskjet 3050 all-in-one printer-J611g a. The manual has shown to do the printer double-sided printing odd pages then only print even pages only, and it works very well for one page on one side of the sheet. However, when I want to print two pages on one side of the paper and another of two pages on another aspect of the sheet, print the odd pages or even pages only just does not work! Ditto to print more than one PowerPoint presentation on one side of the page, if I click on print the odd pages only, then the printer will display the odd number of powerpoint slide instead of print odd number. I used to have another printer HP Officejet and never had any problems with two-sided printing. This printer comes with the function double-sided printeing at all?  If so, how can I do duplex printing?

  Thank you very much!

  This is a limitation of the software that you use and how the HP printers recognize the incoming files. When compress you multiple pages on a single "page" this page is actually two pages, with even and odd numbers. It is therefore difficult for the software to determine the page numbers 'odd' and 'even' when printing, because it is no longer applicable to the relevant pages, but the format in which they are being printed.

  I hope this information is useful!

• DeskJet 2544: 2544 HP Deskjet all in one printer series No. CN4172BO1M

  Hi, I have a problem with my HP Deskjet 2544 printer all-in-one [personal information deleted], I experience a gray line through the text the two lines that makes text blurry and difficult to read.

  I cleaned and aligned the print heads, changed for a better print quality that has helped a little, but the line is still in the text, can you please advise.

  Hi @oldfeller1,

  Thanks for joining the Forums of HP Support for a solution to your printing problem.

  I understand that you are using an all-in-one printer HP Deskjet 2544 with a Windows Vista PC and printed text is blurry and difficult to read because of the grey lines through all the lines of the text of couple. I would like to help with that.

  Here is the document of support designed to be used with this type of problem - fixing poor print quality.

  Please let me know if that solves the problem, or if you need assistance.

• DeskJet 1510 all-in-One: the installation of the software has failed after the USB connection and remain unfinihed. Work for printer and Scanner

  My PC Dell XPS401L has been updated to Win 7 Win 10.  Then, the HP DJ1510_188 software has been installed.

  The task was ok until the bond required of the Dekjet to the USB port.

  Heard the noise of the acknowledgement of receipt, but there screen remains unchanged despite I wait several minutes. So the installation remains unfinished. However, the printer and scanner are both of the device but are not available important "Solution Center" screen.  I already have the solutions of the error indicated by HP support withot success.

  The system indicates that the problems appear in the USBsetup.exe

  Can someone help on this subject?

  Horacio

  Hi @Horacio_B,

  Thanks for joining the Forums of HP Support for a solution to your installation problem.

  I understand that you try to use an all-in-one printer HP Deskjet 1510 with a PC that has been upgraded from Windows 7 to Windows 10 but does not complete the installation of the USB and the HP Solution Center is not available. I would like to help.

  I would like to start by disconnecting the USB cable and uninstall all software related to printers. Here is a support document which can be used if necessary reference - uninstalling the software of the printer (Windows).

  Once it's over try to use the HP printer installation wizard for installation. This tool will get the software and installation help.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!