HP deskjet 3055a: can't choose my network on the printer hp deskjet 3055a

Similar Questions

• hp 8600 printer cannot be contacted over the network and the printer is not enabled.

  hp 8600 printer cannot be contacted over the network and the printer is not enabled.

  the HP software installed on the PC on the floor. Print wireless from PC upstairs and the PC in the basement on the network for the last month up to yesterday

  Now to receive above - two error messages cannot be contacted ove RL network and the printer is turned off.

  Reality - the printer IS on and the PC on the floor can print to the printer.  Network on the printer symbol says it is connected to the network.

  a reason any PC in the basement all the cant suddenly find the network and the printer?

  Hello

  The first thing I would do is follow step 6 in this document to set a static IP address: http://support.hp.com/us-en/document/c02817031
  When it askes for the DNS information, enter in Google DNS. Preferred DNS = DNS Alt = 8.8.4.4 8.8.8.8

  This could increase the stability of the network connection to the printer downstairs.  If this does not help, let me know what OS is on the computer causing problem, because that could cause a problem?  Other than that, you can check the quality of the signal you get form the network and see if this can be a problem.

• How can I get my USB to the printer wirelessly to a network without a computer?

  If you have a USB port to the wireless printer and no computer to use software to do this and do not want to use the WPS option (or it is not available), then the following method can help.

  That doesn't get a key USB Wi - Fi, as the printer Deskjet 3512, on the wireless network when there is no computer available.  However, this can work from a computer as well if you prefer not to install the software.

  For these steps, I'll use an iPad.

  1. the printer will broadcast a wireless network of its own.  This has usually HP Setup and model of the printer in the name of the network.  Connect a wireless device to the network.

  2. Once connected, open the browser.  In my case, it's Safari.

  3. Enter the 192.168.223.1 address in the address and press go to access the status of the printer page.

  4. once there, there will be several tabs at the top.  Select network.

  5. Select the wireless configuration wizard.

  6 Select next at the bottom.

  7. it looks for available networks.  Select your network from the list and click Next.  The network should be highlighted, select it again if it's not.

  8. you will be asked the password.  Enter the password and click Next at the bottom.

  9. the printer should now be connected to the network.  It may take a few minutes to share.  Reconnect the computer or mobile device to your regular network and it should be good to go.

  I know that there are some users who have only a Tablet and a USB port to the printer wireless with no other way to get it on a network.

  I hope this information is useful to someone.

• How can I save any network in the list of known wifi connection?

  I have a problem on the wifi connections. I can handle known wifi connection in the settings menu, but I can't select which connection is approved for me. Windows choose random connections, some of the known list of registered, some not. Even if I select "connect automatically" number of connections were not on the list of known link, especially my home network is a problem in this regard.  How can I add my home network to this list?

  Hello

  Thanks for posting your query in Microsoft Community.

  You can try to remove unknown connections to the list by clicking on them by clicking on "forget this network". To manage and save the other connections, now, I ask you to refer to try the suggestions in the article below and check:

  Manage wireless network profiles

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• HP Deskjet 3050 J611 series: I can't remove a document from the print queue

  My printer has an element 'stuck' in the print queue.  It got stuck when I accidentally turned off the computer until the print job has finished.  I use the "remote" printer, that is to say through the network. not with a printer cable.

  I tried to remove it, I went to the Control Panel, etc., I tried HP Support Assistant - nothing works.

  I tried to turn off the computer, printer and internet router for several minutes.

  The print queue of the printer says "delete", but it has been like that for 12 hours.

  I can not print anything else!

  Help, please!

  Yes, after the restart I had to go back in the case R Windows to run, and then in the print spooler and press start and the printer came back without the stuck paper.  Thank you very much!

• How can I connect my netbook to the printer on the same wireless network?

  My home wireless network is well established and includes a wireless printer.  I'm usin my HP netbook now and for the purposes of the internet, it is connected to the same wireless network.  However, I can't the netbook to detect the wireless printer so that I can install it.  Help, please.  Thank you

  It is often easier - especially with the HP printers - to launch the installation CD for the printer to the new computer and let the installation program find the printer for you.  (But I forgot... your netbook is not a CD player.)  You could try to copy the files from the printer installation CD - if you have a CD, a USB key and use it to install the printer.)

  I support this.  HP drivers to connect to printers more easily when you allow the installation of the driver detect the printer.  I had several HP devices and their installation is smooth when I do that.

• DeskJet 3522 printing scanning copy: hp dj 3522 disconnects wireless network when the printer is turned off

  I have the above printer.  As indicated, it disconnects from the network when it is off.  I have a Westell A90 750014, MAC, disabled filtering router, the printer has been added in the MAC filter table, and in the wireless station status is listed as "associates".  When I reconnect once disconnected from the network, I am able to reconnect using the simple push button config method.  Can someone tell me a way to feel connected to the wireless network.  Thank you very much for your help.

  Hi @scotty1963

  I understand that you have problems with your printers wireless function despite all your efforts. I'm sorry to hear that, but it will certainly do everything I can to help

  Please use the following document to solve the problem and I would like to know the results of your efforts; The printer keeps Wi-Fi connection.

  I hope this helps.

• When ISE goes down, none of the computers can get to shared network or the Internet.

  We only run Cisco ISE 1.4 with only computer authentication and recently had a power outage for about 6 hours. When the batteries of the UPS drained EHT servers are connected to the, none of the computers could connect what either. The NETWORK card on the computers had an error authentication failed. We "Rescue of unauthorized network access", selected on each computer. Is there a way to allow all computers access to the network and the internet as usual when the ISE servers are down?

  The port configuration is less to:

  switchport access vlan 77
  switchport mode access
  switchport voice vlan 777
  IP access-group ACL by DEFAULT in
  authentication event fail following action method
  action of death event authentication server allow vlan 77
  living action of the server reset the authentication event
  multi-domain of host-mode authentication
  open authentication
  authentication order dot1x mab
  authentication priority dot1x mab
  Auto control of the port of authentication
  periodic authentication
  Server to authenticate again authentication timer
  inactivity timer 180 authentication
  restrict the authentication violation
  MAB
  no link-status of snmp trap
  Auto qos voip cisco-phone
  dot1x EAP authenticator
  dot1x tx-time 10
  QoS trust device cisco-phone
  spanning tree portfast
  spanning tree enable bpduguard
  service-policy input AutoQos-VoIP-entry-Cos-policy
  service-policy output AutoQos-VoIP-output

  You must use a script of EEM to change the ip access list that you assigned to the interface, to something with "permit ip any any" inside.

  'action dead event server authentication allows vlan 77' won't work that in configurations in closed mode, do not use an acl of pre approval.

• How to choose a bin of the printer to print a pdf file

  I need to print a pdf file from a specific printer tray. I have a mac and you use acrobat adobe DC. I can't find this option anywhere in the printer dialog box.

  Hi lucyk,.

  Since it is a function of the printer itself, you'll want to click on the printer in the lower left corner of the dialog box print of Acrobat. Click OK to the message that appears. You should be able to choose your paper source in the settings of the printer-specfic.

  Best,

  Sara

• HP Officejet Pro L7600: Can you please tell me if the printer HP Officejet Pro L7600 is able eprint?

  I try to print from a tablets KindleFire HDX and Samsung Galaxy Tab on my HP Officejet Pro 7600 but have not found a way to do it.

  Hello spikeforce,

  HP Officejet Pro L7600 is NOT capable of eprint.

  However he manages wireless printing. All you have to do is to have the printer connected to your wireless network.

  Also to connect your Samsung phone / tab and Kendle to your wireless network. You need a HP printing application to print using Samsung tab.

• I can't remove an item from the print queue that is not allowing me to print

  I'm deleting a document in outlook from a HP Color Laserjet CP1215 printer yesterday, and because it is not to delete, I can't print more. Help, please.

  Hi Sierris,

  This document can be blocked in the print spooler, as would be the case sometimes.
  To check the coil:
  Start on your C: drive. Go to the Windows folder, then System32 folder, then the folder of spool, then the Printers folder.
  If there are any files in the Printers folder, delete them, and this can solve your problem.
  Hope this helps and post again if you need more help.

• How can I scan a document from the printer to my pc and find it once it is scanned

  I need basic step by step, I'm a newbee how scan a document from the printer to my pc and then find it once it is parsed on eprint D110 HP photosmart wireless

  Thanks for any help you can give.

  Press scan on the printer display, and then select the computer once scanning is finished it should open automatically with a default name for example scan001. If it's not automatically, you can find it in My Documents > my Scans

• How can I copy a document when the printer display always flashes missing cartridge message?

  HP D110 has x, os XP: is it possible to replace the touch screen to copy a document when a cartridge is missing and the display will show only this error message?  The black cartridge is there and I can still print.

  Hi mrmarquar,

  There is no option to print or copy without cartridge into the two slots in the cartridge. The printer needs a cartridge into the two slots, even if the Habs ink is low, it should always copy in black and white.

• How can I "Enable bidirectional Communication" on the printer?

  I need whereas my printer in my hard drive again.  I put it again and now I can not anything on this subject.   But he came to say, please turn the settings to "Enable bidirectional Communication" on the printer properties dialog box.

  I don't understand what you mean by, "I need my printer whereas in my hard drive once again" unless you try to say you want to reinstall your printer.

  To enable bidirectional support, click on:

  Start-> Control Panel-> devices and printers

  Right-click on your printer, and then select printer properties. Now click on the Ports tab, put a checkmark in the box down to enable bidirectional support , and then click OK.

• I can't choose Canadian dollars during the sampling of a DC plan?

  Right here https://creative.Adobe.com/plans there is no option for Canadian dollars when choosing a plan.  So I'm stuck picking U.S.?  When the dollar fluctuates, I get to pay more or less every month?  It's not fair.  I hope you add Canada option from.

  Lunchababe, right now, we don't have the possibility to pay in Canadian dollars. Thus, you pay in US dollors only.

  If all goes well, in the future we could also add but don't know when.