HP DV6 of the computer stopped working after the update of the Bios and Memoryupgrade

HP DV6 - 3161EO

XE068EA #UUW

Hi, I bought a brand new HP with Intel I5 processor computer and GUI double, its been working well so far and I thought that I should upgrade the Bios and memory as well.

So I did, I bought memory 10600 and crusial 12600 and corsair, a single and two put in correspondence of the sticks, just to be in business, and I've updated the bios. of F.13 to F.29

http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=SV&CC=se&DLC=SV&sw_lang=&product=4344...

The computer worked perfectly for about 4-5 hours, then there are allmost quite dead.

Ive tried to pass on different memorycabsm like the original samsungs that came with the computer.

Ive tried the famous "hard reset".

Nothing, the computer starts "boots" but don't approach the entered message turnes off.

Presedure same each time.

Any memory I put in, the same result.

Ive used different powerbricks, turned of the computer resets hard, between 10s 2 min, picked up the bios battery, has offered free energy.

Let the rest of the computer for half a day, put it all together exept cmos battery = exactly the same as before.

"take out all the memories and the computer works and get that caps lock flashing light.

So my question is this

Why you encourage people to update, when it's clearly the fault at hand.

Sell your computers with 8 GB of ram from the beginning so the people do not have upgraded later because your hardware is not able to manage different memorycaps of accepted and authorized as crusial or corsair providers.

Ive built perhaps 50-60 computers and had about 10 laptops and NEVER had a fault like this.

My laptop $1200 is useless, and I actually held you at HP responsible of it.

The computer is of course out of warranty, so its my own falult, as usual.

«A simple question, is there a way to 'force' a new bios on the Board, without memory of the computer, because it is the only time where it works and works welll.»

Thnx, 'a sick owner HP.

For later use, it's really kff upward, but I got it working again.

1 changed the original memorycabs for much faster, 1600 mhz, I know that this mobo doesn't support, but he did start the computer, so I could run the Windows + arrows Bios recover.

Installed the HP bios tools F10 + GIS and it worked.

so I guess I have to myself a thank you and a boost of the kudosbutton, hahah

Well, when your computer went down, don't give up and try everything you can, this prob took me about 3-4 days to eradicate, but now its working again.

See you soon

Tags: Notebooks

Similar Questions

  • My illustrator CS3 has stopped working after I updated my OS to Yosemite 10.10.5

    My illustrator CS3 has stopped working after I updated my OS to Yosemite 10.10.5, but my InDesign and Photoshop work very well. How can I get Illustrator to start working again?

    NOTE: I read a previous thread on the opening of the Java Control Panel in the system preferences (because I installed the new java my computer asked me for marketing immediately after in the new yosemite), but there is no icon Java not found. I installed this new java download more than once and still can not find it. Help!

    olou,

    If the suggestion on possible recording by Larry fails, see this page

    https://www.Adobe.com/account/my-products-services.html

    I'll try to ask a personal forum friend who knows what to do.

    For download, read this

    http://helpx.Adobe.com/Creative-Suite/KB/CS3-product-downloads.html

    and update, see

    http://www.Adobe.com/support/downloads/product.jsp?product=27&platform=Windows

    http://www.Adobe.com/support/downloads/product.jsp?product=27&platform=Macintosh

  • laptop keyboard stopped working after Windows update.

    have a toshiba satellite A505 laptop and the keyboard stops working after Windows Update reboots. We reinstalled Windows 7, which fixed the problem until the updates have come. Now the keyboard is unresponsive. Sounds like a software problem, no material. Also checked the keyboard drivers that are up to date.

    As a first response, go to the control panel, device, keyboard, keyboard Manager and right click, uninstall it and let it rediscover Windows and then reinstall it.

    It suits it much of the time.

  • "First Pro CC 2014.2 has stopped working" after a few moments of running and usually after you import a video clip.

    "First Pro CC 2014.2 has stopped working" after a few moments of running and usually after you import a video clip.

    I use a Lenovo T440p with Intel Core i5 @2 laptopp. 60 GHz, 8 GB of RAM. Windows 7 64-bit with Service Pack 1. Intel HD 4600 graphics card. All the drivers are up to date.

    All other non - CC Adobe video editing programs work.

    Help, please. Thank you.

    Dennis,

    Changing the video rendering engine should have solved the problem. Is it still pending?

    Thank you

    Regalo

  • on dv6 fingerprint reader has stopped working after installing Norton 2012

    Fingerprint reader has stopped working after installing Norton Internet Security 2012 on both of my notebooks from HP.

    Product name: HP Pavilion dv6

    Operating system: Windows 7 64-bit

    Error message in Device Manager under biometric devices in Device Manager displays an exclamation mark beside validity sensors (WBF) (PID = 0018). The following message is under the general tab: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) ».

    Driver is present and seems to be up-to-date.

    Appreciate your help.

    I have finally isolated the problem of my software lack of HP dv6 fingerprint reader. I think Norton Removal Tool, available online at www.symentec.com/nrt, was the reason. I am sure this conclusion because the exact same problem occurred after I installed Norton Internet Security 2012 on laptop HP same as my wife. I tried, in vain, to uninstall and reinstall the driver for the biometric fingerprint device provided by Validity Sensors, Inc.

    After spending a day and a half to try to "solve" the problem, I decided to restore my system and go back to the prior agreement of the point of the installation of Norton. Thank you HP to make this process quick and painless. Don't forget that if you installed anything after the restore point, it will have to be reinstalled.

    Fortunately, there's a less intrusive on CD of Norton removal tool. This utility uninstalls an older version of Norton you are requested to restart and then installs the latest NIS. It is a method of removal safer that wide brush offered by the Norton Online link, which wipes everything remotely suspect.

    After reinstalling Norton Internet Security 2012 from the CD, everything works as it should, including the fingerprint reader.

  • Canvio Basic 2 TB suddenly stopped working after Xbox update?

    While to say that the title of the hard drive has stopped working once an update has taken place on the Xbox one a few days ago.

    Now I tried it on a different Xbox one (didn't read), and also tried on a computer laptop windows 10 has yet no chance, at first he tried to install it but only got up then stopped, but even after having passed, still nothing, now its there if I go to device management (depending on whether its fine) but I can not even open the hard drive itself.

    I've had it for about 6 months maybe a little more, but still is it safe, placed just behind the xbox connected, never needed to move it.

    I hope someone can help or suggest something, but im now puzzled.

    Thanks in advance.

    I have the exact same problem mate

  • Capacity wireless suddenly stopped working after an update of Windows Vista.

    Feature WiFi suddenly stopped working after a windows vista updated.  Wireless switch is engaged, but stays yellow that messeges troubleshooting all say computer does not detect wireless devices.  It's as if someone pulled the unit and the antenna of the portable computer.  I also downloaded the wireless drivers and Setup several times without success.  Wireless device appears in the Device Manager page.  The only thing that is showing and work is the cable which is how I can download the drivers and appear on this forum.  Is it possible that the wireless device is broken?  All applicable lights are lit on the networking modem, no signal is detected on the computer, I have concluded that the wireless on the laptop is just inop.  Either way, I have a Compaq Presario F700 laptop.  All the options out there?  Thank you

    original title: can't find the wireless device

    Hello again, Kathy,

    More specific instruction, I can give to check settings in the BIOS of your system is to search for a list of devices that installed your laptop. There are only two options for each device, activate them and deactivate them.
    Look for something listed as network radio or wireless card and make sure that it is set to enable.
    The option that you network adapter found can also control the wireless adapter, but it can control only the plug adapter (Ethernet) network.
    A simpler solution, if you have not already tried it it is the system restore in Windows as mentioned by Kiran in a previous answer:
    WARNING: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can resolved e. Changes to settings are at your own risk.
  • My HP Envy touch screen has stopped working after an update of the HP Bios yesterday

    Can someone tell me please how to fix my touch screen. I got an HP BIOS update which caused my touch screen to stop working. I tried to re - calibrate the it, but it does not accept my contact telling me that the screen is no longer enabled.

    I tried to find where to turn them on and couldn't find where to enable touch of the finger. I also tried looking for driver updates and driver seems to be up-to-date.

    Thank you

    I have another type of TouchSmart, but this may work for you:

    1. Press Windows + X logo (if you are using a Windows computer 8 - If Windows 7, click the Start button, type Device Manager and click on Device Manager in the results of research).
    2. Select Device Manager from the list.
    3. Click on the small arrow next to Interface devices to expand the list.
    4. Click the touchscreen driver (in my case, Voltron NextWindow touch screen).
    5. Right click and select Activate from the list.
    6. Click Yes if a dialog box asks if you are sure you want to activate the touch screen driver.

    On some models, it is unclear which device in the checklist of the touch screen. I read in other posts that some people have solved the problem by disabling and then re-enabling each device.

    If this does not work, you could try to go to hp.com (http://www8.hp.com/us/en/support-drivers.html) and click on driver downloads &.
    In the search field, enter your product name or number, and then click OK. Select your operating system from the drop down list under Select your operating system, and then click Next. If there is no graphic driver available under Select a download below, click on the plus sign next to the driver - graphics, and then click the name of the driver. In the information and download options window, click Download. Follow the instructions on the screen to download the driver. Restart the computer.

  • "Show my windows and tabs from last time ' has stopped working after software updated to the end of January or early February. Now on 12.0a2. Change options "Auora to start: ' no longer works.

    I use this feature for years and update Firefox/Aurora in the next few days, maybe a week, an update becomes available and everything suddenly ' show my windows and tabs from last time ' has stopped working. I can go to the Tools-Option-general tab and change "at Aurora startup:" to this option, or 'Show my home page (s)' and now the opening in a new tab single even though I have URLs there. This may mean that this bit is not read correctly. I'm not playing: config, but I watch a few spoken options in the Web and everything looked OK.

    I would uninstall and reinstall it if you think it will solve the problem. I updated Aurora again because this problem started and it remains broken. It is a system of XP with SP3

    PS: I have two other windows with a XP and the other Windows 7. When I had the problem on my primary XP System I stopped to make updates to other systems. Today I updated the two other systems with the latest Auora (skip one or two updates) and both work very well.

    The best way for me to trouble?

    Hey punchcard4rjw,

    Have you tried to start Firefox in Mode safe? Key 'shift' startup of Firefox. If it doesn't happen in Mode without failure, you should read the extensions, themes and problems of hardware acceleration to resolve common troubleshooting Firefox problems.

    If this does not work, you should look the article How to fix preferences that will not save.

    Hope this helps!

  • The mouse scroll wheel stopped working after windows updates

    I have a Targus optical mouse with a scroll wheel; and he recently worked like this: when you use the scroll wheel in multiple windows, it would scroll the window (to move the vertical scroll bar) goes up and down.  It was a huge time saver, and I was used to it.

    I installed recently a whole bunch of patches from microsoft, including Windows 7 SP1 and Microsoft Mouse and keyboard Center.  The device is not listed in the center of the keyboard and mouse MS, but there is always a control-> mouse Panel.

    In Control Panel-> mouse, it has still the tab saying "wheel" roll the mouse to a notch wheel to scroll the rows x number of rows (it is selectable, I had 3, but tried to change as well); but it no longer works.  Now, it seems, I have to press the wheel to click, which then shows a circular scroll up/down, icon, and then I physically move the mouse up and down, and if I push down to click again on the wheel, I'm back to a regular movement of the mouse pointer.  It's MUCH more inefficient than the use of the wheel, so I'll try to figure out how I can get the drive working again.

    Should I uninstall MS Mouse and keyboard Center?  I thought about uninstalling and reinstalling the driver; but there is no mouse listed in the Device Manager (only has my touchpad there...)  It's a Targus optical mouse amu10usz; and even once, it was working fine before the installation of upgrades...

    Thanks for any help,
    A.J.

    Hello

    What is the number and the model of the computer?

    I will suggest you to check the mouse with different USB port or another computer, still question remains the same! Follow the mentioned methods:

    Method 1:

    Step 1:

    Update driver mouse

    a. click on start.

    b. click on Panel.

    c. using the drop down next to the opinion of: in the upper right, select large icons.

    d. click on mouse.

    e. click on hardware tab, click the Properties button.

    f. click on the driver tab, click set to update driver.

    Step 2:

    Uninstall the recent update and look for the question. You can first of all uninstall the update MS Mouse and keyboard Center and check.

    http://Windows.Microsoft.com/en-us/Windows7/remove-an-update

    Method 2:

    Hardware devices do not work or are not detected in Windows

    http://support.Microsoft.com/mats/hardware_device_problems/en-us

    Method 3:

    The problems with the mouse button or scroll the parameters

    http://support.Microsoft.com/kb/303091

    I hope that helps!

  • X 500 - 10W QOSMIO webcam stop working after Windows updates

    Hello.

    I have a Toshiba QOSMIO X 500 - 10W PQX33E-00R00CIT.

    When I format my laptop and you reinstall the operating system Windows 7 Ultimate 64 bit, the webcam works perfectly.
    After I updated windows via windows update webcam stops working. Also with Windows 10 company LTSB. What should I do? Thank you.

    P. S.
    According to me, is just a problem of software, not hardware. The webcam works perfectly until I do the windows updates! ' * ' Microsoft!

    I find the problem. Do not install the latest version of Microsoft Silverlight. I hope that I formatted my computer for the last time!

  • Outlook 2010 has stopped working after Windows updates

    November 11, 2015, my desktop, operating system Windows 7, installed about 28 updates to Windows. When I then put running the computer and open Microsoft Outlook 2010, Outlook closed almost immediately and this message appeared: "Microsoft Outlook has stopped working. A problem caused the blocking of the program works correctly. Windows will close the program and notify you if a solution is available. "(I don't check other office software).

    After the problem with Outlook 2010, I rebooted the computer several times and each time has experienced the same problem with Outlook 2010.

    I used system restore to restore the system to before the updates of Windows, which included a critical update. Outlook, then worked correctly. I changed the settings for Windows Update to "Never check updates" so that Outlook is not yet damaged.

    Was it something wrong with the Windows updates?

    The problem was solved when Microsoft released a revised version of the KB3097877 update. Maxwell Joseph, moderator of the Forum Microsoft, announced this in the post, he created at 23:22:03 on November 12, 2015, on the thread titled "update KB3097877 crash.

    He said ' Microsoft has released a revised update, so we suggest you go ahead and uninstall Windows updates KB3097877 > installed updates. Restart the system and run the updates check and reinstall it back. »

  • < Fn > keys stopped working after XP updates

    I have XP Home Edition sp3. I was invited for 6 updates for XP. After installation and restarting in now my keys on laptop are not working. None of them work. Other combinations of keys are OK. + C, etc are OK. Is there a way to remove the updates that have been installed?

    The laptop manufacturers implement the Fn key by using different techniques.  The first thing to do is to go to the website of the manufacturer of your laptop and download and install the driver of current keyboard for your computer.

    Still problems?  Post back with the brand and model of your computer.

    FYI, you can always go to windows update and click on the link to 'Review your update history'.  You will be able to identify the specific updates that have been installed.  Post their KB numbers here if you do not understand them.

    For diagnostic purposes, you can uninstall more updates by going to control panel > add or remove programs and by checking the box at the top to 'See the updates'.  In general, however, it is not a good idea to leave uninstalled patches 'critical'.

  • USB mouse stopped working after system update

    I'm running Windows 8 here and it updates automatic system has run and disabled use my connected USB mouse (manufacturer: Targus | model: AMU4201EUK)

    When I search the drivers in Device Manager tells me I'm using the latest drivers available and can't seem to find a driver for this specific mouse online.

    I use an external keyboard connected via USB and works without problem so I'm lost as to why the mouse would stop working. He able to go to the mouse as the LED inside turns on when it is plugged. Windows made his usual sounds when its connected and disconnected from.

    This happened last week and to work around, I restored windows since the eve of the update and it worked without problem. Windows tries to install the updates again after a few days, then the mouse will become unusable. I've lost the ability to return to this State, now I'm sure that Windows has replaced something in this update.

    The mouse uses of Microsofts HID drivers that are up to date and I confirmed the mouse works on other systems and on my laptop USB ports are functioning normally.

    Any suggestion is appreciated.

    See this similar post semi for some additional options open to you.

    After update, windows 8 pro will not be closed or sleep with connect to internet
    http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_update/after-update-Windows-8-Pro-wont-shut-down-or-sleep/24bdbd5a-AEEE-4ADB-B470-7ef5685acb99

    Have you had a look in Device Manager for errors with USB devices?

    Use the Device Manager and uninstall the concentrators root USB and devices which show now on your machine.  Restart and let XP rediscover and see if that solves your problem.

    If you uninstall the mouse in Device Manager, then reboot, Windows should find the mouse and install the appropriate drivers.

    Uninstall or reinstall a device
    http://TechNet.Microsoft.com/en-us/library/cc725782.aspx

  • ACR stop working after software update for Radeon

    I have a card Radeon R9 270 and CC Phoshop/Lightroom.  Everything worked very well. Then, I received a software update from ATI and accepted the installation to version 015.041.000.000. When I opened PhotoshopCC, a pop-up said that I had to enable GPU for ACR. I checked the box and opened a RAW file. ACR window open and I clicked the Open button. He locks up Photoshop. I had to stop the PS with the Task Manager. When I opened LightroomCC, the GPU box has been checked if I tried to use it. the first image open, but when I tried to click on another image, it froze and I had to close it with the Task Manager. I then disabled GPU in PS and it works fine. Given that Lightroom is just a front end for the cab, the develop module will not work and lightroom just freezes.

    I asked s ATI of instructions on how to revert to the prior software, but have not heard of them. I can not so much through the Device Manager because the revert button is grayed out.

    A quick search returns: Lightroom CC crashes after updating the Radeon driver

Maybe you are looking for

  • In the Google search box cursor flashes but is not enabled

    I asked this question on the Google forum but has been done on Mozilla forum. I know that I'm not the only one having this problem, but I've not seen a solution. I don't have any installed extensions. I do not understand how a slider can appear activ

  • Anyone not really 'pleased' with their Turbo?

    First of all, I don't want to turn this into an anti-Turbo or a negative wire. I'm curious is that I can't say I'm really pleased and I wonder if there are others. I've lived a lot of phones from the G1, Droid, Droid X, 2, incredible, S3, S4, M8, Mot

  • I can't get the videos to play on Windows XP. They say that I need codecs to play.

    I can't have a single video to play on my Windows XP Machine! They all say that I don't have the codecs to play! I have installed Klite Codec pack awhile back, but recently the codecs will not work! I tried to reinstall Klite Codec Pack, always the s

  • Wireless printer will not print from laptop

    Until yesterday, I was able to print from the desktop and laptop.  My printer is a HPC310 all-in-one.  I can print of the desktop but not the laptop.  Laptop is Windows 7 professional 64-bit.  When I click on the printer on my laptop it shows 5 items

  • Becoming audio unsync with animation unchecking after "continue playing project."

    Hello.When I add a link to another page (open in New) and uncheck the 'keep playing project', audio, I added is not a break with the rest of the slide. This creates a confusing delay between animation and sound, where the user does not know that the