HP ENVY 700-339-video bad HDMI on the Second monitor

In a Setup dual monitor a Samsung T240 and a Samsung T240HD the HDMI output a very poor text quality monitors.  The DVI quality is excellent. I changed the DVI and HDMI between the two monitors and the poor quality of HDMI is obvious on a monitor. HP has fixed the computer and replaced the AND R7 240 video card but the problem persists.

HDMI output and DVI with these monitors went well with my old HP Pavilion Elite PC m9150f.

Any ideas or suggestions would be greatly appreciated?

I have an older video card that supports dual monitor output, should I try it?

Someone at - it already update the video card in their 700-339 and can make recommendations on what works? If I receive information on the card and power supply, if it was upgragded so?

SGPatterson, welcome to the forum.

Here is a video card that works in your computer.  It requires only a power supply (PSU) with 300W.  It does not require an additional power connector.  There is a video for you to look directly below the map on the page.

You can try your old video card if it will work with your power supply.  It should not cause problems if it works with the UEFI Firmware in the motherboard.

Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

Tags: HP Desktops

Similar Questions

  • Win 8/IE 10: video Flash in mode full screen in dual monitor; video freezes on the second monitor

    All,

    At the launch of a Flash video in full screen when you are using two monitors, the video freezes at a still image on the second monitor. This happens in mirror and screen extended mode images.  The video continues to play normally on the first screen, and the audio continues normally as well.  This problem appears only during playback of the video using Internet Explorer, do not not Firefox.

    This seems to be a software problem, not memory or devices.  To be clear, the video is not stutter. rather, it freezes at a still image. I didn't have this problem using internet explore with the same configuration until I upgraded my laptop Windows 8.

    Here is my configuration:

    Windows 8. Internet Explore 10.

    Shockwave Flash Object: 11.6.602.167

    ASUS laptop computer connected to a HD LED TV via HDMI.

    GeForce GT650M graphics card.

    Core i7 and 8 GB of RAM.

    You think, what is happening? Troubleshooting ideas? Thank you.

    I just gave it a try on my setup triple monitor, but could not reproduce the problem.  I tried both stretching and duplicate the work stations, but they all work as expected.  If Firefox works well, then I wouldn't suspect your video driver but it is probably useful to take a look without worrying to do of course, you have the latest driver installed.  Then, try to temporarily disable hardware acceleration to see if that makes a difference.

    How to disable or enable hardware acceleration?

    http://support.Microsoft.com/kb/2528233

    Using IE in desktop mode or modern/metro?

    Thank you

    Chris

  • Video HTML5 will not be full screen on the second monitor?

    While playing a Html5 video full screen on my second monitor, whenever I try to do anything else the video mode full-screen. Video Flash works very well and will stay full screen on my second monitor. I also tried the same Html5 video in Google chrome and worked correctly and remained full screen too. So why the Html5 video will not remain on a second monitor fullscreen in Firefox?

    There is a fix for this, but apparently it is not yet available in the current version of Firefox (12.0). At the next update of Firefox comes out, you will be able to go to about: config and game "full-screen - api .exit-on-disable" false and the problem will be solved.

    I hope Mozilla will soon that the default for users will not do this!

    https://Bugzilla.Mozilla.org/show_bug.cgi?id=724554

  • Envy touchsmart 15t j100 - unable to connect to second monitor

    Hi, my problem is that, for some reason, my desire to hp cannot detect the external monitor. I tried to re - install the graphics drivers (hd 4600 / Geforce 740 m) and I tried to read and search sulutions in line but nothing helepd.

    It used to work and suddenly collapsed. any help? My only assumption is that the HDMI itself does not work.

    Thank you, Ron.

    Thank you for your answer!

    So finally, problem solved!  I found that when I disable the HD 4600 driver and only allow it, for some reason, that it works and my computer detects the second monitor, if I restart my computer or unplug the HDMI cable I have to toggle thing again... but at least it works!

  • No video on the second monitor (DLP projector) in PowerPoint 2003 presentation mode.

    When you use PowerPoint 2003 in presenter view, videos will not play on the second monitor which is a DLP projector. Video plays and produces the sound, but no picture. Videos play fine in clone mode. Using Dell Latitude D820 and windows XP pro

    For questions of PowerPoint:

     

    http://answers.Microsoft.com/en-us/Office/default.aspx

    Office at the above link forums

    http://answers.Microsoft.com/en-AU/Office/default.aspx?tab=2#tab=5

    PowerPoint Help Forums at the link above.

    They will help you with your questions PowerPoint when repost you in the Office Forums above.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    XP forums:

    http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

    Link above is for XP Forums.

    There is a list of the different Forums XP to the link above to help you.

    You get the help you need there.

    Here is the Vista Forums.

    See you soon

    Mick Murphy - Microsoft partner

  • HP Envy 700-147c: video and audio editing

    I have a desktop HP Envy 700 - 147c with Radeon HD 8670 D video card. When I'm editing video or sound, bogs, slowing and sometimes even crashes my software. I have a HP w2207h monitor. I have two questions.

    (1) is there a more powerful video card that I can just pop to replace the current card?

    (2) should I buy a new desktop computer, and if so, what would you recommend for audio and video editing?

    Thank you!

    Shawn Rosvold

    rosweed_1 wrote:

    I have a desktop HP Envy 700 - 147c with Radeon HD 8670 D video card. When I'm editing video or sound, bogs, slowing and sometimes even crashes my software. I have a HP w2207h monitor. I have two questions.

    (1) is there a more powerful video card that I can just pop to replace the current card?  The first thing you should do is upgrade the power supply (PSU).  The current PSU is only 300W.  Most newer cards require a minimum is 400W to work properly.  I recommend at least 500W to give you extra power for peak needs.  I love Corsair products.  As for a video card, here's a card which should give you more power.  I suggest you read the reviews to see what users have to say about it.

    (2) should I buy a new desktop computer, and if so, what would you recommend for audio and video editing?  If you decide to buy a new computer, the new gaming PC are great.  Here are a few examples.  One of them as displayed will be much more powerful than your existing computer.  You can configure all that you need.

    Thank you!

    Shawn Rosvold

    Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

  • HP Envy 700-200z: video card for want 700-200z

    Hello, I want to add a video card to my desktop 700-200z envy, which came with a single integrated graphics card. This is for video editing, and I just need a card modestly price such as the NVIDIA GeForce GT720, as long as it has open CL or CUDA. The GT720 will work with my motherboard? Thank you.

    Hi George,.

    The NVIDIA 720 is a video card very low end.  You might be better to use the NVIDIA GT 730 for $79.

    Review of the HP articles below.

    HP Secure Boot Windows 8 themes Computer does not start after the installation of a video (Windows 8) card  

  • How to configure to install HP ENVY 700 - 210xt video car EVGA 650 it boost


    Hello:

    Please read the guide on the link below for what settings BIOS need to be changed when you install a video card no HP in a PC in Windows 8.

    http://support.HP.com/us-en/document/c03653200

  • PC HP ENVY 700 series: How do I enter the BIOS settings

    How can I access the BIOS on this computer settings?

    Hello

    Start typing the ESC key after turning on the PC.

    Another option is to enter: change of advanced boot options on the start screen.

    You can also check out this other method.

  • Qosmio X 305-bad image on the external monitor quality

    My x 305-701 has excellent image on the original monitor, but if I connect the laptop to Acer 22 ' VGA cable I get a blurry image on the external monitor only.

    It does not matter if I use two monitors at the same time or just the Acer, the external monitor is always blurred the laptop monitor is always perfect. I tried the external monitor in 1440 x 900 and 1680 x 1050 and have adjusted the frequency of refresh of all available parameters, 59 Hz, 60 Hz and 75 Hz, and the blurred image is still there.

    I love this Qosmio and appreciate it even more on the widescreen monitor any help would be greatly appreciated.

    I know that LCD screens are blurry if set to non-native resolution. I think you need to set the correct resolution for the external monitor. Check your external display native resolution and set in display settings.

  • HP Envy 17 n065na: where should I install the second hard drive (Slot m2) on a HP Envy na065na? Photo inside

    Hello

    I'm planning on ordering a new SSD to insert as secondary on this laptop. According to the manual of the unit, it has an SSD Slot for m2 but I couldn't identify it the first time I opened. However, I have a picture that I hope where in the Board of Directors is the m2 for the SSD connector?

    Second question is, if this SSD would be comparible (model m2) to my laptop? If this is not the case, can someone point me to one between 256 / 512GB?

    http://www.eBay.co.UK/ITM/Toshiba-HG5D-series-512GB-M-2-solid-state-drive-/111763187434?hash=item1a0...

    Thanks in advance

    Photo attached.

    Now, I see the right slot. Not sure how I missed it. I only did you link to the manual, which is what would a HP technician if you could talk to one. The image of the motherboard in the manual is not correct. You're right, it is just a user to and sometimes they go wrong. Of course, my post was not the solution, but it's not as if they pay me for solutions. You can always go back and cancel a solution you gave and you should be if understand you more late it isn't fair. Again, sorry.

  • 17 3200 envy: Envy 17 3200 screen flickers and dies. External monitor works. (Video included)

    Hi, I bought my laptop about two years ago. A few days ago the screen suddenly dies, and at startup, it flashes several times with the correct display, but then turns off. The backlight seems to stay on. When I use an external monitor with HDMI port, the external monitor works fine, however, the laptop screen remains empty. Here's a video of what it looks like when I first boot the laptop: https://www.youtube.com/watch?v=mmro4P1NmyY & feature = youtu.be , how can I do to fix this problem? Thanks, Wes

    @Saichotic ,

    Hello and thanks for the display on the HP support forum.  It is somewhat a problem when it comes to laptops that comes up from time to time.

    The reason is there is a cable connected to the motherboard that goes back through the hinge area and connects to an inverter that powers the monitor.

    Once the cable wears out, but more often just to move General around get you a loos to the inverter or the motherboard connection.

    Here is a link to your Maintenance and service guide. You can use this to help pull the cable and inspect the connections.

    Maintenance and Service Guide

    Here is a video that will show you how essentially happen to things as well to test and check the cable.

    The HP Envy 17 laptop computer screen replacement procedure

    Now, if it of a little too difficult to manage, and believe me it took me a couple years before that I liked working on laptops is not a problem.  Contact HP support by phone for repair options.

    Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

    Thanks for posting and have a great day.

  • Desktop HP ENVY 700: problems with the boot from usb in the bios

    Hi I'm trying to boot from usb on a desktop HP ENVY 700. I don't know the serial number now.

    I followed the instructions and have produced a bootable USB and I checked this on a work dell computer where there is an option for me to boot from my USB if I so wish, but on my HP ENVY any options choose it does not appear with my USB in question and when I try to change the boot sequence making sure the usb/floppy and drive hard usb is above the rest of the sequencers starting it always starts just to the top as usual to my windows boot 10. I've disabled secure boot and used the boot of the legacy and it still does not work.

    I went through all the options I can that seem to be logic and it just does not work. I don't understand and I have to start using a usb key that I use the operating system can be very dangerous in a real environment, so it can not be downloaded to the hard drive.

    I need immediate help, this becomes quite frustrating now that it should be simple to do, but HP is not the way to simplisitic to do.

    Please if someone could point me in the right direction I would be so appreciative ideally if I could have a ride on the way to do

    I need this to work because I can't afford to buy new systems and its for my studies so its imperative

    Your PC has a motherboard of Memphis and happens to have a UEFI BIOS and the hard drive of the GPT format.

    You can check the type of hard disk online order volume by using the DiskPart utility.

    Create a flashdrive bootable UEFI with RUFUS.

    https://Rufus.AKEO.IE/

    Plug it into an available usb port before you press the power button. Near the powr button and immediately start to tap the F9 key to enter the boot from the sources menu. Select the Flash drive under the UEFI Boot sources. Let the boot process. If you have created the key correctly, it should start.

  • Two questions on the HP Envy 700-230ea before you buy

    I am looking to buy a HP Envy 700-230ea of PC World.  The plug that I saw didn't quite answer two questions that I have to solve before committing myself.

    1. the operating system is Windows 8.1 installed the 64 bit version (I need it to be)

    2. the machine is supplied with a 2 TB HARD drive.  But I need to add a second 2 TB HDD.  Is it possible to do it in the machine?

    On your HP UK Site, I would say that it comes with 8.1 / 64 bit and it has 3 internal hard drive bays; 2 external optical drive bays.

    Link http://www8.hp.com/uk/en/products/desktops/product-detail.html?oid=6753464#! % 3Dspecs tab

    Be forewarned of desktop computers HP ENVY do not come with a manual, just quick pictorial international owners set up guides, and there are no available records. The Windows 8.1 operating system can control, but for the computer itself no manual, it's like buying a new car, try to understand all the switches, levers and lights. Most are easy to understand, but some are not but I would like to contact PC World and make sure he has the 64 bit OS.

    Link http://www8.hp.com/uk/en/products/desktops/product-detail.html?oid=6753464#! % 3Dspecs tab

  • HP Envy 700

    It is possible to start and quit an application runs on a Windows 8.1 HP Envy 700 without a keyboard and a mouse and monitor?

    Hi struhsr, it depends, if the app doesn't need to keyboard and mouse to start that you can do, just run the application and then carefully unplug the mouse, the keyboard and the monitor.

Maybe you are looking for

  • imaqRotate2 fails with 1600 x 1200 pictures

    IM, rotating images of size 1600 x 1200, after only 20 runs, it fails and the corruption of memory occurs. Help please. Armando

  • My laptop computer and printer do not communicate with each other.

    I went to "printers and devices in the control panel and my laptop has an icon of troubleshooting beside him. I tried to search for updates/drivers solve the problem and nothing works.  It says ' unknown device is not a driver. My fax, copier and sca

  • HP 2000-2b43dx

    I'm not exactly computer savvy, so I hope someone can help. I bought a hp2000 a year and half ago. I don't know if this model is supposed to turn on with just the adapter or not. If so, then it is not. It turns on only with the battery. Also, I recen

  • WRVS4400N ASA 5540 L2L IPSec connection

    I have a remote WRVS4400N with a dynamic outside the address that opens a connection to an ASA 5540 with a static address. I'm all set on the side of the ASA.  My questions concern the 4400N.  It does not seem to have a very robust configuration/conf

  • Reconcile Smartphone blackBerry 8330/Outlook 2007

    I read a few post, but I can't find a definitive answer.  I am running DM 4.7 with outlook 2007, with BIS.  Can I wireless reconcile? If Yes please provide instructions Thanks in advance. DaNobleSquare