HP ENVY 750-177c: I have a HP ENVY 750-177c and has been upgraded and 2 thin black wires were disconnected.

I have a HP ENVY 750-177c and has been upgraded and 2 thin black wires were disconnected from the motherboard.  They have loops at the end of the wires that look like they might slip on the pins.  The wires connect to the upper part of the box of the computer.  Where to reconnect?

Find this card in your system. It is the M2 half-bridge Wireless card.  The other end of the wires must always be fixed.  There are 2 heels left and right of the '2 '.  If everything is correct, it is your physical WI - FI antenna. Just re - stick inside the case.  The small clips are used for an external aerial connection.

PS<> have a good day...

Tags: HP Desktops

Similar Questions

  • How can I fix it? "Money cannot connect to the store purchases.   If you have any firewall software, make sure it has been set to allow communication on port 443.

    This message p [ops upward when I run iTunes]

    Money cannot connect to the store purchases.

    If you have any firewall software, make sure it has been set to allow communication on port 443.

    How can I fix it?

    me too... same problem... just started

    iTunes can't connect to the store purchases.

    If you have any firewall software, make sure it has been set to allow communication on port 443.

    MacBook Pro, osx el cap 10.11.1, itunes 12.3.1.23

  • HP psc 750 color, which has been filled, cartridge will not print.

    HP psc 750 color, which has been filled, cartridge will not print.  Using Windows Vista.  Get the message "check color cartridge".  Only change to the system was making filled the color cartridge.

    Performing the procedure online electrical contacts cleaning service twice without a bit of luck.

    Looking for suggestions as to how to solve.

    Hello. Since the hard reset is not; I would try a new cartridge at this point. The hard reset is one of the most powerful tools when it comes to correcting hardware related problems and error messages.

  • Error iTunes - iTunes could not connect to the store purchases - if you have any firewall software, make sure it has been set to allow communication on port 443.

    My itunes has been fine. All of a sudden today it now gives me this error: error Itunes - iTunes could not connect to the store purchases - if you have a software firewall, make sure that it has been set to allow communication on port 443.

    I do not have my firewall active. I connected to itunes, quit itunes, reconnected - still a problem.

    Was there an update and now it's a bug? Help!

    Thank you!

    Run the Console application in one of the following ways:

    ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

    ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

    ☞ Open LaunchPad and start typing the name.

    The title of the Console window should be all Messages. If it isn't, select

    SYSTEM LOG QUERIES ▹ all Messages

    in the list of logs on the left. If you don't see this list, select

    List of newspapers seen ▹ display

    in the menu at the top of the screen bar.

    Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

    The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

    Please don't dump blindly thousands of lines in the journal in this discussion.

    Please do not post screenshots of log messages - text poster.

    Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

    When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

    If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

  • HP Envy 4500 series: printers has been removed

    Help, please! I accidentally reset my settings to the printer when you try to restart my printer because it was frozen. I tried to reinstall the printer several times but failed. When I'm in the printers option in my settings, I tried clicking on the button "+" to add my printer, but have been unable to get it to connect. It is completely wireless and I can not get the printer to appear in any screen. When I got to my printer a few months ago, my computer basically put it all for me. No cables needed. I desperately need help my printer because I am a graduate student and need to print almost every day. Any help would be wonderful I've exhausted all possible ideas I have.

    Thank you!

    Hello @kkall,

    Welcome to the Forums of HP Support!

    I would like to help you today with the addition of your wireless HP ENVY 4500 e-all-in-one printer on your computer Mac OS X 10.10. I understand that everything has started when you accidentally reset your printer settings. Therefore, I will start by ensuring that your printer is always connected wireless. Once we determine if the printer is on the network and 'talk' wireless with your Mac, you should be able to (+) add your printer back in. Please follow the steps below.

    Step 1: Check of connectivity:

    1. On your printer, down arrow until see you Wireless
    2. Select OK in the wireless
    3. Select Wireless details and click OK
    4. Make a note of the IP address that appears
    5. On your Mac, open your internet browser
    6. In the address bar type the IP (omit for www.)
    7. Search this site
    • Opens a Web site for your printer: If means that your printer and your computer "speak" wireless. Please proceed to step 4 below.
    • If a Web site for your printer does not open: This means that your printer and your computer communicate wirelessly. This would result in your Mac not to 'see' the printer (+) Add again. In addition, If none displays IP address on the printer, which means that the printer is is more connected to your wireless network. Please follow the steps below.

    Step 2: Run the Setup wireless Assistant:

    1. On the front panel of your printer, down arrow for the Wireless option
    2. Click OK
    3. Select the wireless configuration wizard , and then click OK
    4. When you are prompted to choose your network name SSID
    5. Fill in your password (key) wireless. It is case sensitive.
    6. Once the wireless is connected successfully, check the IP address of the printer
    7. Now, on your Mac take the IP address and enter it in the address bar of your internet browser
    8. Search this site
    • If the Web site for your printer opens: The printer and the computer are now 'talk' wireless. Please proceed to step 4 below.
    • If the Web site for your printer does not open: The printer and the computer are not 'talk' wireless. Please proceed to the next step.

    Step 3: Powercycle network:

    1. Start by unplugging the power cable to your router
    2. Once your router is unplugged, turn your printer off
    3. Then, shut down your computer
    4. After 30 seconds to 1 minute, reconnect your router back in
    5. Then, turn on your printer
    6. Turn on the computer

    After a few minutes the internet connection will be back. On your computer to access a few sites test Web to verify that the internet is running correctly. Once the internet works again check again the IP address of your printer. Try to open the site on your Mac printers again using the printers IP address.

    Once you are able to open to the site of printers successfully, proceed to the next step.

    Step 4: Add your printer:

    1. click on the menu of Apple , then Preferences System.

    2. click on Print & Scan

    3. click on the plus sign , click Add a printer or a Scanner, click the name of your printer

    4. click on the area of use or with the help of Print and then select the name of your printer on the shortcut menu. Ensure that the driver HP Envy is.

    5. click Add to add the printer to the list.

    -Source

    Now that your printer is added, please try printing again.

    Please reply to this message with the result of your troubleshooting. Good luck!

  • doesn't have a HDD with Win7 OEM, which has been improved to win 10 - No Media - how to install the new SSD?

    Hi members of the community.

    One of my colleagues brought me his personal computer to the difficulty.  It's a phone of 2011 which has Win 7 pre installed on it (OEM with a recovery partition).  It has no support for the version of Win 7 and she never bothered with the creation of recovery media or to order the installation media, but since its purchase, it has upgraded to Win 8, then 8.1 and finally Win10.

    Problem, it is the disk HARD watch of major equipment failures and every time you start more errors appear that problems are cascade.  There is a recovery on the HARD drive partition, but windows has trouble starting, I fear that this recovery partition is useless, because we don't want the windows reinstalled on this faulty drive.

    Can any advise if there is a way to install a windows OS on windows versions, that it has improved or the original win7 OEM supplied with the laptop without the media and with a damaged HARD drive?

    The hard drive that is damaged is a 750 GB drive at 5400 RPM samsung - she bought a new 980 GB SSD sata III.  I have already confirmed the laptop can use Sata III - I have a true picture and was curious to know if I can clone the recovery partition (if its still viable) can I do it on the SSD and then force the recovery on the SSD drive?  or that violate the license for OEM?

    Any advice would be appreciated, because I'm used to using volume licenses and I am new to OEM preinstalled OS damaged.

    Thank you very much

    ENO.

    Because the system is currently registered and activated with 10 Windows, just download the Windows 10 edition which currently installed, and then perform a new installation.

    How to download official Windows 10 ISO files

    then

    How to: perform a clean installation of Windows 10

    If you are prompted to enter a key click, product do this later and 10 Windows wakes in the coming days.

  • Is it possible to recover hundreds of mails that have disappeared from my Inbox after it has been quarantined today by Norton Internet Security?

    I received an infected email this morning which resulted in Norton Internet Security quarantine inbox. All received emails are gone now from the Inbox (with the exception of two who apparently arrived just before the infected message).
    (1) is it possible to recover the E-mails lost without re-infection of the Inbox?
    (2) how can I avoid this happening again? Until today, the infected emails have simply removed by Norton Internet Security on arrival without all the previous messages being lost in the Inbox.
    I would be very grateful for help.

    you force Nortons of UN-setting in the file quarantine.
    Then, you create an exception for Norton analyzes the folders that contain your Thunderbird profile, so it is not repeated.

    Be aware that the infection is not as severe as the cure. Maybe you can find someone to Semantec to explain how an email in Thunderbird can infect anything unless you physically open an infected attachment that Norton should catch when it is written in the temp folder before opening.

    I lost a lot of time talking to corporate cretins to Semantec and they charge just "this is another line of defense" when asked for more details. Why, because they can simply justify not e-mail Scanner in any other terms. Enjoy it servers little or not by the challenges of usability and convenience.

    This "mail" was written on your drive hard until Semantec has managed to make a mess of things. It's a little late don't you think saying "you have an infection. Do they expect also for stuff in your browser to be written on the disc? You bet they do. Where is the preventive surveillance to data transmissions that prevents infection before it is written on your drive?

  • I have a disc of Adobe Illustrator10 program has been installed on my old computer. My new computer doesn't have a hard drive. How can I download the program?

    I have the disc and the product number. Is there a place on the Adobe site that would facilitate the download from the Illustrator 10 disc. I buy a zip drive? How can I get the program I already paid for years on my new computer with no disk drive.

    Please visit:http://www.adobe.com/downloads/other-downloads.html

    I hope this helps.

    Concerning

    Megha Rawat

  • I can't activate a VM XP, I have a VLK license but the machine has been built with an oem license.

    I can not activate a virtual XP machine.  the virtual machine is a clone of a pc that has since been erased.  the original machine was probably activated with an OEM key.  I tried activating by phone and putting our license key of Volume without success.

    I would be grateful for any suggestion.

    Thank you very much

    Heh!

    The key to the report is an OEM_SLP key, rather than a Volume key-

    The key of COA_SLP supplied with the original computer cannot be used to enable this virtual machine either, because he reuires to use on the original material.

    You can not use a license upgrade for the virtual machine, because there is no base license - so you are limited by the terms of the Windows license using a retail for Pro license, and then upgrade which (if necessary).

    The key here is most likely another valid - but installation is almost certainly classified as non-authentique, due to the presence of the multitude of the OEM.s in the BIOS - unless you use XP Mode in a Win7 machine

  • I have a new Pavilion of 2026 p6 has been put to the top of my email last night but made mistakes of inputing information.

    1 Pavilion P6-2026.  QX347AAR #ABA

    2 Windows 7 64 bit

    3

    4 new machine

    Please let me know the email client, that you tried to install. If it's Windows Live, please visit the following link:

    http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-mail-setting-up-an-account-from-start-to-finish

  • need for a disk recovery for my Dell Dimension 1100. When I got it it didn't have a drive with him. It has been formatted and now cannot operate

    I bought a friend who bought it from Dell.
    He reformatted it and now it has an error message Windows root \system 32\ hal.dll is missing or damaged.
    Please reinstall a copy of this file.
    It had Windows XP Home Edition
    The service tag # Reference Dell is8SG64B1
    Any help would be great

    Contact Dell, but are not very optimistic.

    Find an OEM version of Windows XP Home Edition (friend, family, co-worker, a friendly match, IT supports the person) and hope that you can always read the product key on the machine label.

    The case-, it would make a good Ubuntu machine.  ;-)

  • my files have disappeared when acrobat has been upgraded to acrobat dc [Android]

    Where are the documents I had stored in the old pre dc Acrobat?

    Ok. I got the update, it works fine. Thanksks

    Sent from my Verizon Wireless 4 G LTE smartphone

  • How is it, I can't use the editing tools when I'm using Adobe Acrobat Reader DC it wants to buy me now.  But when I use Adobe Acrobat Pro DC I have no problem using the mounting tool yet I had Marcus XI of Acrobat Pro, then it has been upgraded to such th

    I already pay a subscription for Adobe Acrobat Pro XI now he wants me to buy when using the tool change or even insert pages never had this problem before?

    Acrobat Reader cannot edit PDF files. Use Adobe Acrobat Pro DC.

  • Mini Mac 10.5.8 has been improved to 10.7, we have a lot of products older Apple if I buy the most recent delivered to nine Mini can I still use my iBook etc.

    My Mini Mac 10.5.8 has been upgraded to 10.7. We have a lot of Apple products. If I always buy a refurbished Mac Mini can I have limited access to my other computers laptops, iPhone, etc. I'll gather all the detailed information of the products Apple and posting here.

    Everything should be good. Just use the same identifier Apple you used on older devices.

    Note the following points:

    Upgrading to 10.7 and don't forget Rosetta!

    You can synchronize only with a computer. To move computers

    Synchronization to a 'New' computer or replacing a hard drive "crashed": Apple Support communities

    If all the media synchronized music and apps are already in the iTunes library of the new just backup on iTunes computer and restore from this backup.

    iOS: backup and restore your device iOS with iCloud or iTunes

  • How can we have a column with the text and radio button in the same row?

    Hello

    I have a column that need to have data with a radio button. Has been able to achieve this by using < trh:tableLayout >. But when I select the option button it moves to the next line. You want to stop this behavior of option button to move to the next line. This column also includes a hyperlink. If the text and the hyperlink are made invisible visible based on the action of the radio button.
    Adding one more doubt. A horizontalgrid of specific columns can make invisible?
    Any help would be appreciated.

    example code:
    < trh:cellFormat id = "cf8" halign = 'Start' >
    < af:activeOutputText value = "#{rank." Actions}"id ="aot2"/ >
    < af:goLink text = ' #{rank. " Actions}"id ="gl1 ".
    clientComponent = "true" visible = "false".
    targetFrame = "_blank" destination = "http:// + #{rank." BUTTON_URL} ">"
    < / af:goLink >
    < af:selectBooleanRadio text = "" id = "sbr1" > "
    < af:clientListener method = "selectCheckBox" type = "click on" / >
    < / af:selectBooleanRadio >
    < / trh:cellFormat >

    Thank you
    Nita

    Remove the components from . Put the other components like the direct children of the PanelGroupLayout:

    
      
        
        
        
        
          
        
      
    
    

    If you need to add some space between the components horizontan, you can put (s) between components.

    Dimitar

Maybe you are looking for

  • Search for devices wireless in Configfree

    I have a satellite M55-s135. Until today, when I would start or click on the prompt "find wireless devices" Configfree a virtual radar map will appear showing Wireless connects. This virtual map will not appear.When I click on "search for wireless...

  • Spare Ideapad Y410p not available on ebay or amazon?

    A few days back I saw some Lenovo Ideapad Y410P and Y510P included on amazon.com and ebay.com spare, but now I can't see these products. I have no why. Is it still available on amazon and ebay or not?

  • Upgrade Advisor omitted Windows 7 Professional

    Hello- I ran the Windows 7 Upgrade Advisor on a computer in Windows Vista Home Professional 32 - bit and the results noted the following: (check mark)  Upgrade Options available: you can switch to 32-bit Windows 7 Home Premium or Ultimate. Question:

  • Upgrade to windows windows 8.1 8

    I have a problem in the upgrade to 8.1 windows where it is not visible in the store MORE. Yes, and more, means it used to be visible, but after several updates is not visible any longer. Also, I installed all the updates, until there is nothing when

  • Transfer of creative cloud to a new computer

    I have creative cloud on my laptop, but I am trying to buy a MacBook, is it possible to transfer all of the creative cloud? Or is it a different installation on a Mac?