HP F4480: PRINTER F4480 WILL NOT POWER PAPER - TO NEAR EMPTY INK LEVEL

Hi, the book in my HP F4480 printer will not feed. The ink cartridges are nearly empty, if not empty. Weak cartridges prevent the printer from paper making to finish a job, or is it likely another question?

Hi @80Printer,.

Thank you for joining the HP Forums!

I have seen your post on how your HP Deskjet F4480 printer will not feed paper. I'm happy to help you!

Low ink cartridges can certainly be the cause of not feed paper. I recommend that you replace the ink first and see if that solves the problem. If it does not solve the problem, go through this guide, 'on paper' Error Message on the computer and the printer is not Pick Up or paper feedand let me know what happens!

Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

Hope this information is useful and thanks for posting!

Tags: HP Printers

Similar Questions

  • HP Officejet printer 4620 - will not power up / turn on

    My printer does not illuminate.  If I remove the plug from the socket turns on and turns off then on again.  The message on the display says "turn off the switch to avoid any damage", but that's what I do all the time.  He then turns off.

    Error message reads Oxc19a0013

    A person can offer advice please.

    It has ink should be in the printer, usually some back of small spatter and the capping station (basically a pad on the bottom of the printer in the right side). If you have what looks like the casting of ink in the printer, Yes, it could be the cause of the error.

    Did you try the update of the firmware, I suggested?

    It may be in your interest to contact HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 for all other regions, click here.

    Kind regards

  • PSC1510 .my printer is will minimize the paper.

    My printer is will minimize the paper.  He takes a sheet too far through reports about 3 inches and then a paper jam.  Erasing it has no effect. the same thing happens with the next sheet, etc.

    Follow the steps in the document located here for the procedure help fix and avoid future paper jams.

    If the steps do not end the question of setting, then you will need to consider alternative options. Have you thought about contacting HP Support on the upgrade program?

  • hp8550 will not feed paper

    My Hp 8550 stopped feding paper. What can cause this?

    my printer will not feed paper into the printer.  He just left.  What's wrong?

  • Workstation Dell Precision T7400 will not power with ATI Radeon 5970 installed

    Hello

    I had my dream, the monster bi - GPU ATI Radeon 5970 video card and installed in my T7400 but the system will not start, all I get is a fast fan rotation and a kind of sounds from food, a bit like "Brrrnt, click on" led me to believe that the power supply could not handle my video card.

    The video card requires an 8pin and 6-pin power plug. When I plug the 8-pin and 6-pin and turn on the computer, is a no-go as shown above. When only the power plug 6-pin I plugged the PC sounds like it will start, the power of fans but no display as I expect.

    I tried this video card into the two PCI-Express slots with the same failure as a result. The computer works fine with the Nvidia Quadro 3700 in it... using a 6 power connector pins.

    I got the ATI Radeon HD 5970 video card in a store of the local computer and it had tested ($15) because I didn't test it in a spare computer and video card passed with flying colors...

    That's why I thought my 1000 Watt power supply was a problem, so as a bet, I ordered a replacement off eBay and received a sweater to work more the wiring harness and completely replaced the two who has a job to say the least! Have you tried to replace the wire bundle? a lot of work...

    I got it all back together, crossed my fingers and prayed and tried again and the same thing... NO LUCK... I put the graphic card Nvidia Quadro 3700 back in and the system of power like a charm.

    What on earth could it be the cause for it? I REALLY want to get this video card works in this system.

    I even tried a bios update and carefully watched the card mother and everything that I could to see if there's... nothing exploded capacitors...

    Please HELP - I want to get my game...

    Wesley

    I think I found the solution and I would like to mention it here to help others if they get him...

    A: the power of Dell for the T7400 was designed to produce five rails 12 volts @ 18 AMPS each and the video card requires approximately 45 to 50 amps to work properly. Video cables (one with a 8 pin) and 6-pin on the harness even seems to only provide amps 18 or more and the computer will not power because power protection circuit sees too many amps being requested by a 'rail' and turns off immediately...

    I went to electronics of FRY in San Jose and bought a few cards that helped divide the current between different sources, such as the cables of the hard drive and video.

    B: I have a small battery backup power unit and my T7400 was plugged into the saved game... When I got the video card to work, he could make a beep loud and after minutes cutting my T7400 due to the mainstream power support... I plugged the computer into a 'surge protector' but not battery backed up to the slot and since then had no problems...

    Now after several tests including FurMark, my graphics card stress works very well in this system... This is due to an unfortunate design in the T7400 power supply and wiring... Now that I have this solved, I hope that someone else can benefit...

    Get an adapter like this one, it allows to separate the power sources for the 8 power connector pin and use the PIN 6 original which is connected to the Dell printer condition 8 pin adapter, for the 6-pin slot... hope that makes sense... by trial and error, you got it right!

    I had one like this:

  • HP Photosmart C310a will not power off no response on the screen is

    I have the HP Photosmart C310a months which will not power off or answer unless I have remove the power cable of the whole or to the back of the printer.  Using the Wi - Fi connection, so there is no usb to printer cables.

    This widget could not be displayed.
  • Satellite Pro A40 - will not power

    The laptop will not power, just a flashing yellow when the power connector is plugged?

    Hello

    Read here before you discuss your problem, please:

    http://APS2.toshiba-tro.de/KB0/FAQ6201DK0004R01.htm#

  • I tried to buy my book - DEFAULT TEXT - your book seems to have default text that has not been modified. Printed books will not include this text. This means all my text will not print?

    Using OSX El captain on a desktop iMac. iPhoto 9.6.1

    I tried to buy my book - this box appears - TEXT by DEFAULT - your book seems to have default text that has not been modified. Printed books will not include this text. Does this mean that all my text will not print?

    I've been twice now and change the text of Bradley Hand to the Blackboard to Helvetica Neue - which seemed to be the default. Message remains displayed. I don't know what else to do. This is my third book over the years, but the first with this problem. Can someone advise please?

    Thank you Davina

    It is not a problem of fonts. It is the problem of the sample text entered by the models.

    The error message means that there is a text field in your book which is still on show at the text included by the model, and you will need to replace this text with your text. This textfield might be hidden behind a picture.

    If you create a preview of the book, such default text is omitted. Have you compared the preview of what you see in iPhoto? Text that shows in iPhoto, but not in the preview will be such default text.

    For example, the section 'Topic of this book' on the flap back in some themes is a default text that should be replaced by your own legend:

  • Equium A60-157 will not power

    Hi people!

    Could someone offer a bit of expertise and tell me whether or not the series Equium A60 - 157 has a center pin in its socket? I need to know that my laptop doesn't have one and it will not power! I'm deeply frustrated because I paid at the time £999 and it doesn't work!

    I have a feeling that the PIN has cracked and is now part of my dc adapter but I need to be sure before I get it fixed!

    Also if this is the case anyone Kow how much it may cost to do fix an indicative maybe!

    Cheers for your help!

    Nick

    Hi Nick,

    Yes, I think the A60 use an outlet that has a central pin. The CAP at the end of the head of the AC must have a central hole. You can find that the spindle broke and is now stuck in the plug on the power cord. This is not a rare event on the series of satellites, laptops.

    The bad is more Servicers will simply replace the motherboard (where the socket is together) rather than perform a repair to the component level. It is obviously a costly option for you, but is probably more faster/easier for the repairman.

    I have, in the past, tried unsuccessfully to find a source for the plug for my A30 (just in case) but I only managed to find a supplier who could provide a component of second hand provided by a junk motherboard. :-(

    Kind regards

  • HP b209a printer range will not connect to router comcast using the WPS button

    HP b209a printer range will not connect to router comcast using the WPS button. I try to use a new Comcast router (technicolor TC8305C). When I try to connect the printer times out and says that no connections are when I check for wireless connections. Yet, when I print the network configuration page, the SSID for the new router is at the top of the list. I reinstalled the software by the support of Comcast, but it did not help.  I'm ideas please help!

    Thank you

    Never use WPS to connect.  If done it should be disabled in the router for security reasons.  Connect manually via the SSID and password following the instructions in the manual.

  • Photosmart Premium C309-g: the drivers and the printer software will not be installed.

    My network all-in-one Photosmart Premium C309-g worked very well on my desk until recently, when suddenly the HP software could still see and connect to the printer, but Windows 10 could not. I tried to remove the printer and uninstall all associated software, then tried to reinstall the software. Unfortunately, the installation will not get to the point where it starts and then suddenly disappears with no trace of her still running in the background. I can deviate from the default installation and bring to the top of the page to select the components that I want to install, but when I do the button 'ok' on this page does not work. No matter how many times I click on it, the page remains open and the installation will not so fast. If I click Cancel on this page, it disappears and the installation back to the previous page, where I can choose to continue and happen almost immediately out of sight again. This happens whenever I try to install selected software and drivers. I deleted the printer from the devices page in the Panel, I made sure to this it is not is more listed in the Manager of peripheral devices (printers and imaging devices), I removed the Windows 10 print queue and I deleted all the data of the folder under the Program Files (x 86) HP folder on my hard drive. I also disabled Windows Defender and run the installer as administrator, yet none of these steps help the process at all. I have never, in my 20 + years using nothing other than printers HP, encountered a problem like this. I'm used to receive error messages during the installation of software to fail, but I have never had a process simply disappear from the computer without leaving any trace of never having run. I hope that someone out there has an idea, that I have not thought yet, transferring files to my tablet to print from becomes a pain in the rear.

    A man who took the freedom of another man is a prisoner of hatred, he is locked behind bars of prejudices and narrow-mindedness. I am not truly free if I take freedom away from someone else, as surely as I am not free when my freedom is taken from me. The oppressed and the oppressor similar are stripped of their humanity.
    ~ Nelson Mandela

    Welcome to the HP Forums @GarfieldFan1969,

    I understand the printing software will not fully installed for your Photosmart C309 on your system Windows 10, and I wanted to answer with my suggestions for trying to help! Here are my suggestions for you to try. When you are finished, please let me know the results and problems or errors that you may encounter!

    First step: clean boot, restart the PC and try the install again.

    1. start by typing "msconfig" in the search box of Cortana, and then click MSConfig (run command)
    On your keyboard press Windows + R key at same time and type Msconfig in the run window, and then click OK or press ENTER.

    2. now, choose Selective startup

    3. Remove the check of the Load Startup items

    4. click on the Services tab

    5. check "hide all Microsoft Services" and then click on disable all

    6. click apply , then OK

    7 restart the PC and temporarily disable firewalls or antivirus programs

    8 run the Installation Wizard for Windows HP printer to install the printer

    9 turn on the firewall and start services

    Second step: you unregister and re-register the Windows Installer Service:

    1. hold down the Windows key + R to fill the box "Run" and type cmd.exe, and then click OK.
    2. at the command prompt, type msiexec /Unregister , and then press ENTER.
    3. at the command prompt, type msiexec/regserver, and then press ENTER.
    4. at the command prompt, type exit and press ENTER to close the command prompt.
    5. run the Wizard for Windows HP printer installation

    Step 3: run System File Checker Scan (up to 3 times) to repair the corrupted system files:
    1. go to start
    2. type CMD
    3 right-click and run as administrator
    4. to check and repair the OS type sfc/scannow (note the space between sfc and ' / ')

    You may need to run this upward to 3 times to solve all the problems

    When finished, it will say one of three things
    Windows did not find any breach of integrity (a good thing)
    Windows resource protection found corrupt files and repair the (good)
    Windows resource protection found corrupt files but was unable to fix some (or all) of them (not a good thing)

    Try to reinstall the printer.

    Step 4: activate the built-in Windows administrator account

    source

    1. first of all, you'll need to open an administrator mode command prompt by right-clicking and choosing "run as Administrator" (or use the shortcut Ctrl + Shift + Enter in the search box).

    Note that it works the same in all versions of Windows. It just search for cmd and then do a right-click on the icon of the command prompt in the start menu or the boot screen.

    2. If you are in Windows 8.x or 10 you can click on the Start button and choose to open a command prompt in this way.

    3. now type the following command:

    NET user administrator / Active: Yes

    4. you should see a message that the command completed successfully. Log out, and you will now see the administrator as a choice account.

    (Note that this screenshot is for Vista, but it works on Windows 7 and Windows 8 and Windows 10)

    You will notice that there is no password for this account, so if you want to leave it enabled, you must change the password.

    Try to reinstall the printer.

    Testify of my answer by hitting the thumbs to the top slot

    Click on the button "Accept as Solution" if I helped you reach a solution.

  • Try to reinstall the printer and will not install due to not having Admin rights

    original title: Instalation printer

    Try to reinstall the printer and will not install due to not having Admin rights. I am the administrator,

    How can I continue?

    Thank you

    Right click on the printer software setup.exe, etc > run as admin.

    See you soon.

    Mick Murphy - Microsoft partner

  • Photosmart B109a-m printer suddenly will not print.

    My Photosmart B109a-m printer suddenly will not print. It worked last night and no connections or settings have been affected since then.  It will not print the test page and the printer Utulity advises that means a problem with the printer, not the computer.  The computer shows it sends data to the printer and indicates that it is printing but nothing happens with the printer.  Any ideas how can I fix?  I'm on an iMac with Lion.

    How is the printer connected?

    Try to reset the printing system:

    -Go to System Preferences > print & Scan
    -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
    WARNING - This will remove ALL your printers!
    -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

  • laptop will not power. No blue light with ad adapter not plugged in.

    Lately, I've been jump the battery in and out to get the laptop (dv6) to propel to the top. This afternoon after a morning's work, the blue laptop ac adapter light does not illuminate and the laptop will not power.
    Naturally, I suspect the battery, but maybe it's the AC adapter. If all goes well, it is not the computer itself!

    Any ideas on what I should buy first. Am on business in Dubai and desperate!

    Thank you
    Jeff.

    Solved. Sort of.
    I bought a new battery and everything works as it should.
    The real question now is why stop a bad battery the notebook powered with the AC adapter is plugged?

  • Dell 1230c do not - print jobs go to the queue printing but will not come to buffer

    Dell 1230c do not - print jobs go to the queue printing but will not come to buffer

    Hey Joe,

    Try duration to remove print jobs to remove Job feel stuck in the queue, and then restart your computer.

    Also refer to:

    Cancel printing

    Maybe you have that impression break.

    View, pause, or cancel printing

    You can also see the troubleshooting steps in Dell for Dell printers.

    Please post back with the State of the question.

Maybe you are looking for

  • A9G89AV Actuall speed USB Ports

    Product # via BIOS = A9G89AV i5-3317u USB 3.0 ports are normally blue? Right? Does actually 2 USB 3.0 ports, and it was made until they begin their coding by blue color?Or are they really 2.0?One review said 2.0, another says 3.0.Thank you

  • Can't see the details - time and State of charge of battery

    my PC laptop battery charge and discharge ok but the icon in the taskbar can not tell me how cool.I left there just an empty battery that says remains unknown. Is there something wrong with my battery or is this a driver issue maybe?

  • Have an old iCloud ID trying to update an application

    The App Store tells me that I have to update an application.  When I click on update, it's invited me to an old, no longer in use iCloud ID (which I suppose than the one that I used when I first bought this app).  I don't remember the password for th

  • can I update my iphone 4

    Hello I have an iphone 4. Is it possible to update or I have to update my phone instead. Thank you.

  • Satellite L500-14F - where can I get the drivers?

    Hello everyone I really need drivers for Satellite L500-14F. I just bought it and I did a format for her, and then he asked me for the update of drivers. The shop gave me a CD for her. Is it just for this model without drivers CD if that's why they d