HP G61 511WM processor change?

I have a HP G61 511WM.

I'm looking to change my processor for portable computers such as in her shots of the moment. I want to know if it's possible and for

upgrade and getting tired of things.

So far, seems if they are in the same series, you can replace the processor to a better model. Which means that I would be able to replace my processor, as LONG as it is in a better version of my laptop. According to this article, I found, this guy did it and it worked, but his was a different model mine, just wanted to check with you guys to see if it will still be possible on my own.

http://h30434.www3.HP.com/T5/notebook-hardware/G61-306NR-CPU-upgrade/TD-p/239906 http://h30434.www3.HP.com/T5/notebook-hardware/G61-306NR-CPU-upgrade/TD-p/239906

Hello

Here is the list of processors supported (page 1-1)

http://h10032.www1.HP.com/CTG/manual/c01868653.PDF

not much choice.

Kind regards.

Tags: Notebooks

Similar Questions

  • HP G61-511WM computer laptop not high volume

    HP G61-511WM

    Windows 7

    On my laptop, I had a problem with my volume is not strong at all.  I turned the volume as loud as possible upwards, and yet the bluish green bar jumps only barely up and down when I play music or any type of sound.

    Megan

    Hello

    Click on the link below:

    Increase the volume of speakers low laptop w / Windows 7

  • Should I delete my temporary files on my computer hp g61-511wm never laptop?

    Should I delete the GCC on my computer hp g61-511wm never laptop?

    Hi Clevermonkey,

    Do you mean Internet Explorer or loading turn on the Windows computer? He continues running slowly after that that it has loaded up? Here is a link to try if the problem is Windows start slowly.

    Computer Windows is slow to start up:

    http://www.computerhope.com/issues/ch001131.htm

    There are a number of good steps in there to try. Let me know how it goes.

    What operating system do you use?

    Find your operating system:

    http://Windows.Microsoft.com/en-CA/Windows/which-operating-system

    Thank you

  • Installation SSD G61-511WM

    My friend has made my laptop, yes it's a laptop from Wal-Mart. He had no idea what was wrong with her, but he had removed the hard drive to replace a dead from another laptop. So, no hard drive. After tinkering around with it for quite some time I finally noticed what was wrong, fixed it, replaced a bad and vwalla ram chip. It worked.

    Now, I have a problem: the only hard drive I have around, the pose is an additional solid state drive I bought initially for my office. It is a luxury to Mushkin Callisto 40 GB. This laptop isn't exactly something to write home about, but I think it might be useful on occasion. He got HDMI after all, it is always an advantage. My elitebook doesn't even have that. :/

    Problem starts with the BIOS. It's the most basic BIOS I have ever had the misfortune to deal with. There are no real options to toggle, so naturally there is no AHCI option. I understand that it is your laptop model Wal-Mart, but seriously... it's all just ridiculous.

    Without AHCI option, I can't install windows 7 on ssd.

    Because I have no record of the NORMAL laptop, I can't install windows 7 to run the update bios .exe.

    I need a USB Flash bios update for this machine, or a workaround to get windows 7 to see what SSD.

    Thank you

    Jon

    Edit: Oh Jesus, this thing has a Toshiba motherboard? Hilarity!

    Managed to update the BIOS to 363 F.15
    Still no AHCI option.

    Used a bios whitelist.

    STILL no AHCI option.

    Curiosity, what is the point in releasing a BIOS if you can't DO something with it?

    I can say to make it start the laptop from the CD, and I can change the time. Whoopdie Doo.

    And. Always impossible to install an SSD
    Went through the SHIFT + F10 menu for windows 7, crossing in diskpart.

    Always impossible to use this player. It boils down to what is a bios problem, I'm sure.

    Thus, HP? I would actually use this equipment?

    Ok.

    Officially, this problem is solved.

    The solution is very simple:

    Have your friend the other tech guru are carefully watching the computer for 15 seconds. As if by magic, Windows detects the drive, includes what it is and loads.

  • Storage processor is passed to an unmanaged to an IP address change status.

    I have a CX200 and ip address on one of the storage processors changed that nobody will admit to and I need to be able to change it back. The student pilot was granted a status of unmanaged and I to talk about her problems. Is it remotely possible?


  • What type of processor do?

    I want to upgrade my processor in my computer, but I know not what type of mine is or what will work.

    It of an E-300 AMD, taken FT! BGA. Please help me thanks

    Hello

    The following link shows the full specs of your machine:

    http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=c03206025&lang=en&cc=us&TaskID=130&ContentType=SupportFAQ&prodSeriesId=5187034&prodTypeId=12454

    The CPU (processor) is a "AMD Fusion E300 (Zacate) Dual Core processor soldered to the motherboard" it means that if you want to change the processor change the motherboard.

    Kind regards.

  • Possible Hijack, System get "changed" or perhaps "partially virtualized" virus strange very important situation

    I have a problem with 2 computers and its kind of a large.  Hard to know where to start so I'll keep it short, but I think it may concern even Microsoft, because it involves the use of what I believe to be false "terms of service" or small print and I knew even where the source of this problem is, but I really need help! Myself and others use laptops we bought together.  We live in a family, but laptops, a TOSHIBA and a HP/COMPAQ F700 satellite, as well as what I call a wireless router belong to the USA! We are connected through this wireless device, a PRISM which is perhaps a bit older, but of course seems to work, it is plugged into a modem cable motorola belonging to someone else in the House.  To make things moving along, he came to our attention that A: our systems periodically change without our permission, by that I mean that the toshiba that was purchased at walmart brand new, came with an Intel Celeron, and I think THAT the wireless card IS an atheros brand.  I KNOW that was the case with the Compaq regarding the wireless adapter, and Compaq was bought at a rent to own store and came with a 1 GB ram AMD processor.  For some reason, we are under some form of control Admin, and our system is changing periodically on BOTH computers to say his family chipset intel and our wireless adapters will go to realtek USB 2.0, once again on BOTH computers.  When this happens, our user accounts admin, that we had as an administrator user accounts AND I have unlocked the hidden via the cmd prompt and hold SHIFT + ENTER thing, will be signed in some way limit our ability to do things.  LAST FEW DETAILS, I promise you: the so-called matrix memory of intel as magically appeared with software RAID of surveillance and we saw our event logs, which we prob didn't know existed, being transferred by a remote user, and we have never consulted the remote adjustment, except in order to turn them off, as well as file sharing options.  However they continue to change when this happens.  Yesterday, to finish that, I found strange things after doing a thing of complete system repair, not for the first time, this time on the compaq.  After the repair, which seemed fine at first, I was embarrassed to find a few shortcuts readme present in the recently amended on the start menu folder.  I followed them to the folder locations that led me to the prog. files, THE SIMS 2, and various subfolders with S.W.R. claiming to be from MICROSOFT and don't mention any particular O.S. except with reference to .NET and some virtualization programs that we noticed the menu running task.  OH, I shouldn't forget that with the processor changes in both pc, THEY BOTH now say that they ar x 86 client or PC workstation and a recent attempt on the repair of the system or pressing f8 on the toshiba somehow led me to a weird command prompt which began with X : ??  I'm prob a few things set aside even if it is really long, but the SIMS 2 folder is very disturbing because a person who lives here once gave us a CD on an old computer that has not been used for at least 3 years and we have certainly not installed this game WE NEITHER of these new computers.  I SUSPECT SOME things but don't know what to do.  I TRIED to get our product off the coast of the TOSHIBA key but was said previously by a repairman it seems to have BEEN DELETED!  The records in question, according to me, are always on both pc and we executed the software suggested, including microsoft security databases, s.s.and destroy, and the malewarebytes thing, as well as to have a repair shop gives us some tips. They said several things, like the toshiba tried to boot from the drive cd/DVD, then boot pxe or something and someone had changed the wake on lan option, and maybe other things I do not remember.  OK SORRY FOR ALL this THAT REALLY, but I wanted to make sure that I gave as much information as possible because we never wanted our PC clone, virtualized, or something like that, whatever realtek usb 2.0 is, it's another icon of the wireless connection in the tray on the lower right AND THE COMPAQ is REMAINED CONNECTED WITH the off switch wireless?  Help!

    Thank you for your gracious reply. It certainly sounds to me like your computers are compromised. As I said, the only way to fix now is to restore as long as the plant once more after you back up your data and then set them up by the suggestions below. It costs you nothing but time. I'll also give you my general information on the configuration of the network wireless safely. Unfortunately, you must have control of the wireless router to do this. If you do not, then consider doing your own Internet connection and wireless router. Addition to the steps of General safety below, make sure that file/printer sharing is DISABLED.

    The result of all this is to keep on the front of your mind is that security, physical access to a machine trumps all. If you do not trust the people with whom you live and/or people who visit them, you have to keep the computer with you or in a locked environment that no one else can enter. And of course the locks can be chosen. Or find the best people to live with. I understand that this is not possible in your real world, but I'm telling you all the options.

    Computer security - any computer running an operating system is accessible by a person with 1) physical access; (2) time; (3) jurisdiction; (4) tools of. There are a few things you can do to make it a little more difficult but:

    1. define a password in the BIOS that must be entered before starting the operating system. Also to set the supervisor password in the BIOS so the BIOS configuration cannot be entered without it.

    2. starting at the BIOS, change the order of boot to hard drive first.

    3. set strong passwords on all accounts, including the built-in XP administrator account (it is disabled by default in Vista).

    4. If you leave your own account connected, use Windows key + L to lock the computer (or set the screen/power economy saver) when you step away from the computer and require a password to use.

    5. do the other accounts of users limited in XP Home, regular user accounts in XP Pro. All users must be on a Standard account in Vista with an administrator account (called something like 'Tech' or 'CompAdmin') only used for purposes of elevation.

    6. If more than one person uses the computer user set permissions/restrictions:

    If you have XP/Vista/Windows 7 Home, you don't have the built-in ability to create fine-grained limits. In XP and Vista, you can use the Security Console or MVP Doug Knox or the program MS SteadyState to set restrictions as you wish. SteadyState now supports Vista but not Windows 7. Mr. Knox security console may still work in Win7.

    http://www.dougknox.com
    http://www.Microsoft.com/Windows/products/winfamily/SharedAccess/default.mspx
    Information about SteadyState - http://aumha.net/viewtopic.php?t=27570
    SteadyState support - http://social.microsoft.com/forums/en-US/windowssteadystate/threads/
    SteadyState How - to (not supported in Windows 7 still) - http://www.howtogeek.com/howto/6520/windows-steadystate/

    Please understand that these are technical answers to what is essentially a technical problem and there are ways around these precautions. It is a problem of family / interpersonal which cannot be solved by technical means.

    Establishing a safe wireless router - have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

    http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

    This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the password by default because everyone knows the default passwords for different routers.

    Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

    Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

    Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

    At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

    If you want to develop me on this or have any other questions, feel free to ask. MS - MVP - Elephant Boy computers - don't panic!

  • G61 laptop screen

    I'm looking for a replacement to confirm, the question of the video card for my laptop and availability, the cheaper cost.

    All diagnostics have been run, several times to determine the BIOS flash County white screen problem light and all other suggestions run, including an additional monitor, without success.

    Hard drive, hard drive, everything works, or to her sounds less as it is tempting to work as on-site necessary starting point, just a white screen. Points of final diagnoses to the video card as the culprit?

    With all the new systems available around $300, would like to know if it is the video card and if it is a value of the correction, or just buy a whole new system?

    G61-511WM

    Windows 7

    Hello, @mechanic673

    If everything (all the troubleshooting and diagnosis) is oriented toward the Videocard is a problem, then it is most likely is. It would be a starting point, if you are looking to get the laptop working again.

    There isn't a way to know 100%, if the video card is indeed the problem. I say this as this seems to be the answer you are looking for, a guarantee. That, I can't provide as there's a chance something else could be the problem, but again, this is where you were directed by troubleshooting. Replacement of the card may very well be the solution. At this point, it's really an appeal from the judgment for you to do. You pay for the graphics card and try it? Or did you just buy a new laptop. That can be made for you, I can only say that the information provided (read through the old post on this) points to the graphics card.

    I say well that, if you are looking to buy a laptop in the range of $300 (as you mentioned it), keep in mind what you want than this to do. If you are pregnant run heavy apps or games, a computer laptop $300 will not cut it. You would look at the $700 or more depending. Now, if everything you need is a graphics card and it runs you need, then it might be less expensive.

    I hope this gives you an overview on the course of action to take for the question. If you have other questions about this, you can always contact support to see if they have anything to add, or what kind of assistance they could provide.

    Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

    Thanks for posting on the HP Forums.

  • Real window7 after replacement of the processor and motherboard

    I bought authentic window7 and installed in my computer. Later, the card mother and processor changed because of problem and installed windows7 CD I own.  Now, it shows that the windows7 is not authentic. Please help me.

    Tibo Mathai.

    Hi Samuel,.

    You get an error with the message?

    Genuine Windows is a recurring process that checks your product key to ensure that it is not blocked or used on a different material that you were using when you activated Windows. If the product key is not genuine, it is likely that the product key is used on another computer or is a counterfeit.

    Real control, or the validation is done when your computer tries to download optional updates from Microsoft. For example, when your computer downloads updates, Windows checks to see if your product key is valid. If this is the case, Windows on your computer is genuine, and you are eligible to receive updates from Microsoft. If this is not the case, your computer is running non-genuine Windows.

    Take a look at this Microsoft KB article if you get the error code 0 x 80070005.

    Windows 7 displays "Windows is not genuine".

    You can also consult the suggestions provided by Keith from the link.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-is-showing-as-not-genuine/cbd43297-0e4d-458C-8487-9168c4cd668d

    Visit this link for your reference:

    http://Windows.Microsoft.com/en-in/Windows7/activate-Windows-7-on-this-computer

    Answer if you need help with the issue and we will be happy to help you.

  • Activation issue when replacing motherboard and processor, but no disc?

    Hello everyone. I replace my card motherboard and CPU. moving to 99 X and 5960 x. I will not replace my C drive. It's a free upgrade for Windows 10 so I can move it. What do I have to disable my subscription CC before moving and then reactivate after have replaced the card motherboard and CPU. Thank you Roman

    Hi Rkenosha,

    Hello everyone. I replace my card motherboard and CPU. moving to 99 X and 5960 x. I will not replace my C drive. It's a free upgrade for Windows 10 so I can move it. What do I have to disable my subscription CC before moving and then reactivate after have replaced the card motherboard and CPU. Thank you Roman

    I don't think it's necessary.

    But after getting the card mother and processor changed, you may need to sign in again.

    Sign in with your Adobe ID and password.

    Thank you

    Ilyes Singh

  • Image processor using the Adobe RGB profile

    Image through CS4 64 bit processor changes my CMYK in Adobe RGB files saving in jpg format.

    I have checked "include ICC Profile".

    It doesn't have any other action.

    Could someone enlighten me as to why this is happening please?

    And if there is a code I can change to force it to keep my chosen profile?

    I hope someone can help

    Thank you

    If this should not be...

    If (DocumentMode.RGB! = app.activeDocument.mode & DocumentMode.CMYK! = app.activeDocument.mode) {}
    ConditionalModeChangeToRGB();
    }

  • PSC 2355 all in one printing stopped after upgrade windows 8.1 scan is OK.

    I have a HP psc2355 printer worked happliy in window 8. I downloaded and installed windows store 8.1 and the printer no longer works!

    With the printer Open (via Control Panel) status window, the details of the document briefly appear when you click the button print. Nothing happens at the end of the printer. Theres nothing wrong with the printer as I can use it on another PC without problem.

    I uninstalled and reinstalled the printer using hppiw 2012-10-31 and the HP print and Scan Doctor V 4.1.0.29 which gives an error in device "your printer is in a busy state" after an attempt is made to print from applications or properties of the printer/print test page.

    that self-test prints OK.

    Scanner works OK

    Printer is connected via rirectly USB cable to the USB port on the PC

    Windows Update ran this morning

    3 hours lost so far!

    SOLVED * printer properties Advanced tab Print Processor change Print Processor to winprint hpzpplhn settings check the default data type is RAW print OK now HP has gotten support jobs going?

  • Satellite U200-196: new BIOS v.3.40 works

    Hello

    Just installed the new BIOS for Satellite U200-196 v.3.40. Works very well but as usual, I don't know yet what they changed. Take a look on the American page later.

    Cool that we have a new BIOS every week... But where are the drivers? I have my Vista here and you want to install. :)

    Edit: Changelog:

    Version 3.40 14/02/2007
    Added CPU support: optimized the thermostat during low temperature operations.
    This BIOS supports Windows XP and Vista.
    Version 3.30 27/12/2006

    Added the: Windows Vista features
    Added: Toshiba Device Access Control Utility V2.0 support
    Added the: requirements of Intel Core2 Duo (improved stability when using Intel Core 2 Duo as a Single Core processor)
    Change: The LCD screen refresh rate is therefore more 59Hz in Vista. (VGA BIOS change)
    Change: Pixel Clock (change in BIOS VGA)
    Fixed: The combination of a BIOS compatible Vista SYSTEM and no - BitLocker Boot Block is no longer shows an exclamation point (!) for the TPM device in Windows XP Device Manager.
    Version 1.50 06/12/2006

    Requirements of Intel incorporated for improved stability of chipset.
    Version 1.40 25/09/2006

    Apply the update for Napa Merom processors
    Made changes to comply with June 2006 Specifications Intel logo
    Made changes to comply with Guide R0.90 of Intel Core 2 Duo Mobile processor BIOS writer.
    Made changes to comply with Guide R1.00 of Intel Core Duo Mobile processor BIOS writer. (The family code changed processor)
    Correction: The CRT picture even if LCD + Analog RGB is selected for the power on the display setting.
    1.20 version 04/08/2006

    Added CPU Tj85 support.
    Support added to the temperature thermostat.
    Added support to monitor external widescreen.
    Version 1.30 24/08/2006

    Requirements of Intel incorporated to optimize performance memory chipset.
    Version 1.10 25/04/2006

    BIOS for Satellite U200/U205 of initial production.

    This is a great information;
    New Bios is out and now the Vista drivers are also available for U200 laptops.
    I must say thanks to Toshiba

  • Satellite A210 - 16G - problem of CPU frequency and memory

    Hey guys,.

    I had a problem with my laptop I can't solve, since I installed windows 7 RTM x 64 version.
    I noticed something is wrong after finding that my Windows experience index has fallen to 2.7 instead of 4.5, I used to have on Vista. For those who do not know my characteristics are:
    AMD Turion 64 X 2 TL-60, which I've got 2.7 of note, 4 GB Kingston DDR2-667 (333 MHz) - 4.4, scores of charts and hard drives are the same.

    I read in one of the forums that it may be a problem with the standby power options, but he did not get any option that says on the frequency of the processor changing according to the plan of the power. I also installed new version 2.0 of the website of Toshiba BIOS, but it only makes things worse: I've got 6.0 rating graphics of games but the Perf of Aero desktop is now 1.0!

    I installed diagnostic software: Everest and CPU - Z and I discovered that my CPU works with a frequency of 800 Mhz (the multiplier is 4 x, voltage 0.8V) and my DRAM frequency is 159.8 Mhz (I don't know if it's ok, but I know that 4.4 score is certainly too low although).

    So tell me guys, is this a problem of the operating system? Should I try to install the 32-bit version of Windows 7, or it won't change anything? Maybe I should try some software that would change the frequency of my FSB?
    I'm waiting for your answers, because I don't know what to do.

    Paul

    Aero needs a WDDM compatible graphics driver, then try to update the graphics driver on the Toshiba site

  • B310 recognizing no more than 4 GB of Ram

    My B30 acknowledges no more than 4 GB of Ram, although Windows 7 Home Premium 64-bit and the motherboard maximum of 8GB.

    The link here confirms it:

    http://forums.Lenovo.com/T5/IdeaCentre-desktops-home-servers/processor-change/m-p/1070365/highlight/...

    Someone at - it a solution?

    Reinserted memory sticks and alls fine now :-)

Maybe you are looking for

  • W520 Bios Update Utility 10 64-bit Windows

    Friends Earlier, I had a Thinkpad W520. Looks like a powerful machine. He already started level Win 10 Pro 64 bit. Now I tried to update the BIOS on this issue but don't know how to proceed. The current BIOS is: BIOSLENOVO brandVersion 8BET55WW (1.35

  • Open to create problems replace with the recording of file templates

    Hello, I had a problem with the function open/replace/create. Could you please specify each function, how it works? As you can see in my file, I try to record in the specified path. The values appear in the text file, but when I change some values in

  • Microsoft Flight.Can't connect to the flight MS Server

    I played with MS Flight on my Windows 7 computer for more than a year, and yesterday, I signed in and discovered that everything works except Aerocache. I get the message "unable to connect to the server of flight." I uninstalled the flight and then

  • Win7 VPN connects - returns the error code 806

    I use Win7 Ultimate, and try to establish a VPN connection to a job server.  I have a XP Pro system which connects OK but cannot get W7 to.  I have install the VPN as close to the installation of XP as I can but it works always... it refers to what a

  • How to assign a range of interfaces to a single VLAN?

    How can I assign ports or multiple interfaces to a single VLAN. I use multilayer switches.