HP g62-149wm webcam

Similar Questions

• HP G62-149WM MOTHERBOARD

  I need to replace my motherboard. Number of room so that it is 595184-001, but when I look up the same part number of HP Service & parts web page here shows them only saw 2 × 2.0 USB ports but mine has 3 × 2.0 USB ports... If anyone knows why this is or where I can find the motherboard correct for my HP G62-149WM, who made the 3 USB ports? Thank you in advance for your time and your help in this matter! Ron

  Here is the Manual:

  Repair manuals

  See page 4-33. The third USB port is on a daughterboard, not directly soldered on the motherboard. If the motherboard itself has just two usb ports on the left and the right one is on a small Board. When you replace the motherboard, you can reuse the daughter card to give you this third USB port.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Upgrade the hard drive on my HP G62-149WM for a 750 GB,

  If I upgrade the hard drive on my HP G62-149WM to a 750 GB drive (or maybe a 1 to) and use the factory purchased the set of recovery disks, it will install the recovery (hidden) on the disk partition, or not?  What IS the recovery partition, it will install (if installed)?

  Oeagleo wrote:

  If I upgrade the hard drive on my HP G62-149WM to a 750 GB drive (or maybe a 1 to) and use the factory purchased the set of recovery disks, it will install the recovery (hidden) on the disk partition, or not?  What IS the recovery partition, it will install (if installed)?

  Hello

  You can certainly move to a 750 GB 5400 RPM HARD drive, a 1 TB would also be possible, but it is not listed as a compatible hdd in a service guide. After a reset, the laptop will be in the same condition that you used for the first time (OS preinstalled). The recovery partition is going to be on the hard drive as well. Size is not too large, I think that it would be up to 15-20 GB...

• G62-149wm: OS after you replaced the HARD drive

  I was good recently a laptop G62 with a hdd dead by a friend who did not feel it was worth the cost of repairs. I tell myself that I can put an ssd inside, and it will be a pretty decent laptop.  My problem concerns the operating system after that I do this. I have my own copy of Windows 7 (64 bit), but I read that the key for the original version on the dead hard drive is also on the bios for faster installation. And if you install a different version, it can cause problems with some versions of windows in some laptops. My question is can I use my copy of windows 7 or what I have to go through the trouble to use the key to laptops to burn another copy of the windows Web site. Possible stupid question but I want to know everything before you start this project.

  Hello

  This machine originally shipped with Windows 7, then you will be very well - injection of digital product keys started with Windows 8 - just install Windows 7 and enter your product key from the usual way.

  If necessary, original software and drivers are available on the following link.

  http://support.HP.com/us-en/drivers/selfservice/HP-G62-100-notebook-PC-series/4078809/model/4164687

  Kind regards

  DP - K

• HP G62-149WM/updated software driver for card MicroSoft Virt.WiFi Miniport

  (OS = windows 7 Home Premium)   PROBLEM = IN DEV. MNGR. updated SOFTWARE (MICROSOFT VIRTUAL WiFi MINIPORT ADAPTER) a MESSAGE WINDOWS SURGIT IN SAYING some THING LIKE "IT DON'T RECOGNIZE the PUBLISHER OF THE DRIVER SOFTWARE", THEN ME GIVES OPTIONS to EACH UPDATE DRIVER any WAY OR BASICALLY NOT TOO... SO I GUESS MY QUESTION IS "HOW TO KNOW WHERE TO FIND THE RIGHT DRIVER FOR ABOVE MENTIONED ADAPTER IN ADDITION TO WITH AUTO WINDOWS." UPDATE? I'D APPRECIATE ANY HELP REGARDING THIS ISSUE AND I THANK YOU ALL IN ADVANCE!

  The Microsoft Virtual WiFi Miniport is a driver built into Windows 7 and should not need to be updated. The correct version of the pilot was installed when Windows 7 was installed and no new updates of this driver is necessary. If and only if, Microsoft has released the update of the driver, you are trying to install, you should install it. Please check the source of the driver before installing this doubtful driver.

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• HP G62-149WM TROUBLESHOOTING SCREEN

  Need help ASAP! Hello aid... so here's the problem! I decided to turn off Internet Explorer through the OFF... but TURN WINDOWS FEATURES ON AND after it restarts, my screen resolution is at 1280 × 800 and I don't know how to get back to his original 1366 × 768! There is now a strip of inch long black on the right side of the screen! I turned MY back 11 but sound still there! I removed the battery/power cord and power supply for 25 seconds, but still didn't work! I would appreciate your help in this matter and I thank you all in advance!

  OK, problem solved! Had nothing to do with software, drivers, etc., it's the new display cable which was kinda stuck! I noticed, that he was not the "stretch" that the former had years of use, so it is a real good interlocking and studded bezel or it may have came off the screen very slightly to where it was not connected to all the pins! Its works fine now... Imagine that! So after reinstall 2 different version of windows (7 & 8.1) not exactly knowing the problem, now comes the monotonous task of installing updates AGAIN! I'm so good with it! Have a good! And thanks again!

• Driver Intel Turbo Boost Technology (taken from HP's Support site)

  Hello Forum members!

  OK, so roll with me here! I have a HP G62-149WM I upgraded to it is (out of the box) Windows 7 Home Premium 64 Bit for Windows 8.1 Pro 64 Bit... Then I went into page HP driver download to install the Turbo Boost driver well, as you know, it basically requires you to type in your model, you choose what operating system runs your make and model, and then it shows all the different drivers, right? So my question now is because it does not show 8.1 Windows as an operating system option, the Turbo Boost driver always works on my 8.1 win even if it was made on a technical level to work on Win 7? Thank you in advance for your time and your help in this matter!

  Ron

  Hello @ronnieron ,

  Welcome to the HP Forums!

  Unfortunately, this has not appeared to get coverage Windows 8.1 with respect to the drivers. You can try to install the Windows 7 driver, which might work, but it probably does not work well, or not at all.

  Here's the driver page, in case it becomes necessary: Drivers of laptop HP G62-149WM

  Please let me know if you have any questions or concerns. Thank you!

  Mario

• Cannot get past Boot Screen manufacturer

  I can't get my g62-149wm to go beyond the HP screen. I tried to hit escape to go into the boot options and f10 to enter the BIOS but nothing happens. It is blocked here. Anyone have any ideas?

  Do like me. I had to buy a SATA docking station, and then start on a live usb Sabayon linux (without the internal hdd is present) and back up all the data on my external hard drive. After the backup, I just formatted the internal hard drive and recovery DVDs to restore factory settings.

  You can also do a new installation or anything else you want because the laptop must be initiated with the hard drive in it. I don't have any other PC to make a back up so had to use this usb flash drive or a live cd (needs all flash usb plugged) with linux on it.

• Upgrade my i5 to i7 cpu?

  Hello help! I have a HP G62-149WM with an Intel Core i5 - 430 m processor and would like to know if I can pass the processor i7, such as listed in the service of HP for my make and model Guide? Just want to be sure before that I agree! Thanks in advance for your time and your help in this matter!

  Hello

  Yes, you can replace it-

  Manual: http://h10032.www1.hp.com/ctg/Manual/c02542455.pdf

  Page 4-47,

  HP 587259-001 part number

  http://PartSurfer.HP.com/search.aspx?SearchText=587259-001

  Online:
  http://www.Amazon.com/GP/AW/d/B008FQP89O?pc_redir=1407160273&robot_redir=1

  Kind regards

• I need software youcam downoad

  I can't find the software download youcam to my hp g62-371dx webcam.

  Hello

  Please use the following link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us&LC=en&DLC=en&softwareitem=ob-78419-1

  Kind regards.

• HP G62 webcam

  I just bought this laptop.

  Can't get the webcam integrated without Messenger to take pictures.

  Do I need a program or another cam?

  That's great!

  The answer was there in itself: CyberLink Youcam!

  Sorry for the inconvenience

• The G62-361TX notebook webcam does not work.

  Hi all!

  I have a problem with the webcam after installation of operating system Windows 7 Ultimate x 64 charges. It was working fine before with the same OS, Webcam light always ON the beginning of "windows boot.

  I tried to uninstall and update the driver, nothing seems to work.

  Webcam is not detected in Cyberlink Youcam when I opened the application of YouCam webcam (white) light goes OFF, then the LED lights once more when I close the YouCam application .

  Don't know what to do next.

  Help, please!

  SSA

  The problem was faulty Webcam (material). I had solved with the new party in the Service Center HP for free since my laptop is under warranty.

• my hp g62 webcam is enabled - now, how can I access it

  I downloaded Cyber Cam and was able to use the webcam in my HP (HP G62t).  However, as I removed Cyber Cam I was not able to use the webcam.  I checked on the master device and the webcam is turned on and the software and drivers are up to date.

  How can I access the webcam on this laptop.  Help!  Thank you-

  Alonzo

  Please check to see if you have Cyberlink YouCam on your laptop, I believe that it is the application with which we embarked on what you can use the webcam.

  Thank you for your response, thank you.

• Webcam does not appear in Device Manager

  I have a model of portable pavilion G62-233NR windows 7 64-bit, with a built-in webcam.  YouC'm software was bundled with it and worked.  Now the webcam is not found by one of the video programs AE Skype, Youcam... etc...

  I also noticed that the webcam does not appear in Device Manager. I tell me that I have to reinstall a driver for it but do not know what driver to install. HP has the following availble drivers for my model but which?  If one of the pilots was labeled "webcam", the task would be easy. I hope because the driver is missing in Device Manager that has installed a driver will set missing cam... I'm worried because I don't see a driver named "webcam" in the list... but what else could the problem, how can I get the driver installed, if that's the problem.

  Hello world

  I have windows 7, in the balk suggestion you type cmd

  then you have a suggestion, then you must right-click of the mouse and select administrator. otherwise, you will not be of addministrator and you can not make the order.

  Greetz

  Steve

• Available to the pins of the webcam module

  I'm building a detector simple alpha particle and want to use this webcam that I'm waiting to receive. So I hope someone can help me understand what the pins are on the webcam module.

  As the picture below shows the number of spare parts is 626656-001 and the list of products, it is used in can be found here: http://partsurfer.hp.com/Search.aspx?SearchText=626656-001. I searched for useful patterns, but without result.

  

  Thank you!

  Having received the cam [1] and the corresponding cable (P/N DD0AX6CM002) I did a second round of research and came up with the answer in an old NET [2]. The user CompRepairGurus referenced schemas [3] and provided this image:

  

  This information has been verified by seeing how the pin 1 and 2 related to a twisted cable pair and using a multimeter to verify that the PIN 4 and 5 have a connectivity with areas of grounding of the module camera (scew holes).

  So the answer regarding the image in the first post is:

  A = pin 1 Data +.

  B = pin 2, Data-

  C = pin 3, + 3.9VDC

  D = pin 4, ground

  E = pin 5, soil

  ---

  [1] camera module Info:

  Suyin-A
  
  DB06501 SYZLR69
  
  AI000319000 R010000
  
  HF0319-J310-OV01 AXM/SXD-AXL
  
  E154554
  SH - M1 (II) 94V-0
  JMB310 + OV7675

  [2] DV5 webcam pinout, post #10 - HP Support Forum's

  [3] HP G56 - G42-G62 schemas, Compaq Presario CQ56 - patterns of CQ62, 31AX2MB00D0, DA0AX2MB6E0, DA0AX2MB6E1, AX2 - AX7 motherboard schematics