HP laser jet 1320n

Similar Questions

• Slow data transfer between computer and HP Laser Jet 1320n

  I recently bought a laptop with windows 8.1 and successfully connected to 1320n times via LAN and wireless networks. Problem is when I try to print .pdf files, data transfer from my computer to the printer seems very slow and that's why it takes several minutes to print 10 pages. On the print window of my system, it tells me the data to transfer a file from pdf page 14 are about 75 MB.

  My questions are:

  1-is-normal this size of data?

  2. What can I do to increase the transfer speed?

  Thank you in advance.

  H.A.

  Thank you very much for the reply.

  I hae has solved the problem by installing the drivers that are on the product page (I was using the Windows drivers when I had the problem). Everything works as it should now.

• Laser Jet 1320 PCL 5 error stays on

  Hello

  1: laser Jet 1320 PCL5

  2: Windows 7

  3: the error described below light distribution

  4. no change

  Light orange error on my Laser Jet 1320 PCL5 is constantly lit, while the two green lights flash underneath. Pressing the green button does not help.

  I checked for paper jamming, paper etc. tray problems. Nothing has been found.

  Power off the printer for a minute did not help.

  My printer to PC Board information tells me that my printer is "Ready!"

  I'd appreciate any help.

  Thank you

  Arnold

  SOLUTION - I bought a 1320n renovated on Amazon for £69.It arrived today. Like new!  A bargain!

• Color Laser Jet MFP M277dw Pro: frequently updated software

  I am the owner of a color Laser Jet MFP M277dw Pro. I get updates almost every week, and the software update is very strange. I'm clicking on the update system, it takes a lot of time to meet up with the text saying I'll remove the actual update or add another device. When I say no, thanks, I'll get a message saying that my update was successful (but only if I have to cancel this message). I don't understand why I have to go through this illogical question. Also, I don't understand why it is not necessary to update very frequently, especially when there is no explanation of the reason why.
  
  The two just exclamation points annoy me because I think that there must be a problem with the software, even if the printer works well.
  
  Sincere greetings
  
  Arne H. Wilstrup
  Denmark

  AHW

  Greetings @ahw,

  Thank you access the Forums from HP Support for extra support! I see that you have problems with updates of window for the printer software. I'd love to help you.

  Given that the printer works, I would say to hide updates.

  A poster tried to show or hide updates and it solved their problem.

  • How to "hide update" during the Build 9926
  • Need for the old Windows Update, not the new Windows Update
  • Windows 10 - where is the 'hide or show updates' hidden feature
  • How can I hide this update in Windows 10?
  • How to hide Windows Update, Windows 10 build 10061?

  You can also give your feedback to Microsoft, and if all goes well, they will release an update to correct the function of the operating system. You can learn how here; Updates and feedback.

  If this helps you to find a solution, please click on the button "accept as a Solution. If you wish, to say thank you for my effort to help, click on the 'Thumbs Up' to give me a Kudos. Please let me know the results. Good day!

• HP 3050 laser jet

  I have a new Dell computer that runs on Microsoft windows 7 (64 bit) then my laser jet setting all in one that I wonder what download of HP to get hooked. I chose the largest size (I think that pl6?) -in any case, the printer works fine as well as the fax, but I can't scan. I see a place that maybe this laser 3050 part scan jet only works with a 32-bit system-Please HELP

  Hi there bazilwood2;

  Suggestion quick let;
  

  
  Your HP 3050 laser jet is a commercial product. I suggest you post in the forum for HP Business Support for a better chance to find a quick solution.

  This is the page for your printer business support

  http://h20000.www2.HP.com/bizsupport/TechSupport/home.jsp?lang=en & CC = US & prodTypeId = 18972 & prodSeriesId = 1140783 & Task = & lang = to & CC = US
  
  You will find the commercial Council of Laserjet here.
  http://h30499.www3.HP.com/T5/printers-LaserJet/BD-p/BSC-413
  
  Hope you find the help you need;
  RobertoR

• HP Laser Jet MFP M127fw Pro: Reduce the font size of iPad Air

  I installed the HP ePrint app on my iPad Air and print by AirPrint on my Laser Jet Pro M127fw MFP printer. The font size is too large on the print job. How can I reduce the font size for my iPad Air printing?

  A big thank you to ice at the service of the cloud, the problem has been completely resolved.
  Thanks to the team

• laser jet mfp m127fn pro: need manual for laser jet pro mfp127fn

  There was no selection board for printers.     I need the manual for a laser jet mfp 127fn pro.  whenever I click on this manual, on the website of hp, I get a blank screen with a tiny 'x' in a small circle at the top left of my screen.   can someone tell me why I can't access the manual?  I do not have a firewall.

  I'm happy that using another browser worked for you.

• Laser Jet P1102s: Win7Control Laser Jet P1102s Panel question

  After the successful installation of my new Laser Jet P1102s on Windows 7 (32 bit), I found two icons in the control panel (see attachment). One is on the right side OK - the printer works well. But there is a sort of warning sign near the left ikon. Someone knows the reason or the sense of that?

  THX

  Hi Hegefer,

  Thanks for letting me know that the icon was not restarted.

  I think that's the Smart Install which automatically load the printer again on the restart and we can simply turn off so that it will not continue.

  Here are the instructions if you want to proceed when you have time.

  Follow these steps to disable the Smart Install. Select printer not PC:

  On the Windows computer, go to start, computer, right-click the CD for the

  printer and left click Open in a new window, go to smart util/siutility.exe/HP install utility.
  Shows printer or PC - select printer.
  Then click on disable.

  Have a great weekend!

• Laser Jet P1102w, need to factory reset

  Hello. I have a Laser Jet P1102w, which I had set up to print wireless before and had difficulty. So in the integrated Web (EWS) of the printer server I set up with an IP address manually and subsequently he fiine. Then my ISP sent a different router that I have implemented. Unfortunately I did change the IP address manually on my printer to the integrated Web server, first of all. Oops!

  In any case, I reinstalled the printer using the original HP DVD installation disc and also downloaded all updates firmware and HP Scan and print doctor. But it will not complete the wireless installation, I get an error message: "the printer has been able to connect to the network wireless using the wireless identification information.  However, this computer is unable to communicate with the printer.  Please check printer is on the same network as the computer and try again. »

  I am able to print a page of Self Test/Configuration of the printer which shows the old manual IP address that I had put in the SAP. Of course this IP address will not bring up the SAP any longer so I can't change it to manual. Config page shows also that my printer is on the new network, as it's my computer. I think that printing held back by not being able to connect with the new router from this router is an IP address anywhere near manual that I put on the printer (if necessary).

  I saw in the other responses to requests for similar information that I can get rid of the IP address manually, if I do a factory reset. Except that I do not know how. P1102 w doesn't have a 'control panel', just the wireless button and another "X" button - the one who insisted to get the Configuration Page. Press together does not reset anything.

  Can you tell my how to do a reset to the factory settings? Or think of another way, I can get into EWS printer so I can fix this? Or another solution?  Thank you!

  Hi, me again. I managed to reset the printer by following these steps: 1. get off the printer. 2. press and hold pressed the buttons 'X' and wireless at the same time and then press the power button. 3. always held the X and the buttons wireless for a total of about 15 seconds to push at the start. Then released.

• Laser Jet MFP M127FW Pro: Will not stop "hologram fax page 1" and is stuck in this mode

  I have Laser Jet Pro MFP M127FW.  This morning, a fax came through, and printed, however, the touchscreen rpet ' Print Fax: 1 Page, "with absolutely nothing to print.  I can now no longer print documents, or send and receive faxes again.    When I leave on this screen, the message disappears and comes back about a minute later for inactivity.  I tried to unplug and plug the unit in the.  I tried to use the switch to stop the machine.  When the powers of the slot machine, he will immediately return to the ' print fax Page: 1. " I tried clear memory and also the power resets. I keep reading on a Ret NVRAM and I would try it, but can't find anywhere it is displayed!

  It is a real problem for me because I use the fax machine throughout the day!  Can someone help me?  Thank you so much in advance!

  Hey @nhorn1115,

  Welcome to the Forums of HP Support!

  I understand that you have a fax job that will not print from your printer Laserjet M127fw range. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. When done, remove the cable from the back of the printer's fax. Now:

  1. Click on the configuration icon that looks like a key.
  2. Click on Service.
  3. Click Fax Service.
  4. Click clear saved faxes.
  5. Connect the cable of the fax.

  Please let me know if this clears the stuck fax. If so, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• HP Laser Jet 4250 printer: installation Laser Jet 4250 Windows 10

  Laser Jet 4250 is compatible with windows 10?

  If you still can not get the printer to work with usb, this printer has 2 EIO slots, and you can use one of these locations to insert a network card EIO (610N, 615N and 620N) which are not that expensive on ebay. Once you install the network card, you will be able to connect the printer to your router or switch if you have one and then have computers attached to the printer by using tcp/ip.

  http://www.eBay.com/ITM/HP-Jetdirect-610n-EIO-10-100TX-Ethernet-print-server-J4169A-/311722173327?hash=item489416e38f:g:mBMAAOSw - kdXyeCv

• Laser Jet Pro MFP 177fw: cannot scan with Laser Jet MFP 177fw Pro

  I have been using my 177fw Laser Jet Pro MFP on a Mac 10.10 for awhile.  Print, fax & scaning all worked.  I can scan is no longer.  I get the message "the scanner has not completed analysis" (there may be another message before that but it crushed until I read.).

  I use a USB cable for the connection.

  On August 31 I got HP Printer Software Update Verson 5.  What is my problem?

  Thanks for your help.

  Hi @scg117,

  Welcome to the HP Forums!

  I noticed your post about how you can't scan with your MFP HP Laserjet Pro 177fw on your Mac. And I'm happy to discuss this issue scan for you!

  To confirm that the hardware of the printer is functional, you are able to make a copy with the glass of the scanner of the printer?

  To copy:

  1. load the document on the scanner glass according to the indicators on the product.

  2. close the scanner.

  3. on the product control panel, press the button number of Copies.

  4. Select the number of copies.

  5. press the black start copy button or the button color launch copy to start copying.

  Let me know if it works, or if you see another error message.

  If the copy works, then try the steps described in this guide, Scanner USB connection is lost (Mac).

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope this post is helpful!

• Laser Jet P2035n: can not find the drivers for my printer

  Hello

  I need to take my computer back to General factory and I am trying to reinstall the drivers for my Laser Jet printer model # P2035N for my line of EMSL Hp Pc.   When I search drivers on the Hp website I find my printer features, but after watching I can't locate the section to download driver.

  Can you please show me where anyone and also is there a specific tab to select to start the download. Thank you, Jerry.

  I found your site with a quick Google search. http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=3662050&swLangOid=8&swEnvOid=4063

• HP Laser Jet Pro M251 nw: HP Laser Jet Pro M251 nw do not print Green

  I use a HP Laser Jet Pro M251 with Mac OS more recent Sierra 10.12. I tried to print a document in color from Excel and others a good percentage of the document should be printed in green. Instead of green, a very light, in some cases the struggles of the naked eye to see light YTYPE prints instead of GREEN. I then ran a test of the printer color page of the utility application of HP and there is no green anywhere on the page.

  All of my cartridges are 80% full or higher and I use the same newspaper, I am using since I bought the printer a few years ago. Indeed, nothing in my usual routine (for example all consumables and accessories) has changed. So, for the most part, my printer is not good for color printing.

  If anyone has had this problem and, more importantly, knows how to fix? I don't want to buy a new printer, but if I do, and if this problem is not easily corrected, I will not buy another HP. I'll check Consumer Reports to get advice on a new laser printer. I really liked this good printer and have, until today, thought it was an absolutely fantastic printer.

  Please help if you can. Thank you for your useful answers.

  RG

  RG

  Just a tip, I discovered the problem. It turns out that the Cyan cartridge was not good.

• Laser Jet 4000N: printer driver for Laser Jet 4000N to work with Windows 10 (64-bit)

  Hello

  Could you please tell me what I can use for HP Laser Jet driver done 4000N (with 10 (64-bit) Windows).

  The driver is available? If not, is there an alternative?

  During the installation of the printer, Windows 10 offers the following drivers: (all are for HP Laser Jet 4000 series):

  PCL5

  PCL6

  PS

  and for HP Laser Jet Series 4050:

  PCL 5

  PCL6

  PS

  Thank you in advance for your help!

  Hello Cyber,

  The best for these printers is the PCL 6 driver.

  Kind regards