HP Laserjet 1025nw printers takes almost 6-7 seconds before its starts printing.

Similar Questions

• Devices and printers takes a long time to open

  In Windows 7, the devices and printers open almost instantly. In Windows 8 Pro x 64, devices and printers takes almost 30 seconds to open, and it takes a long time whenever I open it. How can I shorten the time required for the devices and printers to open?

  Before you answer, please note the following:
  • I don't get an error message when I open devices and printers.
  • I have not made any recent hardware or software changes to the computer.
  • I experience the same behavior when Windows 8 starting in a boot environment.

  My problem is solved.

  Instead of wasting time on generic solutions, I should look for a specific cause from the start. In my case, the problem was with my scanner. In devices and printers, I open my scanner and selected properties of analysis. On the events under Actions tab, Windows had chosen to 'Interrogate what program to run.' I changed it to "Start this program" and choose my scanner software in the drop-down list.
  Devices and printers now opens almost instantly.

• LaserJet P2015d: Laserjet don't feed paper unless I opened before each time

  Hi all, I recently have a problem with my Laserjet P2015d how can I get to print each page of a document, I need to open the hood before (like matching the ink cartridge) and then close it to print the next page. If I do not open the lid before you start printing, it light-error with a flashing orange alert indicator. It does not send the error codes to the computer but then I don't really see what it is. But from what I hear, it tries to feed the paper from the cassette, but fails, unless I opened on the front, then close it and for some reason it work just for a single page. When he tries to move to the next, he fails again. How could solve this, or is it a bust? Thank you

  When the bin is full the indicator says it's because the metal tray is all the way at the bottom of thie plastic frame, i.e. where he sat when he was full of paper and the drawer is closed.

  When you first put all paper in and looking at the indicator is shows a full tray until you close the drawer, then when the paper raises it shows the actual level.

  So at this point, that looks like you close the drawer, then paper comes up, if there is not a lot of paper in the tray it will feed a sheet but the mechanism which is to follow the set allows to fall and you get no paper feed more.

  So, you could have actually just a defective Board.  If you can find another P2015 to borrow a tray, can you could test.

• copy of photoshop take almost 5 minutes

  Hi all

  When I try copy/paste or make slide a simple vector of illustrator into photoshop it takes almost 5 minutes and both programs are block. I'm on a Core i7 2.3 with 8 GB of ram, so power and memory should not be a problem. Any ideas?

  Oddly enough, removing network printers was the cure. A pain if I need to print to be sure, but at least it works fine now.

• LaserJet 1025nw wps led does light, always!

  The WPS on my Laserjet 1025nw lights not... Press and hold the WPS switch down for 2 seconds or more, but the light still does not light.  therefore can not get printer to work with a wireless router that does not have the WPS feature.

  Computer system is MAC OX X Lion worm. 10.7.4,

  Hello Diederman,

  Thanks for the post.  I've included some links below that may help with this one.  The first shows another way to get it on your network.  The other one says why the WPS light does not.  The third is to know how to reset the unit to default settings.  Good luck!

  http://support.HP.com/us-en/document/c02518011

  http://support.HP.com/us-en/document/c02508605

  http://support.HP.com/us-en/document/c02471640

• Extract data from an xml file takes almost an hour to 2.5 M data.

  Hello
  
  Any help would be much appreciated. Extract data from an xml file takes almost an hour to 2.5 M. data is there a solution to this.
  
  WITH t AS
  (SELECT XMLTYPE (response) pass FROM dual
  )
  SELECT
  b.entity_id,
  c.INSTANCE_ID,
  d.attribute_id,
  d.DATA_TYPE,
  d.ATTRIBUTE_VALUE,
  d.outcome_style
  T,.
  XMLTABLE (XMLNamespaces ("http://schemas.xmlsoap.org/soap/envelope/" AS "SOAP-ENV"
  'http://oracle.com/determinations/server/10.3/rulebase/assess/types' AS 'type')
  , ' SOAP - ENV:Envelope / SOAP - ENV:Body / typ: assess-response/typ: global instance / typ:entity'
  PASSAGE t.col
  Path of COLUMNS entity_id VARCHAR2 (256) "@id".
  path XMLTYPE res_tmp2 'typ:instance') b
  xmltable (XMLNamespaces ("http://schemas.xmlsoap.org/soap/envelope/" AS "SOAP-ENV"
  'http://oracle.com/determinations/server/10.3/rulebase/assess/types' AS 'type')
  , "typ:instance".
  PASSAGE b.res_tmp2
  Path of COLUMNS instance_id VARCHAR2 (256) "@id".
  path XMLTYPE res_tmp3 'typ:attribute') c
  xmltable (XMLNamespaces ("http://schemas.xmlsoap.org/soap/envelope/" AS "SOAP-ENV"
  'http://oracle.com/determinations/server/10.3/rulebase/assess/types' AS 'type')
  , "typ:attribute".
  PASSAGE c.res_tmp3
  Path of VARCHAR2 (256) COLUMNS attribute_id '@id '.
  , data_type VARCHAR2 (256) path '@type '.
  , attribute_value VARCHAR2 (256) path '.'
  path VARCHAR2 (256) outcome_style '@inferred') d;
  
  Thank you
  Mhand

  OK, in this case the best option is to store the answer in a binary table of XMLType (may be a temporary table if you want to) and run the query from there:

  CREATE TABLE tmp_xml OF XMLType
  XMLType STORE AS SECUREFILE BINARY XML -- default storage in your version
  ;
  

  INSERT INTO tmp_xml VALUES(XMLType(response));
  

  SELECT b.entity_id,
         c.instance_id,
         d.attribute_id,
         d.data_type,
         d.attribute_value,
         d.outcome_style
  FROM tmp_xml t,
       XMLTABLE(
         XMLNamespaces('http://schemas.xmlsoap.org/soap/envelope/' AS "SOAP-ENV"
                      , 'http://oracle.com/determinations/server/10.3/rulebase/assess/types' AS "typ")
       , 'SOAP-ENV:Envelope/SOAP-ENV:Body/typ:assess-response/typ:global-instance/typ:entity'
         PASSING t.object_value
         COLUMNS
  ...
  

• T450s startup takes 35 seconds before displaying the splash screen. (wake up 11sec)

  The following are my problems:

  1. when starting the machine, it takes about 35 seconds before the first activity screen (screen of Lenovo). After that, it starts normal.
  2. when waking off mode 'sleep', it takes 11 seconds before I see directed power stop to 'breathe' and wake up the screen.

  It feels like it is a hardware/bios on the issue, as (so far I know) hdd/ssd is accessible only after the bios has loaded and completed its audits of material. When you paste into a bootable usb it starts only flicker after the bios was loaded on the screen.

  Question:
  Anyone have an idea why my laptop waiting so long to start or wake? I don't mind wait a bit, but in 35 seconds + startup time normal is really boring. Especially with the fact that the laptop shows no sign of life for 35 seconds after ignition briefly the backlight on the keyboard. Alarm delay is also very annoying since even my 7 year old laptop BSOD to wake up faster, and I use a lot "sleep" mode.

  Some origins I think about:
  -Verification of the material during the initial start-up of equipment does not yet recognize a dedicated GPU card. (POST: Power On Self Test)
  -I don't think it's a problem with my software because the problems occurs before any media playback.

  I already tried things:
  -Reset the bios.
  -Start in legacy mode.
  -Update the bios
  -rebuild MBR (although I think that's the problem.)
  (- Refreshing installation of windows, even if I do not expect that's the problem.)

  This problem was already at the beginning (with origenal material):
  From the first time I started the laptop (with HARD drive), I noticed that it took a long time to start. I remember repeatedly pressing the button ON / OFF and think I did something wrong, when all of a sudden the 'Lenovo' screen appears.

  I hope someone can help me!

  My problems were solved!

  An engineer contacted me that they received a mainboard replacement and they wanted to make an appointment. I gave them the address where I worked the next day because I'm very mobile, and an engineer came by the next day. It appeared to be a qualified IBM engineer and test my machine and came to the same conclusion as me. He then did some tests to see if the problem was caused by something else, then the motherboard but eventually replace my motherboard with good care.

  After the replacement of the startup time and wake up was normal as it should be. I'm very happy with the service that Lenovo ThinkPad gave me.

  I have to add that when I called for the support that I got someone on the line who couldn't really understand me, neighter, Dutch or English. But it was also duo a bad connection, it seemed to me... But after that call I really didn't expect that it would come to a good end. I then really suppriced isn't 5 days later a Dutch engineer Chief called me for an appointment.

• When playing VLC media player it take about 20 to 30 seconds to open. When I push a right-click take about 3-5 seconds to open, why the difference?

  original title: on laptop
  I have a computer dell laptop (N4050). My lappi work slowly, when you play it take about 20 to 30 seconds to open the VLC media player. When I push right click it take about 3-5 seconds to open.
  so. Mr President, give me the solution to my problem.

  Hello

  1. which version of the operating system is installed?

  2. is the VLC media player-specific question?

  Try the following steps.

  Clean boot the computer and then try to open the VLC media player. Tuning your system to start in mode minimum state helps to identify third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  Reference:

  Optimize Windows 7 for better performance: http://Windows.Microsoft.com/en-us/Windows7/optimize-Windows-7-for-better-performance

  Slow PC? Optimize your computer for maximum performance: http://www.microsoft.com/athome/setup/optimize.aspx

  I hope this helps.

• Have 2 printers on the computer and the PC will not print one when you switch to the other?

  Have 2 printers on the computer and the PC will not print one when you switch to the other?

  Having a printer at the office and one at home, but use the same PC for both? Unable to print at home after bring you it to the office (and vice versa)?

  If you USB, most of the time, the PC will recognize what printer is which. Sometimes PORTS does not commute. You can manually change the correct ports if necessary.

  CLICK ON THE MENU START

  1 devices and printers

  2 right CLICK on the printer

  3. choose the PRINTER PROPERTIES

  4. click on PORTS

  5. There will be a list of ports with one (checked marked). If it's on the wrong port, change to the right pair and choose APPLY.

  (NOTE: it must ALWAYS be on a USB port or a wireless connection.) Some ports wireless start with a #(adresse IP) or a SERIAL number)

  I hope this helps. Sometimes, you can create your own port if you have more questions.

• When I open programs in Windows XP, the menu bar does not appear and it takes several seconds before the program responds (after that finally shows the menu bar).

  Everytime I open a program, it takes several seconds before I can do anything because the menu bar are not displayed immediately.  After the menu bar appears the function of programs very well, but it is very annoying to have to wait.  I've done an installation of Windows repair without success.

  follow the directions to this treatment... http://www.microsoft.com/windowsxp/using/setup/expert/northrup_restoreperf.mspx

• It takes two seconds before first reacts when I take action. It is only on my Imac on my mac pro.

  Any action, I do first (replace the CTI, insert clips...), it takes more or less two seconds before first reacts. It is very boring.  The problem is that on my Imac on my mac pro, that I have no problem.  I work with the first CC.

  Is there a solution for this problem?  Thanks in advance.

  Hi Meg the dog,

  I have re-installed the program, and it seems to work fine now. Thanks anyway.

• I am currently creative Member Cloud using the Plan of photography (paid annually).  I would like to take advantage of the upgrade promotion to the full level for $29.99.  Can I take advantage of the promo before it expires may 29?

  I am currently creative Member Cloud using the Plan of photography (paid annually).  I would like to take advantage of the upgrade promotion to the full level for $29.99.  Can I take advantage of the promo before it expires may 29?

  Contact Adobe Support by chat or phone to see what can be done...

  To the link below, click on the still need help? option in the blue box below and choose the option to chat or by phone...
  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Creative cloud support (all creative cloud customer service problems)
  http://helpx.Adobe.com/x-productkb/global/service-CCM.html ( http://adobe.ly/19llvMN )

  Phone support | Orders, returns, exchanges

  http://helpx.Adobe.com/x-productkb/global/phone-support-orders.html

• VMWare Workstation 7 (retail version) takes more than 20 seconds to load

  I am new to the community, so I hope I gave enough information background with my problem.

  When I was using VMWare Workstation 7 RC, enforcement would literally load in a few seconds. Because I bought the "expedition" of the 7 Workstation version, the program takes more than 20 seconds to load. However, once loaded, it works fine with virtual machines - but it is such an inconvenience.

  Here are my computer specs:

  Intel Core Duo Quad core CPU, 8 GB of RAM, Windows 7 Ultimate 64 - bit edition.

  Actions I take so far:

  I made a correct uninstallation of the RC, rebooted version and then install the retail version of Workstation 7. I also noticed that Workstation 7 interferes with Ccleaner (by Piraform). When I run Ccleaner, I get "unexpected error" messages and the program will not work correctly. So I uninstalled Ccleaner, but this has not fixed the problem with long load times. I also used the MSCONFIG Utility (such as published in a KB article) and hidden all the MS services and disabled the restrestarted, but it does not resolve the problem, either.

  Today, I made a Workstation 7 unistall and reinstalled Workstation 7, but same problem long loadtime. I am so puzzled as to why the RC version worked like lightning, and the retail version is so slow. All my other applications on my PC load and run fast as lightning.

  Have others experienced this problem? Does anyone have any suggestions, what else can be done to solve this problem?

  It seems you're having some sort of problem with the configuration of the proxy.  Your newspaper IU has:

  13:42:26.768 Nov 02: vmui | -VMware Workstation for Windows: install 7.0.0(-1) = new update = no!  URL = "id ="ws-windows"

  13:42:40.433 Nov 02: vmui | CDS error: could not determine the proxy for the URL https://softwareupdate.vmware.com/cds (12180)

  13:42:40.433 Nov 02: vmui | CDS warning: could not use file CAP or automatic proxy detection.

  Use a proxy server?  If so, could you try go to control panel > network and Internet > Internet Options > connections > LAN Settings and either:

  A. Unchecking "automatically detect settings".

  B. explicitly specify a proxy server manually

  ?

  Or try running workstation and will change > Preferences > updates and unchecking "check new software components according to the needs.

• Multifunction LaserJet 1536dnf printers: ADF rollers stuck in down position

  Feed documents through the ADF, the feed rollers will stay low and will only return to the position if the printer is power cycled. It is an intermittent problem. More of a nuisance than anything, but wouldn't mind getting this problem.

  Thank you.

  Hi @DeweyE,

  Welcome to the Forums of HP Support!

  I see that you are having problems with the ADF on your HP LaserJet Pro M1536dnf multifunction printer. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand that this ADF is in the correct position after restart the printer. Looks like there could be a problem with a lack of power that the printer receives, firmware glitch or the rollers slide.

  I would like to do a hard reset to see if that will solve the problem.

  • Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  • Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
  • Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.
  • Try to use the ADF again.

  Then, update the firmware of the printer. Click here to download it.

  In addition, I would like to try the steps in this guide if you are still having problems.

  •  "The document feeder mispick" Message appears on the control panel and the ADF is not Pick Up paper or feeds on several Pages

  If you have completed all the above steps and your product still has a problem, service the product.

  Contact HP for service in all countries except Asia-Pacific.
  First, check your product warranty to check your warranty printer status and then go to contact HP support to find an authorized dealer or to schedule a repair.
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number are displayed.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• Multifunction HP LaserJet 1536dnf printers: Scanner function not accessible after upgrade to Windows 10

  Function non-contactable on printers MFP HP LaserJet 1536dnf of analysis after the upgrade to Windows 10.

  Here is the error message:

  

  I recycled the printer... inaccessible even

  I recycled the router and the printer... inaccessible even

  Worked fine before with Norton and Windows Firewall enabled on Windows 7.  so...

  I have disabled the Windows Firewall (but not Norton firewall)... inaccessible even

  I ran "SCF/scannow' with the command prompt... inaccessible even

  I ran HP Print doctor who says that the scanning software was not installed.

  I tried to download and install the software the complete solution... masse not installed properly... even inaccessible.

  Help, please

  HALLALUJAH!  Now, I can scan, fax and print.  I did not follow the directions of RnRMusicMan together.  I just deleted all the HP software that had to do with print and then installed the suggested software.  I do not close the firewall or do any of the other suggestions.  Other people with the same problem may have to follow all the indications made by RnRMusicMan above.  RnRMusicMan, THANK YOU for giving me the link for the correct HP software to solve the problem, HP LaserJet full feature software and driver.   Without your help, I would have not a scanner works on this printer.  I scan most all instead of filing paper.  I was in trouble when the sweep would not work. ... HP support is GREAT!