HP Laserjet 3600 printer: Connect HP Laserjet 3600 to the network

Similar Questions

• Windows cannot find a driver for HP LaserJet 1022 on the network. To locate one manually, click on OK.

  Computer (win xp 32-bit) A located 1020 printer with sharing

  Computer B (win 7 64bits) successful connect through A computer printer share

  Computer C (win 7 64 bit)

  Computer D (win 7 64 bit)

  D C & computer appeared this message: -.

  Windows cannot find a driver for HP LaserJet 1022 on the network. To locate one manually, click on OK.

  When I click OK, I get an error message:

  Required file: INF for HP LaserJet 1022 printer driver
  The file '. INF' (unknown) is needed.
  Type the path where the file is located, and then click OK.

  On the Win 7 computer...

  Devices and printers
  Add a printer
  Add a local printer
  Select create a new port:
  Select Local Port for the port Type:
  Enter the name of the network to the XP computer that is. \\XPcomputername\LJprinterid
  Install the LaserJet 1020 driver when prompted

• Trying to share a HP printer (connected by USB cable to the desktop running XP) for the new laptop running Windows 7

  Hello

  I was able to share the printer between two computers, such as mentioned in the title, but I can not print from my laptop if my office (to which the printer is connected) is disabled.

  Is this in any way about this? I have a netgear router and Windows 7 contains the printer even when the office is off, but says that it is offline.

  Your help is appreciated in advance.

  Hello

  Around her, the only way is to get a network printer.

  Network printer is connected (or connect via Wireless) in the router and thus accessible by any computer on the network.

  Example, http://www.newegg.com/Product/Product.aspx?Item=N82E16828115634&cm_re=wireless_printer-_-28-115-634-_-Product

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• HP software detects the printer, but then "the printer could not be installed on the network.

  I tried looking for a similar problem, but have had no success yet.  I doubt I'm the first to this problem!

  The computer is XP SP3, is printer Deskjet 3050 has, and it's a WiFi WPA - PSK.

  The printer confirms that it is connected to WiFi.

  When I run the tool on the computer, to the point of network configuration check, the installation software detects the printer with the correct IP address.  It's the only thing he discovered.

  I click Next, and after a minute or two, I get the error "the printer could not be installed on the wireless network" click Retry to try reinstall the printer on the network, or click Cancel to return to connection options.

  This just cycles with no progress.  I have disabled the Windows Firewall and also disabled the AV.  No change.

  I can access the interface web printer - but still cannot install the printer.  It is listed in the printers and faxes as being offline.

  I'll try removing it again and add new-but-that someone has encountered this problem before, please?

  Well, my problem is almost solved. I uninstalled the software and then downloaded the software of the printer on the HP site where it is more recent than what was on the CD... and it's fixed!
  
  I can print wireless!
  
  Cannot scan, the printer gives an error, but that's OK for now.

• HP Deskjet 3515: Connection HP Deskjet 3515 to the network without USB cable

  Nice day

  I just changed networks and the need to install my HP Deskjet 3515 to the new network but I can't find my USB cable.

  Is - it possible configure the printer on my new network without USB cable?

  Thank you

  GatZza

  Hello @GatZza,

  Welcome to the HP support forums.

  I appreciate that you try to put your Deskjet 3515 on your network wireless without router.

  I would like to help.

  I got the following information from the Printers manual.

  To get started with Direct wireless printing

  1. to use live wireless, you must turn on Direct Wireless Control Panel and get the wireless
  Direct name and password if you have directly on wireless security:
  a. on the home screen, tap on wireless and then select settings.
  b. If the display shows that the wireless is turned off, select live wireless, then on (No.
  Security) or we (with security).

  NOTE: HP recommends that you turn on Direct wireless security. If you turn on safety, only
  users with the password will be able to connect wirelessly to the printer. If you disable security,
  anyone with a Wi - Fi device to the printer WiFi range will be able to connect to the printer.

  c. Select the display name to display the name Direct wireless.
  d. Select Show password to display the password Direct wireless if you live wireless
  Security on.

  2 from your computer wireless or mobile device, Wireless Tower, find and connect wirelessly
  Direct name, for example: 3510 HP-Print-XX-Deskjet series. If you have Direct wireless security, enter
  Direct wireless password when you are prompted. Then print as you normally would from your computer or mobile
  device.

  Open the integrated via Direct wireless Web server

  1. from the home screen, press the wireless button, and then select settings.

  2. If the display shows that the wireless is turned off, select live wireless, then on (No Security) or
  On (with security).

  3. from your computer wireless turn wireless on, to search and connect on behalf of live wireless, for
  example: series HP-Print-XX-Deskjet 3510. If you have Direct wireless security, enter in the wireless
  Direct password when you are prompted.

  4. in a browser supported on your computer, type the following address: http://192.168.223.1.

  When you reach the EWS printers, you should see an option to run the Wireless Setup Wizard.

  Run the wizard, and then follow the prompts.

• Windows 7 cannot print on a deskjet D2650 via the network

  I have a D2650 deskjet printer connected to a desktop computer running XP Pro - SP3 - updated

  I got a laptop with Vista professional I could print from via my wireless to the printer.

  I upgraded to a laptop with Windows 7 Pro and the laptop found the printer over the network, and I was able to print a test page, no problem. I then tried to print a Word document and nothing happens. I come back and print another test page... no problem. Try to print from other programs and... nada.

  I then installed the correct drivers for Win7 64 bit, connected to the printer and print anything very well. When I return to the network and try to print, nothing other than a test page.

  Any ideas would be greatly appreciated.

  Thank you

  To do this on the Windows 7 computer.

  Go to devices and printers
  Add a printer
  Add a local printer
  Create a NEW Port in the Add Wizard in the Control Panel Printers
  Select LOCAL port (unless your printer is a printer on a network with an address IP then chose TCPIP port
  Enter the name of the XP network or IP address
  Install the Win 7 driver

• I can't connect a Flir camera to the network

  I have problems connecting to a security camera FLIR FX at the network.

  For your specific problem of FLIR FX, FLIR FX support should give you the best information on how to operate with your systemof their product .

  Post edited by: Jim EZ

  Mac OSX 10.11.2

• How can I limit the number of connections to my PC for an incoming connection at a time. Multiple users are connected to my computer via the network.

  original title: limit incoming connections

  I want to restrict the number of connections to my pc for an incoming connection at a time.  I have several users that connect to my computer, using the same user name & password.  If someone tries to open a session, they fall out of someone who is already connected, without notice. the only solution I can think of is to limit the number of incoming connections to one.

  Hi willard.

  Your question is more complex that most seem to be on the answers. I suggest that you re-post on our TechNetforums where computer professionals can help you.

  http://social.technet.Microsoft.com/forums/en-us/categories/

  I hope this helps.

• I installed a new router. Now, one of the PC will not allow the rest of the pc s are there to connect. He is able to connect to each computer on the network. I can't find the question, any help?

  I have checked the computer name, sharing, turned off the firewall.  Still can't find the question.

  I've corrected in fact accidentally the problem today.  I uninstalled a Malware program and tada!, the other pc on the network were immediately able to access the XP pc.  The 'good' pc was always able to access internet, router, network between them.  The only problem we had was the 'bad' pc was able to connect at all, but the 'good' pc were unable to connect to the computer of 'bad '.

• WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network

  I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you

  Firewalls are disabled on remote computers?

• To connect to other computers on the network

  Is it possible to connect to other computers on my network through the slate of 7 (laptop)?

  Can take a look at Splashtop2 in the game store.  Worked great in webOS, should be just as good in Android.

  WyreNut

• Unable to connect to Xbox 360 via the network.

  Original title: network host down

  OK, so I have my xbox 360 and a laptop of HP under win7 set up on my home network to my dell PC winVISTA.  One day the network just stopped working no real reason.  The xbox and the laptop can connent to the internet but do not communicate with each other.  Pls help and nothing changed just, it stopped working.  The xbox is my media hub and my laptop for work, this is all very frustrating.  Thnx in advance for any help.

  Hello

  1 have you made changes to your computer recently?

  2. what happens when you try to connect between computer and Xbox 360?

  I suggest you follow the methods and check if it helps.

  Method 1: Follow the link below and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Method 2: Links and check if it helps.

  Xbox LIVE connection problems
  
  http://support.Xbox.com/en-us/pages/Xbox-Live/troubleshoot/connection-issues/connect-Xbox-Live.aspx
   
   
  Error: Unable to connect to your wireless network
  
  http://support.Xbox.com/en-us/pages/Xbox-360/troubleshoot/KB/error-cant-connect-wireless-network.aspx?kbid=978945
   
   
  Xbox LIVE connection errors troubleshooting
  
  http://support.Xbox.com/en-us/pages/Xbox-Live/troubleshoot/connection-issues/errors.aspx
   

• Unable to remote connect to another computer on the network home

  Greetings,

  I have a Windows 7 desktop computer and a laptop Windows Vista Edition full.  I am able to connect using the program of remote connection to the laptop from the desktop, but not the laptop on the desk.  I get
  an error that says "Remote Desktop disconnected' and inside the box, he says" this computer can't remote not connect "and communicate with the administrator, me.

  I turn off the Norton firewall on the desktop and no luck.  I typed the IP address and the name of the desktop computer.  Both get the same answer.  I ping the desktop from the laptop.

  Any suggestions?

  Hello
   
  1. which is the edition of Windows 7 is installed on the desktop?
   
  We recommend that you first of all to you allows to cross check if remote desktop connection settings are correct on the Windows 7 computer. To do this, follow these steps.
  1. Click Start, right-click computer and click Properties.
  2. in the left pane, click Remote settings.
  3. in the System Properties window, click use remotely.
  4. make sure that the following settings are applied.
  a. allow for Assistance connections to this computer remotely.
  b. the remote desktop section, select "allow the connection of computers running any version of remote desktop (less safe).
  5. apply the settings.
  6. restart the computer and try to connect to the remote computer.
  
  For more help on desktop connection remotely, see this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Remote-Desktop-problems
  For more information about remote desktop, see this link:
  http://Windows.Microsoft.com/en-us/Windows7/Remote-Desktop-connection-frequently-asked-questions
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Vista can connect to other computers on the network, but not to the internet

  I have a Vista computer that I just reinstalled and it is connected through a router Thomson to a Win7 machine and internet (or at least it should be).  For some reason any Vista machine refers to the network as a public network that I can change this private and turn on discovery.  If I do that, then the machine Vista can see the Win7 machine through the router, but cannot connect to the internet.

  I tried to use the disk driver for the Thomson router on the Vista machine, but at the time wherever he tells me to connect cable internet installation program does not detect that the cable has been connected.

  Troubleshooting with software Vista suggests simply reboot the router (that I tried without success).  Needless to say that the Win7 machine connects to the internet fine.

  I was wondering whether to try to remove the connection and start again, but unable to do so because when the cable is plugged in tells me you cannot delete an active connection and when I disconnect the cable network connection disappears and so cannot be deleted.

  Grateful for pointers

  Ian

  Hi IanRC,

  Try the following steps.

  Step 1

  You can try to disable the antivirus software on your computer and check if it works. Activate antivirus once you check the status.

  Note An antivirus program is designed to help protect your computer against viruses. You must not download or open files from sources that you do not have trust, visit Web sites that do not trust, or open attachments when your antivirus program is disabled.

  Step 2

  Try the Microsoft Fixit. Open the link below and click it on the Fixit button.

  http://support.Microsoft.com/kb/928233

  Check if it works and post back the result.

  Bindu S -Microsoft Support
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• What password is required for connectivity to my wifes on the network computer?

  Of my wife and my machine is connected to the router Ethernet.  I get this message and have no idea at this stage what password is requested.  She uses Win 10 and I am on Win 7.  internet connection issue basic I know but I'm not aware at all on these issues.  Thank you.

  cannot post a picture here is so going to try describe the message.

  up: enter the network password

  the following line: "enter your password to connect with: MOM.

  Then the box: my computer name and the name given to the router

  the next area: request password

  the next box: "use another account.

  I tried every password I have for the system and computers with no luck. both machines are identified as being a "home network" with all the options set to 'on' password sharing and selected 'Off '.   any ideas?  Thank you

  To remove the network password, you must change the settings where the network was setup. To do this, connect your PC to 10 Windows and follow the steps below:

  1. Open the Control Panel.
  2. Click network and Internet.
  3. Click network and sharing Center and change advanced sharing settings.
  4. Click on all the networks and scroll down to password protected sharing to change the setting.

  

  Let us know how it went.