HP LaserJet 400 M401dn

Similar Questions

• LaserJet 400 m401dn: HP Laserjet 400 m401dn, make wireless?

  Is it possible to buy a product to make the Laserjet 400 m401dn active wifi or is this product already activated?  The internet router is in another place, so a physical connection is not possible.  I would like the capability configure the SSID, etc. to connect and print.  Thank you.

  > Laserjet 400 m401dn wifi active or is this product already activated?

  The m401dn is a model of printer Dmodel Network (wire) connected.  The active WiFi model would be a M401dw , that would be the model Dand Wwireless.

  However, if you create a connection to your router via a wired Ethernet connection and then the printer would be accessible by wireless network devices.  All you need to do is get the printer on the network.

  > internet router is in a different location so a physical connection is not possible.

  The only options you have are to run a new cable at the location of the printer and Ethernet cable connect with the current hardware.

  Otherwise you would seek to create a 'bridge' between the printer and the router wireless network using a router without wire 2.  Configure the wireless router 2 to act as a client or to fill in the primary wireless router that acts as the main Point of access to the network.  Once the 2nd wireless router is filled in elementary school all the devices that are connected to Router 2 will be accessible from the main access point.

  There are guides out there circulating that walks you through this process, but the specific steps will have to come some 2nd router manufacturer, you can decide to experiment.

  Here is a sample of Cisco support article that calls this "Cascade" procedure one router to another:

  http://www.Cisco.com/c/en/us/support/docs/voice-unified-communications/SPA8000-8-port-IP-telephony-gateway/108678-PQA-108678.html

• HP Laserjet 400 M401dn: M401dn Firmware - print issues

  Hello.

  We have 4 HP Laserjet M401dn printers 400 in school.  These have been delivered and installed in time last September.

  A problem highlighted recently when one of the teachers tried to print a simple Word document with a title in large font.  Whenever they printed the document, pages with the large font size came out white.

  We tried new documents and other things, but whenever we have changed the size of the police to more than 70pt, the page would come out blank.

  We then tested the same documents on other printers and it printed perfectly on 2 of the 3.

  The 3rd company of the party in charge of our network took a look at the problem and it's associated Firmware.

  PE / printer of geography are the two stamped Date of 20140521 Firmware.  Two of these printers cannot print fonts of size greater than 70pt.

  Staff room printer was Date stamped 20120907 Firmware and prints ok.

  ICT after the Date stamped printer Firmware of 20131214 and prints ok.

  Can you HP and other users of this particular model, please test?  If the results are the same, HP can please release a updated Firmware to fix the problem?

  If this isn't the case, please tell me where can I find previous versions of the firmware and the utility to restore the affected printers 2?

  Thank you very much.

  Hello.

  Thank you for the answers.

  I sent the following link for an update of Firmware for May 5, 2015 that solved the printing problem.

  HP 20150410 firmware

• HP LaserJet 400 M401dn: M401dn not print white text on a black background

  Hello

  We do not print white text on a blackground on a M401dn. I am trying to print a Word document. Prints fine on other printers we have - Brother HL-2240dn, Ricoh Aficio C4501.

  When the work is submitted the HP printer prints a black block. There is no white text.

  Can someone help me solve this problem please?

  Thank you.

  After reviewing your samples in detail a bit more, I suspect that the problem may be associated with the size of the font you are selection (so it would affect black text on white background) rather than being something to do with the colors of text and background.

  With a number of recent models LaserJet Mnnn , a firmware issue has prevented use of the font with a size of 72 points or more.

  These appear to have been fixed with a new version of the firmware - see http://h30434.www3.hp.com/t5/Printer-All-in-One-Software-Drivers/M401dn-Firmware-Printing-issues/m-p/5008912

• LaserJet 400 M401dn: LaserJet 400 M401dn no two-way Communication

  The box to check the two-way Communication is grayed out and not verified.  We use FM Audit and officers on local printers installed for the counters and toner provide alerts and need this feature.  All PC use the right HP driver for this model, version unknown.  All agents do not report the levels of supply or meters.

  Support FMA suggested using a universal print driver, which we did.  We can now check for two-way Communication and receive meters, but still no power levels.

  Thanks for the comments.  After many trips on the clients site for FM Audit report meter/supply levels, finally informed me their tech support my model HP so that countless others report not correctly if at all when a local USB connection is used.  Here is a link to the models and how they report, or not in my case.

  FTP://FTP.fmaudit.com/customer/documents/Device_Compatibility_2016.PDF

• HP Laserjet 400 M401dn: HP Laserjet 400 M401dn is not recognized as a printer.

  We have one of these printers, and the user plugged into their PC before that we loaded the drivers.  Now the PC sees the printer as an external storage device.  Even when we try to load the complete drivers and connect us the printer to the USB port when the installation process is said to connect the printer that it distillers immediately sees it as a storage device and will not complete the installation.  We have tried to do the same process with a different USB port, but no luck.  We tried to go through the registry and remove all references to a printer M401 but that did not help.  What can we do to fix this?  Thank you

  Thanks for the reply... what I ended up doing was in the settings in the Panel, I turned off the Smart Install feature and then after a reboot of the PC, I was able to install the printer drivers and everything works now.

• RESOLVED - "49 error turn off then" HP LaserJet 400 M451dn

  Last week, I set up not one but 2 printers HP LaserJet 400 M451dn color for a client. It was 2 because I went first to the provider think there is a fault with the printer showed a 49 error randomly, but when I got exactly the same error on the 2nd and the same printer with a different provider, I thought that this may not be the case.

  What I found was - I set up the printer with a static IP address of 192.168.0.218 and excluded this address in the DHCP reservation list, so it is not assigned to another device. If I turned on the printer without the LAN cable connected the printer would say "Ready", but as soon as I connected the LAN cable, it is when that would throw a wobbly and appear "error 49 - Turn off, then on. I tried to reset the default printer without joy.

  THE FIX here IS (or should I say a work around) in the following order:

  (1) remove the LAN / network printer cables.

  (2) to reset the default printer.

  (3) remove the the 192.168.0.218 of the server DHCP reservation.

  (4) delete the IP 192.168.0.218 Server lease.

  (5) connect the LAN cable to the printer.

  (6) can get a new IP address from the printer. Using the same IP address again you go back to step 1 again.

  (7) that's all.

  For some reason, this printer does NOT set a static IP address and put a reserve on the server. Nuts!

  I installed several HP printers that I have in the course of the years and never encountered this problem. As I mentioned above, this is more than a solution to a genuine problem...

  Hope you guys find this post useful.

  I had exactly the same problem with a M451dn of 400 LaserJet, except in a working group with the router making DHCP, use a static address outside DHCP for 2 days and then pool this week had error 49, noticed that when the Lan cable has been disconnected, he seems to have stopped. Printer changed to use DHCP and it works again. (updating the firmware via USB had no effect)

• HP LaserJet 400 colorMFP M475dw scan to E-mail problems

  Hi all!

  I would appreciate a solution to my agony.

  We recently purchased a printer HP LaserJet 400 colorMFP M475dw. Now, I'm putting in place (browser-> Scan--> the outgoing message profile administration) to send scanworks by e-mail but face the following problems:

  1. when it is correctly typed all the credentials, even the "Test & Save" option takes forever. After cople attempts I got it successfully tested.

  2. with the help of my personal gmail accout as the sender, sweeping work takes a lot of time. It stops in the phase connection smtp server for quite a long time before even starting the actual analysis.

  3 using the company newly created accounts of e-mail as a sender, it takes even more time. I timed it just 6 minutes and 23 seconds before the actual analysis.

  4. now, it seems to send the scan ok, but with some first attempts it failed with some general error message asking to try again.

  In my opinion, the time it takes is completely unacceptable. Is this a known problem and is there a workaround?

  Our company emails run on MS Office 365 and I use smtp.office365.com as server smtp port 587 and SSL/TLS ticked (tried also unchecked). As I said with Gmail, it would also slow but still very very very slow.

  Help, please?

  I know this is an old thread, but just in case anyone is still having problems with this - I managed to fix it by disabling IPv6 in network-> advanced in the web server administrator. Connect to smtp.gmail.com from 3 minutes + seconds.

• HP laserjet 400: hp laserjet 400

  Whenever I have install new ink cartridges, he throws the alignment off the coast. It's like it prints twice, especially in color.

  It makes it almost impossible to read. I'm tired of paying a technician to fix this, every month. Help!

  HP LaserJet 400 color MFP M475fn

  Calibrate the product from the control panel
  1. press the Setup button.
  2. open the configuration menu of the system.
  3 open the print quality menu.
  4. open the menu of color calibration.
  5. tap the element calibrate now.

• HP LaserJet 400 ColorMFP M475D: HP equipment MIB (Management Information Base)

  Hello!

  I am developing a project with Zabbix (open source solution for the network, applications, and devices, such as a printer, switch and monitoring etc) and now I'm getting better the SNMP Protocol on this software. So, to start, I need to know some information in one of my devices, in this case a HP LaserJet 400 ColorMFP M475DN.

  Could someone tell me how CAN I find the MIB (Management Information Base) and the OID (Object Identifier) of this equipment?

  Thank you!

  Navigate to the developer https://spp.itcs.hp.com/spp/ Web site

  From the home page (via the button in the Software Development Kit ), it is possible to access the package public spaces:

  

  Within the branch Laserjet and Digital Sender , select management of printers. MIB | MIBs Phoenix device, and you'll find a relevant entry for your device:

  

• Printing to HP Laserjet 400 M401N corrupt characters

  I just installed a new HP Laserjet 400 M401N and his corrupt characters printing. This often happens when I print pdf files.

  I ran the scrubber and reinstalled the drivers again, but it still does the same thing. Help, please. Thank you.

  The solution was to use a universal driver.

  Here are the XP x 86 one:

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=5096252&prodNameId=5166603&swEnvOID=228&swLang=8&mode=2&taskId=135&swItem=ds-99375-4

  It is here is Windows 7 64 bit one:

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=5096252&prodNameId=5166603&swEnvOID=4063&swLang=8&mode=2&taskId=135&swItem=ds-99376-4

• LaserJet 400 M451dn: laserjet 400

  I have a printer LaserJet 400 M451dn . There was a severe storm, but the printer is on a surge protector APC, including a printer HP LaserJet P1501n and other devices. All other devices operate normally.

  The LaserJet 400 M451dn printer when turned on, the symptoms are the following:

  • Noise of rattling all 4.5 sec
  • White LCD screen
  • no lights on the front panel
  • Ping address responds 'host unreachable '.
  • On printer Ethernet port are turned on

  Printer is on a network, local domestic and no software change or recent driver.

  I tried HP solutions but without success.

  Any suggestion is appreciated.

  ~ Pheeoo

  Hello @Pheeoo

  Think about replacement parts this its go device but you only have two options

  To display sound problem usually a combo that you need to get the trainer + Control Panel from one of the 2 could be the problem

  HP part dept store number its 800 227 8164

  The other option will be to return this printer for a discount for another product

  HP 888 447 0078 ext 813 solutions

  You can call them and see what they have to offer with this second option

• 400 LaserJet (M401): HP Laserjet 400 Networking Question

  We have a HP Laserjet 400 that is connected to a wired network. We also have a point of wireless access on the same network. When an ethernet cable is connected to the printer (in a perfect world), the wireless tap stop to avoid conflicts, BUT about 20 minutes of pluging in an ethernet cable, the wireless access point goes down (no longer works and must be restarted).  This isn't the only one who did this access point. The printer has caused to the whole of the network thus go down (5 servers & 40 + workstations). This printer did not do that when we got it (a year ago). Anyone has any suggestions for me doesnot involve making wirless only or replacement of the acess points (for the 3rd time)?

  Thanks in advance,

  Dan

  Huumm... do not know how this can happen.   However, manually turn off the Radio wireless in the printer.  If the printer supports Direct wireless, make sure that this is also disabled.

• Many vertical lines colored on the second side of ADF scanner on HP LaserJet 400 MFP M425dn

  When I scan using the ADF on our MFP HP LaserJet 400 in mode '2-sided' M425dn, the back side of the scans (even-numbered pages in the PDF file) is wiped out by a good number of colored vertical lines. (see attachment)

  I tried to clean the ADF scanning window, but I do not think that these lines are caused by dirt or debris .

  Thank you!

  Ben

  There is a notice for this defect, as such I would say contact you HP warranty - there are a few steps to be taken to eliminate and recalibrate the scanner, if the problem persists then it is a module of formatting of replacement and recalibration is needed.

• HP LaserJet 400 ColorMFP M475D: Where I found the Documentation MIB?

  Hello!

  I'm trying to monitor a printer, a HP LaserJet 400 ColorMFP M475D and to move forward with what I need device MIB. Thus, the HP Forum help me with this information in the last month in this thread.

  But, MIB has a lot of information and I don't know what they mean. This type of file have a documentation? I just found the MIB repository, but they documentation I don't know.

  Could someone answer if it have a documentation?

  Thank you!

  The format of MIB data (for printers and other devices) follow a set of standards that is not defined by HP.

  A basic description of the MIBs print shops can be found in this document RFC 3085.

  It is not easy to read (don't expect any specification document to be).

  There are probably many applications available to help interpret the MIBs and how to use them with SNMP functions.

  It is not something I know a lot of things, so I can't recommend specific applications.