HP LaserJet Pro 400 M401dn: Printer setup error

Similar Questions

• HP LaserJet Pro 400 M401dn: Printer PCL XL Error

  Hi all
  
  I am help out at school and class times year book are coming and the aret students print their drafts. but when printing from Adobe indesign CS5 is the error we get:
  
  Error X PCL

  Subsystem: TEXT

  Error: InternalError 0 x 50

  File name: Cheettext. c

  Line number: 710

  I am brand new to all this, so any advice would be great! Thank you!

  Hello

  You can try putting the printer off, unplug the cord of her power and wait 30 seconds.  Plugged in, it works.

  Hope it will solve your problem.

  Good impression

• LaserJet Pro 400 M401dn - 79 SERVICE ERROR

  We didn't have this printer less than a year and I'm getting an ERROR of SERVICE 79.  I recycled power unplugged and all normal try... no go.  It prints the menu card, but will not accept a print job from a user.

  I try to get out of the printer on HP.com page but it errors so I can't one of support for the model documentation.  Anyone out there have a suggestion?

  Hi all
  I found and you want to share one of the cause of the error in my network. It is caused by the printing process unsuccessful of one or more computers on the network. I could have corrected the error 79 by following a few steps.
  1. turned off the printer
  2. check and remove the printing process of all the computers that can access the printer on the network.
  3. in the domain network, you cannot cancel the verification of the printing process the owner in the box of "see what's printing.
  4. then log on with this account and try to remove
  5. If you can not even cancel the printing process, you must remove and re-add the printer.

  After you complete these steps on each computer, but have access to the printer in the network, you can turn on the printer, and it should work well.

• laserJet Pro 400 color: printer

  Hello Mr President
  I want a help on your part I have a Color LaserJet Pro 400 m475dw MFP
  and when I turned it on. I show masseage like this {10.1002 electric memory error}
  How can I solve this problem, Mr President

  Hello Sir,

  The error that you expose is a problem with one of the toners.
  The magenta to be precise.
  
  In this case, the recommended action is to replace the magenta toner with an original RESUME.
  
  Kind regards

• HP LaserJet Pro 400 m401dne: print from Notepad

  Hello! I have a new HP LaserJet Pro 400 m401dne. Everything works fine except when I try to print both sides of a Notepad document copies. As soon as I select the duplex option, the entire document disappears. We had an another HP LaserJet only printed on one side of the paper; who would have something to do with it? Still, I have this printer on the printer list but am selecting a new. I can print any other documents on 2 sides; just don't leave the notebook. Thanks for any help you can give me!

  Thank you, HP! The warranty issue has been resolved and so was the two-sided printing problem. The technician had to install Universal printing and now I can print copies front and back of notebook and everywhere else.  )

• Help! My M475dn MFP HP LaserJet Pro 400 color printer will NOT print!

  HP LaserJet Pro 400 color MFP-M475dn-CE863A

  Printer on a network and can connect to multiple computers that include: Mac OS X, Windows 7 and Windows XP.

  When I try to print from my iMac, the print queue of the printer says "the printer is not connected.  When we try to print from Windows computers, it is in the right queue and does not print.  When I go the printer itself and try to print a page of demonstration or page supplies directly to him, it says on the screen which is printed, but nothing happens.  This is not hum or anything!  The port where the network cable is connected is switched on green that says HP which means that the network cable is connected.  We've had this printer for a year now, and something like that never happened.

  I did not have any software or anything like that until this happened.  It was working fine on Saturday when we used it, but when we arrived at work today, he just decided that it would interrupt printing!

  I'm puzzled!  I tried 'ping' IP address of the printer from my iMac and it pings fine.  Does anyone have advice?

  (I tried to make of the obvious like too switch the printer on and off and shutting the computer down and nothing!)

  Okay, so I feel a bit stupid right now.  I decided that I would be closed the printer for about an hour to see if it was there, and what you know-it has been!  I had to turn it off several times before but I guess it wasn't long enough.  What a pain!

  Thanks to everyone who took the time to read this!  Sorry to waste time everyone!

• LaserJet pro 400 m451nw - Print is too dark

  I have a LaserJet Pro 400 M451nw color, and every time I print any type of blue, it prints really dark.  Tonight, the blue on my monitor was a royal blue, and blue printed was almost black. I reduced the blue on the graph, but it's still not royal blue.  The program I use is MS Publisher 2013.

  Is it possible for me to adjust the parameters of the cyan cartridge, so it will not print so dark?

  Thank you

  SHJ

  Hello ayligcjdesign,

  Welcome to the HP Forums.

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do it at Business Forum.

  Thank you for your time.

• HP Laserjet Pro 400 color M451nw - formidable error 79; Turn on/off.

  By HevnLgh; Asked me to this post in the trade forum.

  I scoured the internet to find a solution to my problem and I can't find an answer for her.

  Error 79 came in our printer last week and has not recovered since.

  Here are the solutions I have tried or attempted to have tried:

  • Soft Reset - it turn off and save
  • Hard Reset - unplug the power cord for 60 seconds or more and in him plugging back in
  • Do the above AND have the network cable unplugged everything by
  • Tried to update the firmware. Cannot. The printer makes a loop in a ready state in error 79. When you try to connect using a usb cable to update, windows can't detect the printer during the loop it is in error 79.

  Any ideas?

  Thanks in advance.

  If you turn the printer off, unplug the network cable and only connected on power and then turn on and you get the error 79, then the trainer is toast and needs to be replaced. If on the other hand with the network cable disconnected it is loan and only goes to the error 79 when the network cable is connected, then that would mean you have a bad job in the system tries to print whenever the printer talks to the network and you must remove the computer or server.

• LaserJet Pro 400 (M401dn) paper jams of all trays

  Our Organization has just bought a M401dn brand new, and I've been setting up out of the box. After you have configured the IP, I went to print a report. The jams from tray 2 with the message "paper jam in cartridge area. Open door and clear jam'.» I've therefore allowed and did it again. All to nothing does not; It keeps blocking. I tried to print from Tray 1 and it's the same thing; the paper is folded in almost a concertina-style and not powered through.

  I put the correct paper (letter) in the printer sizes, updated its firmware, checked to see if there was that whatever it is hung in the transport of paper (not there), and I'm out of ideas. The weight of the paper I use is 20 lb (75 g/m2), which should not cause problems with transport.

  We bought three M401n before, and they were easy to set up. So far, I am very far from impressed by the M401dn. Any suggestions / ideas would be gratefully received.

  My first question is how recently where the unit was purchased, and you have contacted the helpline? On most hardware problems, it is best to contact phone support directly so that they can offer better, more immediate help, and they have the power to replace the unit in some cases, if necessary.

  Aside from that, you were sure to check the internal parts of the machine for anything whether on-site or any debris

  Let me know!

  -Spencer

  PS I hope you have a wonderful day!

• Drivers for HP LaserJet Pro 400 M401dne printer

  Hello

  Product page: http://store.hp.com/UKStore/Merch/Product.aspx?id=CF399A&opt=B19&sel=BPRN

  I bought this printer, so it can be shared among a group of approximately 5 members of staff. I usually download and store drivers for printers etc. on the network and install from there but am unable to find any sort of link from where I can download the drivers 32/64 bits for this product.

  I need to specific drivers, not the UPD. The UPD is very good for the generic print jobs, but does not work with certain software.

  Whenever I try to find a driver for this device links form a circle and just send you back with the same pages.

  I am from this page:

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdHome?sp4ts.Oid=5307051&AC.adm...

  Can someone provide a link to the 32 and 64 bit Windows drivers for this product, please?

  Thank you!

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do it at Business Forum.

  Best wishes!

• Laser Jet Pro 400 M401dn: printer is currently not connected after a move

  Last week, before moved me home, everything was fine with my printer and the iMac.  After my move and install my printer as usual (with the USB WIFI connector not) I can't print.  The message that appears is that 'the printer is not connected""print - the printer is offline.

  Please HELP - what should I do - I wish I could talk to someone directly...

  Yes I did

• Color LaserJet Pro 400 M451dn: Print vs wireless network

  I used my printer Wireless Ethernet connection between printer and Apple airport base station. I am moving and can use printer wireless without direct connection to the router? (Printer & new router in place will be not near each other for the direct cable connection is not convenient). Thank you!

  Hello @Cary2

  No way, it's a D M451dn stands for double-sided N to the network (wired network), only the M451dw will have the possibility of having the wireless

  The printer must have a wired network to the internet permanently connection

• HP LaserJet Pro 400 M401dne print only one page (document)

  
  

  Solved.
  Next to status of control over the PCL6 drivers (probably wants new firmware).

  Makes office 2013 - Win 7 x 86 and x 64, x 86 Win8 (I test on a clean install of Win - after install Office 2013's back problem)

  Fu * k

• LaserJet pro 400 m425dn mfp: mfp laserjet pro 400 m425dn will not connect to the network

  I just bought a mfp laserjet pro 400 m425dn printer/phtocopier and I can't seem to connect to our network.  I have it plugged into the router and it says "cable disconnected" without an IP address.  I don't have the USB cable to configure the machine and I was hoping to do it via the network (which tells me is an option).  I don't know if that has something to do with it.

  Any help would be greatly appreciated.

  The printer should be released the box set up using DHCP for addressing.

  When plug you it into the router it should pull an IP address, if it is its cable disconnected then you might have a bad port on the router, a bad cable or a bad printer.

  Plug something else into the same port with the same cable and see if it works, if you have a defective printer and need to return it and get a replacement.

  You may also be able to find someone to replace the trainer who has the network port to it.

  If my post is solved your problem and click the accepted as button solution under him.

  In order to thank a Tech for a post click the thumbs up button under the post.

  You can even click on the two keys...

• Lost password - M401 of printer HP LaserJet Pro 400 series

  Hi all

  We have a years M401 of printer HP LaserJet Pro 400 series(touch screen model), a fo our former employee requested a password. Nobody knows this password and need to change the IP address of the printer.

  I'm looking to do a factory reset. What I found on the user guide, the procedure would be:

  Restore the default values set in the factory (touch panel)
  1. from the home screen on the product control panel, press the Setup button.
  2. highlight and press the Service menu.
  3. highlight and press the default button and then press the OK button.
  The product automatically restarts.

  The problem is that when I touch "service" menu, the password prompt prevents me from going to the next menu. Is there another way to do a factory reset on this printer? A button physics somewere? Something to do with the power button may be?

  Thank you very much for your help!

  Oliver

  I found how do:

  After a the NVRAM initialization, reconfigure all computers that print to this product so that the computer can recognize the product.