HP LaserJet Pro M402-M403 n - dn: Tonar question series n - dn HP LaserJet Pro M402-M403

It has supported toner is 26A, any other printer toner with product? or 26A toner can be used which printers?

I understand that for the series of products M402 toner cartridges and M403 is different (26 and 28A respectively).

You may find it useful to understand the compatible products according to the guidelines of your query for HP 26 a toner cartrdige HP web links to the address below:

http://WWW8.HP.com/emea_africa/en/products/OAS/product-detail.html?OID=8629610#! tab = compatible_hosts

http://support.HP.com/in-en/document/c04798381

I hope this helps!

Tags: HP Printers

Similar Questions

  • Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

    Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

    I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

    I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

    I had care of do not connect USB until you are educated.

    I tried repeating the installation without uninstalling first and get the same result.

    I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

    I tried to do a right click to run the installer as administrator and get the same result.

    I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

    The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

    I tried to connect via USB 2.0 and 3.0 ports.

    I cleaned recycle them and temporary folders.

    I have updated the firmware of the printer to the 20160331 version.

    Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

    I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

    Thanks for any help solving this.

    I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

    DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

    1. go into the Device Manager and find the printer in the list of devices

    2. right click on the printer and select "Update Driver software"

    3. click on "Browse my computer for driver software".

    4. choose "Let Me pick one...» »

    5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

    6. click next and back to the installation of hp box and must now see the printer and continue the installation.

    -Alex

  • I get a pcl xl error message when we print our LaserJet Pro 400 Color MFP

    When I scan or fax, we get:

    PCL XL Error

    Subsystem: TEXT

    Error: InternalError 0 x 50

    File name: cheettext.c

    Line number: 710

    The printer is a Pro 400 Color MFP LaserJet - m475dw

    Windows 7 Professional Service pack 1

    What should I do to fix this?

    Thanks for the help.  I actually did an update of the firmware and it solved the problem.

  • Unsupported personality: PCL on print Laserjet 1012 from Windows 7 Pro 64-bit

    I have an HP Laserjet 1012.  My PC has Windows 7 Pro 64 bit.  I used the Laserjet 1015 PCL 6 drivers.  When I printed the first two times, it worked fine.  Now each page just print "Unsupported personality: PCL ' at the top.

    What should I do now?

    Thank you for your ' Experts for a day Tech Support.

    Mark

    Hi rbarbo43,

    I found the following thread that will help you during the installation of the printer in Windows 7. Let me know if you need assistance?

    http://h30434.www3.HP.com/T5/printer-networking-and-wireless/LaserJet-1012-driver-for-Windows-7/m-p/351356#M16114

  • M127fn LaserJet MFP Pro: Hp Laserjet help


    https://h30434.www3.HP.com/T5/LaserJet-printing/HP-LaserJet-Pro-MFP-M127fn-beep/m-p/5099750

  • LaserJet pro 177: bought used hp color laserjet pro mfp m177

    Installation disk arived broken. How can I do to replace it.

    Just upload what you want the site web theHP.

    http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

  • Color LaserJet MFP Pro 277dw: MFP will print but not scan since update Mac OS 10.10.5

    I had used my LaserJet MFP Pro wireless without problem for several years, with the Mavericks and Yosemite.  A few weeks ago a "update" the printer system is invisible.  After several hours of troubleshooting and to try five or six corrections, I finally got the printer online by using the IP address.

    My computers, however (a performer of the Mavericks and a Yosemite running), do not see the scanner.  It's not a question of adding - they do not to add it.  By HP support, I have reset the system print and tried to start over.  I downloaded HP Easy Print (or Easy Start or whatever), which is the entire site of support in the way of software for the 277dw of the ACM.  The software through me the entire upward and congratulated himself for a job well done, but my printer was not, in fact, related.  He appeared in the printers Control Panel, but would not print.  Just "connecting to printer" in the queue for ten minutes about until what I called off work.  And the scanner does not yet show in the Image Capture, preview or HP Easy Scan.

    So, I went back to my previous fix for the printer, use the IP address.  Any ideas on how to get the scanner appears?

    Hello

    Restart your router by unplugging its power for 30 seconds.

    Once it is fully up and you have internet access on your Mac reboot both the HP printer and the Mac.

    From system preferences, select Printers and scanners and click on the plus sign to add the printer again.

    Can you now ee he listed as Hello type or not?

  • LaserJet Pro M201dw: Remove the LaserJet Pro M201dw of ePrintCenter

    I bought a printer LaserJet Pro M201dw I have installed the printer. I registered it to ePrintCenter.

    The next day, I had to return the printer for a refund. However, I did not remove the ePrintCenter printer (disable Web Services) before I returned it.

    How can I remove the printer from my ePrintCenter?

    Your help is appreciated.

    Hello

    Please sign in to your connected HP account:

    https://www.hpconnected.com/us/en/#devices/

    Select the one you want to delete, click settings, and then click on delete a printer (right side)

    Kind regards.

  • Add networked LaserJet Pro 200 to ePrint

    I can't add my new Color LaserJet Pro 200 M251nw networked to ePrint.  When I try to follow the iPad on the orientation of the screen, after entering the printers IP address he wants then connect to Enterprise ePrint.  I don't have it.

    My older inkjet has been on ePrint, no problem.  Help, please.

    Hello
    You try to use the HP ePrint Mobile's application or e-mail ePrint service?

    If you try to start with the email ePrint service, take a look to the following document:
    http://h30434.www3.HP.com/T5/user/viewprofilepage/user-ID/2585903

    If you try to use the HP ePrint on your iPad app, I would recommend a look at the following document:
    http://support.HP.com/us-en/document/c01616126

  • HP Color LaserJet Pro M177 MFP: HP Color LaserJet not able to connect to connected HP

    Hello

    I try to activate my printer (HP Color LaserJet M177fw MFP Pro) ePrint and much more, but I'm not able to do it cause connection problem, I guess.

    When I'm trying to 'print the information sheet', for example, the printer is not able to connect (stay on 'Sign in' loop indefinitely).

    My printer is less than a Vodafone EasyBox router, with firewall disabled and no specific barriers defined by me.

    Should I set some port forwarding (even if they should apply to ignore the firewall, when turned on) or any other specific configuration in the router?

    the same connection problem, of course, it happens when I do touch printer and console web administration, of course.

    In addition, I'll let you know that my router is not blocking access, for example, to-from the web (i.e. I am able to manage my NAS from the outside, since he admitted to a DDNS) and other local devices

    I alreay set 8.8.8.8 and 8.8.4.4 as DNS pri/sec and had an output of cycle after the series of DNS.

    My printer also has a static IP address (defined by the DHCP protocol, based on the MAC address), so not a problem, I think.

    Thanks in advance for your help,

    Lorenzo

    Hi Lorenzo,.

    To enable Web Services fumctionality, you'll need to install the latest firmware on your printer (version 20160525)

    You can locate the current version of your printer by selecting configuration > reports > Page of Configuration, the firmware version is listed under the information section on the printer.

    Updated the firmware on Linux by following these steps, but I don't know if the latest firmware is available for Linux or not, try:

    http://hplipopensource.com/hplip-Web/tech_docs/man_pages/firmware.html

    If the latest firmware is not available for linux, temporarily install the printer on a Windows PC or a my and install the latest firmware:

    http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

    Kind regards

    Shlomi

  • Color LaserJet MFP M177fw Pro: installation of web services blocked to 'connection '.

    I'm trying to enable Web Services on this new LaserJet.  I am in the built-in Web Server page and the configuration of Web Services tab.  I clicked on 'Turn on' and it just keeps spinning in connection...

    DNS is 8888 and 8844

    All the other tabs work; It is connected to the computer and the Internet.  Help please?

    Thank you!

    Hi @crowndude,

    I see that you have problems with Web Services. I want to help you.

    I have provided a few steps to try to see if we can solve this problem.

    Turn off IPv6 on the printer.

    Go to configuration, network configuration, network, IPv6 Services and turn it off.

    This DNS works better for Laserjet printers. Please change the settings to see if this will help the printer built-in Web server.

    Preferred DNS address: 209.244.0.3
    Auxiliary DNS address: 209.244.0.4

    Power cycle the printer.

    If you still have questions, please continue with the following steps:

    Update the firmware of the printer by a USB connection. HP Color LaserJet Pro MFP Firmware update M177fw.

    Configure a static IP address for the printer. Proceed to Solution 3: printer of the assign a static IP address.

    Printer HP Color LaserJet Pro MFP M177fw and HP LaserJet Pro MFP M127fw and M128fw printers - printer does not keep the Wi - Fi connection.

    I'll send you another step to try in a private message.
    In the forum next to your handle name simply click on the envelope to see.

    If you appreciate my efforts, please click on the "Thumbs up" button below.

    If there is anything else I can help you, let me know. Thank you.

  • MFP HP LaserJet Pro 400 M425dn cold reset

    Hello!

    Help me! How can I make cold reset HP LaserJet Pro 400 MFP M425dn ?

    You can do 'factory reset' menu of the control panel; or permanent initialization of power first, holding and cover the corner area to the right / left of the control panel when you feed on... release your finger when you see «initialization permanent...» ». After you complete and return the loan, it indicates the reset is complete.

  • LaserJet Pro 200 m251nw: how to disable these pages printing pesky notification?

    I just bought the LaserJet Pro 200 m251nw to help with homeschooling and coupon printing. A big HUGE machine so far, one small complaint... whenever I have do something or something (ie: plan a printout of the spreadsheet on an app) Springs this page full color printing. I don't want to lose my ink telling me I just do what I know already! Can I disable it somehow? Thanks in advance!

    Hi @g33kyg1rl

    Welcome to the Forums of HP's Support.  I see you want to learn how to turn off notifications in HP connected for your Laserjet M251nw printer.

    Please follow the steps listed below:

    1. Connect to your HP account connected, which will take you to the Welcome screen.

    2. Please click the drop down arrow next to 'Settings' menu and choose 'Notifications '.

    3. If please check or clear the parameters of notifications that you prefer and then click on "save changes".

    Please let me know how it turns out.

  • Color Laserjet PRO MFPF 377dw: problem with Color Laserjet PRO MFPF 377dw and HP network scanner

    After removing the package of printer drivers HP, all attempts of resettlement via WLAN regularly fail before the end, which indicates that the device is not found. I physically connect the printer to the computer by USB cable to install the software successfully. When I go to WLAN Wireless thereafter, the printer works perfectly within the network. If I remove the USB cable, the following error message appears when I try to start scanning HP: HP CLJM377 Scan found . In other words, HP Scan cannot be used with a PC not connected by USB cable. All other remote features function normally printer in wireless, including HP Scan & Capture. Is there a possibility to correct this, via the Windows registry from my PC?

    MrRobot wrote:

    Hello! @Chirsistei, your description of the HP product is classified as a commercial product (business). Our sales support team provides support via the channel of entry here. If you need immediate assistance, you will need to open a session one business with our sales support team. Click on this link http://ow.ly/I3gw30140F8 for more details.
    Let me know if you want more information and/or assistance.

    Have a great day!

    See you soon!

    Hello Chetan,

    I think I'm in the wrong forum here because I live in Switzerland and here the Laserjet Pro M377dw color is sold to private users. I have no access to a support plan and use the printer in my home office network. Your proposed solution therefore does not help me, during this time, I have posted this problem in the forum on language German you need not to pursue this new. Thanks anyway

  • HP LaserJet Pro M277dw Color printer

    I can't install my hp color laserjet pro m277dw printer on my computer windows 10. Any suggestions?

    Hello @Scottro, greetings!

    Welcome to the HP Forum! It is a wonderful location to converse with the community, get help and advice.

    I understand that you are having problems installing your printer LaserJet computer Win 10. I will definitely do my best to help you.

    What is the error you get when installing the printer? Where you can connect the printer to the network?

    Otherwise, please see http://hp.care/2dQkgAr for installation instructions. If the printer is not found while installing, perform the steps mentioned here: http://hp.care/2dQk7Nl

    Please let me know if it works for you. Thank you!

    See you soon

    Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

Maybe you are looking for

  • How to use the "back" button to return to the new page tab in FF15

    In FF14 I could(1) open the new tab and see the new tabs with thumbnails of page 9 page.2) click on a thumbnail and go to this page.(3) click on the back of FF button, who took me to the new tab page so I could click on some other thumbnail. In FF15

  • A few quick questions about the Satellite P300 - 18 M

    Hello I am about to order a Satellite P300 - 18 M and have just a few questions about this: (Although these may apply for other similar Satellite/Equium P300.) Is the touchpad made by / to use the Alps or Synaptics driver? It has the Wireless N netwo

  • Problems with wifi, bluetooth and gps in my iphone after updating iOS 6

    After that the last iOS 9.3 update my iphone 6 has problems with wifi, bluetooth and gps. Now, my wifi connection is slower and falls easily on a short distance. My bluetooth does the same. But the biggest problem is the GPS on my phone. I tried Isla

  • ADF duplex for LaserJet models?

    HelloI'm looking for a laserjet model features automatic duplex ADF. So that the device can perform a copy double-sided on a stack of documents face / back loaded in the ADF. Thus, 2 faces-> option 2 sides for the copy and scan. I am grateful if anyo

  • Email from Hotmail or Windows Live account has problems

    I get emails that say they are from the Hotmail support team (* address email is removed from the privacy *) and the body of the email: Windows MSN Hotmail is fast, more secure than ever before and filled with new ways to stay in touch. Storage that