HP Officejet 7410 error

I have a 7410, that does not illuminate.

When I plug it in, the screen lights up with the HP logo, BUT at the bottom of the logo "HP invent", he has a "loading" as if it loads software graphic type. It never stops, I can leave it for 2 hours and return, and it always does. Also during this question any of the book of buttons... and even not "WE" or "Setup" "

If I press the button 'ON', the screen goes black, then the HP Logo and loading graphic software starts again.

Any ideas what the problem is?

Is there a reset of the system?

This is usually caused by a failure of the wireless LAN card.  You can solve this problem, as shown on this page. Unplug the connector on the wireless card will disable wireless and correct the problem.

If you are using a LAN or USB connection, this should solve the problem.  If you use a wireless connection, you may need to set up a wired LAN if possible.

Tags: HP Printers

Similar Questions

  • Fax/scan without a phone with officejet 7410 all-in-one line

    I have an officejet 7410 all-in-one and UNPLUGGED my phone line at home. How to download software in order to fax/scan items? I get the message error is "you must install or run HP software for this feature.

    Here is a link that will help you with that.

    http://WWW8.HP.com/us/en/support-drivers.html

    1. Enter the name of your printer DRIVERS AND SOFTWARE

    2. choose your operating system

    3. then, when he asked to SELECT A DOWNLOAD, choose the software FULL of FEATURES.

    Let me know if this can help, thank you.

  • HP OfficeJet 7410 fails to install

    I tried to install my HP OfficeJet 7410 on two different machines to Vista, but I'm getting Fatal Error 2203 on both machines with every attempt to set up the PRINTER. I downloaded the last set of drivers for systems respective 32/64-bit, and if it is 32/64-bit system, HP.com points you to the same file named: AIO_CDB_Full_Network_enu_NB.exe.

    Both machines have Windows Vista Home Premium Service Pack 2. A machine, a s3307c of HP, installed Vista 32 bit and the other a Dell Studio 1537, Vista 64-bit installed. In addition to Service Pack 2, every machine had any other possible update installed via Windows Update, and each machine also has Internet Explorer 8 is installed, if that makes a difference.

    About midway through each attempt to install the software, I get the same 'fatal error' error code 2203 but the message will read a little differently each time. There is usually a different end with the "MSI.xxxxxx" message, causing an unknown problem. The last of them was "MSI. Bufferchm ".

    The HP OJ 7410 is on Vista hardware compatibility list and I had already installed the OJ 7410 on each of these machines with no problems, and I even used the 7410 on both machines without any problem. HP desktop computer has been connected via USB and the Dell laptop was connected wireless. However, my HP s3307c desktop computer hard drive died recently and I had to replace it. Currently all reinstall, I ran into this dam with the 7410. I didn't have to reload Vista on Dell Studio 1537, but about 3-4 months before the death of the desktop computer HP laptop Dell stopped communicating wirelessly with the OJ 7410, so I took the opportunity to recharge both machines.

    I even followed the solutions on the next web page, but I had no luck with a successful installation:

    http://support.HP.com/us-en/document/c00459898

    I could really use some help here. I never had so many bad install a piece of HP hardware, especially something like a printer/scanner (in this case an AIO). It makes no sense to me that I could install this before AIO and work all of a sudden not complete installation on the same machine with the same operating systems. Also, is there any sense to me that HP just posted the updated files this month here, and none of them work.

    Help!

    Try the steps below and let us know if it is your problem. I got from a document of error 2203 on microsoft.com (http://support.microsoft.com/kb/2000547)

    * Add the group with full control permissions everyone to the list of permissions of the default temporary files folder:

    1. Click the Windows menu button (formerly start) or press the Windows keyboard.
    2. In the start search box type % temp %, and then click the Temp folder item that appears at the top.
    3. At the top of the window of the Explorer, in the address bar, click the folder to the left of Temp in the path of the folder (default Local).
    4. In the folder list, right-click the Temp folder and then click Properties and then click the Security tab.
    5. Click the button change... and on the next screen, click Add.
    6. On the screen in the window large text type everyone and then click on check names - everyone should then be highlighted.
    7. Check the Full control under the column allow and then click OK, then OK again and OK again to close all windows.
  • Install OfficeJet 8600 with OfficeJet 7410

    I use a current version of Windows 7, SP1.  Can I install an OfficeJet 8600 on the same computer that also uses an OfficeJet 7410? It seems that when I install the software 8600, it trashes the 7410 installation.

    Both printers have coexisted on my laptop Dell for ten days it seems that the problem has been resolved by uninstalling them both, and then reinstall the 7410 has my work, followed by a relocation of the 8600 at my house using the software downloaded from HP instead of the software from the installation of 8600 disc.  The 8600 without the 7410 was also stable on installing MacBook Pro Bootcamp to my wife for the same period.  Thanks for your help.

  • Is it possible to use the wizard to analysis of Microsoft with all-in-one HP Officejet 7410?

    I have a HP Officejet 7410 connected to my system and it works well had to analyze the documents, that I prefer software that comes in the accessories of Windows XP. Naturally, the HP software overrides this facility and the scanner is not seen. Is it possible to make visible in the Microsoft program?

    Thanks for your suggestions.

    If the printer is connected by USB cable, you should find the scanner icon in the control panel > Scanners and cameras. If you double-click on the icon of the scanner, it should start the wizard for scanning.

  • OfficeJet 7410: officejet 7410

    I bought two ink cartridges at the Denmark (HP 344 and HP339) for my HP Officejet 7410, on cards, it is mentioned that they are suitable for my printer. However, during installation, I received a message that they are not "compatible" with my printer.

    I understand that there could be a problem from one area to another?, in this regard, please note that I am currently resident in the Venezuela, which is also where the printer was initially purchased.

    I checked the warranty with HP, but it expired

    How to solve this problem?

    Welcome to the HP community @Hawkeye1,

    I came across your post about the use of cartridges for your Officejet 7410 in a different region that the printer was bought in. In your particular situation, a discount to zero 'regionalisation' will be made on your HP printer directly, so that the printer accepts the cartridges you are trying to use.

    Contact HP by following these steps. If you have problems with to join to do the reset, please let me know!

    Testify of my answer by pressing the thumb in the air below and hit the "accept as Solution" button, if I have you helped a resolution!

    Contact HP:

    Step 1. Open the link: www.hp.com/contacthp/
    Step 2. Enter the product number or select Auto detection
    Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
    Step 4. Scroll down and click on: contact HP options - click Get phone number
    File number and phone number appear

     

  • Unable to install the solution on Officejet 7410 Center.

    Windows 8 with all-in-one Officejet 7410.  Print wireless, but cannot scan.  I downloaded the latest version of the software.  What Solution Center to open I get "cannot run because the device is not over.

    I tried loading CD but windows 8 can not "run as.."

    Thanks for any help.

    Hi Raindrop211 and welcome to the forums of HP!

    I'm sorry to hear you had problems with the solution Center HP regarding your Officejet 7410, but I will certainly do my best to help out

    It really looks like that something is not to proceed with the installation correctly, so to start I would like that you start by removing the software HP using HP Officejet software and driver removal utility and then once it is removed, I would like to you clear your Temp folder as well.

    Once this is done, I would recommend that you reboot your PC and then go to download and run the HP printer installation wizard as it should be able to download and install the most recent drivers for you.

    I would like to know how it goes for you!

  • All-in-one HP Officejet 7410: your printer cannot be found on your wireless network

    I have a home network and two printers connected wirelessly. One is HP Laserjet P1102w and works very well. The other is all-in-one HP Officejet 7410 and I am not able to connect to it. I installed the HP software, but it fails to detect the printer. It was working fine before the update from Windows 8.1 for Windows 10.

    I am able to ping the printer IP. If I enter the IP address on my browser I see the printer (see photo below) and it let me scan (see photo display preview).  But I could not find where to go the scan! It is not in my scans.

    I ran HP print and Scan doctor and it shows the HP Officejet 7400 series. When I select and press Next, it says: failed to communicate with your selected product. I noticed that the IP address is slightly different from the actual IP address that has the format: xx.x.x.xx. Than that shown is xx.x.xxx. Which ' don't know if it's part of the problem.

    Any help would be appreciated. Thank you.

    Hello

    If you still experience this issue, download and install the following software and check to see if that can help you:

    http://ftp.HP.com/pub/softlib/software13/COL30951/MP-110165-3/AIO_CDB_Net_Full_Win_WW_140_408-5.exe

    Shlomi

  • OfficeJet 7410 wireless configuration

    I have an OfficeJet 7410 all in one on a Windows 7 system.  I want to print wireless from my laptop to the printer.  I installed drivers and can print when connected but don't know how to print wireless.  Specific help would be greatly appreciated

    The printer should accept WPA but not WPA2 and it may not even accept WPA/WPA2 mixed mode.

  • OfficeJet 7410 Driver Install on Windows Mobile 8.1

    I'm trying to install the HP OfficeJet 7410 all-in-one printer driver.   I downloaded the HP Printer Wizard, the printer has detected and started the installation.    I also ran printing HP and doctor scan which has also detected the printer (in a network) and started the installation.   These two tools, download and run the installation package AIO_CDA_FSW_Full_Win_WW_140_408-5.   This is the process fails.   The software is installed, and then seeks to determine the printer - my printer is connected to the network via ethernet.   When the software does not find the printer, I restart the scan, it fails.  Finally, I wonder if I want to enter the IP (192.168.0.102), and I re - search for the printer.  Saying the direct IP address software does not work, he doesn't know how to find the printer.   I can ping, I can access the printer web page, the PC can connect to the printer and find, the installation of driver software does not work.   To reconfigure the printer and the laptop to use it wireless to repeat the search - always the software can't find the printer, so do not install the print driver or the installation of the software.   If I run the HP Solution Center, it will fail, telling me to set up the printer.   I went through this process as well - he too fails to find the printer.

    How can I get the software to recognize the printer so that the installation may complete and I can use the scanner/printer/etc. ?

    Hello

    Download and install the following software:

    http://ftp.HP.com/pub/softlib/software13/COL30951/MP-110165-3/AIO_CDB_Net_Full_Win_WW_140_408-5.exe

    Please let me know how it goes,

    Shlomi

  • HP Officejet 7612: Replacement HP Officejet 7410 all in one HP Officejet 7612 e-all-in-one

    I have currently a HP Officejet 7410 all-in-one which includes the program Solution Center, I bought a HP 7612 Officejet 7612 e-all-in-one. Do I need to uninstall first the 7410 HP? The HP 7612 aura the program Solution on the installion also CD? I need a program that tells my computer when I'm scanning to save JPEG files in my computert.

    I also have a HP Photosmart 8050 installed which is my primary printer.

    Which of the following programs do I need to uninstall related to the HP 7410?

    HP Photosmart, Officejet and Deskjet All - In - One Driver Software 13.0 rel. B

    13.0 HP solutions Center

    HP Smartweb printing 4.51

    HP Photosmart Essential 3.5

    Program HP Customer Participation 13.0

    Imaging of the functions of the unit 13.0 HP

    HP update

    I don't want to uninstall whatever it is that might interfere with my active 8050 printer and driver

    The Hp uninstaller States "if I have multiple HD devices choose to uninstall all HP products associated with this device" will affect some of the other printing imaging devices or it asks to choose programs to uninstall.

  • Need advice on the installation of the driver (Generac monitor pnp) officejet 7410

    Hello I have an Officejet 7410 MFP, Win7 Home Premium 32-bit and a 32 bit IE9. I have a third-party driver updater (Driver Boost) I did a scan for new drivers and installed all the drivers except the drivers OJ7400. . These 2 drivers are generic pnp monitor that have a different icon for my HP officejet 7400 series. Boost driver support said I should install all updates. However, I request support here because I am wary of a pilot who is not associated with my officejet 7410 icom. Please provide recommendations related to this issue. Thank you.

    Hello

    You can download the drivers for your printer below:

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-76971-1&cc=us&DLC=en&LC=en&OS=4062&product=391194&sw_lang=

    Proior start the installation, be sure to unplug the USB and restart the PC, and then start the installation. You will be guided to connect the USB cable during the installation process.

    Kind regards

    Shlomi

  • HP OfficeJet 7410 connect wirelessly to a wireless computer

    I have a HP OfficeJet 7410, which seems to work if the computer or printer is conncected to the network by an ethernet cable.  If both are wireless, the printer cannot be seen from the computer.  Any help will be greatly appreciated.

    Thanks in advance,

    John Novak

    What router?  You can get in its settings? If so, search for "Isolation wireless" or just "insulation" and disable it.  This setting blocks communication between customers Wi-wired and on the router.

  • HP Officejet j5750 error print saying "on paper" but it is not

    HP Officejet j5750 error print saying "on paper" but it is not, there 20 sheets. I remove and replace the paper and press OK and the same error.

    Typically when you get an error "on paper", the rollers slide and need to be cleaned.  The document below should help you work through the problem.  If this does not work, you will need to replace the printer.

    "Out of paper" Error Message is displayed and the product is not look upward or feeding of the paper:

    http://support.HP.com/us-en/document/c00786157

  • OfficeJet 7410 & WPA2

    I have a MAC wireless network and I can not connect my Officejet 7410.  The only options on the 7410 wireless are wep and wpa (not wpa2).  Y at - it a firmware update that will allow WPA2?  I am also unable to reach my printer when it is connected directly to the MAC Time capsule.  Any help would be appreciated.

    Thank you

    It should take WPA - TKIP, but the display say WEP.  Try it.

    In addition, and I know this sounds strange, but change the Router 2.4 GHz channel to 11.

Maybe you are looking for

  • How to open Satellite 1130?

    Hellomilk has fallen in the back of the unit to my computer laptop satellite 1130.so far, the laptop does not start. After pressing the button, green light in the front of the computer flashes for a moment and nothing happens.now I need a manual to o

  • Not able to use WPA on a Satellite Pro 4600

    Hi guys,.I am not able to set up authentication WPA on my Satellite Pro 4600. This possibility is not in the network authentication drop-down list in the Properties dialog box (only open and shared).Is there a support for WPA in the bed of the laptop

  • Error: Failed to initialize the window when trying to play the game

    Original title: failed to initialize the window Due to a virus I had to restart and make my computer cleaned.  I was able to play Iwin games before the clean and since I put everything back in but when I went to go play the game, it is said that the

  • Two MacBook with a mg6320 - can scan the other cannot

    Hi all I have two Macbook Pro, the Mavericks running.  I installed any software of Canon printer on either.  On one of the macbook pro, I can scan my wifi connected MG6320 in construction in Preview app.  On the other hand, I can't.  It is said that

  • HP chromebook: removing battery

    I can't open the back to check the product # or change the battery