HP Officejet Pro 8600: Document feeder causing vertical lines in copying and scanning

Similar Questions

• HP Officejet Pro 8600 Premium: Printer leaves black lines during copy and scan from ADF

  I know this question has been asked several times, but whenever I try to copy or scan from the automatic document feeder, it leaves black lines on the copy (with the document on the works of glass like a charm).  I've read through the forums and have tried the advice to unplug the machine and so on, but none of these suggestions work.  Any help would be appreciated.

  Hey @Huskers1,

  Welcome to the HP's Support Forum!

  I see that you have some problems with a line when copying from the document on your Officejet 8600 Premium feeder e-all-in-one printer. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  1. Get a little water and a lint cloth.
  2. Open the left upper part of the printer, where the document since the charger goes into the printer. It should open up as you opened a book.
  3. With your damp cloth wipe the rubber stamp, the rollers in the cover and the casters on the bottom of this section.
  4. Again open the left side of the printer, as you opened a book.
  5. With your damp cloth, wipe the rollers, you will find inside this section.
  6. Close the upper sections of the printer and open the flat section.
  7. With your damp cloth wipe the rollers and the white bar you see on top of the printer
  8. Clean the glass on the left side of the printer.

  Once all the pieces you cleaned dry, please let me know the results. If you remove the line, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• OfficeJet pro 8600 more: 2 black vertical line when scanning only

  I get 2 vertical black lines while scanning using the ADF. This does NOT happen when you use flat bed scanning. Also, this does not happen with copies in the ADF or flat bed - scan only using the car power.

  Not an expert on your device, but if you look on the side of the adf, where the paper feeds, you open the lid to the scanner glass is displayed.  Now on the left side is where the adf feed above to scan paper is on the side left where there will be some dirt or material causing lines.  Usually, you can take the copy that came out and line up so you can see the dots making line.  Sometimes, you need to use your nails to kind of scratch material out of the glass.  I usually rub really hard with some windex first, and if that does not work, I line up the and scrape the residue out of the glass.  Again, it will be on the left side of the window in an inch on the left side.

• HP Officejet Pro more than 8600: HP Officejet Pro 8600 more black vertical line when copy or scan with automatic feeding

  HP Officejet Pro 8600 more black vertical line when copying or scanning using auto flow only.  It works very well on the flat.

  It is now resolved.  It seems that there is a strip of glass that is used for the automatic copy of power and research.  The glass has a note on it that I cleaned which solved my problem of vertical line.

• HP Officejet Pro 8600 more black vertical line when copy or scan

  HP Officejet Pro 8600 more black vertical line when copy or scan everything in the middle of the page

  Hi Clementstl,

  I understand that you have a 8600 Pro Officejet which puts a black vertical line in the center of your copies/scans. I'm sorry to hear you had to deal with this, but I will certainly do my best to help you solve this problem.

  I recommend the rest of this document of vertical stripes, lines or streaks in the Copies, faxes or Scans as it should be in a position to help to cross that line. The most common cause is a small spot of something on the glass of the scanner, so just make sure that when you're cleaning use you as much elbow grease you can collect

  Just to clarify a little further, if the problem only seems to occur when you use the automatic document feeder, you'll want to focus your attention on the small strip of glass that he uses on the left side. If it only occurs when you use the flat glass, you want to concentrate on the large piece of glass he uses.

  Hope this helps, have a nice day!

• OfficeJet pro 8600 print a single vertical black line when using the charger

  OfficeJet pro 8600 print a single vertical black line when using the charger

  Hi @realestatejeann,

  I see that you have found one black vertical line when using the ADF. With a few steps, we should be able to solve this problem.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Here is a document for the cleaning of the glass Strip and the underside of the scanner cover.

  Vertical stripes, lines or streaks on Copies, faxes or scans.

  If you need help, let me know.

  Good day!
  Thank you.

• HP Officejet Pro 8600: No Wifi connection between the computer laptop and HP printer

  Hi, I just added W10 os for my laptop, I was on os W7, work system very well, my printer is Office Jet Pro 8600, both laptop and printer are connected to my wireless router, but my laptop cannot find my printer, I misplaced my original disc, can anyone advise me on what it takes to please. TIA

  Hi @Rockabilly,

  I was able to locate the software you're looking for, but from your description, not having is not the software may not be the question. I will first provide you with the software, then if you continue to have problems, let me know and we can go from there.

  Printers HP Officejet Pro 8600 Plus and Premium e-All-in-One

  E-all-in-one printer, HP Officejet Pro 8600 - N911a

  Alternatively, you can also download and run the HP printer install wizard for Windows

  The HP printer for window installation wizard was created to help users download and install the latest and most appropriate HP software solution for their HP printer.

• HP OfficeJet Pro 8600: Accidentally hit disable all in settings admin and can't go in the settings.

  I'm went to the site with the ip address andwhile I was in admin settings I touched off all and accidentally disabled the built-in networking features. How can I go back.

  Hi, if this solution worked for you please go to options and click on accept as solution and click on Bravo to give a shout out. Thanks, Baumtech1

  Hello @baumtech1,

  Welcome to the Forums of HP's Support. I understand that you have accidentally disabled your Officejet Pro 8600 network capabilities. I would like to help.

  I you sent a private message with instructions to access the menu of the toggle from the Panel of 8600.

  Please note: when you turn on either from EWS (embedded Web server) printer or front panel NEVER activate control lock. It can cause a very undesirable situation. Also please don't be one of those rare people who adds a password to access EWS of the printer. These passwords also cause a lot of grief. Especially because they are really hard reset and easily forgotten. Add to that the fact that he has not forgotten the password option and you have a recipe for disaster... Well... It has been my experience anyway.

  If you access the menu toggle and you get things working again, tell by the accepted solution.

• HP Officejet Pro 8600 Plus: software the Printer Wizard does nothing and eats CPU

  Hello

  I currently have a problem with the HP printer Assistant software. I use a HP Officejet Pro 8600. Well I uninstalled and reinstalled several times, redownloaded the latest version of the software from the HP site, tried with a wireless connection and a USB connection, but still have this same problem.

  The problem is when I open the printer to the printer Assistant software (scan, definition of printing preferences, etc.) nothing loads and what I noticed is that in the Task Manager, the program is constantly, nonstop to duplicate in the Task Manager and eventually slow down the computer because of the high use of the processor of these duplicates. I can't stop these processes in time compared to the amount of tasks in doubles at this very moment, and the only way to stop it is to restart the computer. I had this problem with Windows 8.1 and so I've upgraded to Windows 10 but exactly the same problem occurs. If I wait long if I get an error (0xc0000142) telling me that I can not load the Printer Wizard, but the process will still duplicate.

  I tried using the printer with other computers, but they do not have a problem by launching the wizard from the printer. I wonder what is happening and why is the Printer Wizard launch multiple neverending himself as tasks on the Task Manager?

  Add to that, printing works fine, it is train to launch the Printing Assistant software that is causing the problem.

  Hello @jellyjr,

• OfficeJet pro 8600 printer-how to make this program work and installation?

  I have problems printing. I wonder how to ste it to the top and do work.

  Moved from feedback

  Original title; printer Officejet pro 8600

  Hi David,

  1. what operating system is installed?

  2. what security software is installed?

  You can go through the printer manual to know how to set up the printer and make it work.

  You can also refer to these items and check if that helps.

  http://h30434.www3.HP.com/T5/printer-all-in-one-install-setup-e-g-Windows-8/How-do-I-install-printer-software-on-HP-OfficeJet-Pro-8600/TD-p/1123283

  http://h30434.www3.HP.com/T5/forums/SearchPage/tab/message?filter=labels%2Clocation&location=Forum-Board%3AInstall&q=OfficeJet+Pro+8600+printer

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• HP Officejet Pro 8600 + not to recognize the new real black and yellow ink cartridge

  HP Officejet Pro 8600 +, this machine is 1 year old, just out of warranty and is not recognizing the new yellow and black cartridges HP ink. Tried the hard reset and cleaning the parts set out in other posts in this forum without success.

  Disappointing that the colored inks run low if fast even when you do BLACK only printing and now that the mahine a work stoppage at its destination.

  Any help/ideas?

  Hello

  As you have tried with the new cartridges, I think it might be a problem with the printer or the print head.

  Please call the HP Technical Support for assistance.

  If you are in US , toll free # is 1-800-474-6836.

  If you are not in US , then log on to www.hp.com , bottom left it is an icon of the world map, click it, then select the region that you belong to, which would then provide the support options for you for this region.

  Kind regards
  Jabzi

  Give Kudos to say 'Thank you' by clicking on the White Star under my name.

  Click on "'Accept as Solution" if it has solved your problem, if others can find. "
  I work for HP

• HP Officejet Pro L7780 - document feeder does not attract pages. The charger did not result in pages using

  I have an Officejet L7780 which is not driven by the document feeder. He finds himself with the first page and try to in the page but it gets stuck with it.  I wasn't able to get through, but I can enter a part of the page that is stuck and shoot OK.  It seems that the rollers do not work much more.  Is this something that can be corrected/fixed/replaced?

  Hello

  Make sure you use media supported (weight/type).  If you frequently use your ADF, you can have an accumulation on the pick up rollers.  I have included a link below that describes how to clean them and how do I check to make sure that there is no piece of paper stuck under the hood of the ADF that would prevent to draw correctly.  Good luck!

  http://support.HP.com/us-en/document/c02019585

• OfficeJet Pro L7780: Officejet Pro L7780 missing of the vertical lines on text & photos

  Everything that I try to print has lack of vertical lines, text or photos. Happens if I print from my computer or if I try to copy a page directly to the printer. I went through the troubleshooting page full... the ink is all well heads, all good impression. Whenever I try to run a printer align it does not end the page. Whenever I have nothing he's trying to align printer print when its done & still cannot print the entire page. Gives me an error and says to check my documataion. I checked the book with my printer & there is nothing in this whole problem.

  Help, please!

  Hi @LockGal,

  Welcome to the Forums of HP Support!

  I see that you are having problems with your HP Officejet Pro L7780 printer aligning and printing vertical lines. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand the frustration that this must be for you. Looks like there are two separate issues. When the printer clean print heads and not properly align itself, this indicates that there is a problem with the cartridge, the print head or the line break. For vertical lines, it is usually independent for cartridges and print heads (not being is not a print quality problem). The paper type and print settings might be the problem.

  To help determine the cause have you used this document: troubleshoot print quality HP Officejet Pro L7500, L7600, and L7700 all-in-One Printer Series?

  Use the document in the order will help you determine if the print heads need to be replaced. If so, please contact HP.

  Please confirm that the vertical or horizontal lines?

  NOTE: are not replace the cartridges and printheads for vertical streaks in a print. Instead, check the paper as directed earlier in this document, or search for a document that addresses this issue. Vertical streaks on copies can often be fixed by cleaning the scanner glass.

  • L7300 of HP Officejet Pro L7500, L7600 and series L7700 each - vertical stripes, lines or streaks on Copies, faxes or scan

  If you have completed all the above steps and your product still has a problem, service the product.

  Contact HP for service in all countries except Asia-Pacific.
  First, check your product warranty to check your warranty printer status and then go to contact HP support to find an authorized dealer or to schedule a repair.
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• HP OfficeJet Pro 8620 color wireless Photo printer with Scanner, copier and fax machine (A7F65A #B1H)

  I want to buy HP printer OfficeJet Pro 8620 wireless color Photo with Scanner, copier and fax machine (A7F65A #B1H), but I want to know if the product can use photo cards to print photos. The product also allows to print normal word documents? Thanks to an expected answer.

  Chima.

  Hello

  First of all, it's a printer and Yes it can print Word documents, it can print photos on photo paper.

  Kind regards.

• vertical lines when copying or scanning with my c6180 printer

  6180 all in a print is fine, just copy & fax causes the vertical black line on the side only. site filled with HP troubleshoot process - no change. Can anyone help. printer is about 2 years

  I don't know if this will help anyone, but I had a problem with a black line when fax is received or when copying through my document feeder.  The quality was very good for printing and copying via the flat glass.

  Here's what I did for a solution... copy of the elevator panel to expose the big glass, then carefully lift on the small gray bonbout charger doc Center, this will take a little effort but don't break anything.

  Once up on hinge, put your fingers on the two gray side tabs to lift the next part with the rollers.  This will now expose a small ~ 2 x 9 "piece of glass that has probably debris like mine did.  Clean with windex and closing...

  I hope this helps.  Don't throw it!

  David