HP Pavilion 17 j7b57av: need of repair to install the memory and hard drive

Similar Questions

• Equium A200 PSAE8E: Need info on memory and HARD drive upgrade

  In the manual of my Equium A200 PSAE8E described the possibility for the user to add a second internal hard drive and upgrade the memory from 2 GB to 4 GB. This can be done by the end user without taking the laptop to the local service for repair.

  I would like to order a 200 GB internal second hard drive, as well as to replace the 2 chips of 2 GB of Ram with 2 4 GB chips, but I find not the product ID for these modules, because it seems that this model of Toshiba psae8e is not registered for compatibility.

  Someone has technical details about the product ID and the cost to be sure to order the right parts without compatibility issues?
  Thank you
  Paolo

  Hello

  I would like to add some info on the second HARD drive on laptop Equium A200 upgrade.
  As far as I know all the A200 are delivered with the second HARD drive location. This location is available, but not all phones of A200 could be improved with the second HARD disk, since it lacks the second HARD disk controller interface.

  Therefore, you should be 100% sure if your laptop can handle the second HDD.
  You can simply check this remove the cover of the location of the HDD on the second and check if the connection of the HARD disk is available.
  If this isn't the case, then you cannot move the laptop with the second HARD drive.

  Now something about the memory.
  I studied in the internet for some compatible modules and surprise, surprise ;)
  Found this wonderful site:
  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=30715&ft=m&St=3

  According to the news the portable supports the DDR2 667 MHz (PC2-5300) 200-PIN SODIMM memory modules.

  All parts such as memory or HARD drive can be ordered also with the service provider authorized in your country!

  Good bye

• Pavilion dv6t-6100: DST tests, running-in, System Tune Up and hard drive failed - which means ID failure?

  The above tests failed, and passed the SMART tests, memory and battery.  I had problems with a program so I rean these diagnoses.  Failure ID is 9LGDWX-5M984B-MFH15G-60SN03.  What is the code of failure?  If I need a new hard drive, how can I find out what you get it?

  Hello

  The error code 24 characters is a disk failure short self-test and would indicate that hard is defective and must be replaced.

  The player at the link below is an example of one that would be perfect for your laptop.

  750 GB hard drive for laptop.

  The procedure to replace the hard drive begins on Page 70 of your & Maintenance Guide.

  Once this is done, simply use your recovery media to reinstall the operating system on the new drive - this is described in the document of HP here.

  Kind regards

  DP - K

• Desktop HP Pavilion p6130y PC, installation of Windows 7 on the new SATA hard drive problem

  First of all, I can't find the model p6130y number on the HP Support.  The original hard drive came out and it was replaced with a Seagate SATA 850 GB drive, buy Windows 7 on DVD and I tried to install. Obtained through formatting the drive. Their only option now is to "Load a driver."  He says that I need to locate the HD driver on the media and press OK.  I can't find such an on installation disk so will try the find the right HD drivers for this model computer download on a USB key. Any ideas?

  Hello:

  Here is the link for the driver sata for your model:

  Just download it and do not run it.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=PV-77141-1&cc=us&DLC=en&LC=en&OS=4063&product=3980095&sw_lang=

  The motherboard in your model has major problems with the drives out and that the results in the hard drive and DVD drive from the BIOS endangered.

  It could happen to your model, it's why W7 cannot find the hard drive.

  You will need to download and install this free program.

  http://7-zip.org/

  After installing 7 - Zip, right-click on the Sata driver you downloaded and select 7 - zip option in the list.

  Select extract to: I leave extract the name of the file and extract the exe file in a folder of driver.

  Once you have the file, open it and copy the contents of the folder on a drive portable usb flash without the src folder.

  With the flash player and the installation of W7 media connected to the computer, boot from the installation of W7 media.

  After selecting the install now option, select the training - Advanced menu, Options and select the option load a driver.

  You should now see the storage driver files listed.

  If you check the box, it only includes the compatible driver.

  Follow the prompts and hopefully, W7 should install correctly.

• HP Pavilion g6-1322se Notebook: [SOLVED] cannot find/install the appropriate network controller driver

  Hello

  I installed Windows 7 64 bit as a SECOND OS on my laptop, everything goes very well with Windows 10 a.

  On Windows 7, the Netowrk controller driver is missing and I can not connect to Internet via Wifi.

  I manage to find a suitable driver for my network controller (don't know if it's Broadcom and Realtek).

  I tried to install a large number of them, and finally, it fails with the error:

  ["0" error and the installation program cannot contiune]

  Product name:

  Laptop HP Pavilion G6-1322se

  Hardware ID:

  PCI\VEN_14E4 & DEV_4727 & SUBSYS_1795103C & REV_01
  PCI\VEN_14E4 & DEV_4727 & SUBSYS_1795103C
  PCI\VEN_14E4 & DEV_4727 & CC_028000
  PCI\VEN_14E4 & DEV_4727 & CC_0280

  Any suggestions?

  Concerning

  Hello world

  I found a solution for this. I downloaded the driver appropriate from this link:

  http://support.HP.com/my-en/drivers/selfservice/swdetails/HP-Pavilion-G6-1300-notebook-PC-series/5186808/model/5218300/swItemId/ob-95652-2

  After extraction, it will start the installation, and the error appears again. Nevertheless, follow these steps after the error:

  1. Locate the file extraction. [You can see address during extraction after clicking on the downloaded file.]

  2. go to the Device Manager, right-click on the network controller and click Update driver software.

  3. choose to do it manually. Find the folder of extraction [I mentioned earlier].

  4. made!

  * Do not forget that, in order to get the best driver, you should IDENTIFY YOUR PRODUCTS AUTOMATICALLY by the HP Web site and then go to its pilots!

  Concerning

• G6 2312ax Pavilion: Pavilion g6 2312ax keyboard does not respond after the death of hard drive

  My laptop received disc hard failure two months and he died since then. I intend to change the hard drive of the laptop as soon as the order arrives in a few days. But now the problem is that as if now the keyboard of my laptop does not respond. So I would like to know if this problem will be resolved after the replacement of hard disk or is related to the software / operating system of your laptop?

  Help, please...

  Sorry I couldn't answer yesterday.

  The update, is that when I tried to turn on the laptop as well by pressing the ESC. The laptop did not respond initially but then responded in the end, but after that, there is no answer.

  Now Mr. President, I would like to know your end on this issue?

  Thank you

• Pavilion DV6 freezes but passes the Tests of memory and HARD drive

  I have a dv6-3025dx that the POST is fine. It does not start after the screen 7 start, the recovery Partition loading bar or a Windows 7 recovery disk loading bar. The HP Vision diagnostic and a drive OEM 7 freeze as well. Start with a Ubuntu DVD displays icon on the keyboard at the bottom then nothing else than a cursor flashing at the top left of the screen. The HARD drive and memory in the BIOS Tests pass but the start-up Test, the Burn-in Test and the Test of memory in the partition the disk diagnostic all freeze immediately.

  I reset BIOS, change the RAM with known working sticks and clone the HDD on a well known player and still get the same result. I had to clone the drive from a different machine, because Acronis True Image 2011 boot disk crashes after the splash screen. A 3rd party BACK base RAM and HDD tests pass with flying colors; including Windows, MemTest86 Memory Diagnostic + and video memory Stress test. Basically, I can't start any GUI environment. only of DOS or Linux command line. I'm guessing that maybe the video chip? Ideas or confirm my diagnosis?

  Thank you!

  You make text based OSes seem to work well. This could mean that the video card is at fault with loads greater than the bare.

  However, it could also be a SATA controller flaw that does not correctly handle the load. There is really no way to test this reliable I found.

  No matter whether the video controller or the controller SATA, the result is the same and that is replace the motherboard. If it was office, a SATA PCI-based controller can be purchased cheap enough to exclude it. However, this is not an option here.

  It really isn't too much other material in a notebook that is involved in the boot process and most of the material is soldered to the motherboard.

  I'm sorry.

• My original XP Pro disc is SP2. I've updated to SP3 and now I have corrupted files and need to repair windows with the disc.

  My original XP Pro disc is SP2. I've updated to SP3 and now I have corrupted files and need to repair windows with the disc. When I put disc SP2 in it tells me that it is a work old version and custom. How to make a disc with SP3 top to repair my OS?

  Hi DFPI.

  I suggest you to uninstall Service Pack 3 temporarily on your computer.

  How to remove Windows XP Service Pack 3 from your computer

  Later, try to repair the computer with the Windows XP disc and check if it works.

  Later, reinstall the Service Pack 3 after the computer repair.

  Reference: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  Hope the helps of information.

  Please post back and we do know.

• HP Pavilion 550-055na: new disk will not install the new operating system

  Hello

  I bought a new HP Pavilion 550 - 055na with Windows 8 a month or two ago but want to use Windows 7. However, I decided that I will keep the hard, the PC came with, and have the option of Windows 8 in future if I want. So, I'm installing Windows 7 on a new hard drive.

  My problem is that the new copy of Windows 7 will not install on my new hard drive.  I get:

  Violation of secure boot

  Invalid signature detected. See the policy in the configuration of secure boot

  Then me to a black screen after I pressed Enter/Ok, who said the following.

  Check the presence of the media...

  Media present...

  On IPv4 PXE boot.

  If I press F12 on power on, I get a blue box asking me to select a boot device. The only options are:

  Realtek PCIe GBE Family Controller IPv4
  

  Realtek PCIe GBE Family Controller IPv6

  and the output by using the arrow keys

  How to change the secure boot strategy?  If I do, it means that I can install my 7 can I on my new hard drive? Also, providing that I do, I always will be able to use my Windows 8 OS drive after changing the secure boot strategy?

  Any help would be appreciated to greately.

  Sincere greetings

  DJ

  Hello:

  You have to enable the legacy mode and disable start-up secured in the BIOS to be able to install and run W7.

  Please see this link to find out where these settings... this references adding a video card, but this is how you change the settings no matter why you need to change.

  http://support.HP.com/us-en/document/c03653200/

• need a laptop keyboard and hard drive HP product number

  Hi all!!!

  My laptop keyboard and hard drive does not properly and I need to replace the two points. but I do not know the exact number of the product of the keyboard and the disk hard drive.  A knowledge of the product number please help me.

  Product model: HP Pavilion g6 - 1011TU Notebook

  Product number: LQ893PA

  Thank you

  Migas

  You will find figures for the product here in the service of maintenance & guide for the laptop G6.  As far the hard drive will I highly recommend that you use SATA instead of SATA2 or SATA3 for the best compatibility with the interface of disk on the system board controller.

• Is it possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

  I wonder if it is possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

  If 'yes', I guess I have to go for a SATA SSD if there is. But I have to worry about other specs?

  If 'Yes'... what could be.

  I googled my question but no answers... so I ty Wizzards :-) Forum

  @Lord_Nikon

  In fact, this is not true. As long as he uses a large SSD enough it will be able to use the recovery media. I suggest using a SSD of 256 or 512 GB if budgeted for the upgrade...

  He doesn't have to make a Windows 7 installation USB drive and use the activation key license on the certificate of authenticity from the PC Windows to perform a cleanup to install.

  One of them should be on your PC. The Prodct key is what is needed for installation and activation online.

  

• need an exact model of the PCI communications controller driver

  Mr President.

  my model is G62 B39 SE

  WINDOWS 7

  64-BIT

  HARWARE ID IS

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C & REV_06

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C

  PCI\VEN_8086 & DEV_3B64 & CC_078000

  PCI\VEN_8086 & DEV_3B64 & CC_0780

  Please I need an accurate model of the PCI communications controller driver

  Hello

  It's a system driver wise called "Intel Management Engine Interface (MEI) ' as mentioned in the following link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-83746-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5040732 & sw_lang =

  Please download the exe on the link above and install on your machine.

  Kind regards.

• Need administrator rights to install the program, but I am the administrator. What am I doing here?

  I am trying to install a program, but I get the message that I need administrative rights to install sign out and then sign in as an administrator. But I am the administrator, so what do I do? Why do I get these messages when I am the administrator and I have administrative rights?

  I'm trying to install Pinnacle Studio 9. It ran fine under XP. Is it possible to install as XP application? I am at a loss and I need some suggestions.

  I am running Windows 7 Home Premium.

  Right click on the shortcut to install, then click "Run as Administrator".

• I need a button to activate the audio and trigger an object, is it possible?

  I need a button to activate the audio and trigger an object, is it possible?

  I guess it depends on exactly what you mean when you say "trigger an object. If you mean to show a hidden object, with advanced actions, it is easy. Just create an action that would first start playing the audio then reveal the object.

  If "trigger an object" means something other than to show it, please post back with what it means for you.

  See you soon... Rick

• Downloaded the trial version of Acrobat DC. Now cannot open any program acrobat. I get the error message when needed to connect: connect to the internet and try again. Computer is out of connection or your computer's clock is out of adjustment

  Downloaded the trial version of Acrobat DC. Now cannot open any program acrobat. I get the error message when needed to connect: connect to the internet and try again. Computer is out of connection or your computer's clock is out of adjustment

  Log, activation, or connection errors. CS5.5 and later, Acrobat DC

  Mylenium