HP Pavilion dm4-1024tx Enterta: upgrade to 8 GB of memory and is blue screen problem

Product: HP Pavilion dm4-1024tx Entertainment Notebook PC
Product number: XC651PA
 
I have corsair Vengeance ram 8 GB (CMSX8GX3M1A1600C10) that as a result of the configurations as mentioned below:
 
SPD 9-9-9-24 latency
SPD speed 1333 Mhz
SPD voltage 1.5V
PC3-12800 (1600 MHz) memo speed
Tested latency 10-10-10-27
Tested 1600 Mhz speed
Tested voltage 1.5V
 
It passes the test of memory BIOS.
 
BIOS VERSION: Hewlett-Packard F.27, 21/12/2011
 
 
But when I boot windows 7, it shows the windows symbol and then it shows the blue screen with the error
 
STOP: 0X0000007E
 
If I replace memory corsair with the memory that has been delivered with the laptop the system only works very well.
 
Corsair memory is not compatible with the system?
 
I have a dual boot and installed ubuntu on this subject. Ubuntu loads perfectly fine, but after a while the system restarts automatically (IE open application).
 
I tried memorytest86 to test the memory, but the application continue to crash and reboot and does not provide any results.
 
Help, please.

Advertisement

The RAM is not compatible. The system allows a maximum total memory of 8 GB and uses DDR3-1333 which downclocks at 1066 speed. You cannot use a single module of 8 GB. 4 gigs is the large single module supports the system. I suspect the memory that you have will work fine if you had modules of 2 x 4 GB instead of a single module of 8 GB. That's why memtest is not finished. The controller memory motherboard is not able to take up 8 GB of RAM by a single channel.

Tags: Notebooks

Similar Questions

  • Pavilion dm4-2180us: wifi Upgrade on Pavilion dm4-2180us to 802.11ac card

    I have a hp pavilion dm4-2180us.  I want to upgrade the wifi 802.11b/g/n to ac 802.11 card.  Can I do this? I would like to know supported faster cards for my laptop. It would be a great help!

    My current card is Intel wifi link 100 bgn

    Thanks in advance.

    Hi @barbsduck,

    Welcome to the HP Forum!

    It's a great place to find answers and advice! You have the best experience in the HP forum, I would like to draw your attention to the HP Guide's Forums:

    First time here? Learn how to post and more

    I understand that you want to upgrade your wireless network to a 802.11 ac adapter. When I checked the guide service and maintenance for your laptop for recommended replacements, there not a listed 802.11ac.   Please see Chapter 4, page 40 for recommended replacements:

    HP Pavilion Entertainment PC Maintenance and Service Guide of dm4

    It is a big question other clients may also be question, please click on the ""Accept as Solution " if you feel that this post has responded to your request." You can say thank you easily by clicking on the ""Thumbs Up " below!"

  • Pavilion dm4-3055dx Entert PC: Beats Audio Driver

    Looking for Beats Audio Driver for Hp Pavilion dm4-3055dx Entertainmant PC

    Hello:

    The audio Beats is supposed to be installed by the IDT audio driver on the support page and the driver of your laptop.

    Details

    This package contains the driver that allows Audio IDT high definition (HD) in the notebook models that are running a supported operating system.

    File name: sp56172.exe

  • HP pavilion d4790y displat a bands and error blue screen

    HP pavilion d4790y displat a scratches, then blue screen error "cannot reset the display driver and recover from timeout failed" running GEForce 7500LE w/tv, DVI output, VGA has my card that went wrong? only to start in safe mode under vista home premium CPU Intel Dou processor E6700 2.66 GHz SATA hard

    Hello

    Try another monitor and cable on your PC in order to eliminate the PC as possible problem. You can also try your monitor and cable on another PC.

    Open your PC and see if the fan on the video card.  It can be full of dust.

    If the card turns out to be defective, must you output s-video port? If so, then look at this 9500 GT from NVIDIA.

  • HP Pavilion 17 j7b57av: need of repair to install the memory and hard drive

    How can I access my memory and hard drive to add memory and upgrade to a larger disk?  I do not see on the bottom cover access ports, which suggests low overall coverage needs to be removed, but there is always something that is in the manual of th, and I can't find a service manual.

    Please click the links provided which might come handy below

    http://h10032.www1.HP.com/CTG/manual/c04402649

    Hope this helps, for other queries in response to the post and feel free to join us again

    * Click on the white button on the right to say thank you Thumbs Up *.

    Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

    Thank you

    K N R K

    Although I am an employee of HP, I speak for myself and not for HP

  • Upgrade Alienware 17 r2, graphics, memory and SSD; heating system and stops

    I tried to find information on the upgrade from my old system of r2 to Alienware 17 with new graphics, memory and an SSD, but I've been to find contradictory information on it, and if I would still be able to upgrade my graphics.

    My current setup is:

    Computer model
    M17x
    OS version
    Microsoft Windows 7 Home Premium
    Processor
    Manufacturer
    Intel Core i7 CPU M 620 @ 2.67GHz
    Clock speed
    2.7 Ghz
    L2 Cache size
    256
    Memory
    Available memory
    35.50%
    The file size of the page
    10 048,7 MB
    Available Page file
    85.84%
    Virtual memory
    10 048,7 MB
    Available virtual memory
    63,04%
    M1
    2 048,0 MB
    M2
    2 048,0 MB
    Network card
    Storage
    Material
    Type
    Description
    CD-ROM/DVD-ROM readers
    Optiarc DVD +-RW AD - 7640S
    Disc players
    ST9250410AS
    Graphics cards
    AMD Mobility Radeon HD 5800 series
    IDE ATA/ATAPI controllers
    Intel (r) 5 Series 6 Port SATA AHCI Controller
    Keyboards, mice & pointing devices
    Synaptics PS/2 Port TouchPad
    Compatible mouse HID
    Microsoft Hardware USB mouse
    Compatible mouse HID
    Monitors
    Generic PnP monitor
    Sound Devices
    IDT High Definition Audio CODEC
    AMD High Definition Audio Device
    USB controllers
    Intel (r) 5 Series/3400 Series Chipset Family USB Enhanced Host Controller - B 3, 34
    Intel (r) 5 Series/3400 Series Chipset Family USB Enhanced Host Controller - 3B3C

    First of all, the graphics card can be improved and if so, should I go with?

    Depending on the type of memory I thought to install is:

    Crucial Ballistix Sport 16 GB DDR3 - 1600 PC3-12800)

    I heard that 8 GB was supposed to be the max, but that was only because it was all that was available at the time, the system was released and that others have used up to 16 GB.

    It will work or is there another suggestion?

    Thirdly, the SSD I plan on installing is:

    Crucial BX200 480 GB SATA III 6 Gb/s 2.5 "Solid State Drive CT480BX200SSD

    Still, I read the system never was not originally designed to support SATA III but if you use BIOS version A09 it would work.

    Is that correct or suggestions?

    The last two things I was wondering was that the system overheat easily and stops, to rebuild the thermal paste on the CPU and heatsink help correct this?  As well as to clean the fans, of course.  Or are there other options I should look into?

    Anyone know where to buy a new adapter power for this system as well?

    Thank you in advance for any help you can provide me with.

    Hello.

    First of all I would like to ditch the 620M processor, it's i7 below, you can get and dual-core only, not quad.

    You should be able to find an i7 820QM at a reasonable price, these days, 920QM or 940QM would be even better, they were the fastest available for this model.

    Once you have upgraded the CPU to something on an i7 720QM you can upgrade you RAM to 32 GB at 1333 MHz with no problems, if you want faster than 1333 you need to adjust overclock settings in the system BIOS.

    You have two HDD slots, up to any size SSD 1 TB plug-and-play (or to the more require very few adjustments BIOS) Firmware may need to be updated but also that it should be OK, just stick with an alienware used as Samsung brand, and if you can get one from the SSD slightly more older you might save money , you don't need a model 'latest and greatest '.

    Upgrade your GPU in the M17xR2 model can be a pain, the fan control is terrible and to really improve and play safely, you should probably use HW Monitor, so you do not cook your cards.

    Memory the AMD maps are more lenient when it comes to bi - GPU - I think remember me some upgraded GPU not X shot or SLIing in this model, but now is earlier in order not to forget.

    The M17xR2 is a very popular model, with thousands of people, the GPU upgrade - you can having to sort through the garbage to find the jewels but the info you need should be available if you do a search on google

    NotebookReview Forum would be a great place to start, 99% of the info you need should be there, the other 1% proably will be on techinferno.

    Guilbert - I still think that the M17xR2 has been one of the best they have done...

  • HP Pavilion Slimline s5298d had blue screen problem. Error: IRQL_NOT_LESS_OR_EQUAL (a).

    Hello!

    Can someone solve the blue screen of my PC problems?

    My PC always appear blue error screen especially whenever I stop PC.

    Error message: IRQL_NOT_LESS_OR_EQUAL (a).

    Arguments:
    Arg1: ffffffe5, memory referenced
    Arg2: 00000002, IRQL
    Arg3: 00000000, bit field:
    bit 0: value 0 = read operation, 1 = write operation
    bit 3: value 0 = not an enforcement operation, 1 = performance operation (only on chips that support this level of State)
    Arg4: 820d3a6a, address memory
    The blue screen issue can be caused by ntkrpamp.exe (nt! ExpScanGeneralLookasideList + 22)
    PC model: HP Pavilion Slimline s5298d
    Operating system: Windows 7 Home Premium 32-bit

    Hi once the device is powered keep tapping F2 button then start the hard drive & test control memory if a test fails, you will need to replace the part if test passes following the steps below. Then you can try the F8 key when the power is on and try the last known good configuration. If this does not work try start repair and try to repair the unit. If these options above does not work you can try to do a system recovery restore or F11 before this please back up your data as it will be lost.

  • Pavilion dm4: Windows 10 upgrade fails with the message error "we couldn't update the system reserved partition."

    Both HP and Microsoft indicate my laptop was ready for the upgrade to Windows 10, but when I tried to do the upgrade there not - several times - with the error message of Microsoft that "we could not update the system reserved partition."

    What should do?

    Other threads of error indicate the system reserved partition must be larger.  This partition is usually small.  Try making at least 400 MB instead of the 100 MB to 250 MB it is probably now.

  • HP Pavilion DM4 1219tx: Ram upgrade

    Please tell me if my laptop supports DDR3 1600 RAM, 8 GB capacity.  My 64-bit operating system and currently has 2 x 2 GB RAM.

    My processor is Intel (r) Core i5 CPU M 480 @ 2.67GHz

    My Motherboad following details

    Tip: Hewlett-Packard 162 58.28
    The bus clock: 1066 MHz
    BIOS: Hewlett-Packard F.27 21/12/2011

    Hello

    You have a fsb of 1066, but supports your 1333, so the installation memory 1333 with will run to 5:4 quite happy.

    Kind regards

    DP - K

  • G7 HP Pavilion laptop: Hp Pavilion G7 for computer upgraded to Windows 10 laptop-setting and no bass

    I have upgraded to Windows 10 Friday 7.28 and don't have now no bass sounds. I listen a lot using Itunes.It is not Itunes because all equalizer settings work. I tried t update drivers and he saiys that the latest drivers are in the system. My laptop

    is late 2012.

    Partz

    Look at the same problem with windows 8. There is a difficulty.
    Control Panel, hardware and sound, press speaker, properties, advanced, turn turn off audio enhancements. It should work.

  • HP Pavilion Slimline S5 - 1050d: Upgrade of RAM - single channel memory


    Hey, I want to just update. I installed another 4 GB of RAM with the same features (I decided to buy online).

    It works and BIOS shows two-channel after 2 slots taken.

    So, I guess he showed single channel because only simple slot taken.

  • HP Pavilion dm4 / Windows 7 - all wipe them outside the system and removed all HP programs

    So my computer just got back from the repair shop and I had to start with a blank slate. He removed all HP programs, including the program Pass Simple and webcam (I forgot what it's called). I tried to reinstall Simple Pass AND the new version, and none of them would not detect the sensor. I tried to find drivers, but no luck. Any help for the download of the two missing programs?

    Hello

    There is an excellent guide in this regard on the link below by Daniel_Potyrala.

    http://h30434.www3.HP.com/T5/notebook-operating-systems-and/HP-SimplePass-identity-protection-validity-fingerprint-and/TD-p/742013

    You will find all drivers for your laptop here.

    Kind regards

    DP - K

  • Pavilion dv6: blue screen problem

    GET THIS EACH THEN & NOW THE SCREEN AND MUST SHUT DOWN LAPPY. PLEASE HELP WITH THE SOLUTION!

    HI @Ayushi_kh

    Thank you for your response.

    Here is a link to the HP Pavilion dv6 Notebook PC. Please see Chapter 4 for removal and replacement.

    When I was browsing through the maintenance and service guide, I noticed you have switchable graphics.

    That being said, I suggest you do a recovery in factory.  This will reinstall the drivers of graphics cards correctly and I hope to solve this problem.

    Performing a recovery of system HP (Windows 7)

    During the recovery, there is an option to backup your personal data if you do not have a recently I'd do one now to avoid any data loss.

    Restore files that have been supported to the top using HP Recovery Manager (Windows 7)

    If for any reason any recovery did not resolve the issue please provides your exact model of DV6.

    How can I find my model number or product number?

    Good luck!

  • Under Win 7 64 bit I've recently upgraded to IE 10 (32 bit) and am now having problems launching SAP web page

    Most of my access works with the exception trying to load a list of customers from the existing web page

    Try the 'Compatibility' display option: http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-10

    J W Stuart: http://www.pagestart.com

  • HP Pavilion dm4-3005 serious bug BIOS/drivers - ACPI.sys blocks constantly DPC to 3 milliseconds

    Some of our users reported problems with the HP Pavilion dm4, Intel i5, portable audio beats, so we bought such a system for the test, a HP Pavilion dm4-3005. The OS is Windows 7 Home Premium 64-bit.

    The questions were dropouts sound while using the software and USB audio interfaces that we do.

    Now, we have confirmed the questions and analyzed the cause behind it.

    The computer suffers from a DPC latency bottleneck, that fires continually in the OS ACPI.sys driver.

    ("CPD" is a regular work of pilots (Deferred Procedure Call).)

    Each DPC planned by each driver must always end quickly (less than 100 microseconds), or it causes a bug which acts as a bottleneck. When a long DPC runs in a driver, all other drivers are often necessarily suspended, for example, on a machine that behaves in the way reported, Windows can not reliable service all the drivers that need to run more often than once every 3-4 milliseconds.

    Low latency is necessary for all reception record, DAW, music app, software synth, as well as pro audio interface hardware drivers.

    Because of the congestion, they all suffer from heavy sound artifacts more use cases / underallocations for the pilot of the audio interface. This includes our products but also in any other software low latency and USB audio interfaces.

    HP Pavilion dm4-3005 has in this way from the factory, and no matter what drivers are disabled or set to date.
    I ran all the critical updates for installation of Windows 7 Home Premium 64-bit.

    I downloaded and installed all the updates driver from HP support.

    Finally, I also downloaded the BIOS update that available to HP support.

    I also followed several guides to address these issues, including advice prevailing to disable the driver "ACPI Compliant control method battery" in Device Manager (Edit: filled in the name of the pilot.)

    Does not the initial problem.

    I guess it's a bug in the BIOS - which has yet to be resolved by HP or their partner of BIOS for this product.

    I have the computer factory reset and ready for testing your solution, when it will be available.

    As it is now, we must warn our users of these systems because of their unusable latency.

    HP is aware of this problem?

    Thank you very much

    John Engstrom

    Developer

    Propellerhead Software

    Hello world

    I have good news for you, dm4-30xx users!

    The new BIOS is completed and will be published shortly by HP (need to package configuration file and write the documentation now...). The update of the BIOS version will be the F.0B.

    However, I have access to the "raw" version of this new BIOS. I can send it to you if you ask me, but in this case, you will assume any bad use of this file. In this case, please send me your mail by MP.

    The official release will not take much time, so I think it's best that you wait.

    Best regards!

Maybe you are looking for

  • My address bar has changed color in itself

    I use the default theme in Mozilla and today the address bar has changed color from clear blue to windows blue, and the arrows and the "home" button are white instead of black. Since I haven't done anything intentionally and don't want it to appear l

  • 7 HP upgrade to windows 10 stream

    Hi, I downloaded the update to windows 10 today, but when it comes to accepting Microsoft conditions I can't get the Panel "agreed." It is away from the screen and the only decline is visible about. I can't to the 'agreement', but in portrait mode or

  • Server 2008 R2 installation will not configure on DV7 series laptop

    I installed the Server 2008 R2 on a laptop DV7-7012nr. I upgraded the memory up to 16 GB. I deleted all the partitions, and then divide the hard drive into 2 partitions. Partition 1 is 7 442 Go Windows, Partition 2 is 256 GB server. When I install, w

  • Server web cRIO

    Hello I have a cRIO (with a 9014 controller) system, which was running 3.1 OR-RIO, and a web server based application, without any problem. Now, I went to the 3.2.1 format... I 2009 LabVIEW and NOR-RIO cRIO disk, install the new version of the softwa

  • How can I set up my printer with the internet to avoid the impression in this tiny print and language I don't recognize?

    I used to be able to print very well and then something happened and I don't know how to correct it. Not only, it prints in very small font and lettering I do not recognize but also wants to print many pages, that I'm not. Thx for all help to correct