HP Pavilion dv6-3103sa: HP Pavilion dv6-3103sa does not then illuminate that plugged

Hi - my HP Pavilion dv6-3103sa has recently developed a fault.

It lights up with the power cable connected to it.  So that the laptop starts I have to first remove the power cable.

Similarly, before you turn off the laptop, I need to unplug the power cable.

If I leave it plugged in and turn off the machine, I can't start at all. The solution is to remove the power cable and the battery, then replace the battery only and then turn on the machine.

I also noticed that with the removed battery and the power cable is connected, the laptop does not start again.

Watching the light next to the power cord plug when plugged in the cable it quickly flashes of white, to orange, then back - tell me no power isn't learning laptop in this State.

I also tried a different power supply with the same intensity from a mobile phone of similar work with the same results.

Please notify.

@ScatchyMonkey,

Hello and thanks for the display on the HP support forums.  The problem you are having is with the motherboard.  There is a part that regulates the power and allows the system to know if it is connected or not connected and if it failed, you will need to have it sent repair.  Here is the link that will help you communicate with the correct service.

Contact HP support.

Thanks again for posting and have a great day.

Tags: Notebooks

Similar Questions

  • HP Pavilion dv7t-3000 does not start

    My HP Pavilion dv7t-3000 does not start. I checked this article: http://support.hp.com/us-en/document/c01732674

    According to who, the error condition is: 'non-functional CPU.

    So if I buy a new processor and disassemble the laptop and replace the processor, it will fix the problem?

    Perhaps, but it is much more likely to be the motherboard. If the motherboard is bad, you can't trust the blink codes that it generates. Failures of the CPU but rarely occur. Motherboard failure happens all the time.

  • Pavilion Media Center does not restart after the full system recovery. get the error code 0 x 4001100200001005

    Pavilion Media Center does not restart after the full system recovery. created recovery disks when purchased new. get the error code 0 x 4001100200001005

    Original title: recovery problem

    Hello

    According to the HP Support Forums, this error may be to do with the hard or for other reasons.

    You never have it replaced with a no HP bought in car?

    Read these threads HP on your error code:

    http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/recovery-disk-error-0x400110020000-1005/TD-p/22936

    http://h30434.www3.HP.com/T5/desktop-recovery-reply-only/trying-to-recover-an-old-PC-error-code/TD-p/964509

    If the original hard drive, press F11 at startup to start the process of recovery partition HP, did you recovery disks of.

    See you soon...

  • HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

    HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

    The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

    (1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

    (2) I tried to change the power adapter too.

    The problem is that it is.

    Your advice is very much appreciated.

    Thank you best regards &,.

    Zia

    Dear customer,

    Welcome and thanks for posting your question on the Forum of Support HP

    It seems that you are not able to turn on the laptop and tried to solve the problem

    Please perform steps listed to find out if it is a hardware or software problem below:

    1. remove all cables and devices, disconnect them and try to turn on the device

    2. check the LED light situation and ensure the action of the spring button / stop is normal

    3 Exchange with a well known power cord and the AC adapter

    4 Pack no adapters are available, check if the power adaptor is slightly warm

    Note: This will give us an indication that the power adapter could be good

    5. do you know if the laptop was in battery or power adapter when you used the last time

    Note: Make sure that there is no spill of liquid or cutting

    6. check if the Port of the AC adaptor is loose/broken

    Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

    Hope this helps for other queries to answer the post and feel free to join us again

    * Click on the star of CONGRATULATIONS on the left to say thank you *.

    Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

    Thank you

    K N R K

    I work on behalf of HP

  • The sound on my HP Pavilion G6-1a19wm does not work

    Hi the sound on my HP Pavilion G6-1a19wm does not work.   His "only" works when you use the audio plug with external speakers.   I tried to uninstall the driver, update the driver, microsoft fix - it and troubleshooting steps.  audio device present in the Device Manager and supposedly working properly, mute is "not"on."  visually everything audio related things suggest that the audio is fine and troubleshooting finds no problem... what else could it be?

    Hello

    Try the following.

    Download IDT Audio Installer on the link below and save it in your downloads folder.

    http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55036.exe

    One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

    When you're done, shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

    Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

    Allow Windows to fully - charge it will automatically load an audio driver, but let just this complete.  Then open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  Once this done, do a right-click the speaker icon in the taskbar and select playback devices.  Left click 'Speakers and headphones' (or speakers/HP) once to highlight and then click the Set Default button - check if you now audio.

    Kind regards

    DP - K

  • XJ437PA #ACJ: Pavilion DV6 - Audio does not

    Hello

    The audio has stopped working in my laptop since these days. It started with the audio does not not intermittently, but he has completely stopped working. I shared my PC specs below:

    Product name: HP Pavilion dv6 Notebook PC
    Product number: XJ437PA #ACJ

    Processor name: Intel (r) Core i3 CPU M 370 @ 2.40 GHz (2 400 MHz)

    I went through this forum and tried a few things:

    (1) to reinstall the codec IDT high definition

    (2) using the file available in the Recovery Manager

    (3) using the MicrosoftFixit

    But the problem is not yet solved.

    Can you please provide some suggestions?

    Thank you

    David

    Hi David,

    I would suggest you try a slight variation on the first two methods.

    Download IDT Audio Installer on the link below and save it in your downloads folder.

    http://ftp.HP.com/pub/SoftPaq/sp47001-47500/sp47393.exe

    One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.

    Right-click on the Audio display Intel entry and select uninstall - this time check the confirmation box to remove the driver and continue the uninstall.

    Then, right-click on the IDT device and select uninstall - for this entry, also check the box confirmation to remove the driver and uninstalling.

    Once completed, restart the laptop.

    When windows has reloaded, open your download folder, right click on IDT Installer and select "Run as Administrator" to launch the installation. Once done, restart the laptop.

    Any improvement?

    Best regards

    DP - K

  • Pavilion dv6: laptop does not

    I was given a Hp pavilion Dv6 some time ago and I tried to run but I don't know what's wrong with him

    When I plug in the power ring lights and when I press the power button on the fan and other lights come on but the screen does not work. When I press Ctr alt delete it restarts and now the backlight of the screen lights up but nothing appears. When connected to an external monitor a cursor appears in the corner of the screen for a few seconds then disappears, I tried to put disc in there but I still nothing No bios or the empty start screen.

    Thanks in advance if you can help me!

  • Pavilion dv6 Webcam does not?

    I have a Pavilion dv6-1030 ca laptop, and since a few weeks, I had trouble with my webcam. When I open the HP MediaSmart Webcam, I get the following error message: "no video device detected. Please connect a video device to your computer. If you are using a built-in camera, please make sure that it is turned on. "I have a built-in camera, and (usually) lights up when the webcam application opens. I am running Windows Vista with SP1 and tried many things to fix it, nothing helps. The webcam does not appear in the device, under imaging devices Manager, nor any of the Hubs USB root. So far I have tried:

    -Reinstalled the drivers of USB root hub

    -A tried to fix the solution in the BIOS (that another thread suggested)
    -A tried to use Recovery Manager to reinstall the driver (wasn't in the list)

    -The recovery disks created to solve the problem (it didn't)

    -Updated the MediaSmart Webcam software

    I'm at school right now, and I can't really afford to give my phone to obtain compensation for three weeks since I have exams coming. Any help would be appreciated! Thank you!

    Message edited by annabelle89 on 27/07/2009 20:30
    Message edited by annabelle89 on 27/07/2009 20:31

    Don't pay fees to repair overpriced... it happened to dv6 my boss, lift just the frame surrounding the top and sides.  You don't need a crowbar on the bottom of the frame.  Use your nails under the inside edge of the frame, they have adhesive tape double-sided, so it can be a little difficult to dislodge.  Lift slowly so that the band can separate on its own.  Don't force quickly or you could damage it.  Make sure you are not prying the metal frame silver of the LCD, only the black plastic frame.  There are hooks plastic that will make a click sound when you lift up the frame, it will need a strength, so don't be afraid if you hear the wink, he should be able to put it back together if you did it correctly, otherwise you will need to use some tape to tape the rear frame, better than paying $100 +... haha.  Once you have pryed on the top of the frame and have access to the webcam module, you should see the cable going into it from the bottom, push the cable into the webcam, then see if the problem is resolved, the cable most likely just came loose.  If that solved the problem, I suggest to use something you can remove, as hot glue to hold it together, just in case the webcam really needs to be replaced, you can melt the glue wide and swap out.

    If your microphone works very well and just the webcam does not work, then the problem is most likely a driver problem, or the webcam itself somehow has been damaged, which is highly unlikely.

  • HP pavilion Dv6 laptop: does not start in normal mode, safe mode

    Hi all

    I have HP Pavilion DV6 laptop with windows 7 Home premium 64-bit OS. It was working fine up until two or three days.

    After that some software upgrades, it has stopped booting.   When I tried to start it in safe mode, it stops at disk.sys.

    I don't have win 7 OS CD or recovery CD.  So I downloaded the trail version of windows 7 SP1, I want to install this, but he is suspended the windows logo.  I Googled it has bitten, I loaded a linux kernel and access the hard disk.  I backed up all the files required by using this boot of linux.

    I don't know what to do now?  What is the problem with my system. When I ran the drive diagnostic. It was a failure. That means that I can't use this HARD drive?

    Any help is greatly appreciated.

    Concerning

    Stéphane

    Hi stephane,

    Well the error code certainly would indicate that the player began to fail, but just in case, you might try to wipe the entire hard drive first and then reinstalling the operating system as described below.

    Download and install Killdisk on the link below - (this application will write zeros to the entire disk).

    http://Software.LSoft.net/KillDiskSuiteFree-Setup.exe

    Download and install ImgBurn on the link below.

    http://download.CNET.com/ImgBurn/3000-2646_4-10847481.html

    Access the application of disc kill you have installed in all programs, open the main folder, then select Bootable Disk creators, then the BACK Bootable CD Creator that will burn the ISO on a blank CD bootable.

    During the following process do not worry about all warnings as your Windows 7 installation disk will reformat the HARD drive.

    Insert this CD into your PC which is unable to load the operating system properly. Close Notepad, and then start again to boot from the CD of Killdisk and follow the instructions on the screen to kill disk.

    A brief description of the process here is Killdisk.

    Use it to wipe the entire hard drive, Select (80 h) and press f10 (you will also need to type a confirmation and press enter) - ( This will make sure to include all of the partitions , and then start the process - this may take a few hours!).

    When the process is complete, remove the CD of Killdisk and try to reinstall Windows 7.

    If it still does not work, I think your only option is to replace the HARD drive.

    Kind regards

    DP - K

  • My HP Pavilion dv5 1126em does not boot the system.

    My laptop does not continue to boot the system, when I press the button it starts feeding and then he shows me the HP logo in the lower left corner "Press ESC for Boot Menu" does not continue, and stop there and does not respond to any button only for the power button then it turns off, I tried everything. It happened after wile recovering the session of my recovery disk.

    Please help me identify what the problem is?

    I hope I'm wrong, but it is quite possible that your hard drive is damaged and must be replaced. I'll tell you why I think so.

    Last year at the end of December, I had the same problem with my HP Pavilion dv6. When I pressed the power button only the HP logo and the "press ESC for Boot Menu" appeared. I wasn't able to get into the BIOS or to do anything else. The laptop take-out hung on the HP Logo. I gave the laptop HP service and they told me that my hard drive has disappeared and they replaced. The strange was that my laptop was fairly new, I've had for 3 months. The good thing is that they have replaced the hard drive for free, because it was under warranty.

  • DV6-2150us-> does not supply power to the top.

    Hello

    I have a computer laptop dv6-2150us pavilion which, for some unknown reason, does not. I was working very well. I stopped and would not start in a couple of hours. I kept the power button down as others have suggested, but nothing happens. A laptop is dead.

    How to deal with a computer that won't even turn on.

    One thing I think is to change the battery. Before the power loss, my battery needed replacement. I had to keep the laptop plugged in to work. I couldn't work on the battery.

    I would appreciate any ideas. Thank you

    Kind regards

    Sam

    The first thing, remove the battery and unplug the power adapter and leave it without power for a minute.

    Then plug the AC adapter in (be sure to leave the battery) and see if the laptop. If it doesn't, the next test would be to check the power adapter (reconnect it in community/points of sale). If this still does not work, you will need to try another adapter to see if the laptop turns on.

  • My HP Pavilion g6 fan does not work.

    I bought a HP Pavilion g6 2230tx a few months back and its cooling fan has stopped working.
    It was working fine, but the problem started when I played Euro Truck Simulator 2 full settings. The cooling fan has been throwing a large amount of heat and the fan was moving quickly, but I continued to play. Later that day, when I turned on my laptop, it showed an error which was: "the system has detected that a cooling fan does not work correctly and continued operation can cause damage.
    Fan system (90 b)'.
    Then I turns off after 15 seconds.
    My laptop is under warranty until 2016-06-16 [YYYY-MM-DD] and the Security category is "guarantee of the factory." {Deleted personal information} & product number is C9L64PA #ACJ. Now my question is that how much HP will take to repair or replace my laptop fan. Will it be free? ;-)
    And I live in India.
    Thanks in advance
    Aniket Chauhan

    Dear Hüffer
    I tried what you say except clean it with compressed air and a paperclip. I'm going to send my laptop for repair and now I hope they'll work again.
    Concerning
    Aniket Chauhan

  • HP pavilion g6: fan does not

    My laptop fan does not work. What should I do

    Hello @AnilPaliwal780,

    Thank you for visiting the Forums from the HP Support! I see the fan on your HP Pavilion g6 does not work.

    To help, please let me know the Exact model of HP Notebook you use?

    I'll watch for your reply.

    If you want to say thanks for my effort to help, click on the "Thumbs up" to give me a "Bravo".

  • Pavilion 500: PC does not start.

    I recently installed Windows 10 preview alongside Windows Enterprise 8.1, due to the fact that I could not install the latest version of Windows 10 preview 10041 I tried fiddling around with my boot partition, consiquently I can't boot my machine at all is to say does not provide BIOS/UEFI & all I get is a blank screen.  I tried to start my 8.1 Windows Pro CD & nothing, infact my PC does not detect the CD at all.  I also deleted my partition to restore HP 'yonks' (plonker!) there.  Peuvent some please help?  I have three partitions on my drive, there are W10, we have W8.1 Pro and the third has all my documents & photos etc.  My boot default OS saw W10.

    Thank you for the additional information.

    I carefully read your original post.  I think your best option is a system recovery.  Given that you have deleted the recovery partition, you must order the HP discs:

    http://support.HP.com/us-en/product/HP-Pavilion-500-000-desktop-PC-series/5358992/model/5403158/document/bph07143/

    So, I suggest to use a second hard drive to install Win 10.  It is the best way for dual boot.  When you have two OS' are on the same drive there is a lot of room for error. especially when installing a less stable version.  Win 10 is exactly that.

    Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

  • Pavilion 15-e020tx: does not turn off pc portable hp pavilion 15-e020tx

    Hello.
    I have a pc hp laptop pavilion 15-e020tx. It does not turn off and does not wake up mode 'sleep'...

    I tried to restore my laptop to factory setting, updated everything I can, but it still does not work
    Could someone help me please

    Update the BIOS to the current version. A F.24. The direct link to the download is below.

    http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69897.exe

Maybe you are looking for