HP Pavilion DV6: at startup BIOS showing CPU fan has stopped working, but I checked the fan is in good condition

Similar Questions

• Pavilion g4: apllication of Catalyst Control Center: Host has stopped working...

  I get a pop-up window saying: "Catalyst control centre: host application has stopped working.". "

  It is written in the body of the box: "a problem caused blocking program woring correctly. Windiows will close the program and notify you if there is a solution. "
  
  I can't connect my games online as well. Please give a good solution

  Hello @Sailorswrath ,

  Thank you for your inquiry.

  What is your exact model of the Pavilion G4 you have?

  How can I find my model number or product number?

  There was a recent change before that happened?

  Have you tried running MS difficulty?

  Have you checked against viruses and malware?

  Here is a link to help test for a hardware failure.

  HP Notebook PC - detection of hardware failures (Windows 7, Vista)

  If it is a recent change, you can perform a restore to a well known date?

  HP Notebook PC - using Microsoft System Restore

  Good luck!

• HP Pavilion: Before port USB on HP desktop computer has stopped working

  My HP desktop computer is about 2 years old and has two USB ports on the front and a number on the back. I had no problem with any of the ports until I used a USB in the port now broken and caused a power outage that now this port doesn't recognize any USB device.  It says "USB device not recognized.  The last USB device you connected to this computer worked badly and Windows does not recognize. »

  I tried to uninstall and reinstall the USB ports on the Device Manager and have lived all the suggestions on the HP support site and the Microsoft support site. The defective USB key must have caused damage to the track. I hope you can suggest something that I can do to get it working again.

  Hello

  The only port on the front is damaged. The USB key must have damaged only this USB port. I'd like to reuse this memory bar.

  You need to replace the USB module, two ports USB 3.0 of housing as the two front ports use the same module and connections to the motherboard.

  You will probably need to go to HP for the part.

  You should be able to get access to the component by removing the front bezel. Remove the side panel also. You should see the connection of the cable and add him the USB 3.0 connector front on the motherboard.

  Jay

• Skype crashing on startup displays a message 'Skype has stopped working ".

  I saw several messages that have these same problems, but they seem to be older. I have version 7.12, the most recent and Windows 7. It was working fine, and then all of a sudden it no longer works. My husband updated his iTunes a few days ago and I think that might have been when the error started to appear. I'm not positive. But I tried many different things to solve this problem and nothing seems to work.

  Here are the details of the error:

  Name of the failing application: Skype.exe, version: 7.12.85.101, time stamp: 0 x 56088482
  The failed module name: unknown, version: 0.0.0.0, time stamp: 0x00000000
  Exception code: 0xc0000005
  Offset: 0x0d41c210
  ID of the process failing: 0x10e0
  Start time of application vulnerabilities: 0x01d1082c58549b77
  The failing application path: C:\Program Files\Skype\Phone\Skype.exe
  Path of the failing module: unknown
  Report ID: a44b6da5-741f-11e5-ad51-002354826e88

  Open this link in your Internet Explorer and update your Flash Player to the 19.0.0.226 latest version for Internet Explorer:

  https://get.Adobe.com/flashplayer/

• Office Pavilion Elite HPE message: AMD/ATI Video Driver has stopped working properly

  I have a Windows 7 Desktop HPE-410y, this morning, that the flag of the action center was at the bottom of the screen.  I clicked on it and there was a message: AMD/ATI Video Driver has stopped working properly.  He also said I should click on a link for a solution to this problem, but of course when I made the site of HP said that the page does not exist.

  Maybe say if you have in fact noticed nothing else Action Center indicator would be useful.  If it seems to you that the computer was OK and run satisfactorly, then perhaps he had already solved the problem.  Usually reviews can occur if a program did unexpected things and crashed the video driver, then the driver recovered.

  HP site can be set to an old page.  The real driver has not been updated recently on the HP site.

• My slideshow function does not work and the msg of error shows impgspl.ax has stopped working properly. Troubleshoot is confusing

  My question is explicit. I don't want to disable just etc. unregisted get the job of slideshow feature! Answers please?

  I was wondering why won't you try unsubscribing impgspl.ax?

• Use high CPU (35% average) while System Idle process CPU about 98% but frustrated by "[name of the prog] has stopped working".

  Hello

  I am trying to help someone with a laptop HP model g6-1202sa (Windows 7 Home Premium 64 - bit, another record at the end of the post).

  I think that Windows is now updated and drivers, but the problem remains also.

  The laptop has the symptoms mentioned in the title I found the Manager tasks.  Laptop fan is on a large part of the time, and the owner says that, during the execution of something more intensive than Skype for example of internet browsing, they get a warning from Norton on high CPU. Resource monitor shows that system interrupts are on average about 31% CPU.

  The results, I found the task manager has led to some research on Google, which in turn led me to want to run adksetup.exe (Windows Assessment and Deployment Kit) in the hope of discovering if a particular driver is causing the problem. (Various threads on the internet point to what is the way to go).

  However, after downloading adksetup.exe, when I try to launch it I get the initial screen of Toolbox and then 'assessment of Windows and the deployment for Windows 8.1 Kit has stopped working ". (Verification of the solution finally gives the only option to "Close the program").  Similarly, I have now discovered that if I try to look at the properties of the computer, i.e. start > right click on computer > left click on properties, I get "Windows Explorer has stopped working". Do more research on Google I find sometimes I get "Internet Explorer has stopped working" sometimes (Chrome is ok).  More out of curiosity than anything specific I ran AMD VISION Engine Control Center after right click on the desktop and ended with 'Catalyst Control Center; The host Application has stopped working".

  So before going any further, does anyone have any ideas what's happening?   I do not understand the problems 'has stopped working"in safe mode, but the high utilization of the processor with System Idle Process around 98% is still there.  It appears so that I can run adksetup.exe in safe mode while this would be the way to proceed and continue to try to tackle the problem of CPU?

  For the record, some of the things I've done along the way include update of Windows, updating drivers, running the file system (no violation of integrity) checker, a regular chkdsk ("CHKDSK discovered free space marked allocated in the master file table (MFT) bitmap. Correcting errors in the volume bitmap. Windows has made corrections to the file system").  Swapped the only module memory 4GB 2 x 1 GB modules I had to hang out, all the symptoms remained 4 GB then reinstalled.

  Thanks for the tips

  HP g6-1202sa Windows 7 Home Premium 64-bit

  4 GB of ram

  AMD A4 - 3300M APU with graphics Radeon (TM) HD 1900 MHz

  523 GB of free disk space

  WE

  Since the observer event logs, these are some of the problems

  Software connection of 1 hp mgr is damaged and needs to be installed.  There are literally hundreds (or even thousands of these errors)

  Cannot find the description for the ID of the event source hpCMSrv 5. Either the component that triggers this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.

  The failing application name: hpConnectionManager.exe, version: 4.1.23.1, time stamp: 0x4df7dbef

  2 - the description for event ID 0 in source AdvancedSystemCareService8 is not found. Remove

  3 - Media center is corrupt (updated)

  The description for event ID 0 in source MCUpdate is not found. Either the component that triggers this event is not installed on your local computer or the installation is corrupted.

  Workouts 4 - sky are corupt

  Session "SkyDriveSessionName" was able to start with the following error: 0xC0000022

  5 - the description for the ID of the event source BtFilter 26 is not found

  6 - hundreds of Cvhsvc.exe is a part of the virtualization Client Microsoft Microsoft Office Service... Errors

  The description for event ID 100 from source CVHSVC is not found.

  7. the description of event ID 3057 source client Application Virtualization Client cannot be found.

  As you can see there are at least a dozen of them which are probably related to the high utilization of the processor.

  The drivers are not updated (Bet you checked in the Manager device or with a sweeper driver as app)

  To be honest I don't see how SFC returned no breach of integrity account required to this type of problems.

  It might just be easier to re - install win 7, but I'm happy to help anyway

• Equium A210 - after that set BIOS to update the DVD player has stopped working

  Hi, since I have recently updated my BIOS, my DVD drive has stopped working on my Equium A210-1AS with Vista 32 bit.

  I tried the program fixme Microsoft who does not work, upper and lower register isn't here ether in regedit.
  Someone at - it solutions for getting the DVD drive working again?

  Thank you

  Hello!

  The CD/DVD drive is listed in Device Manager? You see an error code?
  If the drive is listed in Device Manager, you should try to remove it, and then restart the laptop.

  Try to load the default settings in the BIOS.

  Have you tried to remove the upper and lower filters by yourself? Here is the solution from Microsoft:
  http://support.Microsoft.com/kb/314060

  Good bye

• HP Pavilion dv6-WQ685UA #ABA needs a main battery replacement and is still covered by the warranty.

  Hello

  My HP Pavilion dv6-WQ685UA #ABA needs a main battery replacement and is still covered by the warranty.

  I always thought that this laptop can't run then 1 hour unplugged but still ran about 30-45 minutes before the battery is discharged (recommended HP). A few days ago I received this message when starting upwards:

  Main battery

  Failure ID-U360G0-000624-XD0002J-C0DL03

  Product ID-WQ685UA #ABA

  Replace the main battery.

  So here I am. How do I get a new battery, sent me? Thank you!

  Hello:

  It is a forum of consumer to consumer.

  Nobody here help you with warranty issues.

  You will have to contact HP support support.

  Contact HP on the link below for the country you live.  Select the option 'technical support after purchase.

  http://WWW8.HP.com/us/en/HP-information/summary/WW-contact-us.html

  Paul

• Pavilion dv6 fingerprint reader has stopped working

  My fingerprint reader has stopped working. I can open the Simple pass identification program but when I click on fingerprints, it indicates 'identity check' with an hourglass on the top of the icon of fingerprints, and no matter how long I wait, that's all that happens. All advice appreciated.

  -----------------------------------------

  Pavilion dv6t laptop 3100, Win 7 Home Premium 64-bit, 8 GB of RAM, processor i5

  "Where you go, there you are."

  Hi Mikey,

  Looks like you're running the Digital Persona of SimplePass flavor.

  Two things to consider / try, in order.

  If the reset works, you don't have to reinstall the driver...

  • Hard reset
  • Reinstall the driver

  Hard Reset:

  Sometimes, all you need to do is the computer suddenly.  This method works for a variety of connection and "glued" program issues.

  • Disconnect all the external devices first.
  • Remove the AC power and battery
  • Press and hold the power button while in the minus 30 seconds
  • Reinstall the power supply for the first start only * see Note
  • Power on - connect
  • Next time you shut down the system, replace the battery.

  * Note: You can ignore the little battery aside.  If you wish, replace the battery the first time and do it with her.

  =====================================================================================

  The pilot, from your Internet site:

  Validity fingerprint sensor Driver sp52354 V2.1.0.2

  • Install the validity sensor Driver installation package: it if called sp*.exe - the package will be most likely located in the downloads folder.  If you have control of "Admin", you can highlight the package and "double-click on ' to install it, otherwise just right-click, select"Run as Administrator"and install.

  I hope this helps!

  It's my pleasure to help.

  Say "thank you!" to the help by clicking on the star of Kudos to show your appreciation.

  Fixed?  Mark this message 'accept as Solution' to help others find the answers.

  Note: You can find "Accept as Solution" only on the threads started by you.

  Good luck!  Year of the Dragon!

• I received an error message after installation encyclopedia British and this application cannot be open.showing the "Startup MFC application has stopped working". How can I solve this problem?

  I received an error message after the installation of Encyclopedia Britannica and this application cannot be open.showing the "Startup MFC application has stopped working". How can I fix this?

  Hello

  always check the compatibility of vista programs on the link below

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

  If a program is compatible with vista you can try right click on the setup.exe and then by selecting run as administrator to install it

  It is not compatible with vista, you can try running it in a previous operating system mode

  This does not work for all programs

  read the information below

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

  ____________________________________________________________

  and read this information MS, too

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-the-program-compatibility-Wizard

• I received and after the British insatalling encyclopedia and this application cannot be open.showing the "Startup MFC application has stopped working". How can I solve this problem?

  I received and after the British insatalling encyclopedia and this application cannot be open.showing the "Startup MFC application has stopped working". How can I solve this problem? IM using Vista Home Basic 32-bit.

  It comes with Vista, upgrade install and activate Forum.

  Try in Vista programs Forum:

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/threads

  See you soon. Mick Murphy - Microsoft partner

• HP Pavilion dv7 6b51ea: GPU stuck at Intel, AMD GPU has stopped working

  A year ago, I received a notification of the CCC AMD the driver update and did. Since then, the 7400 m has stopped working and still did not so after;

  (a) rolling back drivers

  (b) reinstall the drivers from the HP website

  (c) using the system to factory settings restore

  After some research I found that the discrete GPU in HP laptops only works with the drivers offered by HP, but those who fail to solve the problem of too.

  I put Powerplay use Max Performance and even tried to disable ULPS, which of course failed because the system is locked ' dynamic single setting.

  Active power plan still shows as powerful, but it's the GPU integrated in use, not dedicated

  Also recently upgraded to Windows 10, had no problems but GPU problem remains

  AMD Catalyst Control Center poster always I have 7400M and hardware of MSI Afterburner monitoring shows his temperature to 45 c but 0% use of the GPU.

  When running games that allowed, with Powerplay can jump on the 7400 M, still work on the weak integrated Intel graphics.

  HP Support Assistant cannot detect all problems, troubleshooting

  HP Pavilion dv7-6b51ea

  Appreciate the help.

  Thanks for your help, very much appreciated a response.

  Assuming that I am in a bind.

  HP should not make laptops for gamers or those who buy specifically for the use of the dedicated GPU, if they cannot upgrade their GPU drivers dedicated by the manufacturer of this GPU IMO.

  Sister with a DV6 bought with my DV7 (2012) was lucky, I tried the update before she accepted AMD update notification

  Guess I will gift to a parent who does not require the dedicated GPU and I'll have to make sure my next laptop supports the amd/nvidia driver unlike HP updates of course

• Startup error message: "Microsoft Mobile PC presentation adaptability Client has stopped working".

  I recently tried to install SP2 to Vista, but it failed. I tried all the resolutions posted, but it is not always correct it. Later, I started my Vista (automatically restored to SP1) and it came with a mistake, "Microsoft Mobile PC presentation adaptability Client has stopped working". I tried searching on the net for similar problems, but I could not find any solution. He comes back every time you start, after that the background, shortcuts and the system tray loaded. This error started showing when I tried to install SP2, but he failed and returned to changes. I think that something could have gone wrong and that's why it shows this message.   Today I tried the system restore to the restore point JUST before I tried to install SP2, but it ALSO failed and brought me back to the State.
  I'm not sure if it's related, but I'm also no longer be able to use Windows Media Center, as every time I start it I immediately receive the error message "Media Center has stopped working".
  My computer:
  Gateway M6842B laptop
  Version of Windows Vista SP1 32-bit
  Intel Core 2 CPU
  T5300 @1. 73 GHZ 1.73 GHZ
  2.00 GB OF RAM

  Hi zensurferboi,
   
  First, we will check if we get error safe mode, start the computer in Safe Mode reboot and press the F8 key for about four to five times. You'll see the Mode without failure listed in the advanced window options, select Safe Mode, and then press ENTER.
   
  Check if the error mode without failure.
   
  If the startup error message does not appear safe mode, I recommend you to place the computer in a clean boot state, and check if the problem occurs in a clean boot state.
   
  To put the computer in a clean boot state, follow these steps:
   
  Perform a clean boot
   
  Note If the computer is connected to a network, network policy settings may prevent you from following these steps. We recommend strongly that you do not use System Configuration utility to change startup options on the computer, unless a support engineer Microsoft directs you to do so. This can make the computer unusable.
   
  a. log in the computer using an account with administrator rights.
   
  b. click Start , type msconfig.exe in the Start Search box and press ENTER to start the System Configuration utility.
  If you are prompted for an administrator password or for confirmation, type your password, or click continue.
   
  c. under the general tab, click Selective startup, and then clear the Load Startup items check box.
  (The box use the Boot file is not available.)
   
  d. on the Services tab, select the hide all Microsoft services check box and then click on disable all.

  Note Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use to restore the system with the existing restore points.
   
  e. click OK, and then click restart.
   
  Once the computer restarts, check if you get the error of starting.
   
  Reset the computer to start as usual
   
  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , type msconfig.exe in the Start Search box and press ENTER.
  2. If you are prompted for an administrator password or for confirmation, type your password, or click continue.
  3. On the general tab, click the Normal startup option, and then click OK.
  4. When you are prompted to restart the computer, click restart.

  If you don't receive the start-up error message after placing the computer in a clean boot state, follow the steps below in the link to diagnose the program or service that is causing the problem:
   
  How to troubleshoot a problem by performing a clean boot in Windows Vista
   
  http://support.Microsoft.com/kb/929135
   
  I hope this information is useful.
   
  Please let us know if you need further assistance.
   
  Concerning
  Rehman - Microsoft Support

• "Show my windows and tabs from last time ' has stopped working after software updated to the end of January or early February. Now on 12.0a2. Change options "Auora to start: ' no longer works.

  I use this feature for years and update Firefox/Aurora in the next few days, maybe a week, an update becomes available and everything suddenly ' show my windows and tabs from last time ' has stopped working. I can go to the Tools-Option-general tab and change "at Aurora startup:" to this option, or 'Show my home page (s)' and now the opening in a new tab single even though I have URLs there. This may mean that this bit is not read correctly. I'm not playing: config, but I watch a few spoken options in the Web and everything looked OK.

  I would uninstall and reinstall it if you think it will solve the problem. I updated Aurora again because this problem started and it remains broken. It is a system of XP with SP3

  PS: I have two other windows with a XP and the other Windows 7. When I had the problem on my primary XP System I stopped to make updates to other systems. Today I updated the two other systems with the latest Auora (skip one or two updates) and both work very well.

  The best way for me to trouble?

  Hey punchcard4rjw,

  Have you tried to start Firefox in Mode safe? Key 'shift' startup of Firefox. If it doesn't happen in Mode without failure, you should read the extensions, themes and problems of hardware acceleration to resolve common troubleshooting Firefox problems.

  If this does not work, you should look the article How to fix preferences that will not save.

  Hope this helps!