HP Pavilion dv9555eo notebook PC, I added = secondary HARD disk installation. How to configure in Configuration?

Similar Questions

• HP Pavilion g7-2010ne Notebook pc Windows detected a hard disk problem

  Hello

  I have a HP Pavilion g7-2010nr Notebook pc and two nights ago, I got a message saying "Windows detected a hard disk problem" and how do I back up my data and then repaired. So I tried it to my WD My Passport 500 GB external hardrive but as soon as he gets as 57% when the reverse said it will create a file system image, the backup fails I tired it three times to try different solutions I found on the help forums, but nothing helps and I don't know if maybe it's because the hard drive problem or another problem. Any suggestions are welcome.

  You can back up by using HP Recovery which should not have problems:

  This should help you:

  http://support.HP.com/us-en/document/c03489643

  You can stop it anytime before restoration starts if you encounter any problem.

• Pavilion 13-a113cl: the upgrade of the hard disk on a Pavilion 13 x 360 (13-a113cl) to an SSD

  I have an old 13-Pavilion x 360 with a 1 TB hard drive 5 400 rpm in it and wanted to know if I could pass it to an SSD. If so are there requirements the SSD must meet (such as under a certain storage capacity) and is there hardware and/or software addition that I would need to do this?

  Hi @devon-w! Yes, you can make your laptop with a SSD if you want. Once you get it, you can decide whether or not to perform a new installation of the operating system, or you can try to clone the current operating system installed with some cloning software. As far as I know, there is no limit on the size of the SSD, but I might suggest to keep your drive HARD current as an external storage location secondary data (movies, music, etc.), as long as it is not a failure of course. I hope this helps and good luck!

• HP Pavilion 400-434 Office: intelligent control of hard disk: failure

  Hello

  It all started when the computer would go blank right after startup, the HP logo would come upward, then 'auto repair preparation", more... Just empty. After reading the forums online, I did all the possible troubleshooting steps and at the end I did the SMART test... the result was:

  Verification of the processor: past

  Intelligent control of hard disk: failure

  Failure ID: RGD7MK-7HV7RC-9XJ16K-60BB03

  After obtaining these results, when I turn on the computer, it gives me a blue screen saying: drive SMART 1 error (301) and told me to test once again, that I did and got the same result as above.

  Here is some info from the computer:

  Model: HP Pavilion slimline 400-434

  Processor type: pentium (R) of the Intel (R) J2900 @2. 41 GHz

  Thanks for your help!

  Hi there @Brugalgirl

  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that your computer does not start successfully, and you found a Smart Drive 301 error code. I'm happy to help you with this.

  I checked the ID of the failure, you've posted and verifies that the error. Unfortunately, this means that your hard drive needs to be replaced.  In view of the fact that the system does not boot, it is likely that the hard drive is completely unreadable, but depending on what you have on this subject, it may be worth your while to check with a local computer service shop and see if they can help to recover data from your hard drive.

  If your system is relatively new and may be covered by the warranty, or if you wish to fix with HP for the guarantee system, you can call in hotline to make these arrangements. In this case, please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Otherwise you can look at a replacement hard drive yourself. If you have a set of recovery media, then you already have a factory image HP, which allows you to put in place a new hard drive with your original operating system. If is no longer, you have a set or did not have a set of recovery media, so you can see if there are not yet available for your model.

  HP computers - get HP recovery disks or HP USB recovery disc

  Let me know if you need help most. If it solves your problem, please mark this message as a solution.

• Problem adding a hard disk for Pavilion Elite HPE - 380 t

  Hello

  I am trying to replace my existing drive with a new WD 1 TB hard drive. So I intend to install the new WD drive as the 2nd drive, and then run the utility WD Acronis to clone the original to the new drive.

  However, when I install the new disk, the BIOS recognizes it, but I think it appears in Windows 7 such as D drive, but it does not work. When I run Acronis, he says that it doesn't detect any WD drive.

  I went into the BIOS and ran the test drive / self-test and it passed.

  I noticed that the SATA1 controller is enabled. He didn't check before installing the drive.

  The controller SATA1 mode is RAID. Not sure that it was previously.

  Oh, and I plugged the new drive SATA cable into the connector of the motherboard directly next to the SATA connector as my original drive.

  Everyone through this? Any suggestions?

  Thanks in advance,

  Steve

  You are right. It was the answer, sort of. When I started Windows 7, I went in the new disk drives and active management. I let the system assign drive letters. I then rebooted.

  Then when I came back to Windows, I was able to run the original utility WD Acronis True Image to clone my source drive to the new drive. When finished, stop the system, removed my original drive and the new drive my only drive.

  Everything works beautifully. I managed to replace my hard drive.

  Thanks for the tip.

  Steve

• Pavilion P6-2125 - adding additional hard disks

  Nice day.

  Can I add additional hard disks SATA internal? Is the power supply sufficient to allow this? In addition, this will void the warranty?

  Thank you, Joe

  Hi, Joe:

  When I look at the upgrade and maintenance of your PC guide, I don't get a hard drive Bay.

  So, I would say that your PC is not configured to handle more than one hard drive.

  http://h10032.www1.HP.com/CTG/manual/c03030603.PDF

  Paul

• HP Pavilion notebook PC A7H25UA #ABC g6 hard disk failure

  Hello

  My laptop started with this error message: hard disk failure: Q0FAJ2 - 66 X 756-MFGK1F-60F803 and past Q0FAJ2-66X74H-MFGK1F - 60CT 03. I run the hard drive test and they both failed.

  What can I do to solve the problem?

  Thanks for help me!

  You'll have to replace the hard drive. It is not as difficult as you might think. If you can do this:

  http://www.YouTube.com/watch?v=3AlMZFGwegE

  post then back and let us know the country you live, and we can help you find the best price on a good replacement and will guide you through software and data recovery/reinstallation.

• Pavilion DV7T Quad: image of the defective hard disk system restore

  I have Pavilion DV7T Quad 1 TB harddrive failed.  Defective hard drive has only 140 ~ GB on it.

  I have:

  (1) a complete picture of the external system WDC passport.

  (2) the DVD System Recovery to Win 7 64 bit disc 1 of 2 and 2 disc 0f 2 obtained from HP laptop acquired time.

  (3) repair disk for Windows 7 64-bit I had created "the way back when.

  I bought a new 240 GB SSD to keep this laptop as a backup.  Can I use 1, 2 or 3 to load files on the SSD (since the mechanical drive does not start)?

  bikerider1

  The link in my previous answer tells you step by step how to recover your system .vhd image files.

  If you found my answer helpful please say thank you by clicking on the icon of the thumb.
  If my answer has solved your problem, please mark it as accepted Solution. Thank you!

• HP Pavilion DV4-1275mx not display and no hard disk power activity

  I have a laptop HP Pavilion DV4-1275mx and when I turn on the computer, the fan turns on for a few seconds, then turns off, then the caps lock and the locking witnesses Flash on and outside.  The HARD drive on the front light shows any activity, what is the problem?

  Hello
  Click on the link below:
  LED white screen error codes

• B010ea Pavilion 23 all-in-in-one: the HARD disk specifications.

  I want to buy a drive enclosure external HARD drive on my pc trying to access files now pc does not. Can someone tell me if the drive is 2.5 or 3.5. I don't want to remove it until I have the enclosure.

  It's a SATA 3.5 hard drive ". You can replace it with a SSD if you want to increase performance.

  You will still be able to use the recovery media if the SSD has at least 160 GB of storage capacity

  Instructions for removal and replacement are at the following link.

  http://support.HP.com/in-en/document/c04275862

• Pavilion G4 1303AU: impossible to format the hard disk in any case

  I had 8 current enforcement windows on my system, then I thought to install linux (distribution mageia) on it. Before I formatted the entire system and created primary and extended partitions as well as some allocated space was left for linux.

  Then I installed windows 8 on a primary partition C. I installed linux on the unallocated space, and follow the steps in this video https://www.youtube.com/watch?v=SLu1NwsZr48

  I don't understand what was going on well.

  After I don't have grub GUI screen 2 so I rebooted the system and windows 8 started normally and automatically.

  Now, I decide to remove the linux partitions cz they did not appear on the home screen (for the dual boot option)

  I went to dskmgmt.msc and tried to delete the partition containing linux. The removal process has continued and eventually hanged. So I rebooted my pc and boom, the pc will not boot into windows 8.

  It shows crashes and win8 logo... I tried to format it, there also, it shows the start with logo screen and crashes in windows 7, it loads the files, comes up to the part where the logo builds up and crashes, tried mageia live cd also, there also it hangs on the splash screen.

  I tried default BIOS, I tried to format it using usb, everything.

  The hard drive gets detected as "laptop hard drive" in the bios... so I don't think that it must be a hardware problem.

  I hope there is a solution, because the laptop repair shops say that he died. I did not trust them because how can a partition physically damaged hard drive!

  Please respond quickly with a solution...

  I should be grateful!

  Piyushshekhar wrote:
  I used the seagate seatools too... but it hangs when I move the box and refresh!
  I know that my hard drive is not permanently damaged... He has just damaged its nd of mbr partitions, but not able to clean or to format these partitions... Also I don't have a big electromagnet to erase all data... So help

  You can refuse to accept it, but if Diskpart--> List volume or drive list does not see the drive when the data and power connectors are active, then the disk controller has not.  The hard drive is the material of the trash. Replace it with another new hard drive.

  An electromagnet not wip data from the hard drive. The hard drive uses magnets neodymium as p [art of its design.

• Secondary hard disk access

  After formatting drive (drive 0), and re - install Windows XP, I find no more the second hard disk (disk 1).

  The two discs are identified in bios, but only the main will appear in "my computer". In disk management, disk 1 is shown as foreign and dynamic. The only option is to convert it to a basic disk that will remove all information.

  What are my options to save the 30 GB of information on this subject.

  What types of drives are these, SATA, IDE?

  You have the jumpers set correctly, if they have? Master or slave, Cable Select No.

  The disk hard disk 1 was working fine before this?

  You can start with a bootable floppy and see if he can see both hard drives.

• Adding new HARD disk to the current setup RAID1 on PowerEdge T310

  Hello

  I have PowerEdge T310 with SAS 6/iR controller. I've configured as RAID1 with 2 x 500 GB HARD drive. Now I would like to add another disk HARD 2. Is it possible to do with the material current & configuration? IS SAS 6/iR support for additional HARD drive?

  Fauzi79,

  Unfortunately with the SAS6/ir you don't have the ability to develop. You must back up the data, delete the table, add readers, then reconfigure the table. After that, then install the operating system and restore the data. Sorry I couldn't give you the answer that you were missing no doubt, but it is a limitation of the controller you are using. If a Perc 6 / I installed then the expansion process is relatively simple.

  Let me know if this helps to clarify.

• Secondary hard disk to 'system '?

  I have several hard drives in my PC. Disk management tells me that the C: drive is "Boot, Page File, Crash Dump, primary Partition, as it should be, and I expect other readers to simply be"Primary Partition"normally." However, my drive H: is "System, active, primary Partition" - and indeed, when I unplugged once, the computer failed to load Windows.

  Why is this crucial disc to my PC run, and that means that I can't replace it? I think the drive has failed and if it means that I have to reinstall Windows 7 I will be very annoyed. If I need, I will be able to copy the files on it on a larger replacement disk and keep the computer running?
  Thank you
  Mike

  Hello

  By reading your description, why don' t you consider to use a third-party partition management tool to help you manage your disks? There are free programs that work. I just resize my partition and change the State of the partition that I needed (logical change of primary partition and then as active). Indeed, I have much enjoyed. Now I share with you what I found this software useful in

  I hope it can help you!

• Can I install and use your Adobe products on a secondary hard drive?

  Hello, I have my operating system files and the program installed on a 128 GB SSD and I have a 1 to secondary HARD disk. I want to avoid filling this SSD as much as possible. Y at - it an option during the installation of your Adobe products (which?) to install and use in a drive and folder on the secondary drive?

  Simply choose a custom installation and choose another location to a folder on your secondary drive. just be aware that some components such as the activation system and other shared stuff will be always installed on C:\, whatever happens. You are lgoing stil to lose at least 1 GB on your SSD.

  Mylenium