HP Pavilion Elite HPE 580t Int: SuperMulti DVD burner with LightScribe technology external ejection

Similar Questions

• HP Pavilion a6760y with SuperMulti DVD burner with Lightscribe technology

  Hello

  We had this Pavilion a6760y PC for about a week.  None of the software recognize the CD.  The device manager says that it can not load the disk due to a problem and gives an error 39.

  We followed the steps to delete upper and lower filters in registry as described in the HP troubleshooting guide.  Since Device Manager has always said that it cannot load the driver, I hesitate to go further - any suggestions?

  (1) make sure you have deleted filters down to the registry.

  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  After that DON 'T restart the pc immediately.

  Proceed to step 2.

  (2) uninstall the driver for the disc drive which shows in yellow code 39 of Device Manager.

  Very important step.

  Go to step 3.

  (3) now, you restart the computer.

  Go to step. 4

  (4) when you connect wait until 3 minutes and windows must be reinstalled the driver of rear disc and hopefully it should work.

  Message edited by c0rnel on 04/09/2009 16:23

• HP Pavilion Elite HPE - 580t: SATA HDD recognized and boots with the 2nd HARD drive, but not without

  Hello

  I have a Pavilion HPE - 580t with windows 7 installed.  The original drive (Drive1) has (according to Windows Disk Manager), a 100 MB system partition, a partition of 1 GB operating system and recovery partition.  The drive began to generate disk errors.  I added a second SATA (lecteur2), which has been recognized in the BIOS - it always appears at startup.

  I do not have to implement a system of lecteur2, but re-installed Windows 7 100 MB partition using lecteur2 as boot drive (not a cover), and it works fine, for most.  Reader1 still generates errors and slows down the office, but if I disconnect reader1, lecteur2 is ignored at the start, as the Bureau attempts a network boot.  I have confirmed in Windows OS is the start of the lecteur2, not reader1, but once again, lecteur2 is ignored as boot device if reader1 is not present.  I should add that this was the case when I was reinstalling the OS, I tried unplugging reader1 prior to re - install, but could not do and still access lecteur2.

  I tried to go up during the boot sequence in the Setup (F10), no change.  One additional thing - Setup (F10) is available that when reader1 is connected - F10 key has no effect at startup if reader1 is detached.  F10 Setup runs from the system on Disk1 area?  Any ideas on what I need to do to drop Drive1?

  Thank you

  David

  I can now tell you 2 things on your system.

  (1) the original hard drive is 1.5 TB and that is embedded in the tattoo of HP.

  (2) you cannot use a disk less than 1.5 TB as primary drive.

  Never seen a facility like this scheme start between readers.  The only way I see on this perdictament is to remove the 1 TB drive and let the process of recovery of re - install the operating system. Then immediately clone the original on a new disk of 1.5 or 2 t. Attention to not exceed 2 TB. Seagate and WD has a free program for Disk Wizard for cloning option.

• Pavilion Elite HPE-170 t - Wi - Fi adapter with antenna?

  I would like to connect to a desktop Pavilion Elite to a local network. The router is a Linksys EA3500 (802.11n technology). The distance between the router and the wireless adapter on the desktop will be about 30 feet with walls between the two.

  The office doesn't have an outdoor antenna. When I checked for network adapters, I found this: Realtek RTL8168 / 811D Family PCI - E Gigabit Ethernet NIC (NDIS 6.20).

  I use the computer for HD, movies, not for games. Should I buy a Wi - Fi adapter? And if so, which one of these adapters Linksys would give me better performance?

  1. a USB adapter - http://bit.ly/1tg8Cj1

  2. a card PCI adapter with antenna - http://bit.ly/1pzVpSt

  3. a USB adapter with antenna - http://bit.ly/1taGZd2

  Thank you

  Brescia

  Record office:

  Product name: BN496AV-ABA-HPE-170 t

  Product number: BN496AV #ABA

  Operating system: Windows 7 Ultimate 64-bit

  Hello:

  I have the AE3000 on two of my HP business offices.

  It has good reception and never had a problem with either of the units.

  I have a 2-story house with a finished basement.

  My Linksys EA 4500 router is on the second floor.

  One of my desltop of PC's in the basement.  The AE3000 on it, you get 4 bars of reception on the 5 GHz band and 5 bars on the 2.4 GHz band.

  Connection speed is 324 Mbit/s (out of 450) on my PC of basement on the 5 GHz band.

  Connection speed is 216.5 Mbps on bandwidth 2.4 GHz because I have this band the blended value that allows (wireless B and G) to connect legacy devices.

  It works fine on W7 x 64 and x 64 W8.1 (using the drivers W7 on the CD).

  It also comes with a 3' USB cable attached to a docking station so that you can position the camera somewhere for better reception.

• HP Pavilion Elite HPE - 580t: could not find driver for integrated Ethernet card for desktop HPE 580t

  This desktop computer has been through a number of operating systems and should now have 10 32-bit Windows (for other software support needs).  All right, except that it lacks drivers for connection to Ethernet (built-in) on board.

  I tried the approach of Windows Update, the "update driver" and search HP, Intel, QLogic and other places of Ethernet NIC and Chipset drivers... nothing fits or works.  The hard drive has long been wiped, so there is no recovery partition, nor do I still support discs. :-(

  Is the reported by Device Manager hardware ID: PCI\VEN_14E4 & DEV_164A & SUBSYS_3070103C & REV_02.  164 a same device does not appear on the pci database. :-(

  Yet once again, I need to Win10 - 32-bit (no 64 - bit).  Thanks in advance for any help that can be given.

  Hello:

  There are no W10 driver for this chip ethernet I can find.

  In fact, everything that I could find were drivers for Windows Server 2003 and 2008.

  HP doesn't even have driver Broadcom ethernet on your PC support page, and I couldn't find the site of Broadcom or the other.

  I explored the Broadcom file and there is no support drivers for the hardware ID you have posted in the file.

  So, the only suggestion I can offer would be to try the driver I compressed upwards and attached below.

  Download and uncompress the file in its folder.

  Don't do anything with the files in the folder.

  Go to Device Manager and click on the ethernet controller requiring driver.

  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder, that you unzipped.

  Make sure that the include subfolders is selected and see if the driver will install.

• HP Pavilion Elite HPE 310-t: slave master HD with select cable

  Original HD not was not so I added another WD blue for computer to clone original HD BIOS sees second HD but I can't designate master and slave as cloning said to software.   System doesn't see a second HD.  Here is the SATA HD.  I'm not sure if the PC has cable select function.  Boot HD on end connector and second HD on next connector on the cable. Please notify.  Thank you

  Pretty fun little story about the SATA drives connected to a slick IDE, if you read it correctly.  More fun is the tidbit on "master slave and cable select'.»  I have this rate a red herring, scoring 10 for the op.

• Better graphics for HP Pavilion Elite HPE-570f card

  I have the Pavilion Elite HPE-570f (BV542AA) Windows 7 ultimate with 16 GB of ram upgraded and an upgrade

  HARD drive with 7200 RPM. The P/S is a 460w and ATI Radeon HD 6770 with only 1Gig vram. I would like to upgrade the video card up without compermizing the P/S.

  Does anyone have any ideas.

  Thanx.

  Hello

  The NVIDIA GTX 550TI would be a nice bump in performance.

  The NVIDIA GTX 550 TI compared to the Radeon 6770.

• Help with updates for HP MediaSmart Suite & DVD/BD discs for PC HP Pavilion Elite HPE-112y

  HP Pavilion Elite HPE-112y PC

  VT637AA-ABA

  Genuine Windows 7 Home Premium - 64-bit

  Blu - ray player

  HP MediaSmart Software Suite

  I bought my computer new from Best Buy in 2010.

  HP MediaSmart Version: 3.1.0.1

  HP TouchSmart DVD Version: 4.1.2.5122

  HP TouchSmart Music Version: 4.1.1.4604

  HP MediaSmart Photo Version: 4.1.2.4327

  HP MediaSmart video Version: 4.1.2.4322

  HULU Desktop: Host Version: 0.9.14.1 - SWF Version: 0.9.15.33

  HP MediaSmart/TouchSmart Netflix Version: 1.0.2.0

  I have apalogize, I know that this has been done before, but I'm looking for different software or updates not upgrades.

  A couple of weeks, I tried to watch a movie Blu - ray (made before 2013) through HP MediaSmart DVD, when I put the movie in him would ask if I wanted to check the updates, so I said yes, he started the process of loading and asked again if I wanted to check the updates. Finally, I took the film and went into settings, watched in updates and there was an update. So I chose the update and HP MediaSmart DVD HP TouchSmart DVD changed. After that, the movie played fine.
  
  Now I'm watching a Blu - ray movie (made in 2013) and still once he asks me if I want to check the updates, so I took the film out, went into settings, that update, but there is nothing there. I put the movie back to try again and he asks me if I want to check the updates, so I push No., he would say "disk ready for play. Press Play to start. "So I press start and it will immediately message asking if I want to check the updates. So then the movie is still in I go into the settings, that update, and there is still nothing.

  All DVD for the 2013 game and rain fines. All comics before 2013 play fine. All BDs for 2013 keep asking check updates.

  Now, I find another reason that could not work the BDs is because my DVD/BD players could be updated.

  Device: hp BD O DH4O3S SCSI CdRom Device & hp DVD a DH16AAL SCSI CdRom Device
  Driver provider: Microsoft
  Driver date: 21/06/2006
  Driver version: 6.1.7601.17514
  Digital signer: Microsoft Windows
  
  I clicked on the update for both driver and said that I was aware.

  I find no new updates for HP TouchSmart DVD on CyberLink website. Where can I check updates? In addition, what I have to update all of the HP MediaSmart Software Suite to make it work (and where I do that)? Are there updates for DVD/BD drives and if there is where can I find them?

  Someone, please help me to find the updates.

  Sorry it took so long to get back to that.

  I finally got a new monitor (a long while ago):

  HP Pavilion 22bw IPS monitor 21.5 backlit "

  1920 x 1080

  VGA, DVI - D, HDMI

  So I tried again a movie BD 2013 on the HP MediaSmart/TouchSmart DVD thanks to the new screen and he asked again if I want to check for an update, but it worked fine on PowerDVD from CyberLink 13 (which means I have to buy ). So I have not watched all BD movies on my computer for awhile.

  I recently bought a new computer and restored my old computer to its factory condition and reinstalled all programs and installed the updates I could find.

  After I restored the computer I tried BD 2013 & 2015 on HP MediaSmart/TouchSmart DVD movies and he even asked if I want to check for an update. It's been 2 years and still no new updates! Looks like HP MediaSmart has become obsolete. I don't know if PowerDVD 13 still works because I obviously don't buy it.

  Thus, it seems that if someone wants to play movies BD 2013 or newer that they should ensure that they have the right connection between the monitor and the computer and buy a new BD software to replace the old software obsolete.

  With my new computer, I'll be closing this and boxing upward. So I don't need to worry about this more.

  Thank you for your time and your help. And good luck to anyone else who might have the same problem.

• Pavilion Elite HPE-170 t: problem with the new HP DH16D5S DVD ROM drive

  My office is a HP Pavilion Elite HPE-170 t.  I recently upgraded from Windows 7 to Windows 10.  I have two HP optical dirives, one is a writer, and the other is just a DVD ROM  Both have always worked perfectly with Windows 7.  After you have installed Windows 10 continuous burner work very well works correctly with autoplay.  However, the DVD - ROM, HP DH16D5S, immediately began using autoplay.  Actually the drive was not yet recognized as a drive when you view the drives in the file Explorer.  Finally, it would seem, sometimes taking also longer than 5 minutes or more before doing so and then would work very well.  I tried different types of media, including music CD, DVD video and DVD software with the same results.  I assumed that it was a problem with the drive, maybe a bad capacitor, etc., which was originally not start correctly.  So I ordered a new DH160D5S, but which seems to have been a waste of time and money, because it does exactly the same thing as the original.  I even changed the cables autour between it and the burner, but it made no difference.  The burner still works fine but not DVD ROM.  I tried to find a more recent driver for it, but had no chance.  I found on a Dell website for this drive which was an update of the firmware for Windows Vista and Windows 7, but not for Windows 10.  I advanced and downloaded, but when I tried to run, I got the message: "your system does not meet the minimum requirements for this update.  Update has been canceled. »

  I want to try a different brand of DVD ROM, but would have to buy one without knowing if it would help.

  Any help will be appreciated.

  Since I posted this message I discovered that there is a driver problem with this DVD ROM.  There's no driver available yet to make the drive compatible with Windows 10.  Since then, I returned the drive and replaced by another brand that is compatible with Windows 10.

• New graphics card for HP Pavilion Elite HPE-170 t

  Hi, I'm getting artifacts screen sporadically, Ithink my video card is starting to go bad. I want to get a new one, but I do not know what will fit. My computer HP Pavilion Elite HPE-170 t:

  • Intel Core i7 - 860 quad-core processor [2.8 GHz, 1 MB L2 + 8 MB of cache N3 shared]
  • 8 GB DDR3 1333 MHz SDRAM
  • 1 TB hard drive 7200 RPM SATA 3 Gb/s
  • 1 GB ATI Radeon HD 4850 [2 DVI, HDMI and VGA adapters]
  • LightScribe SuperMulti DVD burner
  • Player 15-in-1 memory cards, 1 USB, 1394, audio
  • No TV Tuner
  • Creative Sound Blaster X - Fi Titanium

  I see by a few other questions here several cards video suggested, but these responses were a few years old and these video cards are no longer available.

  So, any suggestions on the new video cards less than $200, which will be more apt to little and works as easily as possible? Thank you!

  OK, I got my new video card, to be exact of it:

  http://www.Amazon.com/XFX-250E-800MHz-graphics-R7250EZNP4/DP/B00JM5XX9O/ref=dp_ob_title_ce

  http://www.xfxforce.com/en-us/products/AMD-Radeon-R7-series/AMD-Radeon-R7-250E-core-Edition-R7-250E-znp4

  It works like a champ! Took me about 5 minutes to install the card physically and 15 minutes to install all drivers and updates.

  So far so good - everything seems OK, so if anyone is looking for a video card for this configuration, it worked for me.

• Pavilion Elite HPE-170F recovery problem

  I woke up yesterday to a problem of blue screen on my Windows 7 Pavilion Elite HPE-170F.  Following reboot, but would end up the same way.  Tried to boot mode without failure, but same result.  A technician came to the House and he did Diagnostics with its test disc that says the HD had to be replaced.  I had my recovery disks that I made when I bought the computer 4 years, which made her happy.  He installed the new HD and put the old in another location, planning to transfer my files after the restore.  He began the process of recovery with disk 1 and told me to change the disks as needed while he went to see another client.  All done and then it entered into startup mode of windows. went black for a while and then gave me the message "Windows Setup could not configure Windows to run on hardware.  The technician returned and tried other things but the same results.  We ordered a new series of HP recovery disks but will take a week.  The question, since the instructions say to disconnect everything except the monitor, keyboard, and mouse, would be the printer that is wireless a problem and should it be turned off?  Also, the mouse and the keyboard are different than the original, which would be a problem.  In addition, Windows installed several updates of the day before the problem.

  I venture a guess the your computer uses an Intel chipset, can be set to "RAID", and the replacement of the hard disk is a disk AF (Advanced Format). Please see desktop HP - can not recover the PC after replacing the Hard Drive with an AF Drive (Windows 7 and Vista) for more information on this topic. Please see computers HP-HP System Recovery troubleshooting (Windows 7) for more information on the AF drives and some troubleshooting tips.

  Alternatively, if you can still read the Windows product key of 25 characters on the COA Microsoft attached to your computer, you can install Windows 7 using this key. Please see "how to install Windows 7 without the disc" to get instructions on how to download Windows 7, create the installation media and install Windows 7 using the product key 25 character of the COA Microsoft on your computer. Using this method will not install HP customizations or value-added software and you will have to manually install all necessary drivers.

  Windows 7 SP1 can be found HERE and HERE.

   

  Direct link to Windows 7 USB/DVD Download tool.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• HP Pavilion Elite HPE - 480t computer and burner blu - ray 12 x HP bd 340i

  Model bd340i in the middle of last year, I bought HP 12 x Blu - Ray burner. When I bought my HP Office in December 2010 model HP Pavilion Elite HPE - 480 t, I installed the burner and everything worked very well. Today, I tried to burn a blu - ray disc, and he returned with can't read media, which stood on imgBurn. So I tried the same thing on the burner systems, and she came back as no drive in the status bar. I have also tried burning CyberLink software and the same thing no disc.

  I then tried to play the two store bought and home made blu - ray disc and could not read media. I was ready to blame it on a bad burner but then I tried a regular DVD the two store bought and done House, and it plays very well. I then tried to burn a single dvd double layer with all the burning software three I have and it is still fine, no problem. It's just the blu - ray media that cannot be read or written. The only supports blu - ray, I used from the first day was Kodak and never had a problem. That's what baffles me.

  At this point, I don't know if it's a hardware or software problem with the computer or burner blu - ray or both. 3 different burning programs works fine on DVD but not blu - ray, DVD plays fine but can't play or burn blu - ray discs.

  Could this laser blu - ray crapped out and the dvd reading and writing laser still works?  Must a blu ray burner still lasers for both media (DVD and Blu Ray)?

  Everything else with the computer works fine. I even tried uninstalling and reinstalling and it is the same, I tried to update the drivers and firmware on your site and still does not work. Please help.

  When did you purchase your product? : December2010
  Product HP Pavilion Elite HPE - 480t CTO desktop PC
  Select a problem area: other
  What is your serial number (SN): [personal information deleted]
  What is your operating system? : Microsoft Windows 7 Home Premium 64
  Your computer is unable to work with Accessories products? Please select all the boxes. other
  What type and brand of CD/DVD media you are using? Kodak 25gig of Bu-Ray and dvd HP
  The CD/DVD writer burner was built in the computer when you bought it? NO.
  You hear the sound from the speakers connected?
  The display on the product seems to work correctly? Yes
  Have you connected the product to your TV, DVD player or a music system? NO.

  If there is an error message, please specify: cannot read media
  Description of the problem: I bought burner HP 12 Blu - Ray model bd340i in the middle of last year. When I bought my HP Office in December 2010 model HP pavilion Elite HPE - 480 t, I installed the burner and everything worked very well. Today, I tried to burn a blu - ray disc, and he returned with can't read media, which stood on imgBurn. So I tried the same thing on the burner systems, and she came back as no drive in the status bar. I have also tried burning CyberLink software and the same thing no disc. I then tried to play the two store bought and home made blu - ray disc and could not read media. I was ready to blame it on a bad burner but then I tried a regular DVD the two store bought and done House, and it plays very well. I then tried to burn a single dvd double layer with all the burning software three I have and it is still fine, no problem. It's just the blu - ray media that cannot be read or written. The only supports blu - ray, I used from the first day was Kodak and never had a problem. That's what baffles me.
  Please provide previous steps of troubleshooting, or information that can help HP help you. : I don't know at this point if it's a hardware or software problem with the computer or burner blu - ray or both. 3 different burning programs works fine on the DVD but not blu - ray, DVD plays very well, but can not play blu - ray.
  Nothing changed since the device was working properly (installation of SW, settings, wiring, etc.): everything with the computer works fine. I even tried uninstalling and reinstalling and it is the same, I tried to update the drivers and firmware on your site and still does not work. Please help.
  How would you describe your level of technical skill? : intermediate
  First name Peter
  Name, first name rider
  [Personal information]

  Arcticwolf, sorry, I miss read your post details. That strangely resembles a failed drive. Try unistalling and reinstalling the drive, including the software and driver. If a problem has occurred, it may fix.

• Upgrading the PSU and GPU for my HP Pavilion Elite HPE-510 t

  Operaring system: Windows 7 64-bit

  CPU: Core i5-2500, 3.3 GHz

  Memory: 10 GB

  Video graphics card: GeForce GT 420 - OEM

  Hard drive: 1 TB

  Computer case: height: 38 cm (14.96 inches), width: 17 cm (6.69 inches), length: 41 cm (16,14 inches)

  Power supply: power supply 300W

  Several features of the product: HP Pavilion Elite HPE-510 t

  due to the diablo 3. I updated graphic setting the lowest. FPS is between 15-22 so I'm interested in upgrading my power supply HP Pavilion Elite HPE - 510 t(specs are above) and graphics card with the following, respectively:

  GPU: ASUS GeForce GTX 560 (Fermi) 1 GB 256-bit GDDR5

  GPU size: 9 "x 4.4"

  Power supply: Antec High Current Gamer HCG-750 750W Series

  "Power supply Dimensions: 7.1"x 5.9"x 3.4"

  I wonder if these prodcuts will enter the computer, as is or if I should look for other products.

  Thank you

  The ASUS GTX 560 should adapt and work very well. The Antec PSU is great and very likely to have problems in the space provided. It can interfere with connections to the motherboard and push against the CD/DVD discs. Please look at the Corsair CX600 instead. It is only slightly larger than the block of power SUPPLY HP stock and is known to adapt.

  Frank

• Replace the HARD drive in the new Pavilion Elite HPE-180 t.

  I'm not a professional computer, but after 30 years of use, the upgrade and repair PC home and the office, I'm embarrassed to post this thread - but here goes.  I took delivery of a few days ago the new highest indicated HP computer model in the topic of this thread.  The new computer is beautiful and everything worked perfectly from the start.  I decided after a few days to check, everything was fine and proceeded to a few pieces of hardware to transfer from my old Dell (a fairly new 1 t WD SATA HDD on which coied got a lot of data from the former count and a new BD/DVD ROM SATA optical drive).  Everything was fine once I figured out how to get these two drives in the enclosure waterproof on the new computer, but all reconnecting the SATA cable on the main came with the computer HARD disk, I broke up some pins on the HARD drive that made it of course useless SATA port.  I of course take full responsibility and do not wish to get involved with HP technical support to replace the disc - and frankly, I prefer not to put another HDD Seagate support because I prefer a 1 t Cavier Black SATA WD which I believe is one of the most reliable RESEARCH on the market right now, and I can buy it for around $200 instead of the $400 I uknderstand fresh HP for the same size of Seagate replacement.

  Here's my question, can I just buy a new HDD WD and install it with my own final Win 7 x 64 without the HP recovery disks (they did not come with the new computer, and I had not yet created my own recovery disc).  Frankly I'd rather have a completely clean install of my Win 7 OS without the HP partition and other HP software on the HARD disk.  Is this possible or HP has some sort of identity with their software which must correspond with the BIOS or something like this?  REALLY, I don't want to return the computer to HP to get called into service because I just started a small business that involves a lot of video editing and I can't be without the computer for weeks, while HP is concerned with him (I've read the horror stories about the high cost of the repairs and the long repair time but I do not wish to keep my warranty if possible).

  HP Pavilion Elite HPE-180 t; 2.8 Ghz quad-core Intel i7 CPU; Intel x 58 chip; Win 7 64 bit ultimate OS. 12 G RAM;
  1.8 NVIDIA GeForce GTX-260 G graphics card; HP w2338h HD widescreen LCD monitor

  I have the same PC, only the model number has been changed.  Yes, you can use your own license W7 and install it on another drive or a replacement drive.  You can get the drivers from the HP site web support HPE-180 tfor your PC or other sources.

  Some software manufacturers third HP is very useful, so you might want to consider ordering the HP recovery discs and make a full recovery to factory.

• How to add to my HP Pavilion Elite HPE-590uk Usb 3.0

  Hi does anyone know if I can improve my HP Pavilion Elite HPE-590uk for usb 3.0 and if so could you recommend a product that I could buy to do this.  Thanks in advance.

  One of them check it:

  http://www.overclockers.co.UK/showproduct.php?ProdID=CC-003-AK

  This is to use a pci-e x 1 card. You have 2 these slots available. This will show you how do:

  http://h10032.www1.HP.com/CTG/manual/c02255267.PDF

  See the section on the replacement of a card.

  Instead of plugging on the long black slot which is a video card plug into one of the slots black short. You have Windows 7 I think which means that you will need a driver, but that should come on a CD with the card. Will need you a power connector (molex) on the map, too.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.