HP Pavilion G6 - 2148TX Power Up after replacing the fan problem

Similar Questions

• My HP Pavilion DV6 will not start after replacing the screen

  I just replaced a cracked screen by following the instructions in the maintenance manual and now it does not start. The power light turns on and the fan works but nothing else happens. What can I do to trouble shoot this problem?

  The most common problem is the connection of the cable to the screen.  Make sure that it is tight. Check the connection to the motherboard as well, but it's usually OK.

• T61 suddenly stops after replacing the fan

  I was getting a fan error (which prevented the start unit), so I ordered a replacement.

  On install last night, everything seemed fine. Unit ran fine for 20 m and then Bam! abrupt stop.

  This morning, same thing, the two witht the battery installed and with it out.

  I have to suspect the fan, but I guess that the unit would not start even though the fan was not working.

  any suggestions to diagnose the problem?

  Thank you very much

  Peter

  Hard to say...

  The theory says the system automatically stops to avoid damage permanent, but if you tried to run more than once...

  In any case a new CPU won't cost you much. Try again once the thermal paste is reapllied.

  I hope you're using the HMM and following the procedures described here. Don't forget to tell us the number of type of machine (see my post above)

  Good luck!

• I have to reset the charge cycle counter after replacing the battery?

  I had a defective power adapter, running on the number of cycles of load on my battery.  Thus, it no longer accepts a charge.  I have been running only on AC for over a year now, but finally decided to replace the battery.  What are the steps to reset the counter after replacing the battery?

  Replce just the battery, the battery will communicate the number of cycles to the computer. No adjustment is necessary.

• HP a1250n, radeon xpress 200 question after replacing the CPU, Standard VGA Graphics goes not down

  Recently, I messed up my CPU and bought a replacement (exact same kind). I am running windows 7 ultimate and for about 6 months prerequisites with no problems. After replacing the CPU I get intermittent lock ups, sometimes with a small portion of the screen flashes. I say intermittent but at least every 15-20 minutes. Different programs, different habits, but still the screen freezes.

  I went in and deleted the driver under graphics cards, pick a 'completely remove the option' - it after restarting the system on its own charged for a Standard VGA Graphics Adapter and since there is then no more accidents. Of course the functionality is not as complete, large icons and such, but it works.

  If it certainly seems to point to a driver conflict I think. But for this machine, is there ever any single Vista Windows 7 driver. My skills are not so, but I'm moving.

  Any guidance?

  Hello

  Yes, your PC has integrated graphics controller: ATI Radeon XPress 200, we don't find drivers compatible Windows 7 ATI.

  The BEST OPTION: Buy a video card, then insert it into slot PCI Express 16 on the motherboard to better display and multimedia performance with Windows 7 to a value using else, it looks just like Windows XP

• Model: G6-1D98DX, refurbished: renovated pavilion laptop g6, replace the fan with what?

  When I powered my laptop Pavilion G6 refurbished, it gives a disturbing message on the fan turns not and the processor of cooking and automacially stops in 15 seconds. OK, replace the fan.

  By the? appropriate? HP 'Maintenance and Service of Guide' (Doc PN 649111-002), I took part BUT Guide HP, the processor heat sink is held by 7 screws... only it renovated its heatsink is a model of 4 screws, and the motherboard was ever available for 7 screws.
  How to order the appropriate and/or fan-with-heat sink fan? the fan-with-heat sink seems to be a unit

  use data created on the fan or radiator Assembly to try to find a part on google or ebay.

  http://www.eBay.com/ITM/new-OEM-HP-Pavilion-G6-G6-1000-series-cooling-fan-with-heatsink-641024-001-4-pin-/251637960612?hash=item3a96ca8fa4:g:dTsAAOSwq5lTmneN

• High temperature after replacing the CPU T2500-> T7200 at T60

  After replacing the T2500 CPU temperature CPU T7200 varies from 70 to 85. It seems high, I think about the replacement of the thermal grease or thermal paste application. What could be better? To finish with the original grey Ribbon and fix a new radiator or better coat of toothpaste?

  orion9727 wrote:
  There was a test done and toothpaste is out near dough more themal.
  Artic 5 should never be used in a laptop.
  He money and this is a no no on mobile cpu.
  Use a no driver or a thermal buffer.

  the gray Ribbon is a preferable themal pad use this WHICH CAME into IT.
  Because maybe a wedge and to finish with this and without contact.

  you upgraded from a 31 to 34 watt TDP watt not much, but he's going to run hot.
  75-80 c is hot Yes, but you have class 65nm cpu will run hot because it is old and a lot of work.
  If you all know toothpaste can served in the tests but I have not use because it can dry out and not sure what exacly.
  heat wise, I do belive in toothpaste is wise very good heat but stick with the gray Ribbon.

  Please do not take into account the (re) post above.

  I used AS5 on thousands of ThinkPads with no ill effects, in fact the opposite. Research experiences minimal posted by other owners on Bill Morrow ThinkPad Forum will confirm this statement as well. Arctic Silver is as good as it gets unless you want to spend $50 for a tube of thermal paste.

  To OP, your machine is running too hot for the processor in question. My 15 "T60p with T7600 is inactive at least 50 degrees C and does no more than 62 in normal use. And Yes, it was AS5 inside.

• My printer HP LaserJet 1536dnf printer prints black pages after replacing the toner with a new one!

  I changed the toner cartridge for my printer HP LaserJet 1536dnf with a genuine HP toner cartridge and now it's printing the pages in black.  Any suggestions on how to fix this?

  Thank you!

  Hi @Beaglemom49779,.

  I see by your post that you have replaced the toner and now get all black pages. I can help you with this.

  Have you had the same problem with the printer before replacing the toner?

  It could be a hardware or with the printer fuser problem.

  If the problem started just after replacing the toner then most likely, the toner.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector)

  Number one cause of problems with toner.

  Check if the drum unit for damage:

  1. remove the cartridge of toner product and check that the tape has been removed.
  2. check the memory chip for damage.
  3 examine the surface of the imaging drum on the bottom of the toner cartridge.
  CAUTION: Do not touch the roller (Imaging drum) on the bottom of the cartridge.

  His fingerprints on the imaging drum can cause print quality problems.
  4. If you see the scratches, fingerprints, black on the drum, or any other damage on the imaging drum, replace toner.
  5. If the imaging drum does not appear to be damaged, rock the toner cartridge gently several times and reinstall it. Print a few pages to see if the problem is resolved.

  Please call our technical support if the there is a problem with the toner and you learn about a replacement, to the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. Contact HP.

  Good day!
  Thank you.

• System Restore to factory settings after replacing the hard drive?

  I have a Lenovo ThinkCentre A52, which recently required a change of hard disk and the removal of a defective RAM 1 GB stick. When I bought my computer, it came with Windows XP Pro and the new hard drive that the updated computer has Windows XP Pro, but it seems to be missing a large part of the software (drivers and programs) that originally came with the computer, and even if I downloaded and installed most of them since the Lenovo Web site There are still some problems related to software that I can't fix. Ideally, I'd like to go back just to restore the system to the factory settings using the ThinkVantage Rescue and Recovery program, but I don't know if it will work. All programs and the necessary drivers will be installed again, even if my current hard drive is not 'knows' thereon? I need to get a Windows XP Pro installation CD, if I want to keep my operating system? Also, is it important that my current hard drive is half the previous, or that I now have half as much RAM?

  Thank you

  After replacing the hard drive, the only way to restore it to the State of the plant is using the Lenovo installation diskettes. You can also ask if Lenovo has a solution to your problem without having to reinstall Windows.

  You can download Lenovo drivers if they are not included on the installation disk. The size of your hard drive does not matter.

  Lenovo - call to order recovery disks:
  http://support.Lenovo.com/en_US/product-and-parts/detail.page?&LegacyDocID=YaST-3P2QYL

• my hp 5550 printer is not printing from a connection direct mac after replacing the drive hard * bleep * cause of

  my hp 5550 printer is not printing from a connection direct mac after replacing the hard drive due to the recent recall

  So, you have reinstalled the HP software after replacing the hard drive?

  What version of Mac OS X are you using?

• Windows will not start after replacing the motherboard

  To begin, I must say that I am pretty clueless when it comes to computer skills.

  To summarize, I sent my CPU to a repair shop when my computer has stopped working. I removed my hard drive before starting the repairs because it contains confidential data.  They have narrowed the cause to a faulty motherboard and replaced by a new dissimilar.
  At the store, the guy had a vista 64 bit recovery disc so I have it home and tried to fix it. He said it will be a breeze and relatively bug free. As part of the Startup Repair, I tried to drive the Startup Repair, and tests were all successful except one. An error of diagnosis readings

  "Unspecified system configuration changes may have caused the problem.

  Repair action: repair and checking the integrity of system files

  Result: failed. Error code 0 x 490

  time taken = 720023 ms

  Everything I've done has led to a brief blue screen to the Windows loading screen and then it restarts itself.

  I also tried to restore to the previous two points, but it has also led to the square - a brief blue screen after the loading screen and restarts on its own windows. I'm not ready to reinstall vista and I can't afford to do it too, because I don't have enough disk space to perform another installation. Nor am I willing to reformat one of my two disks.

  If you need additional information on the specifications of the material that must be provided, ask me.

  IM at my end intelligence now, and I really hope to solve this problem.
  Thank you.
  Bryan M

  Hello

  I'm sorry, but you have to completely reinstall the operating system after replacing the motherboard with a different motherboard.

  "Startup Repair" is exactly that: a start NOT a repair system repairs

  What has happened, it is the operating system on your hard disk contains the drivers for the old motherboard and does not and you can't change drivers in doing what you do.

  The only way to solve this problem is to reinstall Vista.

  You wipe the hard drive and restart and make sure that the repair shop gave you the disc to install the new drivers of motherboard after you reinstall vista or download on the website of the manufacturer of the motherboard.

  And here a question for you to consider, too.

  If you bought a copy of Vista retail yourself, you can use the method above to a new installation and then install the new disk motherboard drivers.

  But, if your computer is a trademark of purchased manufacturer, HP, Toshiba, etc., you can not change the motherboard that the license of Vista OEM is stuck at motherboard the origin of the manufacturer that it has been installed on and now you canceled your Vista license.

  See you soon.

• Replacing the fan Pavilion dv6

  Hello! I found the manual for my computer but I am not sure how deturmine if he has a discrete or UMA memory in order to order the part to replace the fan.

  The fan in the summer in place for some time, leading to overheating of the issues and has now finally stopped working altogether

  I'm on a Pavilion dv6-6140us, running win 7

  Hi TheDragonGirl,

  Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I saw your post about if your model is discrete or UMA memory. Pavilion dv6-6140us specifications , it has AMD Radeon HD 6620 G Discrete-Class graphics card.

  Thank you

• How can I reinstall windows 7 after replacing the hard drive?

  How can I reinstall windows 7 after replacing the hard drive? do I have to call microsoft or I can retrieve it somehow to the old hard drive?

  Well, that certainly puts a different point of view on this subject.

  There are data recovery services that can recover data from disks that have suffered from various types of failures. However, they are quite expensive. Unless the data is particularly useful, it is generally not useful.

  If your Windows 7 is an OEM version, installed on the computer when you bought it, the manufacturer could have a recovery disk on sale. If it was a retail copy and you always have the appropriate product/serial number, you can get a DVD of their team of parts replacement.

  http://support.Microsoft.com/kb/326246

  Tom Ferguson

• Cannot access through desktop remote after replacing the hard drive

  After replacing the hard drive, I can't access the computer via desktop remotely.  running Windows 7.  Settings of remote desktop access.  The firewall is disabled.

  Hello

  I appreciate the efforts that you put to publish the query on this forum.

  I suggest that you post the application on Microsoft TechNet forum because we have experts working on these issues. You can check the link to post the same query on TechNet:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Please do not hesitate to contact us if you have other questions related to Windows.

• Install the operating system after replacing the corrupted hard drive Asus q500a

  The hard drive on my Asus Q500a is bad (he had checked the repairman). They told me that I could replace it (it will just keep failing until at last it dies just) but I have to re - install the operating system. The laptop comes with Windows 7 and I upgraded to 8 when it came out (I think). I don't have a recovery disk.

  How can I replace the corrupted hard drive and re-install the operating system?

  If I need to buy Windows 8, where can I find?

  Would it not easier that I left the repair shop handle it?

  Thank you in advance.

  Hi Kristi,

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand that the problem with you want to reinstall the operating system after replacing the hard drive corrupted on the system.

  Certainly, I understand your concern and will try my best to help you.

  I suggest you check the suggestions contained in the Microsoft link below and check if this is useful.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/replacing-hard-drive-and-re-installing-Windows-8/e8dbfc81-5294-4c94-9276-0f36e0a66e59

  In addition, you can see the suggestions in the link given below.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/reinstall-Windows-8-after-the-operating-sytem-has/30d47e63-296b-4466-ae9d-4628084541dc

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

  Jayant