HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

(1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

(2) I tried to change the power adapter too.

The problem is that it is.

Your advice is very much appreciated.

Thank you best regards &,.

Zia

Dear customer,

Welcome and thanks for posting your question on the Forum of Support HP

It seems that you are not able to turn on the laptop and tried to solve the problem

Please perform steps listed to find out if it is a hardware or software problem below:

1. remove all cables and devices, disconnect them and try to turn on the device

2. check the LED light situation and ensure the action of the spring button / stop is normal

3 Exchange with a well known power cord and the AC adapter

4 Pack no adapters are available, check if the power adaptor is slightly warm

Note: This will give us an indication that the power adapter could be good

5. do you know if the laptop was in battery or power adapter when you used the last time

Note: Make sure that there is no spill of liquid or cutting

6. check if the Port of the AC adaptor is loose/broken

Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

Hope this helps for other queries to answer the post and feel free to join us again

* Click on the star of CONGRATULATIONS on the left to say thank you *.

Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

Thank you

K N R K

I work on behalf of HP

Tags: Notebooks

Similar Questions

  • Pavilion dv6: laptop does not charge when it is plugged

    Today my laptop stopped load so it was still plugged in, ive tried turning on with and without so that connected battery and still nothing is my battery or power cord my problem? The cord connected to the ac area seems loose also, but except that there's no damage.

    Ok. To solve your problem.

    The power\charge the light come on when the adapter is plugged in and the battery is removed?

    Shake gently the connector to the laptop or the power connector from the power adapter does the led flicker?

    The led charge\power is a diagnosis which lets you know if the power adapter is working or has failed.

    If the led does not illuminate the resolution of the problems that I have described is performed, then the power adapter has failed and must be replaced.

  • Pavilion 15 laptop: HP Pavilion 15 computer PC2170 laptop does not boot to Windows - 2 years

    Hi, my Hp Pavilion is only 2 years and 2 months (not very old at all) but suddenly it does not start in Windows, it hangs at the HP logo screen, it starts with an HP logo screen then goes to another screen of the HP logo, and then freezes. I can't get into safe mode.  I got in the Hp diagnostic screens and I conducted tests on all and everything.

    I did a hard reset, still frozen.

    I removed the cover, he went out and placed him in, still nothing.

    Whenever I have to try and reset it, he said administrative privileges is necessary, but there is no administrative privileges on this computer.

    There is no restore point.

    I ran chkdsk via the command prompt and had no error.

    I tried running sfc: scannow but I had which was something in the meantime and could not do.

    The laptop is: laptop HP Pavilion 15 2170

    A6-5200 APU AMD processor

    Can someone computer whizz out there enlighten us on this you problem, please.

    When you request support, please provide the model name and product number complete (p/n) of the HP computer in question. HP/Compaq made thousands of computer models. Without this information, it can be difficult, even impossible to help you solve your problem.

    The information requested above are on the bottom of your computer, inside the battery compartment or on the BIOS boot screen. Please see How can I find my model number or product number? for help more to find this information. DO NOT include your serial number.

    If you have any other questions, feel free to ask.

    Please click the 'Thumbs Up' white LAURELS to show your appreciation

  • Dell Precision M6500: Reference DELL M6 500 computer laptop does not charge when the work and no start-up when which

    Laptop DELL M6 500, do not load when the work and no start-up when which

    just bettry lights blink when phone on Exchange when I plug laptop tap, on bettry

  • Laptop does not charger and cannot get into the Bios, help!

    Hi, I own an Acer Aspire 6935 G, so far he treated me so. Recently, the charger port broken (one of the wires came loose). I have brought a replacement and mounted in it, but on my charger fuse blew!

    Then I took another replacement just to the case where there has been previous replacement I bought and nothing major, new replacement seems to work well (lighs load lights up) but it does not all power in the laptop. Witnesses of load lights as indicated, but the laptop won't before the Acer splash screen. Due to the battery being dead, I can't access bios set up so I can check the status of my laptop not enter recovery. I was wondering if it could be something other than a hardware problem, and if this is the case; It is expensive to do is fixed or am I better off buying a new laptop?

    Thanks in advance!

    This is a:

    Acer Aspire

    6935G

    Intel Core DuoT6400

    4 GB OF RAM

    Windows 7 Ultimate

    Edit: There is think beep when the chargers plugged into the lapto, if that makes a difference?

    Lugman > recently, the charger port broken (one of the wires came loose). I have brought a replacement and mounted in it, but blew the fuse on my charger! >>>

    Sorry, but it does look like a hardware problem. Sounds like the power supply may be about to blow another fuse. I think you have a short or large scale electric leakage somewhere that prevents charging of the battery and power - it but maybe not enough (yet) to blow another fuse or switch off the LEDs.

    First remove the battery and power connections before you tear things. The first place I would look is around the port of loading where your problems started and hope that it's not deeper in the system where it can cause some MB or more serious damage. Look for the places where the lines of welding on the System Board may be in contact with a screw or a metal on the ground. While you're there, reconnect both ends of all accessible Ribbon (like the video and keyboard) connectors. Also to the HARD drive, modules of memory vivid and all the other connectors for component for good measure.

    Once you have checked everything, and before you have wound all caches and screws, see if you can carefully insert the battery into the receptacle and plug the charger. Don't try to power. You can do this on an insulating surface to avoid the land of naked drivers. The LED light looks like he is in charge? If so, let it continue to charge without trying to power on. I think after 4-5 hours, the led that would indicate a fully charged battery. If so, I would try and then power on. If not, and it's still seems to be in charge, stop, do not try to and we will draw the next steps.

    Jack E/NJ

  • computer Vista laptop does not stop when the lid is closed

    I have all the correct power settings. mode when the lid is closed, I tried setting Hibernate and sleep. It just keeps running and running, I'm afraid it will overheat. but it should stop when the lid is closed, correct? Thank you sissy

    Hello banditpunpun2,

    Thanks for the return of the response.  I also go to your manufactures website and confirm you are updated with the lates drivers, updates the firmware and BIOS.  I even watch the forums on the manufacturer's Web site to see if others have experinced the same question.

    Please let us know status.

  • My laptop does not work on battery even though the indicator said there are 90% of the available power

    original title: laptop BATTERY

    My laptop does not work on battery even though the indicator said there is a 90% power disponiblesLorsque it is plugged in and charging. The battery would be dead even if she says she can still exist?

    Hello

    Check with support from the manufacturer of their books online and the drivers and their forums system
    (as applicable) for known issues. Some manufacturer issued BIOS and other updates to help the battery
    problems.

    Control Panel control - plan change Options - power plans - power - advanced settings
    Parameters for the drainage and the use of parameters (this is how much to use and not how much or how)
    long to load).

    In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
    systems overload are not a problem.

    Here are some tips to help and troubleshoot battery issues.

    Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
    eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
    them and be careful). Batteries are old, or it could be a problem with the computer.
    Check with the support of the machine system, and many of them have on line forums.

    New Lithium-Ion type battery usually last longer if you do not unload then less than 30%
    However on a laptop that not extend their life a lot. Best is to use the a/c adapter
    When this is possible.

    I use the free version of BatteryBar to monitor my battery. Click on the green button on the
    Yellow box on the right side of the page to download the latest stable version.

    BatteryBar - free version available
    http://osirisdevelopment.com/BatteryBar/index.html

    Another good program

    Vista battery saver - free
    http://www.codeplex.com/vistabattery

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    You can also check with the manufacturer of system and forums that many use their own
    proprietary software to monitor the battery and they could be known problems with your battery.

    ============================================================

    Try this - to make a Restore Point

    How to create a Vista System Restore Point
    http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
    Update the drivers (which can do nothing) - then do a right click and UNINSTALL each.
    RESTART which will update the driver stacks.

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    I hope this helps.

  • I'm trying to install Adobe PS CS3 for my boss on another computer. I put the program on a hard disk and copied to the other computer now, it does not open and said he needs the license. What can I do to make it work on this computer?

    I'm trying to install Adobe PS CS3 for my boss on another computer. I put the program on a hard disk and copied to the other computer now, it does not open and said he needs the license. What can I do to make it work on this computer?

    Copy the program through a new machine will not work.   Install it using installation files and activate using the serial number assigned to the license.

    CS3 - http://helpx.adobe.com/creative-suite/kb/cs3-product-downloads.html

  • My DVD player does not open when I click on the button

    Hello

    I hope someone can help me.
    My DVD player does not open when I click on the button.

    I tried clicking on eject on the DVD drive icon in my computer and it comes up with an error message.
    I think I deleted the cookies the other day. Who would have something to do with the problem?

    Any help would be greatly appreciated that I really don't want to send my phone to a technician.

    Hello

    Try to manually open the CD/DVD drive.
    Near the eject button, you will find a small hole.

    You can use a small object like staple and could push gently into this hole.

    Usually, this should help to open the drive manually.

  • the Task Manager does not appear when right-clicking on the taskbar

    The Task Manager does not appear when right-clicking on the taskbar

    Hello

    It appears when you press ctrl + shift + ESC? It seemed before? You are an administrator on this computer or is it a corporate system?

    If he has suddenly ceased to be available, it's a good sign that you have picked up a virus or some kind of malware. Formal analysis in safe mode is your first line of defense.

    Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

  • My wireless router does not appear when I shoot to the top of my devices. It shows my fax, modem, scanner and a few others. But not my belkin wireless.

    My wireless router does not appear when I shoot to the top of my devices. It shows my fax, modem, scanner and a few others. But not my belkin wireless. And when I try to add it, the system can't find it. Please help

    Belkin support for your model, for installation instructions.

    Your router will not appear in the devices

  • I have photoshop cc 2015. For the last 2 days it does not open when I double click the icon. What should I do?

    I have photoshop cc 2015. For the last 2 days it does not open when I double-click the icon. What can I do to fix this?

    OK completely reboot Windows 7. When he started to look in the Task Manager under process for photoshop.exe it shouldn't be there. If it is highlighted and press the button end process. Now right-click the Photoshop icon and select run as administrator. Photoshop starts, you should see photoshop.exe in the list of running processes. When you close Photoshop it should disappear from the list.

  • I have problems with the shopify widget in Muse. I have configured my shopify store, but when I placed the button 'buy' is didn't tell the product no availabe longer and does not appear when I'm writing the site.

    I have problems with the shopify widget in Muse. I have configured my shopify store, but when I placed the button 'buy' is didn't tell the product no availabe longer and does not appear when I'm writing the site.

    Please contact the original publisher of the widget.

    Thank you

    Sanjit

  • Compaq CQ58 computer 301SA laptop does not connect to 50Ghz band on router

    My laptop does not connect to the band 50Ghz on my router dual-band. I know that my router Netgear dual band diffuse 24 and 50 Ghz, but the laptop only shows the 24 Ghz band depending on availability.

    I have a Compaq CQ58 301SA Notebook PC, Windows 8 (64 bit OS).  It has a Ralink RT5390R 802 11bgn network adapter and a Realtek ethernet network adapter. I use the laptop wireless, for example using the Ralink connection and it connects easily to the 24 GHz band, but I want to broadcast TV programs and movies smoothly, for which, I understand that the 50Ghz band is preferable. I pay my ISP (Virgin Media) for a connection to Super-fast broadband but my laptop seems to be limited to the 24 GHz band. Seems to be the case if I work with the adapter Ralink wireless or wired with Realtek ethernet connection.

    This problem can be corrected? If so, how? What I have done research on the web, the problem seems to be network adapters. Can they work on the 50Ghz band? Or do I need to download another adapter (if so, which?) Or use an adapter external network I plug into a USB port?

    Driving me crazy...

    Hello:

    The Ralink RT5390R 802 11bgn is a map of the only band (2.4 GHz) only.

    Whenever you see a labeled bgn wireless card, it is a single band card.

    Cards labeled dual band abgn or agn.

    The maintenance manual (Chapter 3, page 19) does not indicate that any internal dual band card is supported, so you would probably have to go with an external usb dual wireless adapter.

    http://h10032.www1.HP.com/CTG/manual/c03593268.PDF

  • Computer HP laptop, does not accept the recovery disks and don't accpet Windows Vista upgrade (HomeP to ultimate).

    Apparently the upgrade does not recognize that Windows is on the drive, but cannot restore the original software as HP blocked their recovery disk. The recovery partition is there, but he cannot get starter.  The recovery disks have the original spirit operating system Windows - how can I get the upgrade to recognize?

    Hello

    an upgrade must be done from vista, NOT operating system by booting from the disk to upgrade

    as you have problems using the maunfacturers recovery process, upgrade disc etc., read what you may have hardware problems.

    If you have problems with the process of recovery of manufacturers, contact the manufacturer

    It's their recovery process not microsofts

Maybe you are looking for