HP Pavilion HPE h8-1050z-switch series

Similar Questions

• Pavilion HPE h8 - 1360T: Max RAM per slot (4 locations)

  I'm upgrading RAM on my 1-1/2 year old h8 - 1360t.

  On the page "Product Specifications and configurable Options" (http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03425388 & DocLang = in & docLocale = en_US & jumpid =... , under Hardware Options - memory, it says "must select one of the following options:...") 16 GB (4 x 4 GB) PC3-12800 DDR3 (PC3-10600 on this system turns)' (the only 16 GB option - maxed out for WIN7 64 bit).

  In addition, in the support page "HP Desktop PCs - the upgrade memory (RAM)" (generic - non-specific to any model) (http://support.hp.com/us-en/product/HP-Pavilion-HPE-h8-Desktop-PC-series/5258496/model/5261720/docum, under "Verification of the quantity of memory can be added to your computer model", it says "to find the amount of memory per slot, divide the maximum amount of memory that the computer can hold by the number of memory locations of the motherboard. Usually, this is the maximum amount for each type of memory. For example, if the computer is able to contain a maximum of 4096 MB (4 GB) memory and the motherboard has four memory slots, install 1 GB (or less) per slot. »

  When I check the options of 'Memory' on www.crucial .com, the only 16 GB option it gives is 8GBx2.  Can I do trust what is Crucial says about it (which seems to contradict what the HP options & specifications page)?  I think that the answer is Yes - that HP doesn't care. and options page is just saying how it would come if I had ordered with maxed out at 16 GB RAM - but thought I would ask before ordering memory.

  Thank you for responding to this.

  I dug a little further on the Crucial site, and it seems that the 8GBx2 actually works:

  Recommended for my computer:

  

  And here's the review of one of the examiners:

  

  The reason, I was a little skeptical about what the HP standard sheet said for the computer I had before this one, HP said a certain maximum size of RAM (below what the operating system should be able to manage).  There was a post on the HP forums who said you could use the larger RAM size (until the operating system can manage) in this model computer.  I tried and it worked fine.

• Pavilion HPE series, LP028AV # a: Windows has not started, but ended up with Recovery Manager without control

  When I started my desktop computer, Windows did not come to the top, and then he came to the Recovery Manager window. So, I wanted to select System Recovery, but the wired keyboard seemed to be locked and so was the wired mouse.  No selection is possible on the window. Please help me to unlock the keyboard in order to proceed to the recovery of the system or to correct the problem.  I also tried to restore the system from the recovery disks, but the keyboard and mouse have been locked as he came to the Recovery Manager window. Here it is a little recap of my office-info:

  Product name: Pavilion HPE series

  Product number: LP028AV #ABA

  Model number: h8 - 1070t

  Thank you for your help in advance.

  Jay

  Hello.

  After replacing the batery, I got a black screen. But I discovered that the cable from the monitor was not completely connected after that I moved the PC and the monitor. Once I fixed and restarted the PC, keyboard and mouse are animated.  I'm currently running System Recovery.

  Thank you for your excellent support as well as your patience.

  Jay

• HP Pavilion HPE 1090 t: could someone help me please... Desktop HP Pavilion HPE h8-1090 t CTO - PSU replacement/compatibiliy

  I just bought a new power supply (Corsair CS650M) because someone has suggested that it would be a good replacement power supply for my HP model which is HP Pavilion HPE 1090 t.   I need to know if this Corsair works and is compatible with my system, because something is not working with him directly or I did something wrong.    This is my first install and when it comes to the ins and outs of power amplification entry & exit and amperages I get so confused about this stuff.   But I think I took all the pluged connection correctly, at least when I re-plugin my old PSU after the installation to fail, I had the PC working again, what made me give confidence that I did the Corsair install correctly.  But what happens is after the installation of the unit from Corsair and turn the system he clicked power off after about 10 seconds or more and then restarted after a few seconds, then stopped again and turns off after another 10 to 15 seconds, and nothing would come up on top of the screen no more.   The first time I did the research what PSU would be compatible, I was getting conflicting results with a few places on the net saying that the majority of the HP out there (excluding some models such as the slimline) could be replaced by different manufacturers and higher power PSU, while other places I looked different.   Even the person who recommended me this power supply said in his post that he installed a Corsair HX650 model in its HP PC, and it worked very well for him.  Now, after the failure of the installation for the next few days, I did a lot more research and when I went on the site of HP and looked up the specifications of the model my PC I noticed under the power supply section, he had a heading that says "must select one of the following options" (in fact most of the different sections shows that the title too) and then he showed only two options 460W and 600W.  Then he asked me if it's the only option I get with my model.  And then I looked at my model number HP on the HP PartSurfer and under the section of the PSU, it also registers only 460W and 600W.   So who is?   I have to stay with only these options two HP or can I get a power supply with a higher power a bit then 600W from a different manufacturer that is what I want.    If I can get something that is compatible other than the options listed HP please let me know, or if this Corsair should work someone please let me know.   I need to return it otherwise.    My specs are below.

  Thank you Aaron

  HP Pavilion HPE series
  Model No.: h8-1090 t CTO Desktop PC

  Name motherboard manufacturer: IPMTB-TK Pegatron HP/Compaq name: Truckee

  PIC of the motherboard link: http://support.hp.com/us-en/product/HP-Pavilion-HP E-h8-1000-Desktop-PC-series/5080764/model/5117795...

  Original HP installed: AMD Radeon HD 6570 (Bronco) graphics card 1 GB Model: 648533-001, SP # 659355-001

  Link video card PIC: http://www.ebay.com/itm/111761368505

  Nothing has been added/modified recently real system.  Last change was the beginning of the year 2015, which was a new 2 TB HDD and added however problem memory only started about 3 weeks ago.  The Interior has been cleaned (diffuse can)

  600W Μatx Estar v5 HF PSU (Petrus)

  Information about the current hardware out of the Power Supply Unit

  Switching power supply
  Model: DPS-600WB A
  Part number: 633186-001
  600W power MAX

  Output: DC output rating (new Corsair PSU)

  + 12Va = output DC 16A = + 3.5V / + 5v / + 12v /-12v / + 5vsb

  + 12Vb = 18 a Max Load = 25 a / 25 a / 51 / 0.8 a / 3a

  + 12Vc = 12 a Max comb = 130W / 612W / 9.6W / 15W

  + 12Vd = 10A power Total Power 650W

  + 16 5.08V = side of AC input

  + 3, 3V = 15 a AC input: 100V - 240V

  + 2 5.08Vsb = current: 10A - 5A

  -12V = 0.3 frequency: 47 Hz to 63 Hz =

  Entry:

  100-127V ~, 50-60 Hz, 10 a

  200 - 240 v ~, 50-60 Hz, 4A

  You are welcome.

  Although there is a limit to the amount of power that is needed to power your computer, it uses only the amount of power it takes to power the computer correctly.  The extra power is kept in reserve for the purposes of art.  Thus, you cannot really bad the computer with extra power or amperage.  You can sleep on this point.

  Indianaak wrote:
  

  Thank you very much for your quick response, I wasn't getting anyone to answer the previous post.

  If your saying these HP spare parts are not exclusive to the company?  Some connectors may be owners, but most are not.

  It should work then?  Yes.  I've recommended hundreds of the PSU in the years I've been helping on the Forums; in fact since about 2002.

  How about the input/output & amperages of note that I registered?  As I understand not all this jargon, I want to assure you that I have / using correct notation for my system.  I don't want to fry one of my compondents with to much amperage.   Well, either I did something wrong installing or this power supply is a dud then.  Read my explanation at the top of the page.

  As I said before I pretty sure I had all the right connections, what can you tell me if it sounds right for you.  I have pluged in both connectors wired on the motherboard which were the main ATX 24pin power connector and the EPS/ATX12V 8 pin which I shared and pluged a piece of the cable labeled 'CPU' in slot 4 pins on the montherboard labeled ATX CPU.  Regarding the other split 4 pads, I don't see anywhere, it could be pluged into the motherboard.  If two 4-pin connectors were even marked, it should be good.  However, you can try to plug the other 4 pin instead of this, just to make sure that the right pair is connected to the processor power.

  My AMD Radeon HD 6570 1 GB graphics card is the type that is fed through the MB so I didn't use any of the PCI-E cables 6-8 poles.  It is very good.

  And so the only thing I had left that I have pluged the compondents of Sata cables that was my Bluray burner, my 2 TB hard drive and my USB 3.0 card.  They are very frank.

  Yet once again being installation of hardware in my system let me ask hopefully not a stupid question, but when you connect compondents Sata cable, you must have the plug-in in a particular order of wiring compondent or how do you?  I don't check the specifications of your power supply, but I think most of them have a single 12V rail.  If this is the case, you don't have to connect them to any order.  If there are two rails, it is best to divide the power of each rail.

  On my old PSU, it has an extension cable SATA used to connent card USB 3.0 which is pretty tightly squeezed between graphics card and sound card, so I guess I could use the extension cable with the new PSU POWER Sata wiring without any compatibility also publishes, right?  This should be no problem I can think of at this point.

  Thanks again for your help, I'll probably will try and plug it once more and see if I can make it work.  If this does not work for now, I strongly suggest that you contact Technical Support of Corsair for help.  They are the experts on their products and grab any errors that we do.  It is very difficult to diagnose a problem by far.  When you have done with this project, you will no longer be the excuss you are a novice. You will have a lot of knowledge that you did not when you started.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP pavilion hpe h8-1020: evga geforce gtx 950 in hp pavilion hpe h8-1020

  Hello guys I have a hp pavilion hpe h8-1020 and I am looking to upgrade to a nvidia gtx 950 is it compatibile, what I need to supply?

  Hello

  There is a unknown specification for your motherboard that will prevent you from installing a new 3.0 PCIe x 16 graphics card. Maps 3.0 is backward compatible with PCIe x 16 2.0 slots. Your motherboard may have a PCIe x 16 1.0 slot. None of these options below works on your PC if you have PCIe x 16 version 1.0

  The Radeon HD 6570, an option to purchase, is a PCIe x 16 card USB2.0. You can have a 2.0 slot. It is unclear when we look at the characteristics of HP for your PC.

  I got a HD 6570. You could not install drivers from AMD with the version of HP of this card. You need to use the HP drivers. It is possible that this card is not a 2.0 card even if the consumer version is a USB2.0 card. We can only guess.

  MSI is rolling out hybrid Nvidiacards soon. Try anything tangible yet seen. NVIDIA is slowly releasing the 1000 series cards that require less power. Maybe some OEM will also include hybrid versions that will work on your PC any time.

  The 900 series Nvidia graphics cards need the UEFI BIOS.

  Your PC has a legacy BIOS.

  You have a 300 Watt power supply. You will have to upgrade from food to run a card AMD and respect the strict minimum if you can install a TG 640 GDDR5 map.

  You may be able to install (you need a PCIe x 16 slot 2.0) Nvidia 600 series cards or watch hybrid of AMD cards by Sapphire.

  AMD cards are longer and require larger power supplies.

  You should check that you have the power and the room to install two graphics cards. The cards are also double slot. You will need to verify that you can install a card double slot. Even once, you need a PCIe x 16 slot on the motherboard 2.0.

  See you soon!

• HP Pavilion HPE h8 - 1380t CTO: compatibility problems, ask questions about knitting-by-turn or possible motherboard replacement.

  I recently baught an EVGA GTX 1060, as this 630 became quite long in the tooth and I thought that I would try to future proof myself a little as the rest of my components seem to be working very well.  However, I can't get the map to work correctly on this particular computer.  Oddly enough, I can get past that screen startup finally after several short beeps and let it sit, but it takes fowever to reach the office and clearly is not executed properly that the resolution is wobbly and software from Nvidia cannot even detect the card.  I guess I had got this far because of the onboard graphics of some sort, but AFAIK this motherboard which lacks.

  I know that the card works fine as I tested it in my other Tower, so I struggled to find a solution.  So far, it seems that the problem is most likely the motherboard, as HP does not have a new BIOS for it since the beginning of 2013 (which I did go ahead and install it).  If true, I find myself with either two options, it seems that the ditch system, entirely or find a motherboard that works with all my old components.  I'd rather not have to empty this workaholic, when all other parts work great, if it is not a work around I would like to know if there are motherboards I could pass that would work with the rest of my components.  Normally I would not bother with even apply for, but I hear a lot of chatter on HP PCs pre-constructed having compatibility problems.

  I bought this computer there is in the case of four years that I would be able to update as I do with any other PC, but I didn't know at the time that HP has a tendency to not update the BIOS settings for anything beyond a year which I admit is incredibly frustrating.  What is done is done however, and I want to make this work without having to clear the entire system.

  Desktop HP Pavilion HPE h8 - 1380t CTO

  Model #: B4J28AV
  Serial number: 2MD2290502

  Motherboard: 2ACE "Pittsburgh" Pegatron Corporation

  Processor: Intel Core i7 3820 3,60 GHz 'Sandy Bridge - E.

  RAM: 10 GB of DDR3 memory

  GPU (stock): Nvidia GeForce GT 630 (this is replaced by the EVGA GTX 1060)

  @Faver, welcome to the forum.

  Your problem is the BIOS.  However, it is because the 1060 GTX requires UEFI in the motherboard instead of a standard/Legacy BIOS.  HP didn't start using UEFI until mid-October 2012.  The BIOS may not be upgraded in the UEFI.  The last cards only not for UEFI were the GTX 660/670.

  MSI made cards with a switch that can be used with a Legacy BIOS or UEFI.  If you decide to go this way, you must contact their Technical Support to help them choose the best card for your system.

  The upgrade of the motherboard can be a problem.  HP has taken advice their specifications.  Therefore, they are not necessarily the same as the commercial versions.  Please make sure that the holes in the motherboard matches the accessory in the case.  In addition, some members have had problems with the connectors in the connections case before, for example, the power button.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP Pavilion HPE h8-1234: upgrading the 7450 Radeon HD Nvidia GeForce GTS 450

  http://support.HP.com/us-en/product/HP-Pavilion-HPE-H8-1200-desktop-PC-series/5187019/model/5231572

  I would like to replace the default Radeon HD 7450, which was built in desktop and replace it with a Nvidia GeForce GTS 450, my question is, is it compatible with my motherboard? Everything in the desktop computer is the same, except that I replaced the power supply with a Corsair CX600. As is all other compatible with the motherboard Angelica 2 graphics cards? Thank you!

  Shadgam, welcome to the forum.

  New after the 640 GT video cards require UEFI in the motherboard instead of the standard BIOS.  HP didn't start using UEFI until mid-October 2012.

  I see no reason why the GTS 450 (see card) is not working on your computer.  Your motherboard has a PCI Express x 16 (Gen.2) slot.  You can always call the manufacturer's Technical Support to make sure the card you have chosen will work.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion HPE h8 - 1213c: black screen of death because of the new graphics card (EVGA geforce gtx 960)

  I just bought a new card (EVGA geforce gtx 960) to kick some butt. But during installation, it seems to be held on a black screen of death? Not the most fun to see... in any case, I had asked the store clerk if it would work and he said to, but it doesn't seem like it does... Is there a new BIOS I should download or something? Any help would be nice...:.

  My computer is a HP Pavilion HPE h8 - 1213c

  The graphics card is an EVGA geforce gtx 960

  If you have both. You can use one or. PIN 8 can be used as a 6 pin as well.

  http://www.EVGA.com/products/ProductList.aspx?type=0 & Family = GeForce + 900 + Series + Family & Chipset = GTX + 960

  2 smaller cards use a single PIN 6. The rest use a single 8 pin.

• Pavilion HPE h8 - 1380t: video card upgrade for Pavilion HPE h8 - 1380t

  Hi all

  I recently bought a map GTX1060 (from a MSI GeForce GT640) 4 year old GPU from nVidia in line in order to improve the capacity of my machine so that I would be able to play Fallout 4 and 3 Witcher (both put my poor old GT640 kneeling - even on lower resolution settings).  It is part of the case and the powers that be (Yes, I plug in the connector 6-pin PSU) and 600W POWER supply is adequate for the task, but I'm starting to think that I probably have a motherboard compatibility issue.

  When I install the card and turn on the PC, it hangs at the splash screen of installation (a common problem from what I've already read on these forums) and that it goes no further (keyboard and mouse do not respond at this time here).  I contacted the nVidia support, and they suggested some changes to the BIOS (disable Secure Boot, activate the Legacy/MSC Mode and switching between legacy and UEFI BIOS selection Mode), but when I access the HP configuration utility (F10 on boot to top with GT640 card installed), these options are not put at my disposal.

  Is it possible for me to access the BIOS settings that nVidia has indicated I should be adjusted?

  This GPU card simply is not at all compatible with my motherboard?

  System Specs:

  HP model number: B4J28AV #ABA (Pavilion HPE h8 - 1380t)

  Motherboard: Pegatron 2ACE(Socket 0); 1.08; Intel Sandy Bridge-E Rev. 07; Intel Southbridge X 79 Rev 05

  BIOS: FRIEND 7.15

  CPU: Intel Core i7 3930 K (3.2 GHz)

  OS: Windows 7 Professional 64-bit, SP1

  Current GPU: MSI GeForce GT640; Driver 10.18.13.6881

  If the GTX1060 is not compatible, which is the highest card GPU nVidia performance that can be used with this motherboard (given the limitation of power supply 600W)?

  Is there another motherboard for this machine which would be compatible with my existing CPU and the GTX1060?

  Thanks for your help...

  Hello

  The h8 1380t has a Pegatron motherboard 'Pittsburgh '.

  You could try to find a future revision of this motherboard. I'm also a 810-150se with a map of the 'Pittsburgh2' system that has UEFI. I use a card Nvidia GTX EVGA FTW 970 with excellent results.

  You will need to check that the Review Board would fit in your frame.

  The other options are:

  1.new want to expedition with Win 7 Pro, or

  2 falcon Northwest.

  In a map of the main current system the permutation of Asus, Gigabyte or Asrock is difficult at best. You have to change other components such as the processor, heat sink, fan and the memory. You can probably buy an OEM of Windows 7 Pro version.

  It becomes quite expensive when you do the math on all of the changes you will have to do. There is no guarantee that you can find a map of the main current system having the correct spacers for your chassis h8 - 1380t.

  Avoid a Skylake processor if you can unless you don't mind jumping through a few extra hoops to install Win 7.

  Please consult this article and go here for the workaround resolved the problem installing win 7.

  Jay

• Upgrade GPU of HP Pavilion HPE h8-1070uk desktop PC

  Hey everybody would be able to tell me which graphics cards are compatible with

  HP Pavilion HPE h8-1070uk desktop computer? I tried to install Asus gtx 750 TI unsuccessfully as the phones was not compatible due to the bios, and now I don't know what card to get.

  Please help, thanks.

  You are welcome.  I'm happy to help you.

  The original video card has a switch that changes the EUFI after-effects.  Your computer has the Legacy BIOS.  The card was recommended to several members of the forum and there has been no reports of problems.  It's good that you're running Win 7.

  If you are uncomfortable with the card you can contact MSI Tech Support for help.  They are the real experts on their products and will be happy to help.  It's good to let them know that you're new on the subject of video cards.  They will understand.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion HPE h8 - 1010t CTO D: the GPU upgrade, now the PC will be unbootable, or even POST

  I visit my father. We strive to upgrade the GPU in its Pavilion from HP running Windows 7.
  
  http://support.HP.com/us-en/product/HP-Pavilion-HPE-H8-1000-desktop-PC-series/5080764/model/5140202
  
  The PC was shipped originally with a GPU Radeon HD 6450 (1 GB). It has only 2 video, outputs and he wanted to add a third monitor. I recommended he buy a new GPU. He bought a 260 X XFX R7.
  
  http://xfxforce.com/en-us/products/.../AMD-Radeon-R7-260x-core-Edition-R7-260x-cnf4
  
  Also, we went to electronics, Fry's and bought a new power supply, a N500 Lepa, which is a power of 500w. We have successfully installed your new diet.
  
  Now, when I removed the old GPU, and put in the new GPU, PC turns on, the Red led light on the front comes on and stay red, but the PC unbootable. The screen is black, and it is not initialized.
  
  I once forgot to connect the power supply to the GPU. That day the PC started to boot the system & I was able to use logmein remote inside to turn it off, but once the machine was turned off again and I plugged the power of pin PCIexpress 6 pay-per-view, same behavior. PC is out of warranty w / HP, so that they are without help.
  
  I went to the website of HP and the BIOS update. still no luck.
  
  We have added some third-party RAM. I tried to remove the third-party RAM to see if it was the question. Does not solve it. I tried to remove the OEM ram and install just the 3rd part of RAM, but has not made a difference either.

  There is not BIOS version 8 available. Your situation is not a happy scenerio.

• HP pavilian hpe h8-1205: my gforce 740 graphics card does not work in my HP Pavilion HPE h8-1205

  My 740 gforce graphics card does not work in my HP Pavilion HPE h8-1205, please help

  Supaman4040, welcome to the forum.

  I think that your problem is related to the BIOS.  The 700 series video cards require UEFI in the motherboard instead of a standard BIOS.  HP didn't start using UEFI in its motherboards up to mid-October 2012.  Your computer was released January 25, 2012.  You must contact the card manufacturer to see if they have a VBIOS update which will allow the card to work with your computer.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• How the Pavilion HPE-150 t has 6 GB of RAM with 3 DIMM slots

  Check the specifications for the Pavilion HPE-150 t, I see that HP currently offers a free upgrade to 6 GB of RAM (from 4 GB.) What I don't understand is that these 6 GB of RAM are provided in 3 DIMMs.

  The only setting I can think of that allows two-channel with 3 DIMMs mode in this situation is to have a pair of 1.5 GB DIMMS in channel A and a single 3 GB DIMM in channel B.

  However, AFAIK, DIMM is not sold in one of these densities (1.5 GB and 3 GB.)

  Can someone explain this for me, please?

  As far as I know, HP is not the "Dual-channel" advertising - they simply offer amount:

  http://www.shopping.HP.com/series/category/desktops/HPE150t_series/3/computer_store?JumpID=reg_R1002_USEN

  FREE UPDATE! 6 GB DDR3 1333 MHz SDRAM [3 DIMMS] from 4 GB

  http://support.HP.com/us-en/document/c01976259

  It is highly unlikely HP POP just in an extra 2 GB DIMMS.

  The only way you can get dual channel of this mobo is to fill the memory DDR3 DIMM 2 and 4 or all 4 DIMM with the same type and density.

• Pavilion HPE H9-1130: install the firewire card correctly into the slot of the motherboard correctly

  Hello, for my HP Pavilion HPE H9 1130, how to install the correct firewire in the motherboard slot card OK in OS Windows 10 x 64 / x 64 processor? And what video software system can I download to recognize my Panasonic 100a camera AX?

  Thank you. Followed your instructions. And it worked perfectly. Thank you. Even if I have Adobe Prem Pro, I downloaded MS Director and put 9 drivers after installing the PCIe card. Then it worked perfectly to capture video from a FireWire camera. Thank you once again!

• HP Pavilion HPE h8-1111: Deffective WLAN Card

  I've had a few confusing issues with my internet connection for a few weeks now:

  My computer seems to detect wifi networks (they appear in the Network Manager), but fails to connect because of an unknown factor.

  Basic troubleshooting informed me that wifi wasn't the issue (other devices could connect to) and it turns out that my computer could sometimes reconnect by mmee after a few hours (weird right?)

  This time it does not resolve itself. I tried to update my WLAN card through my laptop adapter, so the drivers via a USB key. Nothing worked (maybe bad drivers?) I've tried a few)

  My network card is a mini Broadcom 802.11n using magnetic antennas of the card. (youd cloth found in a laptop essentially...) I have little or no knowledge more than I could translate from the web on this kind of hard\software. I am at a loss.

  [Also, I've seen a few threads recommending the driver intel update of software, but it needs a connection to work its magic...]

  Hi @arnaud34,
  
  Welcome to the Forums of HP Support! I understand that you have problems with your wireless connection and I'm happy to help you.

  Is that something WLAN adapter that you added or the original map?

  The Support page and drivers for your computer model: PC desktop HP Pavilion HPE h8-1111

  I would recommend that you try the following to see if you can get a stable connection. If at the end you still have nothing so it may be that the card is bad, and a replacement is necessary.

  Troubleshooting your wireless network and Internet access (Windows 7)
  
  In addition, you can watch the the power management of your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Forget the network: (Windows 7)
  1. press start.
  2. tap manage wireless networks, click on the application at the top of the start menu.
  3. right click on the network, and then click on remove network.
  4 confirm the warning by clicking OK.
  
  Reset TCP/IP on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here, but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  Please let me know how it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.