HP Pavilion Notebook pc: camera turns is not on

Similar Questions

• I have a HP Pavilion notebook. My system does not detect my sd card and I can't eject. Help?

  Original title: undetected sd eject not

  I have a HP Pavilion notebook. My system does not detect my sd card and I can't eject. Help?

  From my understanding, most laptops allow you to simply remove the SD card back.  Others have a simple spring mechanism that requires you to press the memory card slightly until you hear a "click", similar to a click on a retractable pen, which must eject the card.

• HP Pavilion Notebook - 17-f250: new SSD not recognized, Pavilion 17 AMD drivers

  Hello

  I bought the laptop (HP Pavilion Notebook 17-f250) on September 2015 and this September 2016, I decided to upgrade with a 2nd SSD.

  I bought a caddy, placed my SAMSUNG EVO 850 PRO inside, removed the optical drive and then place the CART inside the laptop. It fit perfectly, no problem there.

  But Windows does not recognize it at all in MANAGEMENT OF DISKS.

  It is not here in order to format it, etc...

  My IDE/SATA appears as "AMD SATA CONTROLLER".

  I can not find anywhere no possibility of enablev AHCI etc... My BIOS is not an option to check if the AHCI drivers are enabled or not.

  With the AUTOMATIC DETECTION is my driver: AMD APU A4-6210 with graphics AMD RADEON R3.

  My operating system is WINDOWS 10.

  FYI, I bought another same SSD for my office and worked smoothly. I only have a problem with my laptop, and I can't figure out how to recognize the Windows SSD!

  BR,

  Dionisis

  What caddy you bought? There are a lot of these on the market and some are not made with the highest quality control. You may have it tested with another hard drive?

  Second, the interface for the optical drive is SATA which is ahci. The drivers are not the issue.

  Finally, put an SSD in an optical drive is a little excessive spending from one optical drive interface is slower, so the speed of SSDS is wasted. It would be much better to put a regular hard drive large, slow in the optical Bay for storage. Having an SSD in there won't be fast in all directions. Also, a disc in an optical Bay will not be initiated.

• HP Pavilion Notebook 15p204tx: Realtek RTL8723BE does not

  Hello

  I was faced with a problem with my Realtek RTL8723BE wireless card for more than a month. After using it for awhile, I am unable to connect to the internet. The connection status indicates "No Internet Access". After you run the troubleshooter, it says "one or more network protocols are missing on this computer." This problem won't recover unless I have to reboot the device.

  To solve this problem, I've updated the software device driver to version 2023.23.1030.2015 and even after the update, the problem seems to persist. The only way that I am able to connect to the internet using the Ethernet cable.

  I tried several methods over the internet to recify the question and nothing seems to work. I tried to run the

  netsh int ip reset resetlog.txt
  

  After fixing the registry as shown in the video https://youtu.be/G3DpeeXLSDM , but it did not work. I also followed all the instructions in the video https://youtu.be/HJyBaP3AC74 and the problem persists.

  Now when I run the troubleshooting software, he says that he was unable to identify the problem. Now, I'm completely unable to use WiFi on my laptop. I would be grateful if you guys could help out me!

  Thanks in advance!

  Gillot

  HI @adithya-n,.

  Thanks for the information.

  Here is a link to the HP Pavilion Notebook - 15-p204tx software and drivers. Please select Windows 10 and click Refresh to display a list of recommended drivers.  You can also run the HP Support Assistant to help get and updates from HP.   If you are unable to access the Internet, I would like to do a clean install of Windows 10.  How to clean Windows Installer 10 (from tenforums.com)

  Please let me know if it helps.

• E8B15UA #ABA: my hp pavilion notebook is needs a driver not sure what I need or how to fix it

  I have a hp pavilion notebook. There is a yellow exclmation point next to the unknown device. I looked at other positions. I don't know how to solve this problem. One post said I had to unzip a file and save it to solve the problem do not know how to do this. Help, please

  I need the hardware ID of the unknown device to eliminate other conjectures.

  Go to Device Manager and click on the unknown device in need of a driver.

  Then click on the Details tab in the upper part of the device window unknown.

  Now, you see a drop-down list of property and it is set by default to the Description of the unit.

  Drop down on it and select the hardware ID element

  After the first string of characters you see in the window.

• HP PAVILION NOTEBOOK PC - sound G6 does not work properly, "crackling".

  Hiya,

  The laptop was having problems, so I nuked it and reformat the hard drive and reinstalled Windows 7 64 bit. I downloaded the drivers for audio here - http://support.hp.com/us-en/drivers/selfservice/hp-pavilion-g6-1200-notebook-pc-series/5145704/model... I didn't know that was what I wanted for the sound itself for the speakers, so I downloaded each, uninstalled the previous until I had some kind of result, the one who gave me a result was "IDT high definition CODEC. When I click on test in reading, she sometimes plays nothing but another time parts of the carillon will play and cut, in a sort of crackling. Videos YouTube do not seem to want to play either, so pilots himself seems to have installed, but obviously it does not work as expected, so I'm stumped on how to fix it. Little help would be much apprechiated.

  HP Pavilion Notebook PC g6
  Product number: A7D64EA #ABU

  Since I am from a tech background, I think that its in my best interest to give the same kind of help that I would see when I googled these questions.

  Many thanks to @Dvortex who, in a different thread, gave this advice, which totally fixed my problem. I hope this helps someone coming through this.

  Go to Device Manager (you can give a right click on the windows logo on the lower left corner of your screen and select Device Manager from the list)

  Now to maximize the "audio, video, and game controllers" in the list. You will see the audio driver. Right click on "IDT high definition audio CODEC" / "Realtek audio CODEC" and select "Update driver software".

  Choose "Browse my computer for driver software" - choose "Let Me pick from a list of drivers for devices on my computer.

  Select "High Definition Audio Device" (not IDT high def... or Realtek High Def... This is important) and click Next. You get a warning message but answer 'yes '.

  Once windows have updated driver software, try to play the audio again and check.

• Pavilion Notebook M1Y13UA #ABL: clickpad does not respond immediately when you tapoterez

  Hello

  I have constant problems with the clickpad installed on my laptop. I can say that it is the touchpad/clickpad WORSE I've EVER had. It has been repaired twice by HP under my warranty coverage. First of all, they have changed a few son/cables inside and completely uninstalled Windows 10; Then, because the problems were still present, they installed a new clickpad, which changed the hardware. Some issues have been resolved, but others continue to be present.

  At this point, I'm trying to any parameters used for the clickpad, via settings-> devices-> mouse and touchpad-> properties of the mouse-> settings-> properties for Synaptics ClickPad ClickPad, very often, but not always, the clickpad is not responding when I type the first time after that I was doing something else. When I type the second or third time, I'm finally starting to get answers. In other words, whenever I type somewhere - to close a window, to follow a hyperlink, to place the cursor in a text, to select a part of a text, etc. - my first tap does NOTHING. I must repeat my cock at least once more before there is a response. I can type very gently or hard, it doesn't matter. It applies both to pressure alone to double tap. It is the same for the two fingers tapping.

  Pointing-> sensitivity feature is at its maximum. (If I reduce, the clickpad becomes even more that don't meet liked). Smart Sense functionality is almost extinct. (If I put it near Max, nothing changes.) Filter activation time option, which apparently blocks the clickpad for a certain period of time after you type, is zero. For the feature settings-> devices-> mouse and touchpad-> Touchpad (to help prevent the cursor to move accidentally while you type, change the time before work clicks)-> without delay. Turning or turn off of the button (on the clickpad) doesn't change anything. Clicks properly. All the drivers are up to date. All Windows 10 operating system up-to-date. When I attach my USB mouse, the mouse works fine, there is no delay in responses.

  I assumed that contacting HP for the third time will be not successful. Anyone have the same problem? If so, how to solve it? Other users seem to have had a similar problem (http://h30434.www3.hp.com/t5/Notebook-Hardware-and-Upgrade-Questions/Synaptics-Clickpad-Smartsense-M... but not found a solution.)

  Thank you very much in advance!

  I think that I recently found a solution (a partial solution at least) for this problem. The root of the problem seems to be the drivers supplied by Microsoft. The pilots, even new ones, for this clickpad are just horrible.

  What is worse, updates to these useless drivers are installed in my system without any agreement from me either. Try to avoid updates, using a Microsoft program (https://support.microsoft.com/en-us/kb/3073930 ), doesn't help - for the clickpad updates are installed in any case.

  What I did to make my clickpad works much better is the following:

  1. Download a driver directly from the author of the clickpad, Synaptics (http://www.synaptics.com/resources). For my camera, I used "Windows 10 I2C v19.0.19.1 devices". Do not install the driver again, your system will you not allow to do so due to a 'new' version of the driver 'already installed '.
  2. Disable automatic updates of your operating system, using the Protocol according to (http://www.thewindowsclub.com/turn-off-windows-update-in-windows-10). This change is not permanent, you can always activate the automatic system updates, if you wish. Of course, if you enable automatic updates, Microsoft crap drivers will be installed automatically too, deletion of all other good drivers you have installed previously.
  3. Completely uninstall the driver automatically installed for the clickpad using Device Manager (you can advance this Manager by right-clicking the Start button). Restart the computer, as required in a message box.
  4. Install the driver previously downloaded from Synaptics. In my case, I don't have to install manually, my system installed this driver 'default', without doubt, as the only available driver for clickpad on my hard drive.

  Here are the steps that I have lived to correct the problem. Now my clickpad is not as frustrating as it used to be. Make sure when you try these steps, they may not work in your particular case, because your computer might have a few important differences from my camera.

• HP Pavilion - 14-ab020tu: ab020tu HP Pavilion Notebook 14 - Wlan driver does not work

  I just bought "HP Pavilion - 14-ab020tu ', installed windows 8.1 pro, downloaded drivers and it seems it works perfectly but wifi.

  When I tried to install this driver Broadcom WLAN (http://support.hp.com/vn-en/drivers/selfservice/HP-Pavilion-14-Notebook-PC-series/7771364/model/8189...

  his charge at the halfway point on his instalation and drops then a message appears and asks me if the program worked well.

  Ive tried to install this driver under Mode safe and in charge of the installation, but when he was installing an error came out saying that the installation cannot continue because update.cpp 1205 is not found or something. I also tried to find the driver from broadcom site, but could not find.

  And now I can use e-net only via cable.

  Can someone help me with this problem?

  Hello:

  See if this driver works...

  FTP://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69929.exe

• HP Notebook: HP laptop turns is not on / boot the system.

  I have a HP laptop and every time I turn on the HP logo comes on, but after seconds, the screen goes off and then returned to the logo and so on.

  I tried everything, remove the battery, turning on/off, closing the display, retrieve the BIOS, etc..

  PS. It used the Windows 10 operating system.

  PSS. On the BIOS, there only the Configuration of the security system, output and hand options, somehow does not include diagnosis so I can do a test, and I can't update the BIOS if I can't reach the window.

  I would really appreciate if you could answer as soon as possible.

  Thank you.

  Hey @Shadow5300, welcome to the Forums of HP!

  I'd love to help you with your laptop. From your description, I understand that you are unable to start past the HP Logo, nor can you run the diagnostics. According to the following document, given what you have already tried, it might be time to do a system restore: HP Notebook PC - computer won't start (Windows 10).

  Let me know the results of your efforts and if it helps to solve the problem, please click Accept as Solution button below. Thank you.

• HP Pavilion Notebook e153sa 17: we could not retrieve the list of drivers for your product.

  "We could get a list of drivers for your product.  Please select the desired operating system and select "Update" to try again "." This continues to be when I try to search for new drivers for my camera and nothing comes same afteri put it in my operating system options. How can I get my drivers to come?

  Hello:

  I had no problem... I see a complete list of the W8.1 drivers for your model.

  http://h22207.www2.HP.com/us-en/drivers/selfservice/HP-Pavilion-17-e100-notebook-PC-series/5401229/model/6732730

• HP Pavilion Notebook 15-p035nd: Bluetooth does not

  Measures taken before posting:

  -Update driver Bluetooth through the support of 3hp.com

  -several reboots

  -disabled + material bluetooth enabled

  -several good bluetooth devices doublechecks works next to the laptop: work and the pair with eachother, but not to my Pavilion

  -checked the bluetooth compatibility: it should be compatible because should always match a lower/higher generation, so I found on the internet (3.0 for both devices / 4.0 for my laptop)

  Bluetooth on my laptop does not work because two devices (in same color or unmatched situation) closely placed next to my laptop is I have search for devices via "Devices and printers" + "add a device". Bluetooth is activated via 'Pc settings' + 'Airplane Mode' where you can turn Bluetooth power on or off.

  Would you please support me and give me a hint of something that I have not yet tried? Thank you for reading my post.

  In Regedit (via Windows + R button) I put a value of 1 in the Bluetooth folder (hkey current user / Panel / bluetooth - box Notification + rightmouseclick icon + modify)
  
  In Regedit (Win + R), I put the value of 6.3 to 6.2 (hkey local machine / software / microsoft / windows NT / current version - current version + rightmouseclick + modify)
  
  + Restart

  Result:

  My laptop CAN find (other laptop + mobile phone) devices now but not the device, I want it to find. Since he works on a technical level, I guess this thread could be closed because I can't be sure at this stage that my lodge does not work correctly. All the steps that combined my work could certainly be useful to others if.

• HP Pavilion Notebook (laptop) plugged, G6 does not support.

  Hello

  I bought a laptop HP Pavilion G6 just a couple of months, and I had this problem since the beginning. I looked at some other forums and it seems that many people have had the same problem with the laptop is plugged in, but does not support.

  This problem is really frustrating, as the laptop is connected to the power source and in the laptop, but half the time it is not yet registered as being connected. The battery is discharged. Once or twice the battery completely exhausted (while it's plugged in) and then was charged 100% next time, it was shot on(???!!!).

  Could you tell me if there is some sort of programming or software failure, or if it could be a hardware failure. I have run the checker battery several times and each time he found no problems with it. As the laptop sometimes acknowledges that it is indeed connected (but does not load) personally, I think that it is not a problem with the AC adapter.

  PLEASE HELP ME!

  Thank you.

  (Sorry for the long message)

  Hello

  You can help us help you by displaying the following information.

  1. the complete model number and the laptop Nr - see web document this HPif you're not sure you how to locate the product number or model number.

  2. the full version and the name of the operating system you use (IE Windows 7 64-bit).

  Go to Device Manager. (type device in the search programs and files and click on Device Manager, as shown in the following image)

  

  Expand the device of Batteries.

  Right-click on the compatible Microsoft ACPI control method battery and select uninstall.

  Do the same with the device adapter Microsoft.

  

  After uninstalling the devices, then you can right-click on one of the devices in the Device Manager and select and click on check for material changes.  When you have done this, the operating system will reinstall drivers for the devices.

• HP Pavilion Notebook - 15_p151: Wi - Fi adapter, not recognized in Device Manager

  Earlier, the laptop was to have very well internet, but after installing a new driver for the Realtek RTL8188EE b/g/n, the adapter has stopped working. Currently, the Device Manager even if hidden devices are displayed in the wi - fi adapter is not demonstrated. If someone can help me as soon as possible it would be greatly appreciated.

  EDIT: After some time, the network has been shown in other devices and now appears under network with an exclamation point cards; When I look at the properties, it says "this device cannot start. (Code 10) This device does not exist. "Looking at my drivers, the current version number is"2012.14.417.2014 ".

  EDIT 2: after the reset, the wireless driver currently said to work by the Device Manager. After a few minutes, the wi - fi adapter ("of which there are two adapter Wi - Fi Realtek RTL8188EE 802.11 b/g/n and Wi - Fi 802.11 RTL8188EE Realtek adapter b/g/n #2 both give")

  Currently, this hardware device is not connected to the computer. (Code 45)

  To resolve this problem, reconnect this hardware device to the computer. »

  Interesting...

  See if this just driver installation replaces the existing one.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149801_1

  You can also try other revisions of the pilot by clicking the history tab of revision on the driver page.

  If it does not, unfortunately, I don't have any other suggestions for you to try.

• HP Pavilion Notebook 15-P144NE: battery and not charging

  Hello

  I bought a laptop from Doha yesterday and now I am in India. I used the computer laptop 2nd time, 1st time, I loaded the laptop and used but yesterday I do not charge the battery and used with Player in the charger. After a few hours battery drained after im pluggin installed in the charger yesterday. I left it on my table by putting the charger cable. But nothing happends... When I click the power button the flashes 3 times during 1 second.

  How to activate the laptop suggestions?

  I would try reinstalling the memory to see if any change - or withdrawal of one then the other-if you have two - to see if it will start.

  Since you are under warranty, you'd be better off calling HP support.

  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

• HP Pavilion Notebook 15-p261sa: turning off Beats Audio HP pavilion Windows 8.1

  Wow, Beats Audio is terrible... it's quiet bits bits high and very quiet! It is also mess with equalization.

  How can I activate it took off and get the sound as it was supposed to be?

  There are a couple of similar positions, but these are not re Windows 8.1

  Thanks in advance.

  I think that I have solved:

  I went into Control Panel - programs - programs and features and deleted the program "Realtek High Definition Audio Driver.

  He forced me to reboot... and now the sound seems fine.

  Why would someone sound messed around with in the first place?    ;-)