HP Pavilion p6 2000-ukm: recovery disk/boot on a new HARD drive?

Hello

I have a hp Pavilion p6 2000 ukm. Recently I started getting on my HARD drive error messages, saying it was a failure. I recently bought a new HDD in my pc. I connected it correctly and it says that I need recovery disk / boot disk.

To my knowledge when I bought this pc there was no disk Windows 7. Now I know on workstations, you create your own.

My question is... How to get windows 7 installed on my new hard drive when I plug it in? I'm looking for the iso of windows 7, I think that his name, but I can't find any .iso file.  I'm trying to install windows 7 on my new drive HARD I need not my other files like music... etc. I'm looking to get my HARD drive installed with windows 7, where it has IE and I can go back to the installation of everything I had previously. Should u use "create a system image"? Its a big file and requires 7 + dvd discs is my only option? I have my 25 key windows 7 as well.

Any help is thank you attended.

Hey,.

Here's the phone number,

02076600596

Tags: HP Desktops

Similar Questions

  • Want J010dx m7: windows will not start until after full recovery of the system with new HARD drive

    Hello world

    I need help here.

    My HP envy m7 J010dx works perfectly with my original hard drive (1 TB).

    I am preparing a second HDD (NEW 320) as backup.

    I took off the Moose HDD (1 TB) and replace it with the NEW HARD drive (320GB) and try to do a full recovery of the system with the HP recovery DVD.

    After full system recovery and laptop computer needs to be restarted in order to continue, the laptop keeps restarting on the logo of windows 8.

    I think it says device not found Boot. Also a test using the UEFI tool material HP and all pass.

    Replacing the NEW HARD drive with the original of the old HARD drive and it start normally.

    What can go wrong here in this case? Thank you very much for the help.

    Concerning

    John

    OK, I read through the thread and this is my point of view on this based on works including restore process with the user created a recovery (UCRDs) media which the user indicated that they used.

    If you just want to jump to the conclusion at the bottom, you can see my opinion. If you want to know 'why' Please read the entire post.

    Model No.: m7-j010dx

    Product #: E0K83UA #ABA

    Ships OS: Windows 8 (64-bit)

    Recovery HP part No. Kit: 730336-002 (3 DVDs + extra)

    User replaced the HARD drive with a 1 TB hard drive 5400 RPM with HP ProtectSmart hard drive Protection a new hard drive is a Seagate Momentus 7200.4 ST9320423AS 320 GB 7200 RPM 16 MB Cache SATA 3.0 GB / s 2.5 "Notebook internal hard drive.

    With the help of UCRDs sent media recovery media (SSRDs):

    When the UCRDs are created, only the drivers for the HW operation (this is a critical point, that I will look later) are burned to the user created a recovery media.  Consider this a snapshot of the current HW, the base drivers and software applications.   If you change the HW on your laptop or desktop where the additional device requires a different driver for these features, a few questions you might - recovery process could stop because he can't find the right driver, a blue screen, a lack of start-up or other unstable system.

    A few years ago, I had a PC that would not recover because the Blu - ray (ODD) optical disk drive did not work.  I replaced the WEIRD Blu - ray with a generic DVD/CD burner into the new part of Blu - ray is presented.   I got the PC using SSRDs thinking I would put some time and just install the Blu - ray after the PC has been recovered.   The PC recovered and when the new Blu - ray showed I installed the unit and guess what?  All PCs have shown in Device Manager and applications was a generic ODD - no Blu - ray capability and ability to read Blu - ray content in the default HP provided for multimedia applications delivered with the PC.  Applications were there but no Blu - ray capability.

    Huh?  It looks that I did not put any time at all.

    I inserted the new Blu - ray ODD and distributed recovery with the HP SSRDs.

    After recovery, I had all the Blu - ray drivers and applications supported Blu - ray.

    The difference between UCRDs and SSRDs:

    UCRDs provide a glimpse of what is installed and functional both disks are created.

    Version Digest of the player on what is happening with SSRDs to retrieve a PC (before Windows 10):

    SSRDs have all the drivers for all the HW and SW qualified for the unit.  There may be several drivers for hard drives, different types/screen resolutions, sides, etc.  Based on the characteristics of the specific laptop / desktop a process is run called "Do / don't.   After entering the recovery SDRD, the Notebook media boots to Recovery Manager.  The first step is a raw copy of all the contents of the disc on a temporary partition.  Following the Do / do not process looks at the characteristics of this specific unit and remove all other drivers and applications not used by this device.  Drivers and the only successful applications are the features supported.   And then, the new operating system and recovery partition is created.   The PC end recovery of cleaning process and restart the laptop / desktop. And, Yes, you guessed it, if you create the user created a recovery media, you only have the drivers for HW devices and applications of HP on the PC at the time.

    So, that being said, what could be the cause/solution?

    Hard drives can be different enough so that a different driver (not the UCRDs) is necessary for the newly installed HW.

    The SSRDs are supported on the new HARD drive installed?

    I don't know, I have an office boy, and I have not tried on this model of laptop.

    If you have / acquire SSRDs, I recover the laptop with the new installed HARD drive and see if it works.  It may or may not.  I don't know what drives were qualified for this laptop.

    If this does not work, the last option is cloning via USB connection (old HARD drive in the PC, new HARD drive connected to a USB 3 via the SATA Adapter (dongle) USB port, install or download software cloning and cloning the old HDD to the new.)   I just did this on the two older Windows 7 computers laptops using a SanDisk Ultra kit.  He has worked on both units.

    Conclusion:

    I don't think that the problem is caused from a HARD drive of 1 to a 320 GB HARD drive, as it meets the minimum specs for a complete installation.  I think the problem is related to the use of UCRDs to retrieve and the UCRDs do not have the HARD driver/firmware/application disc.

    But then again, I know.

    I am an employee of HP...

  • How to recover HP Recovery Manager after replacing a new hard drive

    Recently I have lots of BSOD saying Bad_System_Configuration_Info and I ran a boot hp test and my hard drive failed the short DST test, so I looked online and it says that this means that my hard drive has failed.

    IM planning to buy a new hard drive. I don't have a windows disk to recover my windows 7, so I tried to copy the recovery partition hp from the old drive to the new. I don't know how do it, I wonder if anyone knows. I have no recovery disks and I don't think I can order a so I want to restore my new hard drive without the use of drives and using the my old hard drives at hp Recovery Manager

    I bought the computer to the United States, but I moved to China so im assuming I want to buy a new HARD drive that is not Hp? I don't know if it will work yet cause I hear it must come from a drive HARD hp to work

    Hello

    You can choose the relevant HARD drive of any manufacturer you want, but if you want to re-create the recovery Partition, you need to do a "Factory Reset" with a set of recovery discs - if you don't have these, you will need to order them from HP.

    However, there may well be a workaroud allowing you to reinstall the operating system without having to buy these discs.

    Can you post back with what follows.

    1. the complete model number and the laptop Nr - see here for a guide to the location of such information.

    2 version full of operating system provided with your laptop (that is, Windows 7 Home Premium 64-bit).

    3. can you still read the activation key product of 25 characters on your COA label (don't post back with it, just to confirm if it is still readable) - an example of a COA label can be seen here.

    Kind regards

    DP - K

  • Recovery is possible on the new hard drive?

    Hello

    I think about buying a new hard drive to improve the performance of my laptop Satellite.
    I was wondering if it would be possible to restore my system using the recovery on the new hard drive disks.

    Thank you!

    As far as I know you can do it. What you need is to buy hard drive compatible and functional.

    By curiosity, but what model of laptop do you have and what hard drive you want to buy?

  • How to install Windows without recovery disc - Satellite A660 with new HARD drive

    Hey,.

    Portable 500 GB HDD of my friend Toshiba Satellite A660 seems to have died.
    I tied him to my laptop on a sata dock and runs a data recovery program because nothing has been saved. The recovery takes forever, however, and she really needs his computer to work.

    Because the hard disk may be damaged in any case, I am considering buying a new hard drive and install in the Toshiba.

    How can I do this without a recovery disk, though?
    The old drive was a partition recovery on it, I think, but this seems useless with a new drive.
    Operating system is Windows 7 64 bit home edition.

    The product key is on the bottom of the laptop.
    I live in Turkey and so I don't think there is a Toshiba store is close.
    There are individual computer stores, so I'm confident, I can buy a new internal hard drive (I could find the sata dock here), but he must know what to do to install the software, etc.

    Thank you!
    Chris

    > How can I do this without a recovery disk, though?

    You either have the recovery disk or you are going to install the system using the Microsoft Windows disk.
    The necessary drivers are in internet on Toshiba UE page.

    The recovery disc can also be ordered here:
    http://backupmedia.Toshiba.EU/landing.aspx

  • Will Vista Recovery DVD to install on new hard drive on my Presario

    You need to install Vista from the recovery DVDs I created when I bought my laptop Presario 3 years on a new hard drive. The original replaced HARD disk needs and I was going to buy the same exact model.

    Someone at - he did this with success, or will there be problems? Thank you

    Hello

    You should be fine with the MHW2160BH.

    Hope everything goes well.

    Best wishes

    DP - K

  • Windows XP system restore Boot Failure with new hard drive

    HP Touchsmart IQ546t running Windows XP Home Edition

    Here is my story:

    A few months ago my PC was informing me that a hard disk failure is imminent and how can I back up my data.

    I was able to get most of the data backed up and has continued to use the PC.

    Finally, the hard drive failed.

    Not being not able to find system restore disks, I ordered a set of HP.

    In the meantime, I was able to save the rest of my data using an external hard drive enclosure, a laptop and a backup disk.

    I used system restore discs to erase the hard drive and restore the operating system.

    After the successful restoration, I was able to boot my PC and use it for a few days, but again became imminent hard disk failure message. Yet once again, the hard drive failed and I was unable to use it.

    I decided to replace the hard drive, thinking I could install and use the system restore disks to get the installed operating system.

    I followed all the instructions, I find and could not start the machine to the point he will recognize the recovery disc. I receive a message that tells me to insert a bootable media.

    Does anyone know what I'm missing here?

    Is there something I can try to get the hard drive to boot to the point he will recognize the recovery disk?

    Thanks in advance for any advice.

    Hello

    OPS, sorry on this subject.  If the recovery discs are not recognized not so you act have a problem trying to get the new HDD to be restored.

    Try the procedure below and see what happens.  View your results.

    Cyberlink CD recovery for hard drives. When you created this CD, insert it into the system that fails to start, restart, and wait until you see a window with a green check mark.  Next, remove the CD and insert your first recovery DVDs.  Reboot the PC and go through the process of installing the operating system again.  If all goes well, it should install properly this time.

  • Recovery of Windows 7 with new HARD drive

    Hello Forum

    If you guys helped me with the HARD 'bankrupt' drive - and I have a new drive HARD ready to install.
    But I need to back up the operating system (Windows 7).

    I don't have an external hard drive PC configured.
    I have the DVD. I have a memory stick (empty - but unknown to memory capacity).
    There is little data to be transferred (and to be honest - if it was over it would not be the end of the world).

    So I just need to back up the operating system.
    I went in the 'create a back-up' then 'create a system image '.
    But (and I may be wrong here) it seems that if she needs a greater memory than the DVD I inserted.

    The indices here folks?

    And - waaaay out of my comfort zone. So any help is appreciated.

    Thank you.

    Helpless dad.

    > I went in the 'create a back-up' then 'create a system image '.
    This has nothing to do with the picture Toshiba Recovery and recovery disc. There is option of Windows.

    If I have the right of you you want to create DVDs that you can use to clean the OS recovery installation of recovery. How it can be done is described in the document s user manuals.

    Anyway, recovery media can be created using preinstalled Toshiba Recovery disk creator tool.

    Check it out please
    By the way: has your laptop at the moment factory settings?

  • Satellite L300. Observation on the issues cover the recovery of Vista on a new HARD drive

    Hi all

    I need to reinstall Vista (on a Toshiba Satellite L300) runs the "recovery disc" created by Toshiba disc creator before recovery and using a disc of "nine" (Toshiba MK2035GSS, 200 GB).

    Issues related to the:

    (1) I have to partition and format the new drive before starting with recovery disks / DVD (s).
    or which will be done through the recovery process?

    (2) what is the reason for which the current disc is divided into two size equal C: and D: partitions, while
    D: partition seems to be reservered for the system, but only 5 GB are used?

    (3) what is the purpose of the partition 3. ("inactive") with about 1.5 GB of space?

    Thanks in advance for your support and help!

    Whalter

    > 1) I have to partition and format the new drive before starting with recovery disks / DVD (s).
    or which will be done through the recovery process?
    No, because the HARD disk should be formatted during the recovery process.

    (> 2) what is the reason for which the current disc is divided into two size equal partitions C: and D:, while
    D: partition seems to be reservered for the system, but only 5 GB are used?
    On the D partition, you can find the files and folder from HARD drive recovery. HARD disk recovery allows you to recover the laptop HARD drive and in this case, you don't need the recovery disc

    (> 3) what is the purpose of the partition 3. ("inactive") with about 1.5 GB of space?
    It is a Vista partition and is necessary for the backup files. Vista is able to repair the operating system if something bad is going to do this the necessary files that are stored on this partition.

  • Satellite L350D-21 problems using new HARD drive recovery recovery disks

    Hello

    I have laptop SATELLITE L350D-212 with windows 7 Home premium OA.
    He started to complain that there is something wrong with the hard drive so I went and bought another hard drive of the same size.

    I created the recovery disk when the computer was purchased and have backup of all the data in an external hard drive.

    After I changed the new hard drive to the laptop and tried to boot from the recovery disc, nothing happens eventhoug I can see it seems to be all Ok with the disc.

    Any ideas on how to get to run to the new hard drive recovery?

    I have the old hard drive attached as external drive via the USB port, but cannot boot from that too. It just stops at a certain point and told to stop.

    Hello

    Usually, the recovery disk must format the new HARD drive but I recommend you to join the new HARD drive as an external device to another computer and format the new HARD drive before trying to recover the laptop.

    Once the HARD drive has been formatted, connect it to the L350D and boot from the recovery disc

    Good luck

  • l hp dv6-6179-er: recovery on a new hard drive

    Hello world!

    I had the problem with my laptop, it is impossible to re - install windows from the recovery DVD, because the hard drive is broken. Is that going to be a problem to set the new hard drive and install the operating system? Is that there should be some error messages or something?

    shakog wrote:

    Hello world!

    I had the problem with my laptop, it is impossible to re - install windows from the recovery DVD, because the hard drive is broken. Is that going to be a problem to set the new hard drive and install the operating system? Is that there should be some error messages or something?

    The recovery disks work on a new hard drive, if they do not post back with the error message.

  • With the help of recovery on the new hard drive disks

    Hello

    I have an old t160.uk of Pavilion.  The hard disk starts to sound a bit grumpy.  I have a spare I want to replace it with.  Can I create recovery discs using the partition, and then replace the hard drive and reinstall windows xp on the new drive? or the recovery disks only works on the original hard drive?

    See you soon,.

    Hirroshi wrote: what determines if the new hard drive will be compatible with the recovery disk?  Could I connect the new hard drive in another Bay and try to use the recovery disk, before removing my old hard drive?

    Hello Hirroshi, it seems that drives hard very little HP only work in an HP computer, or so I said. I think it has to do with some code that HP puts in the Master Boot Record, but that's just a guess. I read on the Forum that this is the case.

    I suggest that you delete the partition on the replacement hard drive, and then create a new partition and format the hard drive. You should be able to use the recovery disk, if they are not damaged and that you have a valid burn.

    You can try to install the replacement hard drive in the system you propose, and it can work very well. It's certainly worth a try.

    Here is a link that shows how to perform a recovery facility when a hard drive is replaced.

  • Blue screen error: 0x0000001a when using system to restore with new hard drive disk

    original title: blue screen error when you use the system disk to restore with new hard drive

    I bought a new hard drive to my computer because the old one gave me a bunch of error messages on screen blues. I installed in the tower and tried to use my restore and system recovery disks that the manufacturer has given me, the process has got to the last disk then asked for the system once again restore disc, and then began to load the last steps and went to blue screen error. I don't know what to do, I mean it's a whole new drive hard, so where could the error come, theres nothing on the hard drive because I have not yet used really, yet. Help, please

    I have finally fixed the problem myself. The problem was that one of the sticks three memory was bad and the only way I could test this error. I took two sticks a left, used disks I had and was able to restore my computer, then I put a stick, turned on the computer, had no errors so I let him, so I put the last stick in and com immediately on, I had the Disconnections: memory management and that's when I knew that the last stick of memory was bad I took it back and now my computer works well and I can't buy more memory for not too. So if someone gets this BOSD error on memory, I'd say 8/10 computers have bad memory (not a number). If youcannot run the tool of diagnosis of memory like me then I would suggest to do what I did with the trial and error, it was the only way to understand the problem. Thanks for your help

  • No boot disk found during the installation of windows 7 in the new hard drive by using the original recovery disk

    Hello

    My laptop is HP - Pavilion dv6 2165-tx. My old hard drive damaged and so bought a new one.

    New hard drive works fine. (He went from main hard drive test)

    Now, to install the operating system, when I insert the recovery disc in my CD, I get the error message-"no boot device press a key after the insterting startup disk."

    How can I go about this now?

    Thank you for your contributions.

    I've installed windows 7 using my recovery disk. Problem is that my objective optical drive was not clean, which resulted in the error.

  • Blue Screen: Error Code C0000218(Registry File Failure) I have NO recovery disk, boot disk, etc. What can I do?

    I have a desktop HP that I installed a new hard drive on Windows XP Home Edition Service Pack 3. He has been working very well. But, the other day, I took out my DVD ROM and try it switched with different DVD - ROM, and when I restarted my computer, I got the "blue screen error Code: C0000218 (registry file failure)." The registry cannot load the HIVE (file). \System ROOT-SYSTEM 32-CONFIG-SOFTWARE or its log or alternate. It is damaged, missing, or not accessible in writing. "So, back to my main issue, I guess. How can I fiw it without any sort of disk recovery or boot disk etc... I know I could probably go buy some sort of recovery software, but can't afford it right now. Can someone help me, please?

    You have all the Norton/Symantec products installed and if so, do you know which ones and versions?

    You start with a chkdsk/r from the XP Recovery Console.

    Here's how:

    If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

    This is not the same as recovery disks that may have come to a store to purchase the system.

    You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

    The ISO bootable image file you need to download is called:

    xp_rec_con. ISO

    Download the ISO from here:

    http://www.mediafire.com/?ueyyzfymmig

    Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

    http://www.ImgBurn.com/

    Here are some instructions for ImgBurn:

    http://Forum.ImgBurn.com/index.php?showtopic=61

    It would be a good idea to test your bootable CD on a computer running.

    You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

    When you start on the CD, follow the instructions:

    Press any key to boot from CD...

    Installing Windows... going to pronounce.

    Press 'R' to enter the Recovery Console.

    Select the installation that you want to access (usually 1: C:\WINDOWS)

    You may be asked to enter the password (usually empty).

    You should be in the folder C:\WINDOWS.  It's the same as the

    C:\Windows folder that you see in Solution Explorer.

    The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

    For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

    A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

    In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

    Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

    Assuming your boot drive is C, run the following command:

    CHKDSK C: /r

    Let chkdsk finish to correct the problems, he could find.

    It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

    You must run chkdsk/r again until it finds no error to correct.

    Remove the CD, and then type "exit" to exit the RC and restart the computer.

    You have not to set the BIOS to boot the disk HARD since the CD won't be.

Maybe you are looking for