HP Pavilion p6-2069sc: computer hangs during the HP splash screen

Similar Questions

• HP Pavilion 23: computer hangs during the boot process

  Computer updates been made 2 days ago and has frozen black screen. Now does not start at the top. Starts the process and then freezes. He did start once yesterday and was going well for a few hours, then got a message saying computer had a problem.

  Error message:

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED (atikmdag.sys)

  Now back to not start upward again, hangs with the HP logo on the screen.

  Hi there @ldgie25.

  That the Forums are with you!  I understand that, after a few updates, your computer does not start correctly and freezes on the HP logo.   I'm happy to help you with this.

  Since it was started once, but then had a blue error screen, I suggest using the computers HP - use Microsoft System Restore (Windows, 10, 8).   Follow the instructions in the section «restore your computer when Windows is unable to boot normally»  See if it will start normally after the restoration. If yes then you probably want to prevent the offending update to install again.

  Please see the following for how to do this:

  How to temporarily prevent an update for driver reinstallation of Windows 10 - support.microsoft.com

  How to uninstall and updates to block and drivers on Windows 10 - howtogeek.com

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• Computer hangs during the transfer of 16 jpeg files.

  Recently, I replaced my Toshiba Satellite M40 PATA hard drive and reinstalled Windows XP SP3.  Subsequently, I find transfer more than 16 jpeg files (approx. 1 MB each) at the same time causes the computer freezes.  I have to shut down the computer and restart and sometimes the computer is 'always' Hung/frozen after restarting Windows (mouse move no keys, ctrl + alt + delete work does produce no action) which necessitated my stop down and restart the computer again.

  This problem occurs during various methods of transfer-to transfer pictures from my card SD using the scanner and camera or Nikon transfer software, trying to copy and paste pictures from the SD in an empty folder, and the problem occurs even when I try to spend more than 16 images from a folder in another.  I tried to transfer images from a folder with the computer in safe mode and the problem occurs when I try to transfer a little more than 16 images at once.  (my SD card, has about 60 images on that.)  There is no error message or any other message - the computer simply crashes.

  I did not have this problem before reinstalling XP.  There seems to be no limit to the size of the transfer that I could perform. I can't wait to find out how I can remedy this problem.  I am familiar with writing code, check the registry, etc, but I'm good enough following the simple procedures.  Thank you for your help.

  Original title: file transfer causes XP to hang, no error message

  Hi RobertMorouney,

  Thanks for posting in the Microsoft Community.

  In addition, how are you doing today?

  You have a problem with the computer hung on the transfer of files on Windows XP. This can be very frustrating for you, and I appreciate the efforts you have put in. Let us work together as a team and try to get this fixed number.

  Method 1-

  Step 1-

  Trying to transfer files in Mode without failure.

  Check out the link-

  To start the computer in safe mode

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Note: Make sure that you get the computer back to Normal Mode after performing all the troubleshooting steps.

  Proceed to step 2, if the problem does not occur in Mode without failure.

  Step 2-

  I recommend you perform the clean boot.

  Placing the computer in a boot minimum state helps determine if third-party applications or startup items are causing the problem. You must perform the steps in the article-

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: Make sure that get you the computer to a Normal startup after performing all the troubleshooting steps.

  Method 2-

  I wish that you run a Chkdsk command on the computer.

  Check out the link-

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265#Method1

  Note: The Chkdsk command will try to fix bad sectors on the hard drive. All the data on these sectors may be lost. The computer could go to a State no boot as well. Proceed at your own risk.

  We know if you need help. We will be happy to help you. We, at tender Microsoft to excellence.

  Thank you.

• The computer hangs during the analysis of Microsoft Security Essentials. Error checking: 0x0000007f

  Hello.

  My computer - windows 7 x 64 SP1 - is now fallen down several times all by performing a full scan of the system with Microsoft Security Essentials. This is the last event:

  Log name: System

  Source: Microsoft-Windows-WER-SystemErrorReporting
  Date: 28/02/2016 13:20:17
  Event ID: 1001
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer: GAMUT
  Description:
  The computer was restarted after a bugcheck.  The bugcheck was: 0x0000007a (0xffffffffc0000185, 0x000000010495a880, 0xfffff6fc500110e8, 0xfffff8a00221da3c). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 022816-17986-01.
  The event XML:
  
   
     
      1001
      0
      2
      0
      0
      0 x 80000000000000
     
      636121
     
     
      System
      RANGE
     
   
   
      0x0000007A (0xffffffffc0000185, 0x000000010495a880, 0xfffff6fc500110e8, 0xfffff8a00221da3c)
      C:\Windows\MEMORY. DMP
      022816-17986-01
   
  

  You can access the minidump here: https://www.dropbox.com/s/shogzx1tvdqh904/022816-17986-01.dmp?dl=0

  Can you help me? I don't know how to parse this file to understand what the problem is.

  Thank you!

  92 KB in bad sectors.

  You should check this number against the future reports. It will not reduce, but if it increases, you need to back up on external media and replace the disk.

  Cleaning of unused 161 entries index $SII of file 0x9.

  Cleaning of unused 161 entries index $SDH of file 0x9.

  Cleaning of 161 unused security descriptors.

  It is a problem less than bad sectors. If you get these errors, you must test the drive using the drive manufacturers test utility.

  Model Hitachi HTS543232A7A384 ATA Device

  IBM - Hitachi Drive Fitness Test 4.16

  http://www.MajorGeeks.com/files/details/ibm_hitachi_drive_fitness_test.html

• My computer hangs at the Windows loading screen OR blue screen comes up saying I need to install the hardware.

  Hi, I recently got a computer and I just realized that whenever I turn it on after a long period of time (eteindre turn off during the night, turn it on morning) my computer freezes at windows startup screen. Sometimes a blue error screen appears and after reading it, I would say that a material is not installed correctly. After graduating with my computer, I am sure that I have installed the latest updates, but im not sure what is causing this problem.

  Would be very happy to help!

  Thanks a bunch! : D

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• The computer hangs during the communication via a serial port

  I developed a code in LabVIEW 2011 to connect with the XY stage. It's actually two steps mounted perpendicularly. The installer of the system is that a (made by the same manufacturer as the stadium) gamepad is connected to the USB port on the computer if a USB to Serial converter. A step is daisy chanied to the controller and the other stage Garland at the first stage.

  To our application had to continually check the status and position of the steps X and Y. Because the joystick also returns responses when a request is sent to all devices, I need to send applications individually; for example. one request per order per device, making it a total of 4 orders. It takes care of the error returned by the controller. The problem, however, is that after a while the freezing of the program or the computer stops and restarts. It is located about 13 minutes (on average) after the start of the program. It also happens even when no command is sent to the devices. I put 50 ms delay before each send two commands (position and status) by device. Basically, the application waits for 50ms before sending two commands for X stage and the receipt of the response and when everything is done with X stage, he expects another 50 ms to do the same for step Y. Should this procedure goes on until the application is stopped. But as I said, there is a problem. Now, I guess the problem is that serial port buffer overflows. He chose to increase the delay time, but if it works to solve the problem, then I have no choice!

  I would appreciate any thoughts and comments!

  After a lot of time to experiment, I am convinced that the issue was with adapter Profilic.

• Computer hangs during the installation of updates (I have to install 64)

  What should I do when I cannot yet download or update anything without my computer freeze or lock up on me.

  Hi floridahmbdy,

  Check if an error message or error code listed in the event viewer, you can check the link below:http://windows.microsoft.com/en-us/windows7/What-information-appears-in-event-logs-Event-Viewer

  Try the methods below:

  1. start the computer to boot and check if you are able to install the update to Windows. Link below will help you to start the computer in clean boot:http://support.microsoft.com/kb/929135

  Make sure that you reset the computer in normal mode in step 7.

  2. you can also try the steps from the link below: the problems with the installation of the updates:http://windows.microsoft.com/en-us/windows7/Troubleshoot-problems-with-installing-updates

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer hangs during the update of Windows 8

  My laptop recently posted a message saying that he would automatically restart in 15 minutes to install a Windows Update.  After 15 minutes, it restarts and a screen will appear that says "Configuring Windows updates.  Do not turn off your computer. "He started to install, then stalled to the point 13%.  I rebooted several times, and it keeps the timing at this point.  I can't go past this screen for something else, so I have no use of the computer right now.  Y at - it a fix for this problem?  Thank you.

  Hi Rebannle,

  What is the brand and model of your computer?

  This problem may be caused for the following reasons:

  Conflicts of hardware/software.

  System files are corrupt.

  You can see the steps from the following thread that was answered by MikeSimmonsUK on November 7, 2012, that will help us solve the problem.

  Windows 8 updates stuck at 13%. (NOTE: laptop HP - audio drivers)

  If the problem persists, you can also see the steps in the following Microsoft article: Windows Update crashes when installing updates in Windows 8, Windows 7, or Windows Vista

  Notes:

  When you perform the System Restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  When running at Refresh: the applications that came with your PC or you installed on Windows Store will be reinstalled, but all the apps you have installed other Web sites and DVD is deleted. Windows puts a list of applications on your desktop after you refresh your PC.

  Keep us informed on the status of the issue.

• When install Vista Home Premium computer hangs on the language selection screen. No visible cursor, the keyboard and the mouse does not.

  Hi, when I try to install vista that Home Premium 32 bits on the computer of my son, through the installation of loading files with the gray bar at the bottom, then goes to the screen language selection, at this stage, I can not select anything using the keyboard or the mouse. There is no cursor visible. Keyboard and mouse both work fine in the bios and on other machines. Have used other keyboards and mice on the machine in question, but that makes no difference. Tried another copy of vista, no difference. Tested on Windows 7 install and everything works fine!

  Very confused, thinking that it must be a driver problem, but how about him? Any help is appreciated!

  Hi Rickydg,

  Thanks for posting. Please contact ASUS and see if there is a BIOS update available for your system. Update the BIOS and then try to install again.

  I hope this helps! Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Satellite Pro L300-1FN does not start - hang at the BIOS splash screen

  My Satellite Pro L300-1FN refuses to start. When turned on the laptop displays the home screen toshiba/insyde H20 BIOS and the message "press F2 go to the Setup utility, F12 to go to the start menu" and flashes the light access to the hard drive, but don't try to continue loading. I left the bios at the start screen, but it doesn't do anything for long hours on a power supply or is running the battery flat while on battery.

  Is there a way to re - put the BIOS on this unit? If it's a desktop unit I would remove the CMOS battery to force a reset of the BIOS but that's impossible on a laptop. The hard drive is fine because I have it plugged into another system to remove valuable data.

  Hello

  What happens if you press F2 when starting the laptop to the top?
  You can access the BIOS?
  If so, access the BIOS and set its default value. I think you need to press F9 or F10 to get default parameters, but this will be mentioned at the bottom of the page of the BIOS.

  Check it!

• HP HM-219: laptop starts but hangs at the Compac logo screen

  Laptop starts but hangs at the Compac logo screen. It is not even make to the Windows startup screen. I have to stop it, remove the battery, reinsert the battery & it starts perfectly. This should be done whenever I want to use. When I do this it still takes a while to fully fill the start up & get online. For months, it takes a long time to shut down when Im done with it. I ran the disk check, but it stops nearly 80 percent by the 4th scan process. I have Windows 7 Home Edition

  Hi there @akanyr,

  Thank you for joining the Forums HP's Support and welcome! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support. I wanted to join you and help! I understand that your notebook is suspended to the Logo of Compaq screen.

  If the computer hangs at the Compaq logo screen, try to clean the vents from the computer to the air and then restarting the laptop.

  Please note , remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

  Have you tried a hard reset?

  Have you tried to Test for hardware failures?

  Are - that you receive error messages or error codes?

  Follow these steps to remove and reinsert the memory modules for troubleshooting:

• [SOLVED] Windows 7 hangs during the "you want to allow this program to make changes to your computer.

  I was recently on my computer and running windows 7 with happiness and problem free, until I downloaded a file from the internet. When I opened it, windows asked me if I want to allow this program allow changes. However, there is the rub. When I click on 'Yes', the message will disappear, but the computer hangs at the screen has gone even a light, tinted gray, with all of the programs that are still running in the background. It freezes for about 2 minutes and then decides to return to normal, free for me to return to work and navigation. However, the program that I have originally intended to be performed by him to make changes didn't work at all. Confused, I ran over and over again, but with very little success, and the problem continued to appear. I tried to launch a clean boot, but that doesn't help more. Can someone help me please? Thanks :)

  Thank you for the support, but I solved the problem.

  I did a system restore, and it seems that a microsoft critical update was the culprit of all this? In any case, everything seems to work now and thanks again for all the support and help, I appreciate it a lot :)

• I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  Hello

  1. at what stage of the installation, the computer crashes?

  2. what operating system was installed on your computer prior to this?

  If you have the similar problem as mentioned in these links, you can follow these links and check if the problem persists:

  Windows XP Setup stops responding (hangs) during the "Preparing Installation" phase

  Windows XP does not meet the Message "Setup starts Windows XP"

  Hope the helps of information.

• Pavilion h8 - 1070t: blocked on the HP splash screen, computer beep

  I just installed a PSU Corsair CX600 and an EVGA GeForce gt 740.

  When I start my PC, is rest on the start screen and beeps once, every ten seconds. After 3 beeps (30 seconds) my PC beeps again followed three quick beeps and the monitor stops receiving signal from the computer (I do not see the HP splash screen, no signal).

  What could be the problem?

  I think that your problem is that the video card is not compatible with your BIOS.  EVGA 700 series cards require UEFI in the motherboard instead of a standard BIOS.  I suggest you to contact EVGA Tech Support (1-888-880-3842) to see if they have a VBIOS update that will allow the card to work with your computer.  If they do not have an update that they can email it to you.  Tell them that someone of the HP Forums suggested that you call.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Windows hangs on the last blue screen and is unable to stop.

  During the shutdown process, after downloading updated successfully, the is Windows XP hangs on the last blue screen "shutdown of windows.  For now I just have to unplug it from the power supply to the stop card.  I run a maintenance program, but it does not solve this problem.

  Hi, Tinker,

  1. you receive messages or error codes?

  2 have. what maintenance program you tried running?

  Method 1:

  You can visit the computer manufacturer and try updating the chipset and video card drivers.

  How to manage devices in Windows XP

  Method 2:

  You can also check if the problem occurs in safe mode.

  To start the computer in safe mode

  A description of the options to start in Windows XP Mode

  You can also read the following article and check if it helps

  Advanced Troubleshooting for shutdown problems in Windows XP

  You can check in the event viewer to see if there are newspapers in events related to the issue.

  For more information, you can consult the following article:

  Procedure to view and manage event logs in Event Viewer in Windows XP