HP pavilion p6 2310: upgrade of the power supply

I was wondering if this diet will enter my pc hp pavilion p6 2310

http://www.NCIX.com/detail/EVGA-500W-80-plus-certified-5F-92643-1563.htm

Power supply I want

Hello

The standard ATX HP power measured 5.9 by 3.4 by 5.5.  As posted by your link shows a good fit.

An examination revealed a problem of quality control but the other customers looked good.

Tags: HP Desktops

Similar Questions

  • The MOBO will support an upgrade of the power supply

    I want to buy an ASUS GeForce GT 430, but it requires a power of 300w.  The motherboard in the CQ5320F will support the upgrade of the power supply without frying the MOBO?  The original PSU was a 250w.

    Thank you.

    Bill

    My HPm8100e has the same card, but it is rev is Narra2. I installed an XFX HD5670 and a Rosewill 530W.

  • The upgrade of the power supply for HP Pavilion M7570N

    The reason I'm on this forum is when I called hp support and gave me a stupid answer of not being able to change the PSU because of software...

    Well well, the reason why I'm spending power supply is because I bought a new video card and he needs about 500watts and my current power supply is 300watts and I was wondering if I can change it. The video card I bought requires also [2] PCI-E 6-pin

    Video card: http://www.newegg.com/Product/Product.aspx?Item=N82E16814150325

    Current PSU: HP manufacturer: 5188-2625

    New power supply: http://www.newegg.com/Product/Product.aspx?Item=N82E16817159085

    I don't know if the size can fit the case m7570n (the slot of the psu) and I don't know if she has enough connectors for everything that is inside the computer

    * Note * I have not changed the computer, I haven't added or whatever it is taken so the connectors, there will be the same amount connected

    Message edited by TheNoob on 2009-02-02 19:01

    It's a high-end desktop PC.  No doubt he will come with an ATX PSU with 5VDC, 12VDC and 3.3Vdc output rails.  I'm not familiar with the Interior of your PC, so I'll give you two General configurations of PSU layout.

    1. design intermediary such as PC Power & Cooling with one or two 80 mm fans to expel air through the PSU.

    http://www.Newegg.com/product/product.aspx?item=N82E16817341011

    2 down-draft design as Cosair 450VX with a 120 mm or more huge blowing fan case in the heat sink and the motherboard of the PSU.

    http://www.Newegg.com/product/product.aspx?item=N82E16817139003

    If the power supply is at the top, back or side of the PC, then a power supply down-project will do a better job to remove heat from the PC.  If the power supply is in the middle of the PC, then go with an intermediate design.  This design will generate more noise at higher load, since the smallest fan should turn more quickly to transport the same amount of air in a 150 mm or 120 mm fan.

    Looking for a nominal 80% efficiency POWER supply.  Detachable power cable is a bonus to maximize the air flow inside the PC.  Make sure the power supply is delivered with the right type of power connector to drive you GPU.  All modern units of quality with 20 + 4 and 4 + 4 key cards.  If you do not plan to run graphic dual with a high range GPU, so it doesn't matter what quality 80 watter 380 power SUPPLY Antec, Corsair, Enermax and Seasonic PSU will be enough.  You will need to back up POWER supply to 450-550W, if you run two graphics cards high-end.

    A good 450W PSU is a good compromise because it is more effective when the PC is idle and has enough power to run two GPUS.  If you want to save $ on electricity, then get a smaller power supply (range 300-350W) because these units reach the level of efficiency of 80% around release of 65 to 70 watts.

  • HP Envy 750-116: can anyone recommend an upgrade of the power supply for HP Envy 750-116?

    I have a HP Envy Office 750-116 and need to replace the power supply 300W with an upgrade to a more powerful.

    I was look at is CORSAIR CXM CX550M 550W 80 PLUS BRONZE or the EVGA SuperNOVA 650 G2 80 series. I have kniow that they are all two excellent PSU.

    My concern is with the connector that the 750-116 uses to the optical drive. Looks like the kind of connector you see go to a laptop, DVD player. (It of really small and is marked P5)  I have a spare part HP 460W PSU I could use, but it is not a connector that would work. So I hesitate to buy Corsair or the EVGA without knowing if I'll be able to plug into this weird DVD connector in the HP Envy.

    Someone out there has run into that and find an answer?

    Bill

    Optical drives are still a thing? Wow! Any ways OP. On these new machines. HP uses a slim with an owner drive

    Connector for it. You won't find it on the other PSU. You will have to abandon the drive if you replace the stock PSU.

  • The upgrade of the power supply.

    I recently bought a vido GTX580 and discovered after I got that my wimpy 250 watt power supply will not manage it. The card requires at least a power of 600W at 42 amps on the 12V rails. The card must also 8-pin and a 6 'PCI Express' connectors from the power supply. Could someone recommend a diet that works with my hp P6774Y desktop computer? Also, it is quite easy to replace?  Thank you!

    Thanks to all who responded!  I just got back from my local Best Buy store, and they had an 850 Watt Thermaltake 'Black Widow' food on sale for $100,00 and I bought. After reading the comment by wb2001 about the depth of power supply, I'm a little worried about that, but I don't know until what I opened the box (the physical dimensions are not printed on the box) and try to mount it. Wish me luck!  :-)

    Thanks again!

  • The upgrade of the power supply for a HP Pavilion 500-054

    Hey people,

    I'm changing the 500-054 flag so that it can play a few games, not a hardcore gamer, just want to be able to play the occasional game. I want to get a lower end external video card, but this requires a power supply greater than 300. I am looking for a new power supply for my computer, but I couldn't find one for the 500-074. Are the ones that will work for my computer or I am a hopeless case?

    Thank you

    A standard ATX power supply will work. Please look at the Corsair CX430, CX500, CX600, or their variations of modular cables for your needs.

    If you have any other questions, feel free to ask.

    Please click the White Star of KUDOS to show your appreciation

  • The upgrade of the power supply for Alienware R4

    I just bought a MSI r9 390 x upgrade my r9 270 came with the computer. I had a problem where as soon as I turn my graphics to the max the computer restarts. No blue no screen no error message just to the top restart as if someone plugged and unplugged the pc.

    I have this reduced to a problem of power supply as no overheating takes place. I think it is the J556T power supply provided with the original pc stock. I don't think that's the tension to keep the card will I think 18V POWER supply which im sure this card requires more volts 18 years to operate at high efficiency. If you think the same thing that I am I would like to improve my diet, the problem now is the case around the PSU doesn't let me with many options because it only having openings on the sides and PSU most now have fans in the top and bottom. What PSU suggest you.

    «How about we get your diet 1 work before to decide, it is not decent...» »...

    Tip: two cables grfx were J556T, each cable is rated @ 18amps, which makes the two tracks of 12V 18amp; you have to feed the card with every cable / each tubular structure for better performance. While each cable carries a 6pin & a jumper 6 + 2, don't let it fool you > he stlll reduced to be just a cable. Try the two cables: use one & only one connector type out of each cable...

    Tip: when the need for a "8pin", insert the primary 6pin & borrow the 2pin off the 2ndary rider

    -Aurora: How to run a card 375 watt... kind of... -

    -most Aurora owners who have the PSU 875 watt also have a cable that is not used in the floor case: use the...

    Here is a 375-watt + HD6990: note the grfx-RED & blu - ylw cables are deployed both 6990 has two rails 12v 18amp--> 18 x 2 = 36 x 12v = 432watts has a. Good looking<>

    To use only one cable (prim and jmpr) is to refuse access map to additional 216watts provided by cable #2. unlovely

    For these cards that need one (or two) 8pins, we do that again? --> Insert the primary 6pin, borrow the 2pin off the 2ndary rider & ask the rider on the side, unused <> kapisch?

    -the primary 6pins is the path of least resistance-

    By the way by the primary 6pins - & with the horsemen of 2ndary - the person above uses a less effective connection diagram; resistance built in the appendices of the rider:

    • because of her crimp mechanics inside the primary 6 p
    • due to the addition of 4inches of wire, it's the rider
    • because of her crimp mechanics inside the cavalier 6pin

    -do not 'put' the primary 6pin on the side (left), "throw" the rider to the side & borrow its 2 pin (right).

    Aurora in a solo card application, always use the primary 6pins (=

  • The upgrade of the power supply on a6345.sc

    Hello.

    I wonder if a standard ATX PSU will enter my a6345.sc? I really need for my GPU, and the block power.

    Kromgol wrote:

    Hello.

    I wonder if a standard ATX PSU will enter my a6345.sc? I really need for my GPU, and the block power.

    Yes. A standard ATX PSU will agree and will function properly. As you upgrade the video card (GPU), I suggest to install a large manufacturer of at least 500 watt POWER supply.

    I recommend the OCZ and Corsair PSU. Ensure that the specification of the PSU is EPS12V ATX12v V2.2 80 Plus Bronze certified.

    Here's the section of power supply at NewEgg.com

    Best regards
    ERICO.

  • Pavilion m9670ch Desktop: replacement of the power supply

    I replaced the original power supply with another more powerful (550W) earlier, I bought a new graphics card. This power is very strong, that's why I bought a new DARK PRO 10 power SUPPLY ATX 550W. Now, the computer does not start. When I press the power button, the fan starts momentarily and stops again. All cables are correctly installed. I reinstalled the old power supply (fort) again and everything works normally (except for the noisy fan). I contacted the manufacturer of the unit from the POWER of DARKNESS, but he referred me to HP, because they did not have a solution, but it may be a peculiarity of the motherboard. What can I do?

    Hello

    Return the Dark Power Pro and get a Corsair CX500, or CX600.

  • Pavilion p6000 series p6633w: upgrade of the power supply

    It also seems that the fan is on top of the PSU, so when installing, I need to done deal inside the Tower fan?

    It can be installed in any event.  However, the most common way is confronted in the case.

    Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

  • Upgrade the graphics card and the power supply on a Pavilion p6823w - compatibility?

    Hello, everyone! After purchasing my HP not too long ago, I decided that I wanted to get updates for it. I intend to turn it into a computer game later, but for now I start small.

    I'm still a little wet behind the ears when it comes to computer hardware, so I would greatly appreciate any input on my decisions for improvement - especially if my power supply and graphics card will adapt and be compatible or if the marks are bad.

    Graphics card:

    PowerColor Radeon HD 6850 1 GB

    http://www.Newegg.com/product/product.aspx?item=N82E16814131374

    POWER SUPPLY:

    Corsair 500W CX500

    http://www.Newegg.com/product/product.aspx?item=N82E16817139027

    Here is the specific computer I have, for reference:

    http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=es&CC=ve&TaskID=120&prodSeriesId=...

    Thanks in advance!

    Hello

    I don't foresee any problems with your choices.

    Relatives on the slot PCI-E x 16 must be vacant.  Examine the characteristics of the motherboard.

    These "how-to" HP articles should be useful.

    TIP: Unlock and slide the optical drive forward before you remove and install the power supply. This helps facilitate the removal and installation of the power supply, but it is not mandatory.

  • Need help/advice on the upgrading GFX and power supply for PC p6754y

    Hi, I want to upgrade my computer (Hp Pavilion P6000 Series, model n ° p6754y) so I can play new games such as Skyrim or Battlefield 3 on ultra. I don't know too much about computers, and it would be my first time upgrading mine. Here are the parts I have in mind.

    POWER SUPPLY

    http://www.Newegg.com/product/product.aspx?item=N82E16817341017

    GFX

    http://www.Newegg.com/product/product.aspx?item=N82E16814102908

    Please let me know if it works well with my computer or if you have other recommendations/tips instead.

    Thanks for the help

    Hello

    The power supply and the video card must be inserted.

    Try this link is your PC ready for BF3?

    Most PCs are not ready for BF3 and there is usually a faster video card and a bigger power supply.

  • Replacing the power supply on a HP Pavilion P6000

    Outputs video (DVI and VGA) were both released on my motherboard. Rather than go through the hassle of dealing with Microsoft if I had to replace the MB, I decided to install a MSI Geforce 210 graphics card and the existing PCI express slot. However, the existing power is rated at 250 watts and the new video card got a minimum rating of 300 watts. It seems to work, and I don't do any high-end graphics or game. My main uses of the PC are paying bill online, e-mail and a few online forums. Should I replace the power supply with a higher nominal? I have a Hiper Type R PSU which is estimated at 580 watts and was planning to replace it with the 250, but it looks like not her suits because it is deeper than the power installed about half an inch. The deeper power looks like it should stick on a half inch at the rear of the computer when it is against the stop before power in the case. I would like to have some advice on the use of the existing offer or be able to use my power Hiper 580.

    The HP Pavilion P6617C model, which is the number of product BT427AAR developed a standard ATX size power supply. Dimensions (as you know) are 5.9 "x 3.4" on the back and depth 5.5"in the case. The small metal latch/stop button to slide the power supply existing forwards (for removal). There really is no support.

    4 rear mounting screws fix the power supply of the Cabinet. Of concern would be the length, an added 0.7 ", as well as cables/connectors.  You can try the Hiper in the case, and if it fits, OK. Otherwise, I suggest a diet that actually matches the Rosewill 630W

  • Replace the power supply for a Pavilion a140n

    How to install a new power supply in a HP Pavilion a140n? Is there a step by step guide?

    Zz30fg, welcome to the forum.

    Is the model you list correct?  I can't find anywhere.

    Before you start, I suggest that you measure existing power supply unit (PSU) to make sure that the one you choose to insert in the space provided.

    The first thing you will do is turn off the computer.  Disconnect all devices that are connected, for example, keyboard, mouse, printer, etc.  Once done, remove the side cover of the case.  There are two or more screws on the back of the computer that you have to remove.  Then slide the side gently to the rear.  Put it somewhere safe.   Be sure to touch the metal inside of the case before touching any components.  This will eliminate static electricity (ESD).  Now you can disconnect the cables from the PSU.  This is where it gets a little tricky.  I normally take a picture of the connections and mark them as clearly as possible on the motherboard.  Believe me, you'll be much happier if you do.  Once this operation is complete, it is time to remove the (4) screws that hold the power supply in place.  Hold it with care.  If it falls it can damage other components.

    The new power supply will be marked with the appropriate connector cables.  At this point, it's just the opposite of what you were doing to uninstall the existing PSU.  Install the power supply into the case.  Do not overtighten the screws.  Make sure that the cables are inside the case.  Once in place, carefully connect all cables to the appropriate connectors.

    If you have any other questions, I will watch this thread for you help.

    If your problem is solved, please click "accept as a Solution.

  • Have HP Pavilion dv2500, won, t turn on. When you connect the power supply blinks blue.

    Have HP Pavilion laptop dv2500, p/n kn997ua #aba, does not illuminate. When you connect the power supply blinks blue.

    Now you can take the laptop at best buy or Wal-Mart and get them to plug a power cord. This will give you an idea if you need to buy a power cord or not.

    Again, you can always buy the power supply cord and if it does not return.

    THX

Maybe you are looking for

  • Re: Satellite Pro L870-172 keyboard Intermittent behavior

    I experience strange behavior with my keyboard mainly intermittent when using excel spreadheets where the screen zoom in and out, several cells are highlighted by trying to enter data, the data is copied to separate sheets & different characters are

  • How to restore Toshiba external HARD drive information system?

    I use macbook aluminum. When I insert my Toshiba Portable External Hard Drive 320 GB (ext. HDD 2.5 ") 3 on my laptop the time machine automatically ask me if I want to use the hard drive as backup. I accidentally said yes and allow him to erase all i

  • Control buttons do not work after the new installation OS on Equium A100-147

    After Installing Win XP manually, I am facing problem for the multimedia keys on the left side of the laptop work. I am able to access the first button to launch Internet Explorer and Windows Media Player but still keys Play/Stop / > /.< not="" worki

  • Storage of Information within the screw

    I have an interesting problem... I have a VI that controls a subsystem. It has about 80 entries, when he used the subsystem with these entries programs. Entries are not homogeneous, they are information configuration and each means something differen

  • How can I set a password on my PC

    Hello My PC is Vista and Firefox for about 3 years. I want to convert it to my exclusive use so I need to set a password before starting to prevent others to open my computer. And how can I make sure I'm the only Admin? Thank you