HP photosmart 7520: can this scanner duplex printer?

Similar Questions

• New HP Photosmart 7520 e-all-in-one printer from the box, removed the tape and cartridge access

  

  I have a new HP Photosmart 7520 e-all-in-one printer just out the box. I removed the tape and cartridge access door does not open more than 40 degrees. The figure represents about 80 degrees. I'm afraid to force it. I can't put new cartridges in the printer. Very frustrated trying to get help. It doesn't seem to be a phone number or Web site for direct assistance. HP has really gone down hill. Help!

  Hello

  Mine is about 45 degrees, sufficient space to install the ink cartridges.

  Kind regards.

• I can't automatically duplex print with my HP Photosmart C7280

  They only options I have is for manual, left or right edge.  In the past, I could choose to do duplex printing automatically.  the printer has a duplex magazine.   I tried several times to reinstall the drivers/software does not.

  I use Windows 7 Professional 32 bit.  I get no error message.  I have

  The duplexer must be set to "installed", as described in the Vista/Windows 7 Duplex Printing solutions to the problems here.

• Photosmart 5520 (but also others) duplex printing cleared at the bottom

  Very recently, I bought a Hp Photosmart 5520 and I found that sometimes the bottom of a page is cut off when printing double-sided. I looked in this forum and found that this problem is hardware related and can not be solved, but there are solutions. I did a few tests with my current setup and I want to share my discoveries, here for other users waiting for HP to add a FAQ for the photosmart 5520 entry. (but also for the 6520 and 7520, probably)

  The problem is clearly stated in a few messages, dating from September 2013 and Nov 2013, although it is not very easy to find

  http://h30434.www3.HP.com/T5/other-printing-questions/duplexing-discrepancy/m-p/2470573/highlight/tr...

  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/double-sided-printing-is-cut-off-short-Phot...

  Basically, the margin of the low printable area is 3mm side simple impression, while it is 15mm (at least!) for the first page, double-sided printing. This is due to the fact that the printer must keep the paper in the output roll after that that he finished printing the first page. It is therefore IMPOSSIBLE to duplex - print a document with text or graphics that extends beyond the margin of the lower 15 mm, unless the page size is reduced so that the effective bottom margin is 15 mm. On the other hand, if the document does not contain text or graphics beyond bottom margin of 15 mm it CAN be printed double-sided without reduction.

  IMHO, the problem is that the default behavior of the firmware of the printer, the drivers of operating system and/or applications do not always properly address this limitation leading to surprising or unsatisfactory results.

  To better understand the limits and behavior of the printer, I have carried out tests under the following conditions:

  (1) copy 2-sided vs 1-side in the printer display

  (2) Windows 7 applications: Word2010, Foxit PDF reader, Acrobat PDF reader

  (3) 4.3 android: Cloud Print and HP ePrint apps

  The firmware in the printer is MGP5CN1351AR (Sep 12, 2013)

  The windows version of printer drivers is 28.8 (October 30, 2012)

  For tests 2 and 3, I have prepared a document word of 2 pages with headers and footers located exactly at 15 mm of margin top and bottom of the page and I have produced a PDF with CutePDF (unfortunately this forum does not allow attachments, otherwise I would have attached it).

  The results were as follows

  (1) in 2-sided copy the last 15 mm on part and on the other copy of the output are empty, even if the text of the content entry page, while, in 1-sided copy only the last 3 mm are empty (resizing is turned off, of course)

  (2) double-sided printed of Word2010 gives a duplexer not resized when the printing preferences, advanced options, "Arrangement" is disabled. If it is set on, the output is reduced. Print PDF files is tricky: there are several different options in Foxit PDF and acrobat PDF. Auto-Centre and adjustment - on the page to print double-sided, but do not keep the right size in Foxit PDF reader; If preserve layout is off a significant part of the bottom of the page is not printed, apparently due to the fact that the margins are not properly managed by foxit PDF. Acrobat PDF instead, leave a good impression both sides preserve the page layout and scaling are disabled (obviously up to 15 mm).

  (3) android Cloud Print prints the word and pdf files WITHOUT a provision to 'preserve', this is why some clipping may occur; HP ePrint prints two word files and pdf reduced in size, as if "preserve layout" option has been set.

  In summary, I'll leave the "preserve layout" options always on in windows and I'll take a cut on the side of double-sided printing and I use hp eprint instead of cloudprint. If the correct size is important to a PDF file, it is best to experiment with Acrobat PDF (even if it is not a light program). iI would be expected at HP improved the behavior of the windows printer drivers to print a PDF file.

  I hope that this post may be useful to other people.

  You are right, that the effective page size is reduced because of the extra margins required to manage the document in automatic duplex mode.  From the rear is donated in the printer from the bottom and bottom printed in the top margin is also higher top for the back to the front.

  The checkbox 'Keep the page layout' is important for results appropriate, although it will reduce the effective print size.

  I've seen reports before of Foxit PDF printing problems, I avoid and use Adobe Reader.

• Photosmart 7520: Dialog box scanner Photosmart 7520 shortfall 8.1

  I can't scan using the supplied more. Right click on the printer in devices and Printers icon now appears four choices - all in remote preferences, set one, see what's printing, and customize. No scan options. Running exe HP offer just adds a printer or add new software. New software just offers the HP improvement program, the Bing bar, or make photo creations. Scanner options disappeared.

  Hello

  Please uninstall the software by going to control panel > programs and features > uninstall a program.

  Uninstall the HP Photosmart 7520 basic device drivers.

  Download and install the latest version of the software below, do not use the CD to reinstall the software:

  http://ftp.HP.com/pub/softlib/software12/COL43773/MP-108670-3/PS7520_1315-1.exe

  Once you have finished, click on the Start button () in the lower left corner of the screen, click Find, type 7520 and open the HP Photosmart 7520 software.

  Click on scan a document or photo to launch the HP scanning software.

  Please let me knoiw results.

  Shlomi

• Photosmart 7520 - can not scan to computer directly

  I have a 7520 new.  And using a Mac OSX 10.8.5.  The printer works perfectly.  When I try to scan, I get a message that there is no commumication with the printer.  I arrived at the printer utilities and the attempt to activate the scan and get the same message.  However, if I go to the web operation shipped it see communication, and if I use the operation of analysis on the web server it scans correctly.  How can I get rid of having to go to the web to analyze and do it in my printer?

  Hello

  I'm sorry to hear you can't scan with your Photosmart 7520 and your Mac OS X 10.8.5. I would like to help. I have studied this problem for you and have found a troubleshooting guide that I'll post for you below to follow.

  I hope this helps!

  Problems of communication during the analysis

  Kind regards

• Photosmart 7520 e all-in-one printer not turn on, green transformer upward and then turns off.

  7520 E Photosmart all-in-one printer not turn, transformer green light comes on then off again once, unplug the left and I tried once again even.

  nothing is dead.

  Hi woldtopper,

  I understand your Photosmart 7520 is not turning on and will remain lit. Please follow the steps in troubleshooting in the following document; The HP printer will not be running or to respond when the power button is pressed.

  If the problem persists, I recommend calling HP and let know, the issue and the steps you have already performed. It may be able to let them know that you completed all the steps in the HP document #c01321436.

  If you are in the Canada, U.S. dial 800-474-6836 or you can Contact HP worldwide.

  HP printers usually have a warranty of 1 year from the date of purchase, you can check the warranty using the following if you wish; guarantee cheque.

  I hope this helps.

• Photosmart 7520, impossible to reinstall the printer after removing software

  Name of the product and operating system: Photosmart 7520, Windows 7 32 bit.

  Description of the problem:

  I tried a lot already if the description is quite long, bear with me here.

  At the beginning everything worked well. After a few months, the printer was not capable of scanning more computers in the network. He could identify them, he was not able to transfer the scanned document. Printing from computers was still possible. I did first network tests, even reset network to factory settings, but everything was fine. Try to solve this problem, I ran HP print and scan the doctor, the program gave me a twain scan error and was not able to fix it. Because it was not able to fix it. I uninstalled the computer HP printing software, reinstall the printer completely and try if it works. Digitization (magicly) now works on my other computer, but I can not reinstall the printer on the computer where I uninstalled the software, because it is impossible to find the printer on the network. I also tried to connect the USB printer, without a bit of luck. I think it's a driver problem, because the computer seems to have many 7520 drivers broken out there. I hope someone has a way to help me, because I don't know what to do anymore...

  

  Try to run Malwarebytes to see if your PC has installed any villains

• LaserJet CP2025: My computer did an update of Windows 10 and now I can't do duplex printing CP2025

  Microsoft today pushed through an update Windows 10. Now I can't do a duplexing printer laserjet CP2025. Any ideas? The drivers that I download do not seem to help.

  Hello
  Make sure that the automatic duplex printing option is selected:

  Enter the control panel > devices and printers.
  Right-click the printer icon, and then click printer properties.
  Click the device settings tab.
  As installed in Duplex Automatic Two-Sided accessory and then click OK to save the change.

  Now try printing again.

  Kind regards
  Shlomi

• How can I activate duplex printing apps?

  We recently acquired an Officejet Pro 8600 and so far are happy with its speed and quiet.

  Maybe it's just the one app (Scheduler Menu 7 days), but when I got a print there not print duplex automatically. I looked through the printer setup and preferences on the touch interface, but nothing was found for force applications print using duplex.

  Is this one by setting the app or is there a way for the 8600 force duplex printing applications? I'd hate to empty a USA Today to find that it was on single-sided only.

  Thank you

  mikehd

  Found my answer on a previous post. It is of course being implemented on a basis by app, the menu 7 days app currently does not support duplex printing.

• How can I disable duplex printing in Adobe?

  Whenever I have something from Adobe Acrobat Reader, print it prints double-sided.  How to disable this option?  I feel like I've looked everywhere!

  Hello

  Please visit the following link once.

  How can I turn off AUTOMATIC double-sided printing? Every day it automatically turns this back? (Print production)

  Concerning

  Sukrit diallo

• Photosmart 5515 - how to set duplex printing? and duplexing of the M/s word?

  I recently bought a Photosmart 5515 for my Mac.

  1. I want to set default printing as front / double-sided and need help because I do not see this as an option.

  2. I am using Microsoft word and can not select two-sided printing option - please can someone advise

  I trieds many forums, and it's a common problem. Any advice would be welcome, because I bought this to help reduce the amount of paper I use.

  Thank you

  Hello

  Follow the steps below to perform pprinting Duplex of Office for Mac:

  1. On the file menu, select print. The print window is displayed.
     NOTE: The print window might be minimized. Click the blue triangle next to the product model (Mac OS X 10.6) or the view details button (10.7) see all available parameters. To select the connection type click the lowest selection box - Copies & Pages.
  2. Select from the drop-down.
  3. Set the duplex option as liaison Long Edge (Portrait) or binding Long Edge (landscape).

  You can save the settings for later use by clicking predefined settings > Save settings as a preset.

  Kind regards

  Shlomi

• Photosmart 7520: After 5 minutes is printer is no longer available on wifi

  After 5 minutes is printer is no longer available on wifi. This means that after 5 minutes, the printer is always connected to the wifi but when I try to print from an iPhone or I touch no printer is online.
  The printer go back online if I disable a turn on the printer again.
  I tried the common wifi fix on this forum without solution.
  Any help?

  Finally, I solved with a change of router.
  I bought a new router a TP link wr841N instead of the Belkin and now everything is perfect with a solid connection.

• Photosmart 7520 e: quality test ok, print faded, print new ink cartridges. In / uninstalled Adobe R DC

  My printer went from fine print only for color printing and now only copying glass screen.  The print quality test is very good, all the colors, including black are very good.  All new ink cartridges.  Recently installed Adobe Reader DC and then removed. Mini Mac OS X v10.9.

  I have to uninstall and reinstall the printer software?

  It should be written on the old software. When you are rested and ready to tackle the issue once again let me know.

• HP photosmart 7520: printer does not print when lite blue flashes

  I just noticed recently that my printer does not print blue wifi lite flashes when the icon of the printer on my computer says printer not connected, but it's all about.  Ive tried unpluging the router, then the printer and restart the computer that gets everything back up and working, but after a while it goes back to blinking and does not print what is wrong.

  Hello

  Asuming the printer is connected wireless, a flashing blue light indicates a lost wifi connection, the pritner is disconnected from your network at the time and so it will not be printed.

  I suggest to place the printer near the router, but not less than 2 metres. too far can cause the connection to become less stable, but also too close distance due to dead radio signal problems.

  Try putting 2-3 meters to test, make sure you there are no metal objects in the path between the pritner and router (which can affect the wireless radio).

  Other that those try after the following steps to solve this kind of problem:

  http://support.HP.com/us-en/product/HP-Photosmart-7520-e-all-in-one-printer/5199461/model/5199462/document/c03381908

  Plwase informed me of a difference

  Shlomi