HP Photosmart D110a: unable to connect to my my router D110a wireless Comcast

Similar Questions

• Unable to connect to the broadband router by wireless or cable ethernet hub is active as my xbox living works through it will need to activate the ethernet port and wireless function bt someway

  may need to download drivers

  It comes with Vista, upgrade install and activate Forum.

  http://social.answers.Microsoft.com/forums/en-us/vistanetworking/threads

  "Connect to a network, mail and the Internet."

  They will help you with your question in the Vista Networking Forum above.

  See you soon.

  Mick Murphy - Microsoft partner

• HP Photosmart 7520 unable to connect to Web Services

  It's used to work. Now when I try to scan to e-mail, I get all the way to where I choose it as a Document and then I get the message "unable to connect to web services. I printed out the results of the wireless network Test and everything looks great. Also, the Configuration of the network page is superb. My name network, says it is connected to the Internet. I was able to download the updates. IP address looks right.

  I have downloaded and run printing HP and doctor Scan and it crashed.

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: HPDiagnosticCoreUI.exe
  Application version: 3.1.0.25
  Application timestamp: 50fd3a60
  Fault Module name: dlbxtwds.ds
  Fault Module Version: 3.107.0.0
  Timestamp of Module error: 45df4cd1
  Exception code: c0000005
  Exception offset: 00004da2
  OS version: 6.1.7601.2.1.0.768.3
  Locale ID: 1033
  Additional information 1: 0a9e
  More information 2: 0a9e372d3b4ad19135b953a78882e789
  Additional information 3: 0a9e
  Additional information 4: 0a9e372d3b4ad19135b953a78882e789

  @shoikh

  I understand that your printer is not connected to the web services.  . I would first disconnect the router and the printer for about 1 minute.  I would plug the router first then the printer. I would then try to enable web services. If not successful, and you get the same error message. I'd follow these steps.

  1 obtain the IP address of your printer

  a. This can be done by pressing the icon on the printer wireless.

  2. Enter the printer's IP address in a browser.

  3. Select the tab network at the top of the page.

  4. on the left, select network.

  5. Select Network (IP) address

  6. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  7. Select apply you could get a fair warning select OK.

• HP photosmart 7520: HP photosmart 7520 unable to connect to web services

  I am also having this problem. I tried the solutions above. Can you also send the solution for me?

  drzman1

  Welcome to the Community Forum of HP.

  I don't know that to which you are referring - he could be the following:

  By PrintDoc Web services

  PhotoSmart 7520 does not connect to "Web Services"

  You can take a look at the suggestions already provided - they are likely valid for your situation.

  I can also offer you the following:

  Reset Web Services in ePrint printer

  • A method essentially provides the procedure that you find in PrintDocof wire,
  • Two method explains one more 'standard' reset Web Services approach.

  ============================================

  If you are in the USA or the Canada, you can call using Cloud Services.  I suspect that they can help during normal hours, but you can certainly call anytime and see if help is available:

  When to call HP Cloud Services and when to call HP Tech Support

  Click on the thumbs-up Kudos to say thank you!

  And... Click on accept as Solution when my answer provides a fix or a workaround!

  I am happy to provide assistance on behalf of HP. I do not work for HP.

• HP Photosmart D110: unable to connect my wireless settings

  My printer says that your wireless router requires a WPA security password. How do I do that? My printer was working fine and now it says offline when I want to print on the printer it self says its not connected

  Your WPA paraphrase is in your router under Wireless tab. You need to access your router via its web page and look it up. It's the same when you connect your computer to your routers SSID.

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Unable to connect to secure linksys WRT54GS2 V1 wireless router

  I just moved in with my friend and I'm unable to connect to linksys WRT54GS2 V1 wireless router.  My roommate can connect his computer laptop and desktop to the wireless router, but my iphone and the laptop cannot connect.  I tried both of my devices on a wireless network to a friend, and all both worked well.  We even changed AND removed the password and it won't let me log on to internet.  I went through the forumns and FAQS on the site, looking for suggestions.

  Thank you

  Are you MAC to your iphone and laptop addresses in the filter?

• Unable to connect to the netgear router, it says failed to connect check connection

  Original title: netgear router

  Im trying to connect to my netgear router a TI repeat check connection failed to connect, but I can go on the internet. He began to do after I changed the channel on the router one moment I can reconnect you to fix. or go to the web page on the internet to solve if someone could help me that would be great.

  Hello

  1. What is the model No. the Netgear router?
  2 have you tried to login using the different browser and check?

  Check out the following link and check if you can access the router page.

  
  

  If you are unable to log on to your router

  http://KB.NETGEAR.com/app/answers/detail/A_ID/1097/~/if-you-cannot-log-on-to-your-router

  Alternatively, you can contact Netgear support for more details:

  http://forum1.NETGEAR.com/

  If you have any other questions, answer here and we will be happy to help you.

• Unable to connect TV to new router

  KDL-46HX820. In the process of setting up the TV, I properly connected by Wi - Fi on my router Linksys Valet Wi - Fi. Later, I replaced this router with a Linksys E4200. The Linksys router has generated its own network ID and password. I tried to connect the TV to the new wireless router using the WPS process, but the TV will not connect.

  What should I do to get the TV to connect to a new wireless router with a new network ID and password?

  Thanks for any help.

  Try to assign a static IP address for your TV. First of all, you need to find the address of the gateway of your wireless device. In a computer that is connected to your wireless network, you can open a command prompt window (start - run - cmd) and type ipconfig. This will give you the address of the gateway (for ex: 178.152.1.1)

  Then go to the TV and go through the configuration of the network (wireless).
  When you configure IP address and proxy, choose (custom instead of Auto).

  Then proceed as follows:
  IP address: 178.152.1.15
  Address of subnet 255.255.255.0
  Default gateway 178.152.1.1
  Primary DNS 8.8.8.8
  Secondary DNS 4.2.2.2

  Note that the IP address and default gateway is the same as your gateway address you got from the computer except the last figure of the IP address.

  Then browse the rest of the setp upwards and who need to connect to your wireless router

• Satellite A110-195 unable to connect to the WLan router

  Hello

  I have a wifi router and I have connected my laptop and it worked wery well but on low there is I could not conect to router but woudn't ip address pop up. Internet access was not.
  I am connected to the same router another device and it worked...

  Hello

  Believe me, there is no general solution, you must check all the settings of your operating system

  First of all that I recommend to check the parameters of the TCP/IP protocol if everything is settled automatically on.
  Then check if you are using encryption parameters right as standard (WEP, WPA, WPA2) encryption and the encryption key.

  It s also advised to reinstall or update the Wlan card driver

  If you used the windows own WLan configuration, I would recommend testing as Atheros Client utility or Intel ProSet Wlan client configuration utility. But it depends on the WLan card what client WLan configuration utility can be used

  concerning

• With the help of Windows Vista Edition family and unable to connect to the Netgear router.

  No matter what patches I try, I still, I get a message error "settings saved on this computer for the network do not match the requirements of the network. Two other latops under Xp and Windows 7 connect perfectly.  The user called Geeksquad who told him it was the router. Replaced the router and the same issue. This default laptopp local only access point. Fix regedit for broadcast and Fixit file downloaded here have not solved the problem. Have you tried to push the direct connection button on the router, change the network connections settings... everything. Nothing works. Help, please! The user of this laptop is uber frustrated. I don't know what else to do.

  Geek Squad - use if you do not want necessarily fixed it - but you like overspending for no reason.

  Sounds like a bad driver/software.

  What is the wireless network device in the system in question (I hope that something like Intel...?)

  Is the latest software and drivers from the manufacturer of the device (don't not relying on Microsoft)?

  May need to remove all network components, reset it and install the latest drivers - and if you think Geek Squad would do that...  They could - if you get a child who loves really networking of their own things at home - but the odds are against it.

• Unable to connect to Internet through router WRT400N.

  I was able to connect to the Internet via the wireless, but not today it stopped working (without computers can connect if not just my wireless). I am able to connect to the Wireless router and update the parameters, I am able to connect to the wired router and change the settings. I am able to connect to the Internet by plugging directly into the modem and using this same cable I plug it into the router and then no internet. I don't know what to do anymore as I power cycled many times. Any help will be great. Also - all lights seem to be lighting up as usual.

  Who is your Internet service provider?

  You can access the Internet when you connect the computer directly to the modem. This means that the modem works fine.

  Connect the modem to the Internet port and the computer on the Ethernet port on the router.

  Open the router configuration page and check the settings of the router's Internet connection.

  Follow this link to configure the router with cable Internet service.

  Follow this link to configure the router with DSL Internet service.

• Unable to connect to my new router cable, my XP and Windows 7 machines

  Vista, wireless router Netgear, no link, please help

  No matter what I try, I can't connect to my new router cable, my XP and Windows 7 machines work fine but the Vista laptop are it. Have searched the web, looked at this site and the forums, but nothing does not jump and helps me solve the problem. I use a HP Pavilion DV9000 laptop, all service packs updates and so forth... any ideas?

  I suggest that you contact your ISP and get their help in setting up the Vista machine so it connects properly.  They know the right settings for the access provider, while we do not have and that there may be something else you need to do with Vista which is different of the other two systems (and hopefullly the ISP will also know and be able to talk you through the process).  I call my ISP all the time and they are VERY useful and have ALWAYS resolved any problems, I called (even if sometimes he had a visit from a technician).

  If the ISP Can ' t/don't/can't help you, then after coming back here and we'll try to go through it step by step, even if we cannot have all the information we need.  But I am sure that they will be able to help you more quickly and more effectively and with greater chances of success.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• upgrade to windows 10 and unable to connect to the Netgear router

  After the upgrade to Windows 10, I get a connection limited to the router.  I have tried everything that seems to indicate that I have seen but not solution.  I went back to 8.1 and everything is ok.  Drivers are all to date I can say.  The problem seems to be related to the default gateway or the lack of it.  It is not good to reset the router.  My labtop HP running windows 8.1 works fine but my Dell Inspiron gets only limited access to the router. I need help to solve the end.

  keybaud

  I do not have a Dell, but I'm having a similar problem with the Netgear WNDR4500 v1 router and an ethernet Intel I217-V adapter. 10 Windows does not recognize the router is via the Ethernet connection, but it does not work with a wifi dongle.

  This is to help, adding that I don't expect Dell to solve my problem. :-)

  Hello

  Not sure what help I can give since I know not what system you have, and if it is considered compatible Win10, but here is the link to the driver Windows 10 ethernet Intel 1217 - V cards.  ((NOTE: le lien que je fournis est pour la version 64 bits de Windows 10.))  If you have installed the 32-bit version and then to just change the drop-down list of BONE near the top of this page))

  I would also say that updating the firmware on this router would be your next step.  See if one or both of the Exchange help people.

  If this isn't the case, then remove all your system's ethernet drivers, reboot and see if Windows 10 has all the innate drivers that may work.  Or else let Windows Update search and download a driver.  Who has the strongest chance of finding a compatible driver.

  I hope this helps.

  Todd

• Unable to connect my other laptop to my wireless more

  In addition to having the same problem with the new Ipad. tried to reset the homegroup, sharing, even changed to no password to connect. Same problem does not connect.

  Hi Bernie Niehus,.

  Thanks for posting your query in the Microsoft Community. According to the description of the problem, you are not able to connect to the network via a wireless connection. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         What is the brand and model of the laptop?

  ·         You use a third-party security software?

  Follow these methods.

  Method 1: Temporarily disable the security software .

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Startup options (including safe mode)

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow step 3 from the link to start the computer to a Normal startupmode.

  Method 3: Follow the steps in the article.

  Windows wireless and wired network connection problems

  You can see these articles for more information:

  How can I troubleshoot network card?

  How to reset the Protocol Internet (TCP/IP)

  I hope this helps. Let us know if you need more assistance.