HP Proliant dl380 Server gen9

Similar Questions

• What the BIOS settings need to be enabled for Proliant DL380 Server?

  We will install ESXi 4.0 on a HP Compaq Proliant DL380 server.

  We would like to know what are the options in BIOS would allow (as: support for Intel VT)?

  Thank you

  Post edited by: TonyJK

  I does not change much options BIOS on my equipment except to allow the No. run memory and enable CPU virtualization technology.    Here's a thread that asked the same question, http://communities.vmware.com/thread/125837?start=0&tstart=0

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Smart Array P440ar: ProLiant DL380 g9 & controller Smart Array boot order

  Work on a server of gen9 ProLiant DL380 (SFF) with an of P440ar (version 3.00) at location 0 (embedded RAID) and a controller (version 2.52) P840 to location 1. I have the P440ar connected to the risers on the front of the system, and I'm starting off the P840 6.5 RHEL. If no hard drive is attached to the P440ar, it works, but if all the disks are connected to the P440ar, the boot device is not found. I tried to change the order of boot in RSBU controller, but the P440ar was the ONLY listed controller. I didn't even have an option to change the P840.

  Am I allowed to configure the system in this way?

  After fighting with it for several days, I deleted the system P840 and started with just the P440ar. Then I added the P840 in the system and restarting, the system automatically added the P840 to startup controller command list. Works fine now.

• Expansion / Upgrade ProLiant DL380 G5 and ProLiant DL360 G5

  Hi all, we have two servers, Proliant DL380 G5 with SmartArray 400 and Proliant DL360 G5 with SmartArray 200icontroller controller, expand us on the disks, memory and cards network, the problem is that after we see the documentation which is sometimes wrong and don't know not the limitations of each of the parties, the issues are:

  Proliant DL380 G5 SmartArray 400:
  - STORAGE: up to 8 SAS / SATA, not clear what size that can be used with this controller, we understand that up to 500 GB SATA 7200 RPM and maximum 2 TB SAS 7200 RPM, we currently use with 146 GB drives to 10,000 rpm, whose original documentation is the maximum allowed value.
  -MEMORY: Up to 64 GB modules of maximum memory up to 8 GB.
  - NETWORK: update with PCI Express, support cards that I can find are HP NC110T PCI Express and PCI-Express HP NC373 HP NC360T PCI-Express.

  Proliant DL360 G5 SmartArray 200i:

  - STORAGE: up to 4 SAS / SATA controller supports only 200i SmartArray four drives in RAID 0, 1, 1 + 0 if we wanted to expand to six bays that are available on the disk server, it would change the controller and memory. Yet, the size of disk maximum supported based on the documentation is 72 GB SAS and SATA drive 60 GB, but looking it seems as if you agree at least 300 Gb SAS disks at 10 000 rpm and up to 500 GB 7200 RPM.
  - MEMORY: up to 64 GB maximum memory modules up to 8 GB.
  - NETWORK: update with PCI Express, support cards that I can find are HP NC110T PCI Express and PCI-Express HP NC373 HP NC360T PCI-Express.

  This is what I have gathered and what interests me in the expansion and to say that the documentation I found to give the feeling of this conflict, is perhaps by the dates of their procedures, but before you make a payment would guarantee the purchase. Also getting information guides, manuals and forums, I have also consulted compatibiliy HP Proliant Server Guide, so I have consutlado with HP before purchasing, but have yet to receive an answer.

  A greeting and thank you very much

  Hello jranerosc. I think you'd have better luck trying Business Forums of HP. You should get more specific help.

  Have a great day!

• Error installation license: not an activation key valid. HP Proliant DL380 G7

  Product name ProLiant DL380 G7
  UUID 30303734-3536-5A43-3232-30353038355A
  UUID (logic)
  Product ID 470065-490
  System ROM P67 05/05/2011
  Backup system ROM 05/05/2011
  Integrated remote console Java .NET
  ILO 3 Standard license type
  ILO Firmware Version 1.26 August 26, 2011
  IP 192.168.12.233

  When I try to install iLO advanced license (trial version) I get the error (in the subject).

  [number removed for privacy]

  The problem was an incorrect date of the server.

• 5.1 and HP ProLiant DL380 G5 - Xeon DualCore 5160 ESXi | 2 x 3.0 GHz

  Hello!

  I have the opportunity to buy a HP ProLiant DL380 G5 with:

  • N. 1 DualCore Xeon 5160. 2 x 3.0 GHz
  • 2 x 72 GB SAS HD - 10 k Hotplug
  • Smart Array P400
  • 8 GB DDR2 RAM

  Someone at - it successfully installed ESXi 5.1 or al least 5.0 on this server?

  Thanks in advance

  Hi guys!

  I bought the server and installed custom HP ESXi 5.1 on my Proliant DL 380 G5 (Customize the Images VMware ESXi for HP ProLiant servers) and everything works like a charm!

  Thank you all for your support.

• HP ProLiant G6 Server SE316M1: Overclocking CPU on HP ProLiant G6 Server SE316M1

  Hello

  I have in mind to buy a HP ProLiant G6 Server SE316M1. The prices are really cheap on some merchants.

  I saw on a cue that it was possible to overlock Xeon E5645 2.40 Ghz.

  Of course I need stability, but I hope to accelerate both CPU up to 2.80 Ghz.

  I don't think it's possible, but I prefer to ask the community.

  Thank you very much.

  Hello:

  Here is the manual in the BIOS Setup for the prospective server that you want to buy.

  http://h20628.www2.HP.com/km-ext/kmcsdirect/emr_na-c00191707-19.PDF

  I typed the word "overclock" in the search window, and nothing came.

  Here is the main support for the server page...

  http://h20565.www2.HPE.com/portal/site/hpsc/public/PSI/home/?sp4ts.Oid=3884343

  While I have not read the manual in its entirety, nor I know much about HP servers, I usually have a good amount of knowledge about laptops and HP business desktops and I can tell you that none of them offer overclocking processor, graphics and memory options.

  I have to assume that since HP must provide assistance guaranteed at least one year on most of these products (mine all had them 3 years warranty), it would not be in their interest to provide for overclocking options in their PC, because we, end-users could fry components due to overclocking and then to file claims under the warranty.

• Data store / latency issues with HP ProLiant DL380 G7 - controller HP Smart Array P410i after disk 2014.09.0 SPP / hpsa - 5.0.0.74 update

  Hello

  We are currently investigating massive data store and the problems of latency of disk (mainly READING) on some of our HP ProLiant DL380 G7 with P410i (BBWC) controller.

  It all started after our half of regularly updated cycle for ESXi 5.1 U2 to:

  ESXi510-201407001 (no problem)

  -hp - esxi5.0uX - bundle - 2.1.1 - 2 (no problem)

  -HP-HPUtil-esxi5.0-bundle-2.1-15 (no problem)

  -hpsa - 5.0.0.74 (pilot) & SPP2014.09.0 (-assigned problems)

  It is not a permanent increase in the latency of reading, but rather meeting points that trigger alerts of Veeam. Store of data read latency increases about 5 MS to 100 ms as soon as this happens, but after a few seconds, everything is back to normal. These data warehouses special are RAID5 (but we have also seen some alerts on RAID1), having read and write cache enabled and the most affected machines are those with the LOWEST its use.

  We have a few WinServer2012R2 RDP for a small number of sessions (less than 5) - there is no noticeable delay on work on these.

  Maybe someone of you knows a similar behavior after you apply the updates of HP ProLiant servers. We don't have any idea on what to try next, a SPP restoration is not possible, maybe the pilot, but we find the correct predecessor, as the old drivers of 2014 HPSA leads the Group on the host computer.

  Best regards

  HZ

  Hello

  most likely, you have already solved the problem... I did some research and was in contact with HP. It is a problem with the driver hpsa - 5.0.0.74. It occasionally crashes when used with P410i. In the papers, you can find "WARNING: LinScsi: SCSILinuxAbortCommands:1843: failure, pilot hpsa to vmhba0. HP knows talking and working on the new driver. As a workaround, you can use hpsa - 5.5.0.60 (at least it works well for us).

  BR

  Maachah

• HP Proliant DL380 G4 Red Hat 5.1 Linux P2V

  Hello

  I'm trying to P2V a HP Proliant DL380 G4 with Linux Red Hat 5.1.

  I did a basic cold migration and found that I was getting panic the kernel. Looking through the mistakes, that's because migration cold does not provide the correct drivers etc. to the controller raid etc..

  What I want to know is:

  What is support/how to P2V a Linux OS with RAID etc configurations?

  Is there documentation?

  Personally Im lazy and I'd like to see for a moment, and then click software if possible.

  I P2Ved a bunch of them - but to be honest, we had problems in the start menu and ended up using Platespin Migrate (PowerConvert)

  We talked to one of our COMPUTER resellers and they gave you a free for a migration or two - licesnse if at least we were able to test the product.

• VMS 64-bit on HP Proliant DL380 with ESXi 4.1 G4

  Hello world

  Impossible to install 64-bit VMs on HP Proliant DL380 G4's with ESXi 4.1? I received an error message:

  msg.cpuid.noLongmodeQuestionFmt: this virtual computer is setup for 64-bit client

  operating systems. However, the 64-bit mode is not possible.

  Longmode is disabled for this virtual machine.

  For more information, see http://VMware.com/info?id=152 .

  Continue without 64 bit support?

  Can someone explain to me and indicate a solution for this problem?

  The link also does not work...

  Where and how can I activate the Longmode?

  Thanks for your attention

  You must enable VT in the BIOS of the system and probably not execute (or disable it, always, I forget which).

  Doing so once the power to change the system, remove the cards power and then turn back on and you should be able to create x 64 vm

• ProLiant DL380 G6 memory configurations

  Our servers ESX host of base HP Proliant DL380 G5s in recent years (2-Quad Core procs with 32 GB of memory).

  We intend to jump to the G6s DL380 (2 Quad Cores and 64 GB of memory) and I always rolled my head around configurations of memory. Looks like I could go with 8-8 GB or 16-4 GB Dual RDIMMS. For our company, I don't see us willing to go more than 64 GB for a host for the free slots aren't a concern.

  The choice seems obvious because of differences in cost between the two. I guess this leaves of performance.

  1. What is the difference real performance one would expect between these two configurations?

  2. This change when we jump from ESX 3.5 to VSphere?

  3. Are there other aspects that I'm on.

  With the virtualization environment, more memory of course provide best performance and host virtual machines more than you have known, the only thing that would be if you must attach these 2 types of hosts G5 & G6 in a cluster, you will be not able to VMotion and you should activate CVS to work otherwise use CPU masking in the parameters of the advance on CPUID NX indicator that could do otherwise use VMware CPU Compatility tool to check that well.

  Many of my clients are satisfied with DL360 G6s and also running 64 GB of RAM but it using DIMMs 8x8GB.  I would use whatever it is cheaper for your cost as long as it has the same requirements of 64 GB of memory.  Unless you have plans for the future expansion of 128 GB, then using 16 x 4 DIMMS would be a long-term strategy.

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

  Kind regards

  Stefan Nguyen

  VMware vExpert 2009

  iGeek Systems Inc.

  VMware, Citrix, Microsoft Consultant

• ProLiant DL380 Gen9 - grouping of NETWORK cards

  Hello community,

  for a week we have new servers DL380 Gen9. Now, we want to install a server Win 2008 R2, but we cannot create a collection of NETWORK adapters.

  If I install the HP NCO (Network Configuration Utility), cp023339.exe Version 10.90, I get

  "The bot software will be installed on the system because the required hardware is not present in the system or the software/firmware does not apply to the system"

  I updated the driver / firmware of the NETWORK adapter have sought new HP Network Configuration tool, nothing.

  NIC: Map 1 GB 331i 4 ports Ethernet HP

  Can anyone help?

  Thank you very much

  / Hugo

  Hello:

  You can also ask your question on the Business - servers DL HP Support Forum.

  http://h30499.www3.HP.com/T5/ProLiant-servers-ml-DL-SL/BD-p/ITRC-264#.VHM-jHktC9I

• HP ProLiant DL360p Server Fax Modem Gen8

  Hello:

  Any recommended FOIP connector or fax external modem that is compatible with a server HP ProLiant DL360p Gen8.  need at least 4 ports and external.

  Hello:

  You can also ask your question on the Business - servers DL HP Support Forum.

  http://h30499.www3.HP.com/T5/ProLiant-servers-ml-DL-SL/BD-p/ITRC-264#.VTkq2TgtHGg

• HP ProLiant DL380 G4 can not install Windows 2003 x 64 error «...» CPU is not compatible with x 64 mode... »

  I try to install a Win2003 64 bit VM on ESXi 4 but get the error that x 64 processor not supported. The server has Intel E7520 Chipset and Xeon 2 x 64-bit clocked at 3.6 GHz processors. It should be possible to run virtual machines with Win2003 x 64, right? Anyone know what I'm doing wrong?

  Thanks for any help.

  While ESXi 4 will install, DL380 G4 platform is not supported.  This generation of processor (Xeon 51xx) taken supported operating systems for 64-bit, but there is no VT extensions.  It's why he can't support 64-bit clients.

• ProLiant DL380 Gen7: Not found Base system device driver

  Hello

  I need a Base system device driver

  PCI\VEN_0E11 & DEV_B204 & SUBSYS_3305103C & REV_03
  PCI\VEN_0E11 & DEV_B204 & SUBSYS_3305103C
  PCI\VEN_0E11 & DEV_B204 & CC_088000
  PCI\VEN_0E11 & DEV_B204 & CC_0880

  Hello:

  There is no W7 drivers for this device.

  See if the driver for Windows Server 2008 R2 works, which would be the equivalent driver.

  http://h20566.www2.HPE.com/hpsc/SWD/public/detail?sp4ts.Oid=3884321 & swItemId = MTX_313bf6ab46dc458191c563ff5c & swEnvOid = 4064

  Try to install the driver manually if automatic installation method does not work, because this driver is not in favor of the ID you have posted.

  [HewlettPackard.NTx86.5]
  DeviceDesc % = CpqCiDrv_5, PCI\VEN_0E11 & DEV_B204 & SUBSYS_B2060E11
  DeviceDesc % = CpqCiDrv_5, PCI\VEN_0E11 & DEV_B204 & SUBSYS_3304103C
  DeviceDesc % = CpqCiDrv_5, PCI\VEN_0E11 & DEV_B204 & SUBSYS_3305103C