HP r046tu: driver Intel (r) engine run Interface to windows 7

Mr President. the Intel(r) trusted execution Interface engine isn't initalizing. Please help me I think that the driver I have installed is not compitable for windows 7. Thank you.


The following link is to Windows 7 (32-bit) *, Windows 7 (64-bit) *, Windows 8, 32 - bit *, Windows 8, 64 - bit *, Windows 8.1, 32 - bit *, Windows 8.1, 64-bit *


Are you sure that your computer supports this?

Kind regards.

Tags: Notebooks

Similar Questions

  • Driver Intel management engine interface not supported

    I use HP2000-2116TU laptop, installed with WINDOWS (32 bit) operating system 8.1. When I try to install the driver Intel management engine interface, downloaded from the hp Web page, it says that it is incompitable with the system. When I check the Device Manager, it shows pci communications driver is missing. However, driver bluetooth, preferred for my system in HP Web page also is incompitable with WINDOWS 8.1 operating system.

    Please give me a solution for this problem.

    Details of the problem:

    1 PCI device:

    The drivers for this device are not installed. (Code 28)

    Hardware ID:

    PCI\VEN_10EC & DEV_5229 & SUBSYS_1858103C & REV_01
    PCI\VEN_10EC & DEV_5229 & SUBSYS_1858103C
    PCI\VEN_10EC & DEV_5229 & CC_FF0000
    PCI\VEN_10EC & DEV_5229 & CC_FF00

    Compitable ids:

    PCI\VEN_10EC & DEV_5229 & REV_01
    PCI\VEN_10EC & DEV_5229
    PCI\VEN_10EC & CC_FF0000
    PCI\VEN_10EC & CC_FF00


    It's the driver who interested, if unfortunately, I don't know why it does not work.

    Try to force the installation...

    Download and run the file again.

    Now, go to Device Manager and click the comms controller simple pci who need the driver.

    Click the driver tab.  Click on set to update driver. Select her browse my computer for driver software method, then at the bottom of the window, let him choose from a list of drivers for devices on my computer.

    Click on disk and navigate to the folder of the driver that was created when you ran the file.

    That will be located in C:\SWSetup\sp58464\Drivers\MEI\HECI\and, select the device Intel(r) Management Engine Interface in the list and see if the pilot goes like this.

  • 8086 3b 64 = driver Intel Management Engine Interface (MEI)?

    I have a new computer that was custom built for me by a shop.
    The computer works fine, I noticed in Device Manager, however, that in the other devices section
    There is something called "PCI Simple Communications Controller" which has a yellow exclamation point.

    On the site www.pcidatabase.com
    I looked at the details of the pilot, the vendor: 8086 Dev: b 3 64 SubSys:83831043

    On the page of intel, it is listed at the bottom article pending... the chip is listed as Intel Management Engine Interface
    What is c? The note on the pcidatabase said something about laptops that confused me.
    Googling "Intel Management Engine Interface" did not come with something relevant.

    What is the IMEI, I download this driver? Can someone enlighten me?

    Im running windows 7 64-bit, intel core i5 750 processor desktop computer.


    The "Intel Management Engine Interface" is a part of the VPro technology from intel.

    This IMEI technology allows you to manage your remote pc.

    You can download the update of the driver for your chipset.

    See the link below for the procedure to install this update.


    Kind regards
    Amal-Microsoft Support.
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Satellite Pro S500 - 11 c - lack of driver Intel engine Interface


    I had a Satellite Pro S500 - 11 c Windows 7, I see an unknown device in the information system. The missing driver appears on PCIdatabase.com as Intel Management Engine Interface (MEI) driver, but I can't find it on the Toshiba site, and when I go to the Intel site there are several versions with no obvious way to tell than I need.

    Can someone tell me what version I want or where I can get it?

    Thank you

    Try to download this driver:


  • CQ2909E0 - Intel Management Engine Interface driver for Windows 7


    I installed Windows 7 on my desktop CQ2909E0, but need me a "PCI Simple communications controller" and the Ethernet controller. I think I must install the com controller before I can install the ethernet controller. It is; I can't find the right driver for the PCI card.

    Please notify.

    You should be able to use software HP and Driver Downloads page of the desktop HP Pavilion p2 - 1117 c. This unit and your, use the same motherboard basis and therefore most of the drivers should work on your computer.

    Simple Communication controller is the Intel Management Engine Interface driver and the ethernet controller is Atheros network controller driver. The rest of the driver should work as well.

    Please send BRAVO

  • Intel® Management Engine Interface driver

    Intel® Management Engine Interface Driver for Windows 8 Pro. 64 bit
    one that I find DOES not work... everyone you have a difficulty?

    Please provide the name of the model of your VAIO computer.

  • How can I reinstall the Intel Management Engine Interface?

    Hey there. I have a Lenovo Yoga 2 13, i5 and have some problems with the boot and sleep.

    Startup problem: it takes 30 sec - 1 min at startup and display the Lenovo logo and the rotating circle

    Pépin to sleep: the most of the time, if I close the lid for more than 20 seconds and open it again the screen starts flashing and then the computer shuts off.

    So I tried the problem to resolve these issues, which lead me to the "Device Manager" where I have a past by each element and check for driver updates. Surprisingly, there were about 5-6 required. But the "Intel Management Engine Interface" did not work. The first time, it gave me an error and the second time (he had always the sign of error small triangle on yellow), he said that all the drivers are up to date. In my reading of the internet, some people were saying that the most recent update for this chipset was causing problems (ver.11) and that I should downgrade to version 9. So I uninstalled the driver, and then (I have a feeling that it was my mistake) also uninstalled the "Intel Management Engine Interface" how it disappeared from my list of 'Device Manager '. But when I tried to install the driver again for version 9 the error that appears is "this computer does not meet the minimum requirements for installing the software. Worm. 11 also gives me an error (even if I don't remember right now).

    I have scowered the internets and found nothing even come close to answering that question. Any help appreciated.

    As a side note, I also have some freezing problems when I plug in the power adapter, even if I think that maybe I should ask this question in another post...


    Fixed. She appeared again in the device again Manager and I was able to do the downgrade. Don't know if I've seen a much improved...

  • (Redirected) Alienware Aurora R4 - cannot install Intel Management Engine Interface


    I had this problem for quite a while now. Since I reinstalled Windows 7, the "Intel Management Engine Interface" driver does not install correctly. It gives me an error code 10. I can't find solutions for this problem.

    Help, please.

    Thanks in advance,


    Better in this position in the Alienware owners Club Forum, here:



  • Re: update type Intel Management Engine Interface

    Simply receive uprgade notes...

    * heci - 20150320101654.zip *.
    Data di ultima changes 20/03/15
    Ragione social Intel
    Type Intel Management Engine Interface

    Whatever it is, what to do?

    It is necessary? It is safe?
    Thank you

    Can you please tell us which laptop model you have and what operating system are you using?

  • Venue 11 Pro BIOS / Intel Management Engine problems


    Recently my Tablet Dell place 11 Pro 7130 (vPro) with Windows 8.1 x 64 has had problems applying power. He would have before start in 20 seconds or so, and now it may take a minute or more before you post what whatsoever.

    In the Device Manager Windows "Intel Management Engine Interface" shows an exclamation point and wrote:

    "The device cannot start. (Code 10)


    The research forums, I tried to update the drivers of the IME by using different versions. I tried to Dell website, as well as Intel. They all fail to install with the same error as above.

    Here are the most recent driver Dell tried support:


    When I tried to Flash the BIOS of the A12 A13, it gives me no errors, loin very well until he decided to restart. After the reboot happens exactly as previously having never run the BIOS flash.

    I reached out to Dell support and they tried to install the same driver over and over again (about half a dozen times or more) before they me just reinstall my OS based on what forums suggest.

    So what I asked of them is a replacement motherboard, I get not anywhere, but I feel that it is all related to these problems:



    Can someone enlighten us more on this topic? I don't think a reinstallation of the operating system will solve this, and my current thoughts are I'm stuck without being able to Flash the BIOS thats why IME is bad mood against me.

    I'm not tense at this point, all hope based on the forums that I will get this tablet in good operating condition, and once the dell technical support suggested I ignore the error it lead me to believe that I'll buy a new Tablet 8 months in possession of it.

    Thank you.

    Unfortunately, you will need to return the unit to the deposit to this fixed.   Once a unit is in this State, it is not possible to update the BIOS via the customer facing tools.   Deposit use a special tool which allows to overcome and correct state.   Apologies for the inconvenience.   Note that the most recent BIOS version have fixed ME Intel which should avoid this problem again.

  • HP Pavilion Notebook - 15-p247: I can't update my display driver intel

    My display driver intel continues to crash, reboot and make the computer freezes.

    When I use HP Support Assistant, I see not all the drivers on the update tab.

    When I use the HP website to download graphics drivers, there are two of them, and they both are not compatible with my computer.

    So, how can I stop my computer from freezing?


    Ok.. I see now the 2nd driver Intel graphics... This is the one you want.  The other is for portable computers with Pentium processors.

    This package provides the driver that allows graphics Intel high definition (HD) in the notebook models that are running an operating system supported. If the video output high-definition multimedia interface (HDMI) is supported, this package also installs the HDMI Audio Driver.

    File name: sp69623.exe

    Since you have already run this driver and it didn't work, let's try the following...

    In Device Manager, expand display adapters, right-click the Intel HD graphics card and select "Update Driver Software".

    In the next window, select "Browse my computer for driver software", then "Let Me pick from a list of drivers for devices on my computer.

    In the next window, click on the button "Floppy", then go to C:\SWSetup\sp69623\Graphics\ and left click on the 103633.inf file to select it and then click Open.

    Click 'Ok' and then click 'Next' and see if the pilot goes like this.

    One when you're done, click on 'Close' and then click 'Yes' to restart the laptop.

    You can also try this method even with the latest Intel graphics driver for your laptop directly from the Intel site, if the driver above fails to solve the problem.

    Use the 64-bit zip file.


    The only variation to the above procedure would be to right click on the zip file of Intel graphics driver, select extract all in the list and select the igdlh64.inf file in the images folder.

    This process has worked for another Member of the forum with the graphics card Intel HD 4400 and W8.1.


  • Failed: Intel management engine Firmware Recovery Agent

    My new Y50 automatically runs a program called "Recovery Firmware Intel Management Agent" engine. This software checks the updates of drivers/firmware. HOWEVER on my machine updates verification FAILS. The error message is: 'we're sorry, but the updates verification could not be completed. Please make sure that your system has Internet access. »

    Has anyone encountered this problem? Can anyone suggest a solution?

    I tried to solve the problem by downloading and installing the latest driver from Lenovo (http://support.lenovo.com/us/en/products/laptops-and-netbooks/lenovo-y-series-laptops/y50-70-touch-n... but that did not help.)

    Thanks for your time

    Y50_user wrote:

    My new Y50 automatically runs a program called "Recovery Firmware Intel Management Agent" engine. This software checks the updates of drivers/firmware. HOWEVER on my machine updates verification FAILS. The error message is: 'we're sorry, but the updates verification could not be completed. Please make sure that your system has Internet access. »

    Has anyone encountered this problem? Can anyone suggest a solution?

    I tried to solve the problem by downloading and installing the latest driver from Lenovo (http://support.lenovo.com/us/en/products/laptops-and-netbooks/lenovo-y-series-laptops/y50-70-touch-n... but that did not help.)

    Thanks for your time

    That's what I've learned about the problem that you have:

    Intel longer supported Intel independent firmware Recovery (IFR) function so that it is advisable to remove the RSI program.

    How to:

    1. go in Control Panel / "Programs and features" using the Windows key + X.

    2 remove the Intel management engine Firmware Recovery Agent

    3 reset

  • HP Pavilion dm4: graphics driver Intel & AMD causing Windows Crash


    My laptop is

    HP Pavilion dm4-3107tx Beats Edition Entertainment Notebook PC.   I tried to install the graphics drivers from this link:


    but I could not install the graphics card intel. It is said that the cell does not meet the minimum requirements of the graphics driver.

    I also tried to install AMD and he did. But every time that I reboot, Windows startup crashes.

    I also noticed that results for starting blocked when I recently updated my Windows, including the update for the driver intel which I have not yet installed (because I know that once I did, I do a lot of recovery and repair of the system for the umpteenth time).

    And now I feel really stressed out about it because I've been formatted my laptop for the second time, and the last time it was with the release of the pilot intel. I was stuck again started back and I got really tired of him.

    I really need help with that.

    What I have to install ALL the drivers in the link before installing graphics drivers to ensure that graphics drivers will install?

    Hi @katrinahahaha,

    Thank you for your query.

    I understand that you have a problem installing your graphics drivers.  After formatting the drive and installation of the Intel graphics driver, you have a problem starting.  Did you use the Recovery Manager to format and reinstall Windows 7?

    You only need to install the driver AMD of the HP driver page because it contains the two pilots.  Please try this process:

    • Uninstall and remove two graphic drivers
    • Restart your laptop
    • Run the HP Support Assistant to help find and install the graphics drivers
    • You can also after the uninstall, remove the driver and restart, download and install just the driver AMD.

    HP Support Assistant

    If this problem persists, try removing both drivers and using the Recovery Manager to install the drivers:

    Computers HP - using Recovery Manager to restore the software and drivers (Windows 7)

    Please let me know the results.

    Thank you! If it helps you to find a solution, please click the button "accept as Solution"down below in this message. "If you want to say 'Thank you' to my effort to help, click on the" ""Twww.Mountainview.rsb.qc.ca Up ' give me a Kudos.

  • Qosmio screen X 875-black q7380 when installing graphics driver intel hd 4000


    I have a qosmio toshiba X 875-q7380 when starting Windows 8 screen was black and never started so I decided to move to W7, the installation has functioned well until I have install the display driver intel, then the screen is black and will not start.

    If I press F8 and failsafe mode works well, I would uninstall the Intel graphics HD4000 card driver and then start normally.

    Is there a solution to this problem?
    Thank you very much

    Post edited by: yop787


    > .when from Windows 8 screen was black and never started

    The Toshiba Qosmio X 875 - Q7380 has been pre-installed and configured with Win 8 OS.
    The laptop should run correctly using the factory settings which means that the use of Win 8 should not be a problem.

    Intel HD graphics unit is part of the CPU. I m not very well, but I guess that the issue could be due to hardware problem CPU.

    Of course this is only my personal opinion, but I think that in cases where the laptop does not work using the factory settings, malfunction of the equipment is possible.

  • Satellite C660 - latest graphic driver Intel is 2012

    Im trying to run a software on my laptop (the Zwift new cycling). The custom of executed product and the support team that I need to update my driver on my Satellite C660 - 64 bit Windows 7. The latest version I can find what I have. Is there nothing since? Do I have to upgrade my laptop?

    Thank you


    Display driver update on mobile machinery is quite problematic. Because of the specific and limited design cooling system, the temperature must be all the time under control.
    New display driver means more performance and more performance means more heat, so in the worst case GPU may be damaged or your laptop often stops because of the critical temperature of material.

    In any case, I would check if the most recent driver is available on the Toshiba support page but you must put the name of the full model of your laptop (C660-xxx).

    Have you tried to find or install driver Intel support page?

Maybe you are looking for