HP Web Jetadmin 10.3 and LaserJet M1536dnf MFP communication error

Similar Questions

• HP LaserJet M1536dnf MFP stores the faxes to be sent the

  The company that I work has two HP LaserJet M1536dnf MFP Copier/printers-faxes. They are configured as basically the same that each related to its own line of ananlog fax. One of the machines is a continuous problem where it starts to store faxes instead of sending them.

  I went through all the HP troubleshooting documents. All settings have been verified. Firmware has been updated to the latest version. When I run the fax test via the service menu, always happens on all points.

  The machine receives faxes fine, but when you try to send a fax, it stores and never sends it. Following the troubleshooting documents HP, 02/11/12 I restored by default. After that, the machine was able to send faxes normally do not their storage. On 09/11/12 machine began to store faxes rather than send them again. Today, 15/11/12 I restored default again, and the machine is able to send faxes again.

  I have not the time to be constantly dealing with this issue. Why does the machine start storing faxes instead of sending them? How to prevent it from recurring? Should the machine be returned? Please do not direct me to a generic help document that I have already read. Thank you.

  I would contact HP directly on it. It may need to be replaced, or it may just need some deeper resets. Their Laserjet experts know that go with this problem. I would wait until the problem returns to the top to call, because they will tell you to do if you call while it works very well. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  HP Technical Support call case form:
  http://goo.GL/w7Hgh

• HP LaserJet M1536dnf MFP responds automatically faxes

  My new HP LaserJet M1536dnf MFP does not automatically fax calls.  I don't have a phone hooked or a voice mail/answering machine.  "Answer Mode is"Auto".

  We use an analog converter to connect to our internal digital VOIP phone system.  Prior MFP which was connected has not had problems with answering machine/printing faxes.

  I can see "Incoming" call on the screen, but it just rings and rings.  If you press the button "Start Fax" when it rings, then he will proceed to the connection and receive it, it finally drops the call.  It's not good to see many faxes come when the office is closed or otherwise unattended.

  I tried setting "Fax / such", but that no longer works.

  Help, please!

  Thank you very much!!!

  Hi @DW - OH,.

  I see by your post that faxes will not come by when it is set to auto or Fax / Tel, but manually, you can receive the fax. I can help you with this.

  Update the firmware of the printer.

  HP LaserJet Pro M1536dnf multifunction printer drivers.

  Select your operating system, click Next, click the link for the firmware.

  Please check your messages for the reset of the printer, I saw that solve this problem before.
  In the forum next to your handle name simply click on the envelope to see.

  Good day!
  Thank you.

• Drivers to be used on networked computers that are not directly connected to the HP Laserjet M1536dnf MFP

  Hi, I had problems connecting to computers on the network for printer. The printer is HP LaserJet Pro M1536dnf MFP. The computer that is connected to the printer directly via USB is fine. I downloaded solution complete driver installation on the site of hp, them and everything's fine. the problem is with the computers on the network, they cannot detect even the computer to add printer. And I have enabled file sharing and printer sharing advanced options of sharing on all computers. I also tried to install the same drivers I used on the local computer on the network computers, but its does not work. Please kindly advise me on which particular driver should I use or the solution.

  for this one, there was a simple solution... I forgot one small thing. After the installation of the complete solution from hp printer drivers on the computer connected to the printer via the usb port you then go to control panel > view devices and printers > click with the right button on active printer installed > printer properties > sharing > click on the list to the Director. that allows other computers on the network to view the printers.  was a bit stupid coz the solution was so simple.

• LaserJet M1536dnf MFP: It won't work

  I use this printer on a LAN port.  It appears in the network when I search for it.

  When I double-click the icon it installs automatically 2 drivers.  One of them has not installed whose name appeared as 'WSD printer driver' (something like that).

  It is strange because I have installed successfully on the other PC that is sharing the same network.  No matter how many times I reboot this computer, or remove and reinstall the printer in control panel it just will not work.

  More suggestion on what can I do?

  Hey @penguin97,

  Welcome to the Forums of HP Support! I hope you enjoy your stay here.

  I understand that you have some problems with your Windows 7 PC printing on your printer LaserJet M1536dnf. I can help you with that.

  Here's what we will do:

  1. If you have any software associated with your printer on this PC, uninstall it.
  2. Click on start and devices and printers.
  3. Right-click on any icon of your printer listed.
  4. Click on remove the instrument.
  5. Repeat for all other icons printer listed.
  6. Automatically search for updates of Windows 7. Install all updates, not only the critical updates.
  7. Restart your PC.
  8. Download and install the latest drivers by clicking on this link.

  At this point, you should be able to print. If not, please let me know what happened following my directions.

  Please let me know if you are able to print or if you have other questions. If not, have a great weekend!

  If this solves your problem, then please help others find this post by clicking on accept as Solution on my post.

  If you appreciate my help, so please let others know by clicking on the icon below my post thumbs up.

• HP LaserJet M1536dnf MFP

  I have a MFP HP LaserJet M1536dnf who has E-Print.

  My internet hub is in another room for my printer so they are not connected.

  Is there anyway I can print wirelessely without connect via USB to the computer or connect the printer to the hub?

  Any help would be great.

  Thank you

  Tracy

  Hello Tracy,.

  The requested ePrint service a network connection with internet access, connection via USB to a computer is not supported for ePring, a wireless network connection is not supported for the printer itself.

  You can connect to hub you using an Ethernet cable so ensure it have access to the internet, otherwise ePrint will not work.

  You can find out more information on ePrint in the following document:

  http://h30434.www3.HP.com/T5/user/viewprofilepage/user-ID/2585903

  Shlomi

• HP Laserjet M9050 MFP: Scan error Code 30.01.16

  I have a HP Laserjet M9050 MFP Firmware: 51.051.4

  The printer was woking fine so far, but played upward...

  I get an error Scan on the screen 30.01.16 Code, have searched online and this indicates that the scanner ADF need of recalibration.

  Normally the 30.01.16 error code will remain on the screen, but if I take off the cable behind the scanner it-displayed meaning I can access the control panel and enter the menu etc.

  I tried to re - calibrate the, but it doesn't seem to work, someone has another idea about what it takes to solve this problem.

  Hahaha...

  Be sure to save the configuration when you do something.

  Well, the solutions were:

  (1) printer tour

  (2) remove trainer card and unplug the hard drive

  (3) re - connect trainer Board and open the ADF tray, printer

  4) go to Services, then calibration width ADF and calibrate as on-screen instructions.

  (5) DON'T FORGET TO SAVE THE SETTINGS.

  (6) turn on the printer and remove trainer card and reconnect the hard drive.

  (7) once who did everything turn on the printer again, and everything should work without an error.

  Note: If you get the error when the cable step 3/4 remove scanner then plug back in.

  Fixed and working again.

  This can close close...

• HP LaserJet M1530 MFP: HP LaserJet M1530 MFP reinstall errors to 99%

  We are able to get printing to work, but what we want is that the scanner part work. I tried following the instructions posted in another post that we so that the software is installed, update the driver in Device Manager to use the HP LaserJet M1530 MFP PCL.

  There is also no in the same way, a lot of minutes sitting at 99%.

  Someone at - it of the other Councils, a 'solution' to reinstall the operating system.

  Thanks for providing this information @rbro.

  Yes, you can run the uninstaller from here. Make sure you unplug the USB cable first.

  Try the procedure described in this document for the 1618 error HP monofunctional and printers multifunctional - Fatal Error ' fatal error 1618' (MSI error 1618) displayed for HP Software Installation in Windows. .

  Please hold me. Thank you!

• LaserJet M1536dnf MFP: LaserJet M1536 don't not printing Mac laptop, all lit LEDs under LCD

  My LaserJet M1536 suddenly no longer print from my Mac laptop. And Yes, I downloaded the HP printer from the Mac App Store software was last updated.

  Under the LCD of the printer are three lights that stay on, even after that I power on and off the printer (the LEDs are green, the orange exclamation point and the orange point then). I don't know that the fact that all three LEDs remaining on the means, but it seems to be indicating a problem exists.

  Please help with advice to rectify or isolate the problem at least.  Thanks in advance.

  Do a google search, but the price will be high.  You can try a company call metrofuser.com because they can get a better price.  Good luck.

• HP Laserjet M1536dnf MFP / Installation on SP3 Win XP x 86

  After a long struggle and without success, I decided to post my problem here. During the installation of the drivers and scanning HP everything goes OK until step "Connect a device" appears. After several minutes to wait for a window with the fatal error message appear, indicating that the product may not be installed. Installation was cancelled. For installation, an original CD as well as the latest version of the drivers were used. The same result without success. In addition, troubleshooting of HP has been applied, which means that all startup applications and services with the exception of Windows services and applications have been disabled. Then after restarting a facility began with the same result. One last thing to add. During a connection device, Windows installs drivers. And the only available option is an impression (copy worked, of course, all the time). I would be grateful for the help, because no more only solutions.

  P.S., HP Print and doctor Scan has been tried. Scan test was chosen. The program has lead me to the HP support on the first try "pilot" sorry for the few grammar errors

  http://h30434.www3.HP.com/T5/printer-all-in-one-install-setup-e-g-Windows-8/Laser-Jet-1536-DNF-installation-problem/m-p/1087889#M43766

  I found this on a different post that addresses the same issue & point.  I tried on mine and it worked the first time.  Try it and give it the Kuddos.

• HP Laserjet M1217 MFP printer - error memory power

  I just install my new printer HP LaserJet M1217. I get the message "Power supply memory error" on the screen of the printer > installed the SW using the HP Smart Install program.  Win 7 is the operating system.

  Thank you very much for your help!

  Hi kongtoy,

  There is a clip on the chip on the cartridge's protective plastic. Remove the orange plastic, and he's going to quit giving you the power of memory error. Refer to figure 6

  Power supply memory error "Message is displayed on the control panel

  

• HP Color LaserJet M177fw MFP Scanner Error 22 Pro

  Bought this product today. 3. analysis later, 22 Scanner error. I have consulted the troubleshooting basic guide. Product unplugged for 15 seconds, no improvement. Updated firmware to update, no improvement. Very discouraging to buy something and it fail on me the same day... Help please.

  Thank you!

  I'm ready now. I returned the product to the retailer. Upgrading to a different model, and yes it's an HP. It was a much better option because HP would not have replaced my unit with another unit AGAIN, it would have been updated. I feel like a complete jerk to study does not comment on a product before buying it. HP has a very good line of printers, seems just that this model has had its problems.

  Thank you.

• HP LaserJet M1536dnf copy of the automatic document feeder

  HP LaserJet M1536dnf MFP

  FW version: 20130114

  I load the paper in tray and press copy ADF on the front panel button.

  Once this UPM retrieves the document, it crosses all the way to scan and UPM returns to ready state without printing anything.

  Copy in the same way to scan flat ends with a scanned copy of printing as usual.

  I suspect that the problem of Firmware.

  Any help?

  Hi, Jason
  I think you forgot to mention what buttons I have to hold in the power of the UFM.
  I did re-init procedure (hold right + Cancel when power on) and reflashed latest firmware. It did not help.

  If I do a search with the ADF, the printer tries to print anything. UPM simply returns to the ready state after the end of the analysis.

  Update:

  It seems that I fixed it.

  I did the procedure exactly as Jason suggested, but when I checked whether the problem is resolved, UPM did the same, scanned and returned to the ready state without printing anything.

  After that I did hard reset again, then immediately I did again the procedure to reset internal memory

  Spoiler (Highlight to read)

  (Turn off the UPM, press front panel and hold right + Cancel buttons, power on UPM during their detention, let them go after the LCD displays "init memory" and wait as UPM to ready state.)

• OfficeJet 6700 analysis via radio to 90% and then fails with an error of communication

  New HP Officejet 6700 Premium; no error during installation; -device not scan via radio: scan to ~ 90% with the visible image in the preview is when inaccessible window of the Scanner is returned with the error message "Scannner communication cannot be established.  Ensure that your product is turned on, check the connection... ».

  Dell Inspiron E1505 laptop. Vista; Trend Micro Titanium 2011 Dell

  1. Network wireless, print, fax work very well.
  2. Software has been uninstalled, cleaned and resintalled.
  3. Fixed IP address received.
  4. Windows drivers are the most common, HP device firmware is up-to-date.
  5. When the trend is disabled, scanning works completely.
  6. All scanning functions and work completely through USB with active trend.
  7. MS Paint scanning to the device wireless without problem with active trend.
  8. Ports below were opened in the Windows Firewall.

  TCP UDP
  137 137
  138
  139
  161

  427 427

  9100

  9220

  9500

  • Printing and scanning doctor works and ends when the trend is disabled.
  • Print and scan doctor hangs up on Scan Test and returns the same communication error window when the trend is activated but no further information or help.
  • Contacted Support of trend, which has provided information on how to create an exception in the product and advise him to: "... to add the file scanner to the program exceptions list."   Trend has been unable to give advice on what specific HP or the files to add to the exceptions list.
  • File by file, the following files have been added to the list of exceptions of trend without effect:

  C:\Program Imaging\devicemanagement\hpzscro1.exe HP

  C:\Program 6700\bin\HP Officejet HP Officejet 6700.exe

  "\HP Officejet 6700UI.dll.

  '\HPNetworkCommunicator.exe '.

  '\HPScan.exe '.

  '\HPScanDisco.exe '.

  ScanToPCActivation.exe

  ScanToPCActivtionUI.dll

  Toolbox.exe

  ToolboxUI.dll

  C:\Windows\twain_32\HP Officejet 6700\HPScanUI.dll

  '\Scanapp.ini '.

  '\hpxsTwain.ds '.

  • Device IP address correction has been added and listed as an exception in Web site.
  • Other computers are able to scan wireless unit.

  Are there other HP file or file windows called scanner of HP who participates in the scan Communication that must be added or tried?

  A short history:

  After spending 4 hours and countless computers, printer, router restarts, channel changes etc, on the phone with HP printer support, to solve this problem, I was called back to my firewall provider (Trend Micro) when the product is disables scan works. (Yes, it's the same question that I started.)  As you can imagine made me unhappy...? Since I had already made contact with them for advice on how to configure the product before posting here in the first place and, possibly, appellant assistance from the printer.

  The solution was finally trend had me to rename a file in the registry, which, I presume, caused the trend product regenerate a clean version of the file.  As trend firewall exceptions had already been saved, scan over wireless works now! I post the location of the file and registry name, unless you use the identical product etc. to modify your registry database is scary business.

  Naturally, because it was just going to be like that, scan network worked, but then the network printer showed offline and I couldn't online despite shooters evil etc.  In the end today I completely uninstalled the product and the resinstalled it and now everything works.  Hard to be too crazy about HP, when, notwithstanding this saga, HP was right to send back me the vendor of the firewall... everyone gets their turn in the barrel of the dysfunction of the technology, and it was mine.

  What a striped set incredibly complicated of technologies that we depend on.  Travis, thanks for your help and trying on it.

• Web JetAdmin and HP devices displays does not correctly

  HOSTS 10.3.8810 - we have moved to a new location (network managed by a different group) and our digital senders appear as hp_mgmt_printer_120 devices, and our CP4525s CLJ appears as CLJ 3700 s. Cannot show details for devices and manage them. You can add a device, a green success message "device found", but you can't do anything with them. They have the status of peripheral communication error, all fields appear as . The networking guys claim that they are not blocking snmp. I installed HOSTS on my Win7 x 86 box and on a x 64 server - same question W2K8R2. (on a network different I installed it on a win7 x 86 and it works fine, so I'm sure I'm not doing something stupid during installation)

  See the attachment to see what I mean

  Help!

  solution - FIPS should be killed.