HP Zbook Studio G3: error cd/dvd device driver missing

Similar Questions

• Error ""A required CD/DVD device driver is missing. " If you have a flash drive driver floppy disk, CD, DVD, or USB, please insert it now.

  OriginalTitle:lack drivers

  I change my ubuntu to Windows 7, but "A required CD/DVD device driver is missing. If you have a driver on floppy disk, CD, DVD, or USB flash drive, please insert it now. Note. If the windows installation media is in the drive, you can remove it for this step. "what I can do about it?

  Hello

  Are you able to boot to the Windows Vista operating system?

  Read the following article and see if that helps:

  Error: A required CD/DVD device driver is missing - when you boot Windows 7 or Windows Vista installation disk:

  http://support.Microsoft.com/kb/952951

• "A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVDm and USB flash drive, please insert it now. Roman Si the windows installation media is in the drive, you can remove it for this step. »

  When I try to install window 7 ultimate my Windows vista ultimate, the spectacle of the window the following error message "a required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVDm and USB flash drive, please insert it now. Roman Si the windows installation media is in the drive, you can remove it for this step. "I have the"TSSTcorp CDDVDW TS - L632H ATA Device"CD/DVD-ROM drive, and and it come preinstalled with no driver disk.  So is there a solution to the problem?

  You could try to copy the contents of the DVD to a folder on your hard drive. Then start the installation from there.

  (I've seen a post or two during the upgrade to Windows 7 64 bit of Vista 32 bit). Could just be a funky DVDROM drive problem. Copy of the files should ignore the issue.

  I hope this helps!

  Mark <> Microsoft Partner

• Impossible to re - install Windows Vista. "A required CD/DVD device driver is missing." appears

  I have the same problem as a previous applicant.  My hard drive went down and I had to replace it with a new one.  Windows Vista is the operating system installed on my HP Pavilion and I try to use reinstall drive.

  The message says "A required CD/DVD device driver is missing.  If you have a driver disk, CD, DVD, or USB flash drive, please insert it now. »

  I don't have a floppy drive on this machine, so I'll have to do the installation from a USB key.

  I tried so that it points to the Installation DVD, but it was still impossible to find the required driver.

  Thank you

  Sean

  Hey Thornwill

  HP machines have some problems with the replacement of their equipment with new hard disks not hp etc. and reinstall vista

  My advice to you would be that you contact hp

  Walter, the time zone traveller

• Portege A600 - Windows 7 installation CD/DVD device driver

  Hello.

  I am trying to install Windows 7 Professional 64 bit on my Portege A600.

  I tried to boot from the DVD, flash. I changed all of the possible settings in the BIOS, I have updated the BIOS to version 3.0, but I still have this bloody error "a required CD/DVD drive device driver is missing". Is there a place where I can download this driver to show the installer without having to download a 100 TB of pron?

  Or is there a way to fix my problem?

  Hello

  First of all there is no special driver CD/DVD. It of a part of Windows 7 and so there are no drivers available.

  It would be interesting to know when you get this error exactly.

  Maybe your defective CD/DVD drive. You can test another?

• Windows 7 cannot install from the cd/dvd-rw LG GH22NS90 player. "the CD/DVD device driver is missing" message is presented. How can I recognize the device?

  Separated from this thread.

  I have the same problem, my Windows email me the error code (19) of register incomplete or...
  I have download the drivers from the web LG.com and he send me, devide cant find.

  I try, I try and without operation = s help to respect? THX

  Hello Hendry,

  Thanks for posting your query in Microsoft Community.

  I understand that you have any questions using the CD/DVD drive in Windows 7 computer. We will certainly help you with the same.

  I would like to know some more information on this issue to help you better.

  1. Are you able to access the other CD/DVD drive in Windows?
  2. You try to install the drivers for any device?
  3. When say "Windows send me error code (19)", you get this error message in Device Manager?

  In the meantime, please follow the below suggestion to solve the problem.

  The error code 19 occurs when data in the registry for the device and its driver were damaged.

  For more information on this error, follow the link below:

  Code 19: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged

  () Also applies to Windows 7 as well ()

  http://TechNet.Microsoft.com/en-us/library/cc772156 (v = WS.10) .aspx

  Additional information:

  Your CD-ROM or DVD drive is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about the back upward and restore the registriesry, click on the number below to view the article in the Microsoft Knowledge Base:

  Registry backup
  http://Windows.Microsoft.com/en-GB/Windows/back-up-registry#1TC=Windows-7

  I hope this helps. Otherwise, feel free to write us again for more assistance, and we will be happy to help you come.

• Equium A60-157: error caused by device driver

  Hi all

  I try to write my thesis at the moment and am hampered by my laptop! It keeps randomly, which brings to the top of the blue screen of death, then by restarting; When everything is loaded to the top, I get a "serious error" message that says "error caused by the device driver. As far as I know, all the programs I have are compatible... I was advised to restore the factory settings, which I did a few months ago. And I got the BIOS update for my computer. But it is always the case!

  If it helps, the programs I use daily are Microsoft Word, Access, Powerpoint, Internet Explorer and MSN Messenger. I do not run any games high spec (only Minesweeper occasionally!)

  What can I do? Does anyone else have this problem? Any advice would be much appreciated, because these accidents do not help us to my work!

  Thank you...

  Hello

  It's not easy to tell which device is causing the error.
  What you can do is to check the device drivers. Visit the page of the Toshiba driver and check if there is a new version of driver for example graphic driver.

  Also sometimes this error message appears if the module of memory is faulty.

  What you can do is to use the Microsoft Online Crash Analysis.
  Maybe if you can identify this evil s.
  http://www.Microsoft.com/windowsxp/using/Setup/expert/northrup_03october06.mspx

  Good luck

• dc7800 sff windows 7 32-bit clean install - a required CD/DVD device driver is missing.

  Hard to install Windows 7 32 bit on my desktop DC7800 SFF pc

  white screen - fixed (updated bios using back win98 & USB flash drive prep utility)

  installation white screen set (stopped using the dvd usb player & utilisΘ local DVD drive)

  Image DVD transferred to USB flash drive (always get this request)

  Downloaded and tried many drivers of different sites...

  Drivers, Software & Firmware for HP Compaq dc7800 Small Form Factor PC

  Intel® Rapid Storage Technology (Intel® RST) RAID driver

  Intel ICH9 Chipset Driver for Microsoft Windows 7 - sp46869.exe

  It seems that nothing I try does not work.

  (always get this request for drivers)

  It has been a very long and tedious struggle day. I'm very tired and don't know where to look next to find answers...

  Any help this dispute would be really appreciated thanks.

  Well everything is solved and works well.

  Typing this from the newly built Office.

  Any Solution used (thanks to Paul Tikkanen to put me on the right track)

  (01)

  Update BIOS to fix a blank (black) screen during windows 7 Pro (32 bit) install on a hard drive (new & empty).

  Dc7800 SFF - Windows 7 drivers

  Update of firmware for HP 786F BIOS of computers with Intel processors families
  sp51245.exe

  I couldn't get this utility bootable CD version to work so had to turn to a USB bootable flash instead.

  Prepared the botable USB using - key USB W98 back Starter Kit

  (02)

  Downloaded the ISO from Microsoft file

  Windows 7 Professional with SP1 (32-bit)

  SW_DVD5_Win_Pro_7w_SP1_32BIT_English_-2_MLF_X17-59276. ISO
  Real Corsair Flash drive size - 2 377 506 KB - in windows Explorer
  Size: 2.26 GB - 2,434,566,144 bytes
  Size on disk: 2.26 GB - 2,434,596,864 bytes

  The file ISO of Windows 7 original instalation was certainly smaller that it should have been!

  (03)

  Burn the ISO on a 4.0 GB Corsair Flash drive using USB W7 Starter Kit

  New image details - Corsair 4 GB Flash Drive
  Size: 2.28 GB - 2,452,486,680 bytes
  Size on disk: 2.28 GB - 2,454,302,720 bytes
  873 files
  200 files

  (04)

  The installation went very well with only 2 issues of device driver initially...

  PCI Simple Communication controller
  Driver - Chipset
         Customer Manager Active Intel HECI Device Driver
  sp46137.exe
  PCI serial port
  Software - system management
          Intel AMT AMT 3.0 LMS_SOL
  sp46134.exe

  (05)

  I run one - SAPPHIRE HD 5450 1 GB DDR3 PCIE HDMI - Twin (DVI & VGA) graphics card

  First configuration - downloaded the drivers from the manufacturers Web site.

  On the installation of what I thought was the at and the latest driver, 2 problems...

  1 - the installation says that I needed .net Dot 4

  Downloaded and installed - Microsoft .NET Framework 4 (stand-alone Setup program)

  2 - the second test video driver installation is finished - but - screens flickered and flashed like crazy.

  I did correct anything that.

  Wiped the hard drive and run through the steps above.

  This time, making sure to use the original cd that came with the card of 2011. Result!

  PS - In the first leg through after installing windows successfully, I did all the updates of Windows 7.

  It took hours to download and install.

  Second time, I did not bother with the Windows updates immediately.

  Next step-

  3 future issues to be covered in the following threads

  (a) preparation of the utility of the technology Intel Management Acive - entirely private or disabled.

  (Do not need or want but hate having outstanding pilot flags in Device Manager).

  (b) the image of the hard drive and train you to restore boot partitions for multiboot Windows 7 installation.

  (c) work on a quick way to landslide-live stream the latest windows updates in the installation.

  Thanks for the help and I hope that some info above is useful.

  Advice on the high road (preferably free) partition SW of imagery to manage encrypted data of the partitions would be a good thing.

  Next thread?

• Error installation software device driver for removable devices in Windows Vista x 64

  I have Windows Vista x 64 installed on my PC and nVidia Forceware motherboard and graphic cards.

  When I plug in any removable drive into my USB 2.0 port, Windows starts the installation of the device driver software and then sees it as an unknown device. The dialog where he asks me if I want to 'locate and install driver software', 'Ask Me later' or 'don't show this message for this device.

  I select the recommended option: "locate and install driver software.

  I click 'Continue' when Windows asks me permission to continue.

  Then, when the execution of the installer of the software in the bottom right of my screen, the installation of driver software for device, it shows "unidentified device failed.

  Then another window pops up saying this:

  "Found New Hardware - device unknown".

  Windows encountered a problem installing the software driver for your device

  Windows found driver software for your device but encountered an error trying to install it.

  Kodak

  An error occurred during the installation of the device:

  The driver for this device is missing a necessary entry. Maybe it's because the file INF was written for Windows 95 or later. Contact your hardware vendor.

  If you know the manufacturer of your device, you can visit their website and check the support section for driver software. »

  That's what he does when I'm trying to connect my Kodak Easyshare M550 digital camera. I would go ahead and contact Kodak, but the problem seems to extend to ANY removable device on my computer.

  For example, I have a Lexar Flashdrive. When I plug it into my USB 2.0 port, it Windows says the following:

  "Windows needs to install driver software for your USB Flash Drive", etc...

  'Install the device driver software', 'USB Flash Drive search Windows Update'...

  Then a window opens asking me to "insert the disk that came with your USB key. Problem is that no driver disk not supplied with the hardware that Windows Vista is supposed to come with the drivers. I know this because the camera and usb flash drive worked very well until I reinstalled Windows Vista on my new hard drive (new installation, because my old hard drive crashed) and I've NEVER had to install device drivers for Windows to recognize it as a removable drive and operate automatically.

  Also, I installed Daemon Tools Lite and I had to manually "Update" the device driver to point to the "Windows\INF" folder in my hard drive, after copying the cdrom files needed for the specific subfolders for windows to let the program assign a drive letter for the drive virtual it creates.

  I think that perhaps not all device drivers have been installed when I installed Windows Vista, this time. If that's the problem, I don't know how that could happen, nor how to fix it, but I really prefer to find a way to solve this problem without reinstalling Windows Vista again. I don't mind not manually install the drivers as long as someone can show me what files to copy and where to find them on the Windows Vista disk that I bought at Microsoft. I KNOW that Windows HAS come with these drivers.

  If anyone knows how I can fix this, please tell me, because it's ridiculous to not be able to use any removable device readers (except for the use of all Flash drives). Thanks in advance.

  I know it can be frustrating to solve problems.

  (A) was this post or hibernation sleep?

  Microsofts troubleshooting KB

  http://support.Microsoft.com/kb/928631

  (B) the bios settings

  First of all you do not state if you tried to see if there was a setting in bios disabled USB ports during the startup. Or how the bios was set to install devices automatically. If you check your manual site or the motherboard manufacturer

  It will tell you which key to press. And where your USB ports are on or off. Some systems do not have to turn on or off.

  Plug n play OS on conscious

  could help Vista automatically recognize your USB

  (C) what version where do you use? SP1? or gold?

  (D) USB hubs may cause problems just be hubs. Power connected?

  (E) and of course if it is a case check connection in the right port. Return panel slide? plugged into port back?

  Hope something here helps

  Keith

• I have a Vista system and my cd/dvd device driver is corrupted or missing (Code 39).

  How can I recharge the device driver? Whenever I have to uninstall the driver and the system tries to install the driver, I get the message that is damaged or missing.  How to solve this?

  I tried deleting the cdrom.sys file in windows, but it won't let me even if I'm on the administrator account.

  I also tried driver uninstall with the installed drive and rebooting, but the corrupted message driver happens every time that I reboot.

  Is it possible that the drive itself is the problem?

  I'm ready to get an external cd/dvd drive.

  Try running the Fixit from here:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  "Or you can try the procedure in.
  Fix it myself

• error message this device driver has stopped responding, but recovered. What can I do to fix this?

  HP G72-b60US notebook

  Windows 7 Edition 64-bit family

  Intel graphics card

  I play a game and it's going very well for 10 minutes, then screen wil go black and trying to "fight" to override the game to bring up the office. then an error message is displayed to tell the device driver is not responding but recovered. I'm trying to get back into the game, but it doesn't allow me not-screen remains black when I try to turn on or off. so I have to ctrl-alt-del to bring up the Task Manager to stop the game. Then, the computer and the graphics card works fine. I tried to see if the driver for the graphics card needs update but the CV Wizard and windows update tells me that everything is fine. Help?

  Thank you.

  Angie

  Hello

  A.

  Check that your laptop is overheating or not.

  To do this use HWMonitor (free and recommended).

  If it detects overheating, consult this guide.

  B.

  Update the Bios.

  The update of the Bios?

  
  

  Download the last update of the Bios here.

  Connect the power adapter to the netbook.

  Disconnect from the Internet. Close all running programs. Disable anti-virus and firewall.

  Double-click the Bios update exe file. It may take some time, so it is important to remain patient, not to interrupt the process. Allow the laptop to restart after applying the BIOS update.

  Although this update is running are not:

  • Turn off your laptop,
  • Disconnect the power adapter,
  • try to run any software or do anything thereon.

  Note:

  The Bios update process is always risky. You do this at your own risk.

  C.

  Update the graphics driver.

  Uninstall the Intel graphics driver.

  Resources:
  Uninstall software in Windows 7

  Uninstall or change a program in Windows 7

  Download and install the latest driver from here.

• DVD device driver is missing

  When installing Windows 7 from a DVD, after loading files, it asks a missing device driver. How can I live without these hassles?

  Ways in your installation media are damaged or corrupted. Try to download a new copy.

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

• Windows 7: A cd to dvd device driver I'm missing?

  Excuse me..

  I have problem with win7, the problem is that after the victory to Flash successfully make my bootable flashdisk, then I plug the flashdisk on my 110-3500 HpMini, but after starting Setup win7, a box pops - up and theres something written there that "a required cd/dvd drive device is missing... blah blah..." Is there something wrong with my HpMini? I tried to cancel the program installation and then re insert it to another usb port, but it did not work... Please help me sir... Sorry for my bad English...

  The wireless switch is on the front on the right side in the opposite of the power switch position.

  Windows Dvd installers are much more likely to become corrupt than ISO files or installers of USB. They are not indestructible and are best kept in a DVD box for safekeping.  All it takes is a simple scratch on the label of the DVD side and toast.

  Disc info you provided are identified as a Western Digital Scorpio Black SATA2 320 GB hard drive. What is the product number and the name of the product of your mini?

  Best regards
  ERICO

• Cannot install windows 7-error: dvd/cd driver missing

  Try to install Windows 7 on a different SSD, but get an error indicating that the missing required cd/dvd driver.  How Windows load into memory from a cd/dvd that windows 7 says there is no driver missing?  This is the same installation disc that I used on a previous SSD without problem.  I have 2 other unused installation floppies, and each returns the error message.  This problem arose when an attempt to use System Restore Image I had done just on an external SSD and a drive hard usb.  The error I had to try to use one of them was that the Image was made in EFI and the computer seeks to restore in BIOS. It's the same machine.  Yes, disk management displays the UEFI 100 MB system partition.  The motherboard is an Asus F2A85 - V Pro.  List Disk running installation diisk sees only the cd/dvd and the drive hard usb but not the SATA drives.  When you normally use that List Disk sees everything.  The UEFI bios sees all readers, when you use the system installation disk.  I used a system repair disc made from the same computer at the same time as the picture of the system and used to start and got a system repair options is not compatible with this version of windows.  The windows version is 6.1.7601 sp 1 build 7601.  Any ideas?

  Hello

  Thank you for your response.

  There are two modes of starting particularly machine-> BIOS & EFI. BIOS is the general start mechanism found in most machines. Some of the machines also support EFI boot mechanism with BIOS

  Either the BIOS or EFI is set as the default in your machine - Please check start the installation system which

  one is active by default.

  If the EFI operating system is installed, it will create an EFI system partition in your machine. Installation of BIOS has no EFI partition.

  Warning in the BIOS: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful. Please feel free to post in the case where you are facing other problems with Windows, we will be happy to help you.

• Error message: the device driver not available and impossible to send files from windows 7 Ultimate x 64 for Sony Xperia phone.

  Hello

  I'm unable to send the file with my laptop running windows 7 Ultimate x 64 on my phone (sony xperia with android os p)

  I can send the file to my phone to laptop and my laptop to another device and any other device for laptop .when I have associated my phone to laptop, I get notification this device driver is not available. my windows is updated and I installed the version lastes my bluetooth of the BT and my laptop even factory plant i tride to update my BT driver automatically from the internet but it doesn't work and I still have this problem please help me how can I solve this problem thank

  Hello

  This error can occur if you do not have an installed device driver or if you have an obsolete device for your Bluetooth device driver

  We can refer to the article and check if it helps.

  Error: "device driver Bluetooth not found" when you try to connect to a bluetooth device

  Try to re - connect the phone and try to install PC companion Sony support and check if it helps.

  PC Companion

  Hope the helps of information.