HP3630: Impressions of automatic test

Hello. I recently bought a HP3630 and every time it is automatically put on it print a test sheet, waste of paper and ink unneccesarily. Is there a way to stop this? Thank you.

The page is a page of alignment.  It allows to print once after a cartridge is changed if the alignment is complete. See here for more information, step 2 shows how to complete the alignment process.  This must be done shortly after the page prints.

Tags: HP Printers

Similar Questions

  • HP PSC 1500 works only when I print the first automatic test.

    Hi Forum

    HP PSC 1500 all-in-one printer was working fine until I tried to print an email from a friend of his Yahoo email account. Hot flashes "check it out seeing the print cartridge" and it will not print.

    I discovered that I can print a page of any document that is not related to the original email account, as much as I first print a self-evaluation report. The light then it will start to Flash, and I need to print another automatic test before printing another page.

    I use Windows Vista.  Thank you in advance.

    Thank you for taking the time and effort to respond to two people. After trying everything that was proposed without success, I discovered a piece of something behind one of the cartridges. I replaced since the printer. Thanks again to all.

  • Any simple way to automatic test of FPGA card?

    I'm looking to create a simple self-test for a 1042 q populated in LabVIEW PXI chassis. The VI DAQmx Test auto works for most of the cards, but card 7853R FPGA is also present in the system. I wonder if anyone is aware of any simple way to perform a self-test on this map?

    It is not a built-in simple only for a self-test card FPGA as there is a standard DAQmx map. The reason for this is that DAQmx self test accesses the firmware of the card and performs some basic checks here. There is no such firmware on the FPGA card because the FPGA card allows you to build your own underlying software for a device.

    If you want to check on good communication with the FPGA chip, you can try to compile a white VI to the chip. If you need the functionality of IO control you will have to put some basic features in VI, but it shouldn't take a lot of time development.

  • Rearmament and automatic test of a controller (not the instruments attached to it!) GPIB card

    We have a Council NI GPIB in an operation of great trial.  Because reliability is absolutely crucial, I want to be able to force a reset of the GPIB controller card, but also run a set of diagnostic self-test on the Board of Directors.  Note!  I does not reset the instruments attached to the GPIB bus.  I want to be able to reset the card controller itself and run automated tests on it.

    I studied literature, but all I find are commands to reset instruments attached to the Commission.

    Is there a test suit for the GPIB card and a way to reset?

    -Carl Dreher


  • Downloaded assistant and automatic testing has not begun.

    Downloaded the wizard.  The software element 11 don't have not installed automatically.  Where can I find?  If it is not called 'Adobe Photoshop Elements 11' what's his name?

    Direct download links for Adobe software

    Mylenium

  • Automatic test?

    Hi-

    I just signed up to the copy of the Master CS6 Collection. The other day a trail 30 days of creative cloud appeared in the "Plans and products" on my account. I don't want it now, but is more likely at some point in the future. If it is not removed from my account now, it will appear that I already used it up to

    I ABSOLUTELY, POSITIVELY, has not signed to the top so that it doesn't matter where... Why it appeared?

    I spend a long time on that customer service and they said that they could not respond, it might be answered in the forums section.

    Thanks for your help!

    NIck

    - - - - -

    The trial is incorporated into the account, it will start the day you begin to use it to download & install, just the presence of the CC icon does not mean that the trial has begun.

    Hope it answers your question, the icon can not be removed.

    Concerning

    Baudier

  • PXI-5404 or test automatic function

    Hello

    In my implementation, I use two frequency generators OR pxi-5404 and OR pxi-5412. I work with LabWindows/CVI 8.5. I have install the driver of the BCI to instrument (niFgen.lib rev 2.5.1).

    I encountered a problem with the function of automatic test of this driver. The automatic test in my program function has the following form: niFgen_self_test (Manager, & self_test_result, self_test_message);

    When this function is executed for pxi-5412 is no problem at all. The self_test_result is zero 0 and self_test_message is the string "Self last.

    However, if I use this feature for pxi-5404, a problem occurs. It seems that this function doesn't work at all for this instrument. The self_test_message string is always NULL and the self_test_result variable takes values quite accidentally which means that this function does not return anything. The instrument does not appear to have any problem. The other functions of the library, work very well. I also did a manual than MAX self-test (right click DeviceName) and the result was "the aircraft spent the self-test.

    This function is not compatible with this instrument (pxi-5404)? There is another function of low level that can perform the self-test?

    Thanks in advance,

    George

    OK, I agree with you.

    Thank you

    George

  • Satellite A300-1QD - start some time and memory errors won't test

    Hello

    I have some real problems with a brand new satellite A300 1QD.
    After update of Windows Vista Home Premium 64-bit (Service Pack2) Vista unbootable. After the reboot of forst, it showed a message:

    File: \windows\system32\winload.exe
    Status: 0xc0000221
    Info: the file is corupt possibaly. the header checksum does not match the checksum calculated.

    AprΦs the dΘmarrage of the original CD Vista Home Premium or the Systembuilder OEM another error appeared:

    Error: 0xc000000f
    Missing or damaged \Windows\system32\winload.exe

    Does not even work by pressing F8 during startup. I have a chance to start even a repair because there is no option that I could choose.

    After a few resets the A300 seems to have some problems.
    A few times the display does not start, after the other it does not, start by hanging up during the automatic test etc.
    I have reset the BIOS by default Options, but it does not help.

    The A300 are one week. Am I allowed to remove a RAM bar without losing the warranty?
    I have read that sometimes it helps. I was able to do a memtest software vista. It is said that some hardware conflicts appeared.

    I am desprate, please help.

    EDIT:
    I did another test memory with linux 64 bit (openSUSE 11.1) and many erros occurred.
    What can I do now? The laptop is a present fpr my girlfriend Monday 15. Can I order other RAM and return that broke with a Numbor RMA or something?

    EDIT2:
    I recognized, that sometimes, when I start the laptop, the power led is the lightning to the top, but the satellite logo in the left corner remains dark.

    Oh, by the way, excuse my English, I hope that I can make myself clear enough that you can help me ^^

    I guess that you have solved this issue thank you for your comments mate!

  • PCI-5922 self-test error-223431

    I try to reset PCI-5922 OR MAX and get the error code 80040383:

    "There was a problem of resetting the device."

    Then I try the automatic test of NOR-MAX and get the State Code:-223431

    "The self test failed.

    State code:-223431

    Internal software error has occurred in the extended software. Please contact National Instruments. »

    I have tried following th:

    1. reboot the computer

    2. Uninstall and reinstall OR-Scope 15.1.1

    3. change of PCI slot

    After a few tries it turns out that the problem was in the computer. When it is installed in a different computer, the PCI-5922 worked properly.

    Now, it seems obvious: when troubleshooting

    1.) install the Board in another computer

    2.) install another identical sign (if you have one) in computer suspiciuous

    Yonathan

  • myDAQ new installation self-test fails 88705

    "' Problem: NEITHER myDAQ"myDAQ1"- Measurement & Automation Explorer-online devices and Interfaces-online OR myDAQ" myDAQ1 "-online self-test does not work. The error message is "the self-test. has failed. -88705 the specified device is missing... »

    My environment:

    8.1 Windows 64 bit running under Oracle VirtualBox Version 4.3.20 running Mac OS x on a MacBook Pro 2012 10.10.1. I have no prior exposure to work with myDAQ, LabView, or any tool of NOR.

    I downloaded NIELVIS1400_downloader.exe for Windows 8.1 to ni.com and it is finished.

    During installation I secured guarded against the problems of Win8FastStartup by stopping and restarting the PC when asked.

    After the installation when I plugged it physically in the myDAQ device, it was recognized by Windows 8.1 because Device Manager has the 'data acquisition' entries under which "NEITHER myDAQ" appears. For NEITHER myDAQ device status is 'this device is functioning.

    When the myDAQ was physically connected, the window "NI ELVISmx Instrument Launcher" popped up. I clicked on the icon 'How to set up your hardware' and the 'get started Guide... "pop up. I checked the blue LED on the device came and it is stable on. I went to "2. Paragraph confirms the recognition of the devices"in implementing on the way, guide and follow the instructions to start the automatic test. There not as described above.

    I noticed similar problems have been reported in the past. Closest to my problem reported by flex11 on 05/05/2014. Reading through I don't see any resolution itself. Another similar problem was solved by manually starting the service 'NOR device charger '. In my case, this service is already running. "NO license server" is the only service stopped, but I guess that's normal for myDAQ.

    I don't have any other product OR installed on the PC.

    I'm sure there is a simple solution to this problem, but I'm afraid it's escape. I'd appreciate any help I can get through this forum.

    Thanks for getting back to me. Your answer gave me stamina I had to move forward.

    I installed http://www.ni.com/download/ni-daqmx-14.2/5046/en/ and finally managed to do work. The exact boot sequence I need is:

    (1) delete myDAQ by USB port and then start Windows 8.1 under VirtualBox.

    (2) after that Windows 8.1 will appear, fix myDAQ on a USB port. If a pop-up window appears asking you to respond, ignore (at the beginning I did not ignore it and myDAQ transformed into a charger USB device firmware such as reported by Device Manager).

    (3) at this stage most likely "VirtualBox VM features-online USB Devices" drop-down menu shows "National Instruments NI myDAQ [0003]" as an entry but without a check mark to the left of the name. Bring the cursor to the left of the name and click here. You should now see a check mark there.

    (4) my myDAQ Self tests started working.

    However, I need the functionality provided by ELVIS as well. So I uninstalled http://www.ni.com/download/ni-daqmx-14.2/5046/en/ and installed from NI ELVISmx 14.0. My boot sequence that I have reported above, didn't work. Just at the moment it's just happened that Oracle has released Version 4.22 of VirtualBox that I wanted to try and ELVIS started to run. I can now use myDAQ DMM.

    One thing that contributed to my problems is fruitless attempts to uninstall the software OR. Unsuccessful uninstalls leave garbage behind who can or cannot cause problems in subsequent relocations. In one case, I'm done with the nidevldu (OR charger) service stuck in the system. I had to do a reset Windows 8.1 recovery operation to get rid of him. I decided to restart Windows 8.1 before uninstalling the software. This ensures that there is nothing in the limbo that past can interfere with a successful uninstallation.

  • the automatic check after the pulse camera image

    Dear Sir.

    I made a request to acquire a picture after an external trigger (from the light source) and after a short delay (1ms)

    I use the Point of the camera gray grasshopper3 gs3-u3-51s5m.

    The problem is I want to save my images in a folder called 'Images' with the name ' automatically test 0 "and if it exists already name it" Test 1 "and so on... '".

    But can't really find a way to do it.

    Hope you can help out me.

    Thank you very much!

    Chen.

    I forgot about the extension of the new... Apology.

    Here's who should work. I replaced the game model vi with the channel scan. Error compensation is where there are files of othter, which does not meet the model schema

  • Run unit tests different projects

    Hello

    I would like to start automatically tests in several projects.

    Here's the scenario: given A, B, C,... independently developed projects and say the developer has introduced an amendment that affects the B and C and maybe other projects too. now, I would like to re - run all unit tests in A, B, C,... to see if the change results in errors in B, C, or any other project.

    I thought to create a master project containing all the tests of A, B, C,... in auto-complete files but: 1) auto-complete files must be added manually and I would have a general solution; (2) auto fill records appear to be buggy or at least that they do is refresh as expected; in any case, 1) already is a show-stopper.

    LabVIEW can be script? Other solutions?

    Thank you

    Peter

    Peter,

    P@Anand referred to in the screw of the API of the UTF... You can use them to load unit tests and run independently of the project.

    Norbert

  • ERROR-235140 SMU-4139 self-test

    Hello

    I get an error with my SMU-4139 module. I have a chassis SMU-1075 configured with 2 NI PXI-4070, NI SMU-4139 2 modules and 3 NI PXI-4130 modules.

    When I start my computer, a SMU-4139 module lights up with green and active green access light. The other SMU-4139 module will turn - on the same path, but in a short time, access turns off the light and the light turns red. I tried to run the automatic test NI Max, but I get this message.

    The test failed.
    -235140
    Internal hardware error occurred in Power_Supply material. Please contact the support of National Instruments.

    I tried to change its slot SMU, but I got the same error. Should I send this card in Checkout?

    Thanks a bunch!

    Hey,.

    I wanted to give an update about it. I uninstalled OR-DCPower (I think I got the version installed 1.9) and installed NOR-DCPower version 14.1. Everything works very well.

  • How to change the "Failed" result State after the test of "success."

    We do a picture of a LCD screen and watch if his work of all. Sometimes, the LCD is good work but the step failed. Where automatic LCD test fails show us the image of the camera to the user and it can decide if the LCD for success or failure. So when the user decides that the screen is good job we have to crush the status of the automatic test demonstrating lcd screen test passed in the report and the database. I tried with

    RunState.SequenceFile.Data.Seq ["Check_LCD_V3-0"]. Hand [' 154 Execute - all horizontal Segments on "]. Result.Status = "Passed",
    RunState.SequenceFile.Data.Seq ["Check_LCD_V3-0"]. Hand [' 154 Execute - all horizontal Segments on "]. Result.PassFail = "True",

    But in the basis of the status of this step is always 'impossible '.

    What I've done wrong?

    Thank you

    Alteschwed wrote:

    We do a picture of a LCD screen and watch if his work of all. Sometimes, the LCD is good work but the step failed. Where automatic LCD test fails show us the image of the camera to the user and it can decide if the LCD for success or failure. So when the user decides that the screen is good job we have to crush the status of the automatic test demonstrating lcd screen test passed in the report and the database. I tried with

    RunState.SequenceFile.Data.Seq ["Check_LCD_V3-0"]. Hand [' 154 Execute - all horizontal Segments on "]. Result.Status = "Passed",
    RunState.SequenceFile.Data.Seq ["Check_LCD_V3-0"]. Hand [' 154 Execute - all horizontal Segments on "]. Result.PassFail = "True",

    But in the basis of the status of this step is always 'impossible '.

    What I've done wrong?

    Thank you

    I recommend the following:

    (1) that the display automatically to test an Action step rather than a step for success/failure and set to square one local variable to see if the LCD self-test failed (for example Locals.AutomatedLCDFailed).

    (2) create a new test pass/fail (using the no adapter) that takes both the variable local and entry of the user account to determine it is the condition for success/failure (for example to set the data source of the step to an expression like:!) () Locals.AutomatedLCDTestFailed & Locals.UserLCDTestFailed)

    As an alternative to do 1) a step of the Action you can leave a step for success/failure and clear step on it to "step failure causes failure of sequence. You can then use the status of this step instead of Locals.AutomatedLCDTestFailed. The only difference is that the automated test will always be displayed as failed in your report, although the sequence can still be passed. It is somewhat a matter of preference.

    Hope this helps,

    -Doug

  • MAX self test is not available for the 9237 module

    I had been successfully using a VB.NET program to control the ENET-9237 module to read a load cell.

    I've been using 9.4 DAQmx drivers.

    Things were working well for months...

    Today when I tried to use it, I couldn't communicate with the device.  When I looked in MAX and ran the self-test I got an error indicating that the device is not active.

    I deleted the network device and it still added.  He added just fine and I can see the system state is in place, but now the self-test button is gray.  I can not even use my software to connect to the device.  So the ethenet part seems OK, but I can't get access to the real load cell module.

    This indicates a hardware failure of the 9237 module?  Or is there still something in the software I should try?

    It turns out that it was a software problem.  I moved the material to another computer and automatic test worked fine.

    I've uninstalled and reinstalled the DAQmx v9.4 drivers on the computer with a problem.

    Now everything works as it should.

    Not sure what was wrong with the original installation...

Maybe you are looking for