I can't get the update of windows to run. I get an error message that says that the update service does not work and I have to restart my computer.

Similar Questions

• Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer

  My computer stops the update via WIndows Update Component

  Whenever a try to do the manual update using this component I get the message;   * Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer *...

  My computer has a few updates, but can not run these update

  Whenever I try to run computer shotdown/updates remain frozen for a while and stops without updating

  He starts to run updates 1 of 13... and stops

  If I shutdown normal e, computer stay likehanging 1 hour without stopping.

  I would like to know how to solve this problem

  Thank you

  Concerning

  Gladmar.

  Hello

  Were there any changes made on the computer before the show?

  Perform the following methods and check:

  Method 1:

  I suggest you to check if you are able to access Windows Update service and ensure that the following services are started. If it is not started, follow these steps:

  a. click Start, type services.msc and press enter.
  b. search Windows Update.
  c. right-click on the service and select Properties.
  d. in type of startup, select enable.
  e. click Start under the Service status.
  f. click OK.
  g. Repeat steps c to f for the following services:

  Background Intelligent Transfer Service
  Cryptographic services

  If the steps do not help to solve the problem, you can go ahead with the methods mentioned below and check.

  Method 2:

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Method 3:

  Your anti-virus software is in conflict with Windows updates. You can test this by temporarily disabling your antivirus:

  Disable the antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 4:

  The problem with Microsoft Windows Update is not working

  http://support.Microsoft.com/mats/windows_update/

  See also:

  Troubleshoot problems with installing updates
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Updates: frequently asked questions

  
  http://Windows.Microsoft.com/en-us/Windows-Vista/updates-frequently-asked-questions

  I hope this helps.

• "The Windows update service does not work. Please restart your computer.

  If I click on "Check for Updates", a dialog box appears:

  "The Windows update service does not work. Please restart your computer.

  I rebooted several times, but the same error.
  Help, please.
  Thanks in advance.

  This site will help you get the update of Windows running service

  http://pcsupport.about.com/od/Windows-8/a/Windows-Update-settings-Windows-8.htm

• can't connect to my home internet income james ashley forgot it the link password does not work and the password I was given does not fit into the password box

  can't connect to my home internet income james ashley forgot it the link password does not work and the password I was given does not fit into the password box

  Are you sure that you do not have to register on this site through the usual way and what you should be used elsewhere on the site?

  Have you tried to contact them to help this topic or to check if they have a FAQ on this subject?

  I found this in another thread that you created [*]:

  I'm not sure do I bought a home income internet james ashley program and I copied the login info I was given and the password does not fit into the window of password and I forgot the link password does not work I sent emails, but do not receive an answer im don't know what to do is anyway you can help me to recover my info or help me change the password?

  I assume that you have downloaded and installed this program and need to use this password in this program or only you can use these data to download the program from the site james ashley?

• Connection problem: The DHCP service does not work.

  Original title: connection problem

  After got rid of a virus, my computer is always trying to get the network address. I found that the DHCP service does not work on my computer. How can I reinstall. I am running windows xp service pack 3

  Hello

  Follow these steps and check if they help.

  Step 1:

  Look for the DHCP Client service and DNS Client Services if they are started.

  a. Click Start.
  b. click on run and type Services.
  c. click right on - run as administrator.

  Check if the below mentioned services has mentioned State and type start.

  Client DHCP started Automatic\Manual.
  Client DNS started Automatic\Manual.

  Also check the dependency that are required for the DHCP Client services and DNS Client Service runs.

  To verify that double-click the service, and click the Dependencies tab.

  Step 2:

  I suggest you to reset TCP/IP settings to solve the problem.

  How to reset the Protocol Internet (TCP/IP)

• I just tried to install the Adobe Creative Cloud trail and the apps tab does not work and I tried to uninstall several times and nothing. Any suggestions?

  I just tried to install the Adobe Creative Cloud trail and the apps tab does not work and I tried to uninstall several times and nothing. Any suggestions?

  An error keeps poping up on creative cloud without work and it's really annoying that I can't use it anymore or even try anything at all.

  Help, please

  Using creative cloud | Download error in the applications tab of Creative Cloud Desktop Application

• Windows Server Update service does not work after the installation of KB2720211

  I have a Server 2008 SP1 32-bit Standard, which had the role of Server Update for the Windows software installed connected to a WSUS upstream server and everything worked, with 17 clients connected to him and get everything their approved patches.  It was a new server starting with WSUS added at this time 1 months ago.  He had to be upgraded to SP2 S2008 which I did and WSUS have continued to function.  After being on SP2, there was another 152 patches to be applied and after that WSUS does not work anymore.  It appears 1 patch that has been applied has been KB2720211 that seems to cause problems for a number of people.

  The problem is that the update service does not start.  An error message comes back that the service has not responded in a timely fashion and I can't find the log files anywhere on what it is.  Here is what has been done so far all that in the same issue:

  1 deleted WSUS and restarted and installed it again.

  2 Remove WSUS and Windows Internal Database, restarted and installed it again (using the download of KB972466).

  2.1 install SQL Management Studio and logged to an internal database SUSDB and checked it is not set to single user (I believe it is set for multiuser name but I'm going from memory)

  3. install the KB2720211.

  4. installation KB2734608

  5 remove WSUS and Windows Internal Database, restarted and installed it again (using the download of KB972466).

  I am looking for any information on how to solve what is the question, because there is nothing in the log files I can find and no event in the windows event viewer.  I am ready to start with the server however if there is something I can look at to possibly solve the problem, please let me know.

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Windows 7, update services does not work

  I have a problem to update software in windows 7.

  I have a HP G72 laptop.

  I replaced my hard drive. 350GB, Western Digital 750Go digital West.

  -J' made an image of the C partitie (if it is 3 months, installed for the recovery partition, new updated worked after that).

  The new disk hard there however any possible updates of windows. (the bar is red on the left).

  -After that, I reinstalled the original image when the laptop was new (DVD image). Same result on updates.

  -Remove the folders from the dir c/windows/SoftwareDistibution, no results.

  -Checked the status of services: windows update is statred and in automatic mode.

  N ' tried microsoft 'Fix - it' no results.

  -updated the drivers intel, no results.

  -Downloaded System Update Readiness of windows to resolve the error (Windows6 1 - KB982018 - v3 - x 64). When installing, I get the error 0xc8000247. So I'm not able to install this software.

  Looked after errors in the CBS.log newspaper: found M²: cannot read the time value RptTime from the registry. [HRESULT = 0 X 80070490 ERROR_NOT_FOUND]

  Do a clean boot, without result.

  Does anyone know a solution to this problem.

  Thank you.

  Ed.

  Windows 7, update services does not, RESOLVED.

  The problem occurs when you change your hard drive for a bigger, in my hard drive of the case a GB Western Digital 340 WD 750 GB drive hard.

  For the Windows automatic updates again you need update the Intel Rapid Storage Technology Driverdriver. It will not be updated when you have intel check your drivers! For me, only the 9.5.6.1001 version worked. This driver can be found at http://support.hp.com/us-en/document/c02219204 .

  Versions available at https://downloadcenter.intel.com/SearchResult.aspx?lang=eng & ProductFamily = Software + Products & ProductLine = Chipset + Software & ProductProduct = Intel % c2% ae + Rapid + Storage + Technology + (Intel % c2% ae + RST) did not work for me (I tried the form version 12.8.0.106 08/08/2013.) Why does not the superior version is not clear to me.

  Good luck to solve you yours it took me two weeks to find it.

  Ed.

• 8024A 000 - Windows Update code does not work and "installing Windows could not configure Windows to run on a hardware on this computer" for Vista64 reinstall

  I have a HP Pavilion Elite e9180t PC comes with Vista Home Premium 64-bit.  I had the hard drive (Seagate/Barracuda 7200, 750GB) SATA to go over me (after the expiration of the warranty of course) so I replaced it with a WD Caviar Green 1 TB drive.  When I rebooted the news of recovery disk to the new disk, VIsta worked but Windows Update does not work and I get A 8024, 000 error Code.  To worked with Microsoft to try to resolve that (never made), I am frustrated and all saved just reinstall Vista.  When I try to reinstall Vista, I now get the message "installing Windows could not configure Windows to run on a hardware on this computer."  The installation progresses up to the stage of upgrade (a final) then I get error and it puts everything back the way I started.

  The only thing I changed hardware wise is the hard drive, so this error message seems silly because Windows runs on this material.  I even double checked that Vista is always enabled.  Anyone out there have any ideas?

  I have a HP Pavilion Elite e9180t PC comes with Vista Home Premium 64-bit.  I had the hard drive (Seagate/Barracuda 7200, 750GB) SATA to go over me (after the expiration of the warranty of course) so I replaced it with a WD Caviar Green 1 TB drive.  When I rebooted the news of recovery disk to the new disk, VIsta worked but Windows Update does not work and I get A 8024, 000 error Code.  To worked with Microsoft to try to resolve that (never made), I am frustrated and all saved just reinstall Vista.  When I try to reinstall Vista, I now get the message "installing Windows could not configure Windows to run on a hardware on this computer."  The installation progresses up to the stage of upgrade (a final) then I get error and it puts everything back the way I started.

  The only thing I changed hardware wise is the hard drive, so this error message seems silly because Windows runs on this material.  I even double checked that Vista is always enabled.  Anyone out there have any ideas?

  Hey GMPete

  some posters have reported problems when replacing a drive hp etc. with a hp motherboard not provided player etc.

  I suggest tha contact you hp because it's their recovery process you use

  at the below link HP support forums

  http://h30434.www3.HP.com/

  link below is for direct hp support contact us

  http://welcome.HP.com/country/us/en/contact_us.html

  Walter, the time zone traveller

• What should I do if the wireless radio does not work and cannot connect to the wireless router?

  What should I do if, during the installation of my c309a Photosmart Premium printer all in one, which I am trying to install a wireless connection, I get an error message that the wireless radio is not working?

  Solved by turning the radio off and then on new wireless.

• When I enter a Web site in the url of the Enter key does not work. I have to click on the arrow at the end of the line. Is this a configuration problem?

  The Enter key does not work in the line of the URL. If I go says:
  www.Bing.com
  and then press the Enter key, nothing happens.
  I have to click the arrow at the end of the field in order to activate the link.
  If I am anywhere else on any page the Enter key works as it should.

  Please click the button of resolved next to the answer that solved your problem of Firefox support, when you are connected.

• HP G71-449WM. Windows 7 64-bit. "The audio service does not work.

  I downloaded all the updates that I can find anywhere. My roommate has deletion of things on my laptop for 'performance' and now I have no sound. I go to my device manager in the computer and it is says my IDT HD audio CODEC works correctly. And my Intel(r) High Definition Audio HDMI does not work correctly. What should I do to get his new? The the small speaker in the far right of the task bar icon has an X on it, as she was mute. BUT it's not. Help? /

  Hello

  Open windows control panel, open administrative tools, and then open Services.  Verify that the following services are all displayed as status = started and the Startup Type = automatic

  Audio service

  Multimedia class Scheduler

  Windows Audio

  Windows Audio endpoint Builder

  Kind regards

  DP - K

• Why Windows Update service does not work on my computer?

  After a few months of not be used, my Toshiba Satellite L35 (Windows Vista Home Basic; Computer laptop Service Pack 2) can not access Microsoft Updates.  Whenever I try, I get a message "the service is not running" and tells me to restart, I did several times without success.  Norton 360, and Spybot, indicates no problems.

  It's like something has removed or disconnected from all the Windows Update process.  "Update history" produces a blank page.

  After a few months of not be used, my Toshiba Satellite L35 (Windows Vista Home Basic; Computer laptop Service Pack 2) can not access Microsoft Updates.  Whenever I try, I get a message "the service is not running" and tells me to restart, I did several times without success.  Norton 360, and Spybot, indicates no problems.

  It's like something has removed or disconnected from all the Windows Update process.  "Update history" produces a blank page.

  Suggestion 1: Get rid of Norton and Spybot Search and Destroy.  I do not recommend Norton/McAfee products, especially the suites (I recommend NO suites - simple is better.)  Spybot has been a good product, but a few years back, he just stopped doing as well.

  Suggestion 2 (cumulative, not necessarily independent - but maybe): cleaning of your Windows Update stuff...

  All the following items in the order shown - no matter what protection against that, you think you have.

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  • MalwareBytes (FREE)
  • SuperAntiSpyware (FREE)

  Remove anything they find. Reboot when necessary. (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  Reset.

  Now reset your Windows with this FixIt components update:
  How to reset the Windows Update components?

  Reset.

  Try to get updates.

  If it still does not work, try this...

  1. Start an elevated command prompt.
  2. Run the following commands pressing on enter after each line:
     
     net stop wuauserv
     CD %SystemRoot%\System32
     Ren C:\Windows\SoftwareDistribution SoftwareDistribution.old
     net start wuauserv

  3. Reset
  4. Try to reinstall updates

  * Important * When you do this, the following problems occur:

  • Updates that are currently downloaded but which have not yet been installed must be downloaded again by using Windows Update or Microsoft Update.
  • When you remove the Software Distribution folder, your download history is deleted.
  • If you currently receive updates from Microsoft Update and Windows Update, you will need to reselect this option from the Windows Update Web site.

  
  * Note * if the problem is resolved and you can successfully download and install the updates, you can delete the directory SoftwareDistribution.old to recover disk space.

  STILL no?

  Use this FixIt:
  How to get the latest version of the Windows Update Agent

  Reset.

  Save components WU:

  1. Start an elevated command prompt.
  2. Run the following commands pressing on enter after each line:
     regsvr32 Jscript.dll
     regsvr32 c:\windows\system32\wuapi.dll
  
  regsvr32 c:\windows\system32\wuaueng.dll

  Reset.

  Try updates.

  If it still does not work after this - say parts of the former post once again (no need to conduct a new analysis of malware) from:

  "Now reset your Windows with this FixIt components update:

  ... but stopping at... «STILL no?'.»»

  Back - let everyone know what is happening.

• His record game. I can't play the sound. troubleshhoot does not work

  Next to my changer volume, there is a small 'X '. When I go over it with my mouse, it says: "no speakers or headphones are connected ', but the speakers are integrated into my PC, so my monitor. Also, if I click it, it brings up to solve problems, but that does not work either! Any help is appreciated, I can't do that without sound on YouTube!

  Next to my changer volume, there is a small 'X '. When I go over it with my mouse, it says: "no speakers or headphones are connected ', but the speakers are integrated into my PC, so my monitor. Also, if I click it, it brings up to solve problems, but that does not work either! Any help is appreciated, I can't do that without sound on YouTube!

  Have you tried to uninstall and reinstall sound card driver? You may need to visit the manufacturer's Web site to download and install the latest sound card driver.

• When I write editorials and press ENTER, it does not work and I have to press the arrow to go. Also ctrl + enter for auto site full addressdoesn can't work.

  When I write a Web site address and press ENTER, it doesn't fit to the page and I have to press the arrow to go. Also ctrl + enter for the AutoComplete does not work the address of the site. Lately, I noticed this problem in 6 FF. I expect the upgrade to 4 FF will solve this problem, but he persists.
  Thank you

  This may be due to a problem with an add-on. To find out how to solve this to find out what is causing the problem, see https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes