I closed FF in my 2nd monitor, now it opens only, why?

Similar Questions

• Installed Windows 7 on gateway E4500 PC and now there is no Audio as well as does not recognize do not identify/2nd monitor

  Installed Windows 7, 32-bit on the new hard drive. Gateway PC E4500. Cannot get audio and does not identify/2nd monitor. Already used Windows XP. Works well when the drive with win XP is reinstalled. Is Windows 7 compatible with this PC?

  Original title: WINDOWS 7 installation, 2 numbers

  Hello

  There is a gateway E - 4500D and E-4500 s model.

  Enter the model number on the link:

  http://us.gateway.com/GW/en/us/content/drivers-downloads

  E - 4500D has been supported by the gateway and gateway provided drivers for Windows 2000 Pro and XP 32/64, Vista 32/64.

  E-4500 s is supported under XP 32/64 or vista 32/64

  No support or drivers for Windows 7 32 or 64 bit.

  You can try the Audio drivers for Vista; no warranty if.

  See you soon.

• connect a 2nd monitor in order to expand the workspace

  All the people who are sitting next to my wife to work hung a 2nd monitor at their consoles portable to give them the extra monitor space to work in. My wife now has a 2nd monitor and a cable which is necessary for the two screens can be connected at the same time - just as they are. They are all connected to the network at work.

  But how she has set up in Windows? No work can tell her what to do to implement. Please be as specific as possible non-tech in your answer, that is, do not assume that I don't know!

  "JeffDavis" wrote in message News: * e-mail address is removed from the privacy * .com...

  Sorry if my post has been in the wrong place. It is a portable Windows XP which is a HP Elite. So, what do we do?

  XP...  Make sure you have the same image on the computer laptop and external monitor by using the Fn + F toggle key that I mentioned in my previous post. Right-click on an empty area of the desktop.  Left click on properties.  Click the settings tab.  You should see two monitors.  Click on identify.  The external monitor should show that monitor 2.  Click on the representation of the screen on the screen.  You should see below just a checkbox to «Expand my screen...» ' check that, to ensure that the resolution above this area is compatible with the external monitor and OK outside.  You should now see the Office extended to the external monitor.  Windows can be slid toward the new monitor and used as an extension of the screen of the laptop.
   
  Let me know if this can help, or if you have any other questions.

• My 2nd monitor does not

  My 2nd monitor is completely black except for a travel box with "not optimum Mode, recommended Mode 1280 X 1024 with a?," I restarted my computer and checked the connection without change, can anyone help please?  It was working fine until I unplugged the cable to use laptop computer only, and then when I plugged back it it shows is no longer.  Any help would be greatly appreciated.

  Hello

  These should help:

  How to set up dual monitors in Windows 7
  http://www.online-tech-tips.com/Windows-7/How-to-Setup-dual-monitors-in-Windows-7/

  Two screens are better than one
  http://www.Microsoft.com/athome/organization/twomonitors.aspx

  Work and play better with multiple monitors
  http://Windows.Microsoft.com/en-us/Windows7/work-and-play-better-with-multiple-monitors

  Move windows between multiple monitors
  http://Windows.Microsoft.com/en-us/Windows7/move-Windows-between-multiple-monitors

  Multiple monitors: frequently asked questions.
  http://Windows.Microsoft.com/en-AU/Windows-Vista/multiple-monitors-frequently-asked-questions

  ==================================

  You may need to update your display and video driver

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Can I output the monitor program PremierePro CC (only) to a 2nd video screen?

  I already have (years) used PremierePro on an edition of PC system. At this time, I used a box of cards and small groups of Matrox - it was so easy to put in place a 2nd monitor to display the program output (only).

  I started using new PremierePro (CC version) but this time on an iMac 27 "retina 5 k (max for the ram, processors and graphics functionality). I'd quite like to discover the program output only (or at least mostly) on a 2nd 1080HD video monitor. Is it possible to do? With no junction box, I guess that this cannot be done. Is this fair?  I know I could set up an iMac HDMI output, but that would be out of the whole office. I just want to really take a power of video output (monitor of the program only) rather than the entire desktop. Is it some sort of break Thunderbolt to send with a HDMI or DVi connection, which can display only the monitor program (like those old buttons)?

  Of course the iMac screen 5 k and the video monitor will be quite different devices - so I can't really just the range double configuration screen. A 2nd screen Mac is expensive - and it would be another screen to the retina, 5 k.

  As background information, for now I'm only editing content 1080HD that thus the 2nd monitor should be consistent 1080HD. I have various computer and video monitors available if this configuration is possible. I'm not too concerned about the quality of the image in the 2nd monitor - its more about speed reading to check for sync and motion - changes especicailly when a customer sits the long side (and Yes, I hate too). The iMac 27' is a good size screen, but I'm edition multi channel animation graphics and pictures (no animated videos), it fills the screen fast enough. If I want to program a monitor window half-decent size, I am constantly scrolling and minimization / maximization of the channels that I can see detailed work areas easily.

  If I ask a stupid question here, please don't shoot me :-) As I have said for a while I used the PP, but now I use it everyday - so just going back to it.

  Thanks for reading - and advice you might have would be welcome.

  Thank you.

  Pete

  If all you need is a program-monitor output to a second monitor, woudn't integrated two-monitor process work? No, is not the release of calibrated equipment which is often sought for high range editing, but it works for most cases... just have a second monitor mounted on your card system and on the Preferences tab, select it as shown...

  

  Just make sure that your operating system 'sees' your normal monitor as a screen, and then they will appear in this dialog box as your operating system lists them. PrPro always default to sending the output of the program monitor to monitor 2.

  No box necessary engine... and many who have the outboard motor to run a high-end TV, also use it for their treatment of General works.

  Neil

• 2nd monitor problems with Photoshop CS4 and CC

  I'm on a quest to solve a problem with my second monitor when using Photoshop. When I hit F in photoshop to switch between display modes or when I Zoom in or out this happens:

  

  OK, well it is turned on its side, but you get the point. Until very recently, I used OS x 10.6.8 with Photoshop CS4 with no problems but ran into some problems with applications etc so I upgraded to Yosemite. That's when the problem started. In order to solve what I did a clean install of Mavericks in the hope that Yosemite was too new and that he had not brought bugs. Then I reinstalled CS4 there more this problem, but another problem just as boring. the profile for the 2nd monitor appears so desaturated and terrible that I can't use it to edit, despite several attempts to recalibrate.

  Out of curiosity I tried the trial of CC in Photoshop to see if the problem of mosaic has been fixed, but it wasn't. Right now looked at color, but mosaic problem. Here is the info on my computer:

  

  I changed in system preferences > energy saver > graphics for better quality, but nothing has changed. In Photoshop, I tried Preferences > performance > the GPU settings > advanced settings > changed in Basic drawing and that did not solve the problem either. Any ideas?

  10.10 MacOS still has a number of video driver bugs, some causing display corruption and others causing accidents.

  Apple is aware of these driver problems and work on solutions.

  Turning off the use of Photoshop GPU can help.

  But if you need the GPU features, you can return to a stable version of MacOS.

• FF always opens in 2nd monitor

  I have two monitors and sometimes to define my 2nd monitor as master during software testing. Go back to use my 1st primary monitor (using the display settings) I find FF does not take into account the changed value and will always open on the second monitor. Back to zero does not solve the problem. All other applications open in primary education.

  A way to solve this problem?

  If Firefox is maximized and then minimize the window and drag the window to the correct monitor and close Firefox to save the setting.

  After the reboot, you can maximize again.

• With the help of a 2nd monitor with HP ENVY bow 27-k009 TouchSmart all-in-One desktop PC

  I would use a 2nd monitor with my HP all-in-one, but I can't figure out how to do this.  Our it guy says it can be done by using a VGA cord DMI but it does not work.  An another computer guy told me to get a USB cord with a graphics driver and technology at Best Buy told me that it is not possible to use a 2nd monitor with this all-in-one specific.  Please let me know if it is possible and how I would go to do.

  Here are the specifications of your HP ENVY tilted 27-k009 TouchSmart all-in - One desktop PC. Based on the specifications, this model, is a video output any. The HDMI port on the side is strictly an ENTRY;

  

  3 HDMI input

  To connect your computer to an external monitor, you will need to buy an adapter USB-to-video, as EVGA UV plus + UV39 or many other cards on the market.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• the 2nd monitor resolution

  Hi all

  I'm working on an application that uses 2 monitors.

  I have a VI that measures the resolution of the screen.

  I want to know the 2nd monitor resolution.

  How can I get that?

  Thank you

  Ritesh

  You can use a property node application, the display value-> AllMonitors. Index of this with an array and ungroup the result. This will give you information on the limits of the screen. By subtracting from left, right and top to bottom. You can get the size of the screen.

• When closing a window shows end program now - ONLINENT. EXE

  When closing a window shows end program now - ONLINENT. EXE

  The Quick Heal people seems to think that they have a fix for ONLINENT. EXE, suspended on shutdown (from his assistance page):

  We recently launched a new version of Quick Heal for 2012.

  Considering the same problems faced by our customers, we made the necessary changes in our latest build. So that no any module Quick Heal won't take more time to end its process so that closure of the system. It will help you to quickly stop your system.

  So, please download the latest below link-
  http://www.Quickheal.com/builds.asp

  Reinstall your Quick Heal with the last configuration. You will not face the issue once again.

  Kind regards
  Amol Shelar. For more help, contact us on-
  Toll free number: 927-22-33-000
  Toll free number: 1800-233-3733

  If you use their firewall and the XP firewall at the same time, this could also be a problem.

  It is generally not a good idea to use two firewalls at the same time lest they are fighting among themselves.  Choose one or the other to use, but not both.  The XP firewall seems to do a good job.

• icon editor sneaks to the 2nd monitor

  A Windows XP installation with main monitor in portrait and secondary as the orientation is landscape.

  But in LabVIEW 2009, the icon editor always appears on the 2nd screen.  Most of the

  time as my 2nd monitor is turned off, but fortunately, I turned on the 2nd just discovered this behavior.

  Is there a configuration to ini file for the icon editor always appear on the main screen?

  Thanks in advance

  Hi odd_modem,

  have you looked into this group? You will find updates, that should solve your problem...

• I had checked "extend my desktop to this monitor". I have only 1 monitor though. Now the screen is empty. I rebooted the pc in the hope to go in safe mode but the screen remained blank.__How can I go back to single screen? __

  I had checked "extend my desktop to this monitor". I have only 1 monitor though. Now the screen is empty. I rebooted the pc in the hope to go in safe mode but the screen remains blank.
  How can I go back to single screen?

  Hi Bilipino,

  You have more than one display card? Try to connect your monitor to the another card and see if you can get the display.

  Reference: http://www.microsoft.com/windowsxp/using/setup/hwandprograms/monitors.mspx

  I hope this helps...

• Change the problem of direction of the cursor with new 2nd monitor

  original title: problem of direction of the cursor with new 2nd monitor

  I just added a 2nd monitor to my computer. The 2nd monitor is left of my laptop but I have to move the cursor to the right in order to get on the new monitor. How can I change so I can just move my cursor to the left and get it on my new 2nd monitor?

  Right-click on the desktop and then clicking display settings by clicking Customize to open the display settings. In the display settings box, click and drag the image to the monitor 2 to the left of the screen 1. Click on the button apply, then check. Click Ok to exit.

• How to install and run a 2nd monitor

  How to fix, install, or run a 2nd monitor of my laptop? Windows Vista

  Hello

  Do not forget to check with your system manufacturer, the documentation online and the drivers and their
  Forums (if any).

  Your laptop should have a video which will allow to another monitor be hung and more
  the built in LCD. You then decide if you want that the monitors to display different
  programs or be used as a large screen where you can move programs from one screen
  to the other.

  Of course your system, a video camera and its drivers have to support with a 2nd monitor.

  Two screens are better than one
  http://www.Microsoft.com/athome/organization/twomonitors.aspx

  Work and play better with multiple monitors
  http://Windows.Microsoft.com/en-us/Windows7/work-and-play-better-with-multiple-monitors

  Move windows between multiple monitors
  http://Windows.Microsoft.com/en-us/Windows7/move-Windows-between-multiple-monitors

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• 2nd monitor

  Can I attach a 2nd monitor the Omni of all in one?

  Hello

  See page 16 in the manual of the AOC for the solution of the AOC.