I deleted by mistake com6 usb modem com port, now when I troubleshoot it shows no modem usb driver not found.

Similar Questions

• USB drive not recognized on the A30-151 in XP

  After a clean install of Windows XP Pro on a Satellite A30 151, a USB device remains in the category 'Other' (after installation of the graphics and audio drivers, modem) for which no driver seems to be available on the drivers CD. At this point, the category "USB" contains four entries, two standard "Universal Host Controllers" and two "OpenHost' controllers, with the default drivers.
  I suspect that the missing device can be a USB 2.0 "PCI controller host improved USB" from another manufacturer, but Toshiba does not offer a driver for XP for it then it should be supported by the OS (?).
  Any suggestions as to what can be and what drivers need?

  It turns out that XP does support USB 2.0 according to the SP1, it seems a pre - SP1 version of XP Pro leads the native Windows drivers is not available. For anyone in a similar situation, it seems as if a) upgrade to SP1 or b) install the hotfix Q312370)

  http://www.google.com/search?hl=en&q=Q312370_WXP_SP1_x86_ENU.exe

  for the English version should throw a lot of download sites) followed by the autodetection of the native Windows drivers should do the trick. However, the following SP1 problem may come into play

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?service=EU&FID=TRO0000001c0d

  in this case, the "NEC PCI to USB Enhanced Host Controller B1" driver required original can be found by searching for "USB driver" for "Windows 2000" for the Satellite A30 Toshiba driver download page.

• HP 15-ac025TX (M9V00PA): network controller & USB controller driver not found and wifi not working not

  Hello I bought HP 15-ac025TX (M9V00PA) computer laptop computer laptop.  I installed all the drivers from the HP site, here is the link

  http://support.HP.com/in-en/drivers/selfservice/HP-15-notebook-PC-series/7771404/model/8326084#Z7_30...

  but still driver network controller not found also wifi works do not I installed blutooth drivers too. I use Windows 7 sp1 (32-bit)

  For network controller device ID is PCI\VEN_14E4 & DEV_4365 & SUBSYS_804A103C & REV_01

  Secondly, univeral serial bus controller driver (usb) not found

  I installed all the drivers on link also updated windows, but still no solution

  the usb controller hardware ID is

  PCI\ VEN_8086&DEV_9CB1@SUBSYS_80C2103C&REV_03

  and finally, I am unable to download the graphics driver AMD/Intel switchable high definition (HD). the download link works not

  KINDLY SOLVE THE PROBLEM

  Thank you

  Update:

  While the pilot I know work is not made yet, I did some detective work and explored some other links from HP broadcom WiFi card driver files, and I found one that should work for you.

  He says that it is for HP desktop PC, they put the exact same form factor of the card wireless to a desktop PC in a laptop.

  I see not why this driver would not work, because the configuration file contains the same hardware ID you have posted.  Here's a partial copy and paste of the setup information file driver, and you can see the hardware ID you have posted is supported by this driver.

  x 86-Win7
  ;
  [BROADCOM. NTx86.6.1]
  % BCM430N_DeviceDesc % = BCM43XNG_NT61, PCI\VEN_14E4 & DEV_4365 & SUBSYS_2230103C
  % BCM430N_DeviceDesc % = BCM43XNG_NT61, PCI\VEN_14E4 & DEV_4365 & SUBSYS_22D3103C
  % BCM430N_DeviceDesc_HPY % = BCM43XNG_NT61, PCI\VEN_14E4 & DEV_4365 & SUBSYS_2232103C
  % BCM430N_DeviceDesc_HPY % = BCM43XNG_NT61, PCI\VEN_14E4 & DEV_4365 & SUBSYS_22D4103C
  % BCM430N_DeviceDesc_HPY % = BCM43XNG_NT61, PCI\VEN_14E4 & DEV_4365 & SUBSYS_804A103C

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=cp_149257_1

• external USB drives not recognized under xp pro 64

  I bought a genuine version of XP Pro 64 to load on my computer and because Win 7 froze with drivers nVidia graphics.

  When I plug a recently bought Seagate Goflex or one of the new Western Digital external hard drives, they are not recognized.

  They do not show on my computer or disk management at all.

  They appear in Device Manager with a yellow question mark big under 'other devices '.

  I right click on the hard drive in the Device Manager to update the driver, and it always fails.

  Before ask you, these USB drives work perfectly on my other XP Home 32 System. The cables are good.

  I tried different ports, front and rear... no good.

  My system XP 64 Prp is updated w/Windows update and software chip to the motherboard.

  Strangely, I have a hard drive WD Passport USB 500 Gb one-year-old that works fine on XP 64 system.

  WD technicians say that I am the only one with this problem. PlugNPlay needs no driver, what do say.

  I also have IDE/SATA USB cable w / the power cable, I use to connect my old internal drives.

  Works fine on the XP Home 32, but I get the error "USB to ATA/ATAPI Bridge" in the device with the 64-bit System Manager.

  Yes these devices are all "turned on."

  Something is missing on the XP 64 system.

  Help is very appreciated.

  Been looking for a solution for a week now.

  Thank you.

  Hello

  See the following articles that may help you resolve this problem.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive
  http://support.Microsoft.com/kb/925196
  Why my computer does not detect my new USB device when I run Windows XP or Windows Server 2003?
  http://support.Microsoft.com/kb/314634

• Finger by scanning and mouse ports usb is not found - now! In addition, password does not work!

  My finger swipe and the USB mouse positions is not found - now! In addition, I forgot my password for the unit - VGN-AW120J! I think I have at the office this unit under the username above with a different through Sony password when I buy the unit - some time ago!

  Hi Robert,.

  It seems that the Windows login password has been forgotten and the prints Print sensor in does not.

  In this case, I suggest you to perform a complete system restore to solve the problem. Follow the steps here to perform the system recovery: http://www.kb.sony.com/selfservice/documentLink.do?externalId=C459775

  It is necessary to take backup of all data before performing the system recovery, it clears everything from the computer and restore the computer to factory settings.

  If the problem persists, contact Sony Service support here: http://esupport.sony.com/US/p/service.pl

  Note: If my post answered your question, please mark it as an "accepted Solution".

• El Capitan - Ext. USB Drive not mounting

  Since the upgrade to El Capitan, I have not been able to access my external USB drive. I read the other posts about this problem and none of their solutions worked for me. Through repeated trial and error, I came across a solution that allowed me to access my USB drive in El Capitan. By attaching a USB hub to USB port and your device your drive should become accessible. Depending on what type of car you join you may need a powered hub. I enclose a mSATA drive to a hub powered and well.

  Hi Bob, there.

  Looks like you're having connect your USB drive to a hub so that it works with your computer. I would reset your PRAM then your SMC in this order:

  How to reset the NVRAM on your Mac.

  Then:

  Reset the management system (SCM) controller on your Mac.

  If the problem persists after that I have would then start in safe mode to clear some system-level caches and perform a disk check and repair if necessary:

  Follow these steps to start in safe mode.

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  From: try safe mode if your Mac does not start-up

  Once you log in safe mode, reboot normally and try again the reader. Thank you for using communities of Apple Support, let us know how it goes.

• USB drive not readable on the Satellite A665-13W

  Hello

  I have the following problem. I have Kingston DataTraveler HyperX 64 GB (USB 3.0) by car and it is perfectly readable on other PCs without worrying if I connect it to the USB 3.0 or USB 2.0 ports.

  The device is detected in Windows 7 64-bit on Toshiba Satellite A665-13W and I see it in Device Manager. He invites me to open the disk E: (NTFS volume), but it looks empty when I open it in Explorer Windows with a certain delay when Explorer seems to scan drive.

  I see some errors in the event viewer such as:
  Event ID 11: driver has detected an error in the controller on \Device\Harddisk1\DR2

  But when I connect for example Patriot 8 GB USB drive it works without problem. When I boot Windows 7 in safe mode, the Kingston DataTraveler HyperX 64 GB drive is connected, and I can read it.

  What should I do to make it readable without going into safe mode?

  I have the latest BIOS 2.30, I tried to enable/disable USB legacy support, I tried the fast/normal startup, I tried to install the latest Intel Chipset drivers, I tried all USB ports, including one that can be used as eSATA port, but without success. I also uninstalled the recognized device driver and let Windows detect the device again and reinstall the driver, but also without success. I also disabled power management option to disable device, without success.

  When I start in normal mode, I can't read NTFS volume. When I boot in safe mode I can read. The USB works on other PC in normal mode. Old USB 2.0 USB key works in normal mode. Strange. It must be a firmware problem or driver in my opinion. If it is a hardware problem or device the device would not work in safe mode!

  Are USB 3.0 64 GB of storage devices that are compatible with Toshiba laptops with USB 2.0 ports?

  There could be a problem of compatibility between the USB controller and the USB key.
  This compatibility questions aren't unusual.

  But I m wondering if you could try to fix this in the other direction:
  First check to see if the USB flash memory stick would appear in disk management

  Panel-> management-> disk management computer

  Here you will see all the partitions on the HARD disk and the USB connected.
  Check if you can format the USB key once more.

  If the USB does not appear here, try this method:
  Start the console by typing CMD
  Then type the command: diskpart and press enter
  Now, type command: automount enable and press enter

  Now, close all windows and restart the laptop.

• USB drive not appearing is not in the T610

  I got a USB standard with some of the files it contains.

  The image that I use on the T610 is the last image (6.1.7601.279)

  In administrator mode, I am able to save and display the files on the USB key. In user mode, the driver installs successfully but I can't display the USB when I click on computers. I don't see the Z disk.

  I searched and found that I can turn on USB storage media or off in the registry. The value of the key is set correctly (3).

  Now I don't have what I can do to get this working.

  Any advice?

  Thanks in advance

  The user account has political explore to lock the profile - including what readers are visible.  In this case, the NoDrives policy is configured to allow only Z:.  Load the user registry hive, NoDrives to include the drive letter of your USB drive and unload the hive for the user.

• external USB drive not seen

  Hello

  I just bought a Readynas RN212 as a replacement for my Duo (v1). But the external USB drive (Toshiba 2.5 inch, ext3), that I used as backup for my Duo and always worked perfectly, is not recognized in the RN212.

  I have ssh - ed at the RN212 and did a manual mount: mount-t ext3/dev/sdb1/mnt which worked. The player ends up in/run/udev/data.

  Any idea what's going on?

  Kind regards

  Eric

  Hello espakman,

  This USB has data on the volume of your old Duo? If it is possible to format, use the NTFS system.

  If it contains all the data, it's that it may be preferable that you contact support for the RN212 so it can be verified from the backend.

  Kind regards

• USB camera not found EXE, IMAQ void VI error running program

  Hi, dear guys and managers on board

  I'm a new engineer in Germany. Recently, I've converted a program of USB camera that is used to read image of LabVIEW 7.1 version to version of LabVIEW 2010 barcode matrix, with LabVIEW 2010, module Vision Development, software vision purchase August 2010 is installed.

  The program works well, and I have generated an EXE file to run the tool on computers without LabVIEW 2010 is installed.

  I installed the runtime LabVIEW 2010, Vision Runtime Engine(evaluation version) and going TO (evaluation version).

  However, when I run this program, I still have this error, saying that "IMAQ Read Data Matrix code bar 2" not found.

  Would someone please so kind to give me any suggestions? Thank you very much!

  
  

• for hp laptop d008se, boot usb drive not in the sequence of boot in the bios!

  I have purched a HP Notebook Laptop (HP D008se) model with Win 8.1 only language X.64 bits.

  I want to boot from a USB key, I went to the bios by(ESC+F10) and went to the boot order, but there is no USB drive

  only (hard USB, CD/DVD, network, the OS Boot Manager), ok. I did the last Boot order

  I put my USB Bootable and press ESC, but my Flah is not in the list.

  Please, could say one met my, what I can do to boot from My USB, and is this model not supported USB bootable... it will be a problem for me!

  Spoiler (Highlight to read)

  

  

  Press the power button then immediately press the ESC key to access the boot menu choose the F10 key to enter the BIOS. Click the System tab and then click start options.

  In the start options, enable legacy support option.

  

  

  Press F10 to save changes and your computer will restart.  Make sure that the USB is connected to a usb port. Now you should see the USB in the selectable start options if it is indeed a boot device.  If the USB was not bootable you still not see in the list.

• HP ProtectTools encryption recovery disk: USB drive not recognized

  I encrypted hard drives of a couple of notebooks HP Elitebook 8560p using HP ProtectTools drive encryption. Saved 4GB USB DRIVE formatted FAT32 discs recovery keys. BIOS and latest available drive encryption versions today.

  Today I decided to test the functionality of recovery. So, when the BitLocker Drive login screen appears at the start, I select Recovery. Then I click on browse to find the recovery on the USB drive key. However, the USB is not visible doesn't help not hit 'refresh readers '. I tested it on two laptops. The system simply does not see the USB drive at this stage (works very well under Windows). Any ideas? I lived the most obvious BIOS settings.

  An update on a case where someone has the same problem:

  The USB key is recognized and everything works fine if the laptop is in its docking station, and the USB is connected to the USB port of the docking station.

• USB drive not detected on Windows 7, 4 GB RAM.

  I tried to apply the KB976972 fix suggested by microsoft, but the update he says not this OS.

  I tried all supported x 64 versions of Windows 7 and Windows Server 2008 R2: Windows6. 1-KB976972-x 64.msu, but the update said it is not for this OS. My system says that my OS is 64-bit.

  It might be useful to take your USB drive to a friends or family member and just checked on another computer to see if works on their computer. If this does not work on other machines, it could be the casing of the drive or the disk itself that has become defective. MyPcHealth - free tools

• USB drives not appearing is not in my computer, even if they can access

  This problem happened for years and there were so far no possible way to fix it.

  When I have a USB device is plugged, the folder on the drive does not appear in the post. Yet it appears in the Device Manager or in devices and printers. If I type in the drive letter (H: /) in Windows Explorer, it works.

  Also, in devices and printers, the "Browse files" option is grayed out and I can not access network drives - I can't get C to G (E being my DVD player and G being my external hard drive). It only works if I type in the drive letter.

  Is it possible I have USB drives appear in my work so that I don't have to type the letter to? I tried USBs on my other computer and it works fine.

  Hello Tsukasa,

  Please keep us updated on the status of the issue.

  I'm glad that you managed to solve the problem.

  I appreciate your effort, time and patience.

  You can mark your answer as a response.

  Please do not hesitate to answer, if you have other problems with Windows.

  Thank you

• USB drive not recognized in windows 7 but is recognized in windows xp

  I downloaded music files from my computer windows xp on a sandisk cruzer usb flash drive. I tried to download these files to my new laptop with windows 7, but the laptop has stated that it does not recognize the device. What I d0 now?

  I have a 2 GB SanDisk Cruzer so I'm sure it 'll work with Windows 7. It is possible that the Sandisk has installed a software owner and Windows don't is not running. There is an updated version of the US software on SanDisk site which may help.
  http://KB.SanDisk.com/app/answers/detail/A_ID/3682/SNO/0

  Personally, I would remove the U3 of the reader software because it is NOT necessary for training at work. I had to search the disk and launch a program to "delete" in the Launchpad folder on the drive. Once removed, it should work without interference from this program.

  Here is a link to the SanDisk site as well. You should be able to easily do the XP.
  http://KB.SanDisk.com/app/answers/detail/A_ID/2550/SNO/0

  I hope this helps Mark <> Microsoft Partner