I get a hard drive error at each start of my G4-1001TX laptop.

Similar Questions

• Hard drive error, does not start.

  Computer does not start. I get this failure code:
  Rw1xtw-7ax87b-mfpv6k-619403
  
  Can't find any information on this subject, can someone shed some light on this subject for me?

  Hello

  It decodes for hard drive error 305 or the hard drive has failed, you will need to get the replaced hard drive and reinstall the OS and have a Fresh start, note that all your data is saved on the hard drive will be lost.

• Re: Satellite A40 - hard drive error - will not start

  My friend bought this laptop in April 2007 and has been very happy with it until about a month when he stopped startup in windows xp.

  At the start, she now gets the message

  "PXE - E61 media test failure - check the cable for.
  "PXE - M0F outgoing intel boot agent"
  "Insert system disk in drive."
  "Press a key when you are ready.

  and then the laptop does not start in windows.

  I thought that the hard drive can have detached, so I took it out and he handed in a State, but in vain.

  I also tried to reinstall with the recovery CD but get the following error message
  status «»
  GDISK (E) no such fixed disk 1 "

  It is followed by * ERROR *.
  Error number 11030
  invalid message destination drive
  X;

  I ran a Toshiba (or he could have Hitachi) utility disk that I burned on a cd and went up on the audit boot.

  It said there are problems on Toshiba MK4025GAS, which is the hard drive. details coincide with what it actually says on the disc.

  The BIOS sees the drive start on as he is listed as the master, with the cd as the secondary drive.
  Therefore, is it true that the drive is broken. If so - can it be repaired or is there another solution.

  I tried Googling the error message and there are conflicting messages on this issue, so your help would be very appreciated.
  It seems crazy that the reader can break after only 18 months - was there a defective batch?

  If that's the case Toshiba offers a replacement or it will cost a lot?

  Thank you

  Nashy

  Post edited by: Nashy - sorry - it was bought in 2007 is NOT 2006

  In your case, the HARD drive is certainly defective and you need to replace. Satellite A40 is pretty old laptop without guarantee valid and there is no replacement from Toshiba.

  Just buy a new HARD drive. Hard drives for this good old classic are not more expensive.

• Hard drive error (HP ENVY 17 Notebook PC, PN: A9P79UA #ABA)

  at startup, I get the Message disk error hard and please run the hard drive test in the System Diagnostics

  Hard drive 1 (3F1)

  F2 System Diagnostics

  For more information, please visit: www.hp.com \go\techcenter\startup

  I ran boot test, 100% of the system memory is ok, but it took a lot of time

  I ran disk hard test then I get this message

  "Main hard drive Self Test

  Quick test

  Red, I get (HDD 1 fault)

  Hard drive Self Test

  Full test

  Red, I get (HDD 1 fault)

  INTELLIGENT testing of output control

  "color yellow, I get (SMART hard drive SPENT).

  Please how can I solve this urgent problem. Moreover, how much disk hard comes with the hp envy 17 notebook pc?

  HP ENVY 17 Notebook PC, PN: A9P79UA #ABA {deleted private information}

  Here are the specifications of your laptop of HP ENVY 17-3077NR. You receive the error code indicates that your computer's hard drive has failed or is about to fail. To resolve this issue, you must replace the hard drive with a new one that is similar to the original hard drive. It is clear this form, this model uses a single 750GB 2.5 "SATA hard drive.

  Once you replace the hard drive, you will need to use your HP recovery disc set staff to return the computer to a factory State. If you don't create these disks, you may order from HP or third-party provider ComputerSurgeons.com. If the figure 25 Windows product key on your computer is still readable, you can download Windows and install it using the product key on your computer.

  Please click the White Star of KUDOS to show your appreciation

• Start up and boot problem. Hard drive error. HP pavilion laptop Home Premium. Windows Vista preinstalled. No cd came with it.

  Nothing new added to comp. Got the hard drive error message and followed the instructions to fix/repair. All translations tried (almost every test suggested/memory/hard drive, etc.) could find NO problem with the memory or hard drive.  Once I have pass the problem to boot/start the computer works fine!   Crazy!  Any sugg. would be appreciated.

  Hello

  ·        Since when are you facing this problem?

  ·        What are the fix and repair that you tried to solve this problem?

  ·        Outside this disk verification error, do you get any other error message?

  Method 1:

  I suggest you to do a scan of the SFC. File system (CFS) Auditor verifies that all Windows 7 system files are where they should be as they are by default and not corrupted, changed or damaged.

  ·        Click Start, click principally made programs, accessories, right-click on command prompt and select run as administrator.

  ·        Click on continue or provide administrator credentials if prompted.

  ·        In the command prompt window, type the following text, and then press ENTER:

  ·        sfc/scannow

  ·        You should see the following message on the screen:

  § Begin the analysis of the system. This process will take time.

  § Beginning verification phase of system scan.

  ·        % Of verification complete.

  ·        Once the scan is complete, a test to see if the problem you are experiencing is resolved or not.

  For more information, see the article mentioned below.

  http://support.Microsoft.com/kb/929833

   

  Method 2:

  I suggest you to set Chkdsk to run when the system restarts the next time. Follow the steps mentioned below to set Chkdsk to run when Windows Vista reboots the next time.

  a. click on start, then run.

  b. in open, type cmd, and then press ENTER.

  c. use one of the following procedures:

  Procedure 1: To run Chkdsk in read-only, at the command prompt, type chkdsk, and then press ENTER.

  Procedure 2: To repair errors without scanning the volume for bad sectors, at the command prompt, type chkdsk volume: / f, and then press ENTER.

  Procedure 1: To run Chkdsk in read-only, at the command prompt, type chkdsk, and then press ENTER.

  Note: If one or more files on the hard disk are open, you will receive the following message is displayed:

  a. Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

  b. Type O, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.

  Procedure 2: To repair errors, locate bad sectors and recover readable information, at the command prompt, type chkdsk volume: / r, and then press ENTER.

  Note: If one or more files on the hard disk are open, you will receive the following message is displayed:

  a. Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

  b. Type O, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.

  You can see the article mentioned below for assistance.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Method 3:

  I suggest you to do a system restore. Follow the steps mentioned in the article below.

  What is system restore?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• hard drive error message 1

  Whenever I turn on my laptop, a message appears that there is a problem with my hard drive.  I have prees F2 to get the Diagnostics utility and run the hard drive test. When I do I get this message

  hard drive error

  Failure ID: 90 c 633-6am70r-mfgk0k - 60 c 203

  Product ID: c2n26ua #aba

  Hello

  Error code 24 characters will be a Smart failure or disk Self Test - in both cases, this would indicate that hard is defective and must be replaced.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• Game-hard drive error

  Hi all

  I had to increase the size of some VMDK today and didn't want to do it manually. So I thought, I'd give PowerCLI a shot.

  My script is supposed to set the size of all the VMDK with a given name in a certain store of data to approximately 50GB. All hard drives that are chosen are 10 GB in size but Set-hard drive gives me an error saying that it can only expand/extend (forgot the exact wording) hard drives. Apparently, he thinks that my disks are larger than the size of the target? This is not the case, and if I run the command manually for a virtual machine the command does what it is supposed to do. I don't know what could cause this behavior.

  Maybe someone can take a look at my script and see if there is something wrong with it?

  At one point in the command gave me an error saying something like that I had to connect to a host directly it is why my script may seem a little weird.

  I should mention that this is my first PowerShell script ever and I have

  have no experience in programming, so please don't laugh too hard

  Thank you in advance!

  Script: http://pastebay.com/99124

  Hello

  As you noticed correctly Get-hard drive - data store needs direct connection of ESX. In this case, the cmdlet uses the VirtualDiskManager to directly query the vmdk file information. This is also the reason why property persistence is unknown - this information is available through the virtual machine (Get-disk hard - VM myVM).

  However, even if you get the hard disk, the navigation data store, expand operation should be fine.

  The error you are getting is because HostUser, HostPassword, GuestUser and GuestPassword tells the cmdlet to extend the drive hard and resize the hard disk in the guest virtual computer OS. If you want to do you need to get the hard drive using the virtual machine, it is attached to.

  So to remove this parameters should extend the vmdk file as you want:

  
  connect-viserver -server $vmhosts[0] -user $huname -password $hpword
  $vmharddisks = Get-HardDisk -DataStore VMFS-OS-LUN100 | where { $_.filename -like "*HD*"}
  foreach ($vmharddisk in $vmharddisks) {
          Set-HardDisk -HardDisk $vmharddisk -CapacityKB $cap
  }
  

  Kind regards

  Yasen

• Satellite L350 - persistent master hard drive errors

  I've known persistent main hard disk errors. Errors, in their first incarnation, were windows freeze at loading screens and screensavers, and then developed by stopping Windows to boot at all. It certainly would not start normally and sometimes would not start in safe mode. I used the recovery partition to restore the computer to its factory settings. A day or two later, the same symptoms began to manifest again, although not as severely. The hard drive errors, freeze on screens and loading screen savers.

  My question is: if I re - format the hard drive master, thus destroying the recovery partition, I could then just restore windows from a newly formed recovery CD? And, in addition, what is the probability that reformatting the drive hard completely would have an effect on the frequency of errors?
  If the hard drive is simply borked, format or not? And if yes, what is the next step?
  Could I restore windows on my drive hard slave and give up on the master?

  Thanks in advance.
  Mike

  Hey Buddy,

  Are you sure that all these problems related to the HARD drive at 100%? How did you check that?

  I don t mean it s not the HARD drive, theoretically, you could be right but before you think to change the HARD drive please use a diagnostic tool special for HDD as Drive Fitness Test:
  http://www.HitachiGST.com/support/downloads/#DFT

  This tool can check your HARD drive for bad sectors.

  If the HARD features of bad sectors disk, formatting will not help you because the sectors are physically damaged. With other words, the only chance is to exchange it.

  But if you have already used the recovery feature of HARD Toshiba drive to reinstall Windows you can say s that no problem of software and it must be hardware related. ;)

• I can't get my hard drive to recognize that I have a CD in the tray

  I can't get my hard drive to recognize that I have a CD in the tray.  I can only open and view those that I already copied. Why?

  There are a number of possibilities here.

  1. assuming you have tried several different blank CD (if you are fairly confident that the problem is not the media), it is possible that the laser "burning" the recordable CD is dead. Because this isn't the same laser that reads the CD, you can always read but not write.  If this is the case, the only solution is to buy a new CD player (not expensive).

  2. your CD drive (E :) shows when you click on my computer?  I think it does, or you did that you can open and view copies of files, you have already copied to other CD.

  3. open Device Manager (start > run > devmgmt.msc > OK)

  • Expand the category of CD-ROM/DVD-ROM readers by clicking on the + sign to the left
  • Y at - it a warning next to the entrance icon?
  • Double-click the entry for your CD player
  1. That said under the "device status".
  2. What would you say (at the bottom) under "use of the device.
  • Close the Properties window and Device Manager

  4. open my computer, right-click on the icon for your CD drive and select Properties

  • Is there a tab "recording"?
  • If there is a 'Recording' tab, click on it.  Is the box to "Enable the writing of CD on this drive" checked or unchecked?  (Do not change at this stage)

  I'm not very familiar with Media Center Edition.  In the past, when you copy files to a CD, how did you do?  You just drag files to the letter of the CD-ROM drive in Windows Explorer, or did you have to open an app?  If the latter, what application you use to copy files to a CD.

• Laptop HP 2000: hard drive error

  Hello
  I have upgraded to Windows 10 one a few days ago and then yesterday when I went to turn on my computer it says this.

  Hard drive error
  Please run the hard drive Test in the diagnostic system
  Hard disk 3 (3F1)

  I ran the test drive and that's what he said

  Smart check: PAST
  DST short: FAILURE

  Help, please!

  You will need to replace the hard drive. Update to Windows 10 had nothing to do with it. After the back if you want to help find a car and its installation and reinstallation of Windows. If your Windows 10 appeared as it is activated, you can do a clean reinstall of Windows 10.

• to get a hard drive

  Hi I have a laptop compaq presario CQ50 - 228-CA. Told me to HB to get this hard drive: Hewlett - Packard (HP) 613070-001-250 GB 7.2 K RPM SATA Hard Disk Drive (HDD). This hard drive is expensive at a certain site online. I want to get a hard drive cheaper on another site with this info: 250 GB SATA 5400 RPM hard drive for Compaq Presario CQ50 - 228 CA CQ56-219WM CQ60-420US and I want to know if that hard drive work on my laptop? He mentions my model but HB make me feel that I have to enter the first hard disk that I have just mentioned. I never bought a hard drive before. I want to trasfer all data, including windows vista of the old hard drive hard drive with a USB adapter, again but I do not know what USB adapter, I'm supposed to buy? Thank you

  You can buy any 2.5 inch width 9.5 mm SATA HDD thickness of and there are now some very good deals out there. I suggest that go you to newegg.com and order one (you'll like 3 days). and get also a "drive upgrade kit" which will be cloning software and the cables you need.

  My humble recommendation:

  320 GB 7200 RPM drive to 65 dollars shipped:

  http://www.Newegg.com/product/product.aspx?item=9SIA2W014P4564

  Kit upgrade with external caddy and also cloning software:

  http://www.Newegg.com/product/product.aspx?item=N82E16817155602

  With refunds, it comes to a total of $100 and your laptop will go faster, to start.

  This manual (page 10) shows how to do the installation:

  Operating manual

  Repeat: You don't have to buy from HP or use a hard drive HP part number. They are generic standard of the industry.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP elitebook 2530p: hard drive error

  My elitebook 2530p says non system disk or disk error. I changed the hard drive of the diving with installed on Windows 7 starter. But the same problem of disc errror coninued. I run the hard drive, running-in and start test, but failed. When you press on the lower part of the bios it says bios corrupted or missing. What would be the best solution? need your help. Thank you

  hayford84 wrote:

  My elitebook 2530p says non system disk or disk error. I changed the hard drive of the diving with installed on Windows 7 starter. But the same problem of disc errror coninued. I run the hard drive, running-in and start test, but failed. When you press on the lower part of the bios it says bios corrupted or missing. What would be the best solution? need your help. Thank you

  So you took out the hard drive and put in a new hard drive?

• Hard drive error, but passes diagnostic

  I have a vostro 320 all in one computer. Yesterday he left initializing with a hard drive error, but when I run the hardware diagnostics all past. When I go into the installer the Bious does not see the hard drive. Current Bious is 1.2.0 and current is 1.4.0.

  If the BIOS does not see the hard drive, no - you will need to replace the disk.

  You can take a chance on the resettlement of the player (unplug the system and disconnect and reconnect the hard drive), but if so, it is not detected by the system, it is toast and needs to be replaced.

• I copy / paste a file from a hard drive to a usb port and now I lost the USB I get the hard drive?

  I move a file from a hard drive to a usb port and now I lost the USB I get the hard drive

  Tuesday, June 26, 2012 13:21:43 + 0000, MarvinBester wrote:

  I move a file from a hard drive to a usb port and now I lost the USB I get the hard drive

  "Deleting" a file does not actually delete it marks just the space
  also available to be used. There are third-party programs that can
  sometimes recover deleted files. The problem is that the space used by
  the file is likely to be replaced very quickly, and it makes
  the unrecoverable file.

  So your chances of successfully recover this file are decent if you
  Try it again immediately after the deletion of it and go quickly
  downhill from there. If you have used the computer since then (for
  example to write this question and read this answer), your chances may
  be very poor now.

  But if the file is large enough, it's still worth a try. Stop
  using the computer in question immediately, if you have not done
  already. Download an undelete program (and here's one:)
  http://www3.TELUS.NET/mikebike/restoration.html but there are several
  others to choose from; Do a search) on a friend's computer (do not
  it on yours because that would overwrite the files you want
  Undelete) and bring it to you on a CD or thumb drive to try.

  If that fails, your only recourse is to bring or send the disc
  a company of professional file recovery. This kind of service is very
  expensive and may or may not work in your case.

  Ken Blake, Microsoft MVP

• Dell Hard Drive Diagnostics fix hard drive errors

  My computer would stop working and say that I had a software problem.

  When restarting it would run for about 15 minutes and the cessation of work and

  show the same error.

  I have run the Dell diagnostic program and it showed that I have several

  Hard drive errors.

  After the diagnosis my computer now works fine.

  The diagnostic programs to correct the mistakes of hard dirve when he finds them.

  My computer is a Dimension 4700 running windows XP Professional

  Service Pack 3