I have a bodymedia device I plug into the computer and it will not read the program

Similar Questions

• I have a cd and dvd ROM on my computer but it will not read the discs and is not recognized on my computer

  Original title: no dvd

  I have a cd and dvd ROM on my computer but it will not read the discs and is not recognized on my computer

  Hi Lesliestones,

  ·         Did you do any change on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest refer you to the article in the Microsoft Knowledge Base and check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Method 2: You can run the fixit and check if it works.

  Your CD or DVD drive cannot read or write media

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  I hope this helps.

• How to get a popup when the device is plugged into the audio input jack?

  Original title - card Audio HELP

  I have a small problem that should be pretty easy to answer. A quick response would be nice. I'm new on Windows 8, and when you plug a device into the audio jack, a box used for poster asking which device is connected. Now that the box appears when I plug in a device. How do I get it to appear again? I have Windows 8, with player realtek HD audio. More info can be provided.

  Hello

  This problem can occur because of incorrect audio settings. Let's try a few steps to solve this problem.

  Method 1:
  As you use Realtek HD Audio, I would suggest trying the following steps and check if it helps.

  Enable auto-popup
  a. press the Windows key + X, choose Control Panel, select hardware and audio.
  b. scroll and select Realtek HD Audio Manager.
  c. click the icon for folder just above and to the right where it says analog panel back and just below the device's advanced settings.
  d. click Activate dialog popup automatically when the unit is plugged in.
  e. click OK twice.

  f. now, restart the computer and check the issue.

  Method 2:
  If the problem persists, I suggest you to set the headphone or speaker that you connect as a default value, and check if it helps.

  (a) right click on the volume icon in the system tray and then click on "recording devices".

  (b) right click on the space empty in the window pop up and then select "Show disabled devices" and "Show disconnected devices".

  (c) right click on the headset and then click on 'Activate'.

  (d) (d) mettre put out the microphone, then choose "set as default device".

  (e) click apply and Ok.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• How can I download pictures from my Sanyo 3810 phone on my computer? I have a USB cord to plug into the front of my computer?

  I have a Sanyo 3810 phone that I got from Sprint.  My contract expired and I went with cellular consumption.  I don't have a place for a SIM card in this phone Sanyo.  There are pictures on this phone I want to download on my computer.  Some of them cannot be replaced because they are my granddaughter who died this summer, at the age of 2 years.  I desperately need to find a way to get these photos developed.  Please, please help me with this dilemma.  I would be grateful what you can do.  I bought a USB cord to connect on the phone and my computer.  Thank you for your help.  Glenda Gamez

  Hi Glenda,

  Welcome to the Microsoft community!

  According to the description provided, looks like you want to know how to copy pictures from the sanyo phone into the computer.

  However, we need more information about the issue to help you better.

  Please help me answer this question.

  What version of Windows are you using?

  Visit this link for the operating system you are using.

  http://Windows.Microsoft.com/en-us/Windows/which-operating-system

  Here is a link that provides a soultion. Try the methods mentioned in this link and check.

  http://community.Sprint.com/Baw/thread/41336

  Note: Using third-party software or the link, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third party software or link can be resolved. Using third-party software, or the link is at your own risk.

  Keep us updated on the status of the issue. Using the windows-related issues feel free to post on Microsoft Community.

• AutoPlay option appears not when a device is plugged into the system

  * Original title: auto window will appear after connecting my phone to the computer using the usb cable

  Oh it's so it's the easiest thing, I would get the window that is fast when I plug in my phone to the computer with a usb cable. For some reason any it don't make anymore however usb is recognized because she sees very well. Thank you for your help.

  1. Open AutoPlay by clicking the Start button, then Control Panel. In the search box, type autoplay, and then click AutoPlay.

  2. In the list next to the device or media type, click the new action you want to use.

  If this has no effect when you plug in your device, make sure that you use a data/charging cable, not just a charging cable.  If it still does not work, try a different USB port.

• I have my Toshiba flash drive/Memorystick (same thing or not?) plugged into my computer and it cannot extract to Windows Media Player

  I am trying to get all my music in my WMP library, and there is no options to rip anything, but a CD; the previous answer is meaningless for me, because in MY WMP there is nothing that says 'Tools' that I can click on. What Miss me?

  Hello

  Step 1: You can follow the steps in the previous thread: http://answers.microsoft.com/en-us/windows/forum/windows_xp-sound/how-to-transfer-music-from-flash-drive-to-the/9043fd94-f90b-46b0-b3a0-b909639f6d41

  To access the toolbar, press Alt, or right click on the arrows at the top of the media player.

  Step 2: Alternatively, you can manually copy the files from the disc to the My Music folder and then drag and drop it in the folder my music in the Media Player library.

• My HP PSC 1200 is plugged into my computer and the computer says I need to turn it on, it has power to it, the power light is on. Can someone help me?

  I have a new HP computer.  It is around the age of 6 months.  My printer a HP PSC 1200 worked with her.  all of a sudden the printer does not work.  The USB cable is connected and so is power.  I have a green light on my printer, but it still doesn't work.  Can someone help me?

  If a connected USB device is not visible on the PC to which it is connected, there are three places to look for trouble: on the device, the connection between the camera and the PC and the PC.  First, try the device on another PC.  If you know that island same symptoms occur, is the printer or the cable.  Try a different cable.  If this does not work, you need a new printer or your printer needs maintenance.  If it works on the other PC, you know that the problem is your PC.  Try a different USB port.  If it still does not work, try another device on the USB port.  This should give you enough information to determine the likely source of the problem.

• My device hp officejet 5510 all-in-one printer always says me I have a paper jam. I do NOT have but I can't get rid of it and it will not print? Help!

  How can I get my printer (hp 5500 series) to print when he always tells me that I have a Paper Jam... that I do NOT!

  Help/support on the pages of HP support for your model, review its their printer

  http://h10025.www1.HP.com/ewfrf/wc/product?CC=UK&LC=en&DLC=en&product=311255

  Or the HP shortcut that was created on the desktop when you installed the full features software

• How can I make my default player for windows media player. I have upgraded to windows explorer 9, now quick time is the default and it will not read the attachments of wave?

  I downloaded explorer 9, now I can't read attachments in wave. a box opens and says open or save and I click Open and nothing happens. It seems that the system uses quicktime. I want Windows media player to be my default player. also, when I play a cd. He does not play in windows. Help, please.

  Hello, EdwardMLodzienski,

  Start > default of programs

  Click Set Program Access and Computer Defaults

  Click on the arrow in front of the custom (right) down

  Scroll down to choose a default media player

  Select Windows Media Player and click Ok

  Close the window

  You can also access two default programs in other ways.

  1. open Control Panel > default of programs

  2 tools > Internet Options > Programs tab

  Click on define programs and the same that you opened using the directions above will display

• Why many cinema screens have half-a-block of pine, to plug into the full-size DVI connector?

  Why have the many Cinema Display (especially the 2005-20-inch model) half-a-block of pine, to plug into the DVI-connector socket full large?

  The other half-a-block of pines just doesn't seem to be there?

  DVI can be single-link or dual-link.  Resolution higher than 1020 x 1200 need dual-link.

  http://www.showmecables.com/images/catalog/product/DVIQA.jpg

  Sometimes simple link devices and cables use dual-link connectors, but with no wires connected to the pins double link, if you can not tell if something is dual-link just by looking at the connector.

• "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

  "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

  1. my laptop - acer aspire 5030 - has been having this problem for the last five months.

  2. I tried everything including changing service pack, as we have xp professional, he has recently upgraded to vista business 32-bit with service pack 1.

  3 tried all the methods start the laptop after a few hours, remove the battery, press the power button for half a minute, and so on.

  4. I finally he formatted a couple of times, but the problem is not.

  5. later, I improved the professional system of vista and installed the latest security patches, but the problem remains

  6. now, I started to update its drivers, although the device is identified to be connected, but is not recognized. "the error message" not recognized usb device "appears. I try to reinstall the drivers or upgrade of drivers, it does not. It displays the message "the drivers for this device are to this day.

  7. initially, the connection of the device, the drivers are installed but still the device does not show in Explorer.

  8. I tried to change some registry values by merging a regedit file in the registry - for display devices that are not present; but still, it has failed.

  9. I then tried to delete the file infcache1.inf in c:\windows\system32\inf, but the problem persists.

  10. Subsequently, I tried to create another registry entry to "disable selective suspend" in HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB by adding DWORD and assigning a binary value of 1.

  11. I tried later also to uninstall all the system devices including USB controllers, drives and the storage controllers, who must still without success.

  12. I tried to see if the drivers in safe mode, which they did not.

  13. I tried to delete the following registry entries =

  HKEY_LOCAL_MACHINES\System\CurrentControlSet\Enum | USB PORT; HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10318 & HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10200.  The computer does not have alow it.

  14. the BIOS indicates device pnp "disabled", which I also look for the BIOS settings, which do not allow me to change to change existing ones.

  15. I have not found the WINDOWS\SYSTEM32\drivers\USBSTOR file. SYS in my driver store. This affects the system?

  16. I also contacted manufacturers pnp devices that provided me with most recent and versions compatible drivers for my devices - namely an apple ipod & Seagate external HARD drive - but even after that the drivers are installed properly and the system rebooted the problem remains. Is this something to do with the updated playing driver registry entries does not after the update? OR is what registry entries are configured to only read the entries at the time of the installation of the OS?

  17. I also contacted local sellers who have suggested to me to change the "motherboard". This will help as a last resort?

  18. in the meantime I had also installed other operating systems to Linux - Fedora and Ubuntu; Full Windows XP - Home & Professional and Vista Edition. All these have been installed successfully but do not solve the problem of usb.

  19. I have also raised the original HARD disk & replaced by another HARD disk. also checked the power of all ihee and ehee usb ports to be at least 5 V. I also disabled the automatic deactivation of devices usb by the system. physical contact, ports and connecting cable is fine. the distribution of power is set at 10% for the ihee ports and 20% for ports ehee, which is what is should be the physical output is also close to 5V for all ports connected.

  20. all professional (hardware or software) should any solution for the problem of the usb ports on my laptop?

  Something that you haven't tried:

  How to fix USB device not recognized in Windows

  http://www.online-tech-tips.com/computer-tips/USB-device-not-recognized/

  I hope I could help

• My iphone does not appear as a device in itunes when plugged into my computer, how can I solve this

  My iphone does not appear as a device in itunes when plugged into my computer, how can I solve this pls help

  https://support.Apple.com/en-us/HT204095

• Problem installing drive USB Flash to use as RAM in Windows Vista, the device is plugged into an unsupported interface"

  Im trying to use a new 4G Verbatim USB flash as RAM drive. The USB 2.0 flash drive, micro size so I can leave it plugged dedicated solely to that purpose.  When I go to 'Properties' and I open the reading push tab I get "the device is plugged into an unsupported interface ' it is plugged into the USB 2.0 port I used before.»   When I plug the USB in an another store bought (more long and 8 GB) I click on the Ready Boost tab and I get the options use as RAM. This one is too long to use.

  Hello

  You can view the information of the link.

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-memory-in-your-storage-device-to-speed-up-your-computer

  Note: a flash drive may seem meet these requirements, but Windows Vista can still detect it not as compatible ReadyBoost if its rated speed measures sequential and random performance and performance is not always quick on the set of the flash player.

  Hope the information is useful.

• Reference DELL E510 won't record sound from the microphone plugged into the rear microphone port

  What is the problem with this DELL E510?  I tried to record the sound of port rear mic on this machine with Windows XP and now Windows 7. (Previously, I had recorded my old Dimension 2400 without difficulty).

  The E510 (which was originally a Media Center Edition with Windows XP) but who now has Windows 7 Professional, Service Pack 1 shows the following messages after I launch audio troubleshooting:

  "Audio device is disabled." and also, another message saying, that at least one of the Windows Audio services and/or generating Windows Audio endpoint are not executed.

  I have all the correct settings of the sound and a microphone to work plugged into the microphone port back. Obviously, speakers are working correctly.

  Please notify. Thank you.

  Thanks for your reply.

  I have sound, only the inability to record sounds through the rear microphone port.

  Early yesterday morning, I dropped on a solution for the use of rear microphone.

  I plugged my microphone in the front Tower mic port.

  I downloaded the free version of "RecordPad Sound Recorder" AND can't seem to record my voice in the computer through the front mic port.

  No worries!

• Connector MagSafe 2 (the part that plugs into the computer) is getting very hot.

  Hello! I have a MacBook Air (Early 2015) and when I load it, the plug that plugs into the laptop is very hot (I can barely touch). This only happens when I use the computer while I am it loads. When MacBook is in mode 'sleep' the plug only heat. Is this normal or something in my MacBook is broken?

  Hello...

  Make sure it is well ventilated > use and maintenance your Apple MagSafe adapter - Apple Support