I have a Canon pixma mx922 and seems to only print photos... How do I print a document?

Similar Questions

• I have a canon pixma 210 and lost the installation disc an idears

  I can't find the disc of installation for my canon pixma 210 y at - there some way around this or any idears, please?

  Have you tried to visit Canon website to see if the drivers and software can be downloaded here or a re-ordered installation disc?

• Canon Pixma MX922 problems

  I have a Canon Pixma MX922, I liked when he was running wireless on Windows 7 on my old computer.  Since I replaced my computer with a Windows 8.1 running a new, it does not work, it crawls.  If it moves at all.  Sometimes it will print a full page, but there usually prints some lines and spits half done page.  He's literally printed a page on a single line at a time - at about half the speed of old matrix printers!  What gives?  I have not changed wireless service - only operating system.

  You have installed the latest driver

  http://www.USA.Canon.com/Cusa/support/consumer/printers_multifunction/pixma_mx_series/pixma_mx922#Dr...

• I have a Canon Pixma MX 880 and when I try to edit or delete photos on my SD card,

  I have a Canon Pixma MX 880 and when I try to edit or delete pictures on my SD card, I get the following error:

  "You must be authorized to perform this action" and below:

  'You need permission of the administrator of the computer to make changes to this file.

  Wireless printer is installed.

  I am registered as an administrator, do not have access to any user account.

  The old problem mounted HP Photosmart I replaced, I could change, remove, etc. without problems.

  Hi ehnco,

  It seems that the read/write on the printer attribute must be changed.  Use the following steps to change the read/write attribute:

  1. Make sure that the machine is turned on
  2. Press the Setup> button.
  3. Use of the the button to select [ device settings], then press the button.
     The device settings screen appears. 
  4. Use of the the button to select [device user settings], then press the button.

• Canon PIXMA MX922 printer will allow no 2-sided Word documents

  I just installed a new Canon PIXMA MX922 printer to replace an old MX882.  Everything works fine and I am able to print on both sides documents from web pages and e-mail by checking the 'duplex' box on the menu drop down print...  However, I am unable to both sides print all Word documents.  No check box 'two-sided' descend, and no "duplex" option is available, as it was with the MX882.  I never had this problem with the old MX882.  Can you help me?

  Thank you very much.

  Hi LonnieC,

  To set the option to print double-sided on a Mac, please open the printer driver:

  1. Select layout... in the file menu of the application.  The Layout dialog opens.

  2. Select print... in the file menu of the application.  The Print dialog box opens. In the print dialog box, you can set the paper type and print quality for printing.

• I have a canon 70 d and just bought 12 elements. It will not open a file raw for me. I've been advised to download the latest version of camera raw, I did, and he always says that my camera is not supported. I really need to open my raw files. Peut

  I have a canon 70 d and just bought 12 elements. It will not open a file raw for me. I've been advised to download the latest version of camera raw, I did, and he always says that my camera is not supported. I really need to open my raw files. Can someone help me.

  Which version of the Camera Raw plugin do you have now?  Use the help / about Plug-ins / Camera Raw in the PSE to see Editor.

  Also this operating system you have, XP, Vista, or something more recent?

• My profiles of camera under camera calibration (standard, landscape, etc.) are missing since I updated to 5.6. I have a canon 6 d and my computer is a mac. How can I get these back profile?

  My camera profiles (standard, landscape, etc.) are missing (under calibration of the camera) as I've updated to 5.6. I have a canon 6 d and my computer is a mac. How can I return this profile?

  If you actually see raw files and not JPEGs, then I suggest that you try to reinstall Lightroom 5.6. If you look at the JPEG images then all you will see is "incorporated". I apologize if you already know that.

• Brother MFC-7420. Usually, it works on Windows 7, it will not print and I have to unload the coil and switch off the printer before Relighting.

  I use a Brother MFC-7420. Usually, it works under Windows 7, but from time to time (maybe 1 in 20 times) he will not print and I have to unload the coil and switch off the printer before Relighting. It is not always the case, but it is enough times to be a nuisance.

  Ideas, people?

  Hello

  This problem occurs when you make changes to the computer?

  Method 1: Diagnose and automatically fix problems printing and printer

  http://support.Microsoft.com/mats/printing_problems/

  Method 2: Refer to this link: I can not print from my computer via the USB port.

   
  http://welcome.solutions.brother.com/BSC/public/us/us/en/FAQ/FAQ/000000/002700/000006/faq002706_000.html?reg=us&lang=en&c=us&prod=mfc7420_all&page=FaqEndPage
   

  If you have problems, I haveinstall updated printer drivers, see this link:
  http://www.brother-USA.com/downloads/default.aspx?PgId=5&R3ModelID=MFC7420

  Refer to this: update the drivers for hardware that does not work properly.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  See also: printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  I hope this helps!

• Got paper stuck in the printer and now will only print proofs. How to reset the printer

  Got paper stuck in the printer and now will only print proofs. How to reset the printer

  It looks like you may have some saved jobs in your queue that need to be removed.

  Here's how:

  To clear the print queue, stop the print spooler service and delete all the jobs/print pending.
     
  You cannot delete all print jobs in the queue so that the Print Spooler Service is running.
        
  To stop the Print Spooler Service, click Start, run and enter in the box:
         
  services.msc
         
  Click OK to open the Services Applet.
         
  Locate the Print Spooler Service, right click and choose 'Properties' and then click on the "Stop" button to stop the Print Spooler Service is running.
     
  The option "Startup Type" of Service properties print spooler is usually set to "Automatic" (which is now a good time to check it out).
     
  If the "Startup type" is not set to "Automatic", set the "Startup type" to "Automatic" If that is your desire (which now is the time to check it out).

  Do not try to start or restart the Print Spooler Service immediately.  You must remove all print jobs backed up first...
     
  Then, delete all updates pending upward and forward to printing from XP.  If they do not print before, you will need to send the to the printer again.
     
  Using Windows Explorer, navigate to the following folder (assuming that Windows is installed on your C drive):
     
  C:\WINDOWS\system32\spool\PRINTERS
         
  Delete all the print jobs in queue (select and delete all the files) in the folder if the folder is without waiting for print jobs.  The folder must be empty when you are finished.
         
  Reboot your system and check the Print Spooler Service again to make sure the Print Spooler Service restarts automatically restart (given that the startup type is set to automatic).
     
  After the reboot, check again the Spooler Service for printing and the 'Status' column for the print spooler must be read "started."

  Submit new failure of print jobs.

• I was promised 10 photos free to start stock and I get only 9. How can I get my 10th?

  I was promised 10 photos free to start stock and I get only 9. How can I get my 10th?

  Hi Julia

  Unfortunately, there isn't an option to "unlicense" a picture but I have added a picture of credit to your account, so you can choose another.

  Thank you

  Bev

• Problem with new pixma mx922 and Canon Menu fast

  Just buy a Pixma MX922. Analysis of and print well. If I use the Quick Menu of Canon, it shows the scanner but not the printer, so I can't use all the photo print settings. I'm on a MacBook Pro with OS - X El Capitan version 10.11.2. It's connected to an AirPort Extreme wireless. Can anyone help?

  If you go to System Preferences, and then select Printers & Scanners 922 MX is listed as a printer Hello?

  If Yes, click the '+' and wait a minute or two IJ version appears and install it.

• Problem Canon PIXMA MP760 and Windows 7

  Hello.

  I just installed Windows 7 and tried to connect my printer (Canon PIXMA MP760). He finds some drivers it cost but it showd a mistake and this seems to be the main engine.

  I have also tried to download driver from here https://www.microsoft.com/windows/compatibility/windows-7/en-us/Details.aspx?type=Hardware&p=Canon%20PIXMA%20MP760%20Photo%20All-In-One%20Printer&v=Canon&uid=9792A005&pf=0&pi=4&c=Printers%20%26%20Scanners&sc=Multifunction&os=32-bit

  But when he took out and so now he appears just "check the connection of the cable between the printer and the computer... blabla".

  I tried to reconnect the printer, enable/disable, restart the pc, checked the cable connection +++ but I can't make it work.

  When I go to devices and printers, I see that the scanner of the printer part appears as a device, but not the printer itself.

  Someone has any advice on what to do to get it working?

  EDIT: I also tried to install the printer on another computer with windows 7. Same problem there. :(

  Hi printerhelp,

  Please do not forget to go to the Canon website to download the software and drivers for Windows 7, as the two look update:

  http://www.USA.Canon.com/consumer/controller?Act=ModelInfoAct&tabact=DownloadDetailTabAct&fcategoryid=334&ModelId=11010

  If this isn't your correct printer, you should be able to look it up directly on the Canon site.

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Canon Pixma mx922 screen begins to turn

  Just bought my Pixma MX922.  Its been great so far, the only thing is the screen continually without reason.  Looks like it is awakened by something random.  I have disconnected the telephone line, disabled all services cloud, and even when all the computers are off the screen lights up as his is about to do something.

  Someone at - he seen elsewhere or have a fix?

  Hello.

  The LCD display will wake up if the printer receives the signals.  If the printer is used on a network, monitoring of utilities such as a firewall or even your router may be peripheral Ping on the network.  This signal to wake up the display.  The nature of proprietary routers and firewall programs, it can be difficult to identify what is broadcast signals through your network.  If the printer is rarely used, you should consider switching off the printer on when it is not in use.

  It has not responded to your question or problem? Find more help contact us.

• Canon PIXMA 620 and Win 7 64

  I have a Canon Pixma620 installed on Win 7 64.  I installed the 64 drivers and can print a doc in word and and worksheets all right.  My pictures won't print properly, they always print the wrong size and orientation! Two days to try to solve this problem is driving me crazy...

  Hello

  Thanks for posting your query in Microsoft Community.

  I understand that you can not print photos in Windows 7.

  I imagine the inconvenience that you are experiencing. I will certainly help you in this matter.

  Please follow the steps in the link.

  Change the orientation of the paper (Windows)

  http://kbsupport.Cusa.Canon.com/system/selfservice.controller?configuration=1011&PARTITION_ID=1&secureFlag=false&TIMEZONE_OFFSET=&cmd=VIEW_ARTICLE&article_id=17742

  I suggest also refer to the operating manual of the printer for the print settings.

  Reference link:

  Choose printing options

  http://Windows.Microsoft.com/en-us/Windows7/choosing-print-options

  Hope it will be useful. If you still have questions, please reply and we will be happy to help you.

• The printer could not be detected on the message of network during the installation of the Canon PIXMA MX922

  Unable to complete the driver installation the new installation because of this message. Went through the establishment of the liaison WiFi several times and connectivity was still present. Connected to my D-Link router 626L and saw the connected printer but the referenced ip address is 0.0.0.0. Tried to assign a static ip address through the printer and also to use the Windows cmd prompt, all to nothing does not.

  Called Canon Support and these 2 changes in adjustment solved the problem:

  (1) turn off the Wireless LAN DRX setting

  (2) disable the IPv6 setting

  This article explains how to set the settings of the printer.

  Hi mimiaz58,

  Thanks for sharing!