I have a gateway desktoop which shows the bios setup utility. What am I suppose to do now?

Similar Questions

• Laptop turned on, password appears on black screen, windows loading bar appeared, then got two options in the BIOS Setup Utility and change Boot Device order, I don't know what is happening, help please!

  My sisters notebook froze and she turned off the power switch, when she turned on the screen was black and a password box appeared when I entered the password, the XP loading bar came as usual and then I had two options at the bottom of the screen. We want to press F9 for and the other was to press F10 for BIOS Setup utility, after seconds, the screen went black and then appeared again the password and the circle continues. The laptop is only 1 week and I don't know if it's something she did or if it's a technical foul, I would be grateful if someone could help me or if I should take it to a technician. The laptop is a Compaq Mini 110 and it works on Windows XP Home Edition.

  Hi, your sisters Notebook is under warranty and it could be a hardware problem.

  As the laptop is only one week.

  I suggest that advise you your sister back to the place where it has been sold since.

  Slan go foill, Paul

• The BIOS Setup utility

  When I boot computer, go into the BIOS screen & asks for my password.  I enter and starts normally.  I have removed the password for user accounts, but always ask for password turned upward.  What could I do?

  Is your time ok?

  I downloaded your manual but nothing in there.

  http://forums.Toshiba.com/tshb/attachments/tshb/brd_recovery/7820/1/Satellite20A210-A21520Series20User ' s20Guide.pdf

  Try http://forums.toshiba.com

  This could be a solution, but ask first of all in the forums of Toshiba.

  http://support.Toshiba.com/support/viewContentDetail?ContentId=2597187

• ProDesk 600 G1 BIOS configuration of the TPM secure through the BIOS Configuration utility

  We have a range of devices, computers HP desktop and laptops in our environment.  Devices are all running Windows 7 64 bit and should have Bitlocker enabled, but we found that some were not encrypted.  So I am trying to set up a remote BIOS and Bitlocker config activate software that we can get out via SCCM and then embed in a task sequence image for new machines.

  I use the Bios HP Configuration utility to check a BIOS password is set and then activate the TPM chip.  I took a BIOS config output of each of our models and created a settings file that has all of the TPM associated parameters of all models.

  At the moment I run Setup BIOS utility manually for testing.  On all models I tried that works very well, except for the 600 ProDesk G1 SFF.

  When I run the utility on the ProDesk 600 G1 MFS, it says that I have managed to update the settings, and when I check the BIOS, the TPM secure has been unhidden and the TPM Management was given to the operating system (two settings I change), but the TPM itself remains hidden.

  It's the release of the BIOS configuration utility (it uses the 2.60.13.1 version, which uses plaintext passwords.  I also tried with the 3.0.13.1 later version that uses password files - same result)

  C:\ > BiosConfigUtility64.exe /cspwd: "password" set: "TPM_Config.REPSET"
  
  < BIOSCONFIG Version = "2.60.13.1" Computername = 'HP600G1' Date = "24/07/2014" Time = "13:01:37 ' UTC '1' = >"
  
  < SETTING changeStatus = "pass" name = "Embedded Security Device" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [hidden device]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [device]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "Enable security on the next boot" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "The BONES of on-board safety management" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SUCCESS msg = "Successfully set BIOS config." / >
  
  < information msg = 'BCU return the value' real '0' = translated = '0' / >
  
  < / BIOSCONFIG >
  
  C:\ >

  And after a reboot (where it should activate the TPM), BIOS shows as disabled built-in safety device (see attachment for the image).

  I have tried everything I can think of to get this to activate, including:

  • Different versions of the BIOS configuration utility
  
  
  • Remove the password from the BIOS and the application in the same order as the parameters
  
  
  • Different passwords
  
  
  • Reboot and allowing the machine to start completely to Windows before checking if the setting took effect

  I also tried to add the utility and the commands for an SCCM package and it works directly and as part of a sequence of tasks to see if that makes a difference, but nothing I've done has activated the TPM module.

  I know that the TPM module works, as you can turn it on manually and then Bitlocker can be applied to the machine, but with thousands of devices in our environment, I need to get this job without the need for manual intervention.

  Has anyone else had this problem and found a solution?  Or has someone at - he managed to activate the TPM on the SFF of 600 ProDesk G1 using the BIOS Setup utility?  Any ideas / suggestions would be very appreciated!

  P.S. This thread was moved from the company PC - Compaq, Elite, Pro for HP PC Client management. -Hp moderator of the Forum

  This problem has now been resolved by HP.
  
  They provided a replacement motherboard for the test machine I was using that solved this problem. I don't know what kind of motherboard failure could prevent the activation via the script TMP chip but not prevent activation through the BIOS menu, but as a replacement solved the problem, then it must be a hardware failure.

• I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

  I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

  Ihab El-Sayed

  published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...

• Hi, I have a subscription in photoshop and creative cloud which includes the luminous room. but he asks me a serial number now; can anyone help please?

  Hi, I have a subscription in photoshop and creative cloud which includes the luminous room. but he asks me a serial number now; can anyone help please?

  Help creating cloud / Cloud Creative applications request serial number

  https://helpx.Adobe.com/creative-cloud/KB/CCM-prompt-serial-number.html

• I have several different cards to show the same article in a collection?

  I have several different cards to show the same article in a collection?

  Cause the client wants several different cards in the main browser page, but all of these cards must call or redirect to the cover or the main article intro!

  Thank you very much in advance guys!

  You may need to download the article several times.

• I paid for the pack of adobe PDF and I in some weird screen which shows the different products to buy. I just want to use the pdf pack to do what I need. any suggestions?

  I paid for the pack of adobe PDF and I in some weird screen which shows the different products to buy. I just want to use the pdf pack to do what I need. any suggestions?

  Hi jerrir58650452,

  You can access your service pack pdf by using the following link: https://cloud.acrobat.com

  Kind regards
  Rahul

• I hope someone can help me. I changed a few settings in the BIOS Setup, and now I have just a black screen. I changed the main boot to the DVD player device. is it possible to reset to original settings?

  I hope someone can help me. I changed a few settings in the BIOS Setup, and now I have just a black screen. I changed the main boot to the DVD player device.  is it possible to reset to original settings?
  I am running Windows XP

  clint341,
  Thanks for posting on the Microsoft Answers forum.  We cannot guide you more precisely by changing the BIOS settings that the BIOS settings are specific to your motherboard.  However, most (if not all) parameters of the BIOS have an option to restore the default BIOS (sometimes called "default opitimized").  It may be an option in the menu that you highlight, then press enter or it can be assigned to an F key and States at the bottom of the screen, press F? for the default settings.  I hope this helps.  If you are still not able to reset, check with the manufacturer of PC for more information about the BIOS. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• quedtion on EFI which replaced the bios

  Hello

  I read on EFI which replaces the bios and I see that it also has a shell environment.   I want to know in which situations you can use this shell command in EFI and what is the benefit of it.  because for the bios you don't need shell commands.

  Thank you

  Johan

  Hey there,

  Check these stars-

  http://msdn.Microsoft.com/en-us/library/Windows/hardware/ff545500 (v = vs. 85) .aspx

  http://TechNet.Microsoft.com/en-us/library/cc749064 (v = ws.10) .aspx

  http://uefidk.Intel.com/sites/default/files/SF11_EFIS003_100.PDF

  http://www.sysadminshare.com/2012/01/EFI-shell-commands.html

• I have to add new contacts in the database. Should what stage of treatment I add?

  I have to add new contacts to the database. Should what stage of treatment I add?

  Hello

  Please use "Save to the Contact Table" stage of treatment.

  Thank you

  edynamic Experts Eloqua

• The BIOS Setup screen

  On my desk a6763w, my bias shows my HD to be the No. 3 Starter upward and my dvd to be no. 2. 1 is empty, n ° 4 is empty. My first start should not be my HD? On the motherboard it is pluged in Sata slot No 1 and no 2 dvd. 3 and 4 are empty. My bios version is a bit confusing, I'm 5.29!

  Hi PapaDan8,

  I saw your post and I will be happy to explain. The number in the BIOS which shows the unit is not important today. The IDE using older had to but as long as the boot sequence is set up in the correct order no matter what the figures show.

  You have a questions or problems with the PC? If so, let me know what is your operating system and your product number.

  Find your product on a desktop computer number:

  http://support.HP.com/us-en/document/bph07555

  Find your operating system:

  http://Windows.Microsoft.com/en-CA/Windows/which-operating-system

  Thank you

• Acer Aspire V3 - 772G - BIOS setup utility menus have disappeared

  Acer Aspire V3 - 772G - BIOS setup utility menus have disappeared

  I have install this laptop brand new, pre-installed with Windows 8.1 for my sister-in-law who bought it.  The installation went well BUT the 16 GB USB device I bought such as advised by the literature of Acer to store the recovery partition was not large enough, 14.4 GB physical capacity.  Acer the book says to use a 16 GB or more, so I did.  I naively thought that a USB key which has been marked 16 GB would be appropriate.  Not the case.  I had to buy a bigger but am still waiting for delivery.

  So I decided to any HARD drive to save the work I had done, but found only the Acronis Backup and Recovery DVD would not start the image.  I went into the utility configuration and adjusted the start parameters to inherited and modified device priority.  Acronis wouldn't so I did not continue.  I went back into the configuration utility, use F9 to restore the default value and to my astonishment that the DUAL boot option was now gone and Windows startup option was also gone.

  This means that £800 this laptop is now unusable.  The installer standalone reconfigured without warning.  Nowhere is there at - it advice or advice do not use the Setup utility when it erases the features that cannot be recovered by using F9 to restore the default configuration.  If this isn't a serious design flaw, I don't know what is.

  I am deeply worried because the idea of a BIOS setup utility behave in this way seems so unlikely that I wonder if anyone will believe me.  How are the Setup utility has been designed to self-harm like this?

  Your suggested action works!  Thank you very much.  You saved my life.

  loungehake

• Pavilion g6 2310sd: enter the bios setup

  After 3 times wrong password to get into the bios, I got the 68794387 code. You have a code to enter in the bios?

  Hello

  Enter 77692909

  Kind regards

  DP - K

• How to enter the BIOS setup firmly

  8.1 - Whenstarting Windows that I'm trying to access the BIOS Setup. I push F2 repeatedlyeven after seizure-Toshiba screen is displayed. Almost always, I get on Windows system, only very few times I get to a tenth of a second at the left bottom of the screen saying line something like "to enter the BIOS. But then it is already too late to grab something. Is there a howto method course enter the savelie BIOS Setup? I have a Toshiba-computer laptop-P500-PSPGSE.
  Thank you very much in advance youvery.
  hansm

  F12 after start-up for multiboot-selection-Menu does not work either.