I have error GETan say for this device does not properly because windows cannot load the drivers required for this device (code 31) to 6to4 adapt #2 and #7 wher can I get these re install

Similar Questions

• Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

  Original title: WAN miniport driver

  A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I use windows 8 in my sony vaio
  MODEL - SVE15123CNW

  Hi Praveen,

  Perform the steps suggested by Nirmal S from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

  Answer please if you have any questions.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello

  Have you tried to update the drivers as suggested by Basith M?
  
  Method 1:
  You can run the fix provided in the link and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems

  
  Method 2:
  You can also try the procedure described in the link to troubleshoot driver issues.
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  
  See also the proposal contained in the link and check.
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Microsft #8 ISATAP adapter... This device does not work because windows cannot load the drivers for this device Code 31... ??? Can anyone help I just use computers don't understand them...

  I tried to update the drivers but it says that I have installed the last...

  See this:
   
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
   http://support.Microsoft.com/kb/932520
   
  You can ignore this error message. This error message does not indicate a problem with the adapter. The adapter will continue to function correctly.
   
  You can uninstall and windows should reinstall on reboot, but you can install it yourself.
  How uninstall/reinstall Isatap
   http://www.ehow.com/how_7567513_reinstall-ISATAP.html
   
  If you cannot connect to your network, you have another problem.
  Try to manually update your (wireless) network adapter. Go to the support site for your computer manufacturer and download the latest driver:
   
  How to upgrade Windows Vista drivers
   http://pcsupport.about.com/od/fixtheproblem/HT/updatedrvvista.htm

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) my video card does not work why?

  can u help me quickly?

  Hello

  -For how long have you had the problem?
  -Did you change your computer, after which the question began?

  I suggest that you uninstall and reinstall the drivers for video card and check if that helps.

  Uninstall or reinstall a device

  Note: Not applicable for Windows Vista also.

• Microsoft ISOTAP #14 adapter this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  can someone help me please, I need to fix this as its making the computer

  Hello

  Control Panel - devices - right click on - UNINSTALL - REBOOT Manager

  Nothing else to do, Windows will do the rest. And you can ignore the error if you wish and on some
  computers, it will always be there but no problem to be expected.

  On a Windows Vista-based computer or on a computer, Windows Server 2008, the card Microsoft ISATAP
  appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520

  Hardware devices not detected or does not
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Mirosoft 6to4 adapt isin can't work because windows cannot load the drivers required for this device (Code 31)

  I replaced a heatsink and fan in a laptop of friends.  The laptop works fine now.  In Device Manager, however, I'm getting a code 31 for the Microsoft 6to4 adapter.  Is it because this person uses several networks? Is it because I'm connected to my home network?  Or I did something wrong during the reassembly? Someone of you know this?

  If you experience any problems you can ignore it.

  See these:

  Microsoft 6To4 card issues
  http://www.ehow.com/way_5602460_microsoft-6to4-adapter-problems.html

  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• Error: This device does not work properly because Windows cannot load the...

  I get this error message "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) "via a wired connection. And that's the Microsoft 6to4 adapt #7 and the same card but the #4 one.  Are these drivers or another file that I could use DL?

  Hi JasonBedgood,

  1. Once you get the error message?
  2. did you of recent changes on the computer?

  This error occurs if the required driver is not installed or the driver is damaged.

  I suggest that you update the driver for the device and check.

  How can I update the driver for network card on the computer

  1. click on Start, click Control Panel, and then double-click System.
  2. click the tab hardware , and then click Device Manager.
  NOTE: If you are prompted for an administrator password or for confirmation, type the password, or click continue.
  3. click on network adapters to expand.
  4. under network adapters, double-click the entry for Microsoft 6to4and then click driver .
  5. click on Update driver software.
  6. follow the Wizard update software driver to update the driver for NICs .

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the device driver update did not help then check the link below for one of the thread with the question and try the steps mentioned by Lionel Chen on January 9, 2008
  http://social.technet.Microsoft.com/forums/en-us/itprovistahardware/thread/3a503cdb-e61c-44BC-97c4-0b38b0e5f929/

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows cannot load the drivers for the network device, Code 31

  A few days ago, my computer was working very slow... I turned off twice and he turned his back.  The letters on the screen were enormous when windows restarts.  I turned off and did a diagnostic system before windows starts and everything was fine.  The computer is restarted my network cards were missing.  I get the error: this device does not work properly because Windows cannot load the drivers for this device. (CODE 31).  (Module Aetheros 802.11 a/b/g/n dualband wireless network and Realtek PCIe GBE Family Controller).

  I have downloaded device drivers (windows could not find them on my system) using a laptop and copied computer on a disc.  I tried to install and I got an error message indicating that windows has failed.  I did a system restore to a point a few days before I started having problems.  Windows cannot successfully go back to the restore point.  I spoke with a technology computer and HP tech.  HP technology seems to think that windows is damaged and I need to remove and reinstall it on my computer.  I spoke with computer technology in my area, and he seems to think that my hard drive has failed, however I can still run photoshop and backup my system.

  Does anyone have any ideas before I m computer local tech.  3 year warranty just expired February 1, 2011.  Don't you know.

  Hi TeresaPacy,

  1. don't try to install new software or hardware on your computer recently?

  You try to run a SFC scan to check the corrupted system files.

  You can read the following article to launch the SFC scan:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Regarding errors of network adapter, you can consult this article:

  http://TechNet.Microsoft.com/en-us/library/cc725584 (WS.10) .aspx

• In my report of diagnostic systems that it establishes that there is an error indicating the symptom is "device is not working properly." Windows cannot load the required device drivers. "I don't know what to do.

  Windows cannot load the required device drivers.  It shows the details like Microsoft ISATAP adapter reports "tv_ConfigMgrErr31.  This device won't be available until the problem is resolved.  The Plug-and-Play ID is 17.  What this mean and how can I make the correction of this error and operate?

  Hello

  Control Panel - devices - right click on - UNINSTALL - REBOOT Manager

  Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you wish
  and on some computers, it will always be there but don't cause any trouble.

  On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
  ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
  error message
  http://support.Microsoft.com/kb/932520

  Y at - it no devices work not?

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.