I have no sound on the computer after the installation of Windows XP.

Similar Questions

• Blue screen during the installation of windows 7

  Hi guys, this is my first question. I have a problem during the installation of windows. A blue screen saying is displayed "STOP: c000021a {fatal system error}.

  The initial session process or the process of the finished system unexpectedly with a status of 0 x 00000000 (0 xC0000001 0x001003f0).

  The system stopped"I can't do anything else than the computer shutdown. Please help me

  Could you provide your system specifications?

  Are the upgrade from a previous version of Windows or to do a clean installation?

  This is usually caused by hardware or software that is not compatible with Windows 7. If you have this problem, follow these steps:

  Uninstall all antivirus software, and then restart your computer. Don't forget to enable antivirus software after you install Windows.

  If the installation fails again, it may be a hardware incompatibility problem. Go to the Windows 7 Upgrade Advisor on the Microsoft website to see if your computer can run Windows 7.

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  If the computer still stops responding during Setup, contact your manufacturer computer or your retailer.

• Get a black screen during the Installation of Windows 8

  Original title: BLACK SCREEN

  OK, I tried 5 times to install windows 8 by using the downloaded Update widows Pro

  I've updated the BIOS and other drivers and the only issue is to use the upgrade wizard is UEFI is not compatiable that shouldn't be a problem anyway
  So here's the BLACK SCREEN problem, I get all along to install past loan, after adjustment of the apparatus, after preparation, all the way to the end and then it gives just black screen until I power it turns off or reset and says windows 8 could not restore windows I get no error code or any hint of why there not everyone had an idea Yes stay with windows 7 is an excellent option, but I would try and brand and make informed decisions.
  I have internet search and it seems to be a common problem for many different reasons - ideas - Ive tried more things ive read without success. Help please

  Hello Kiwivic,

  Thank you for the question!

  I'm sorry to know that have problems you with the Installation of Windows 8. As I understand it, you get a black screen during the Installation of Windows 8.

  I need to ask you some questions to help you best.

  1. What is the brand and model of the computer?

  2 are the external devices connected to the computer?

  Method 1: disconnect any external devices (except keyboard and mouse) and then install Windows 8 and check.

  Method 2: Select the edge device devices in device/integrated graphic of BIOS (Basic Input output device) and check.

  Warning: Be careful when you change the BIOS settings. The BIOS interface is designed for advanced users, and it is possible to change a setting that can prevent your computer from starting properly. BIOS update should be made only if necessary (to solve a compatibility problem, for example). It can be a complicated process, and if an error occurs, your computer could be rendered inoperative. Be sure to observe the instructions of the manufacturer.

  Reference link provided below for more information:

  BIOS: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/BIOS-frequently-asked-questions

  Meet us if you encounter any problems with the black screen or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• I have no sound on my computer, no icon in my taskbar to the sound, in my manager to design, I mark on other currencies and multimedia Audio control points.

  I have a Microsoft Windows XP desktop.
  My icon on my taskbar is missing for the sound and volume.
  I have NO sound on my computer except when it starts.
  I no. MY Computer Icon when I go to start.

  Go over each step in the following link, note that there are several tabs in the page:
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

• I have no sound on my computer (Windows XP). I installed audio driver with no result. What to do next?

  No sound

  I have no sound on my computer (Windows XP). I installed audio driver with no result. What to do next?

  Hi f. Mac,.

  Follow the steps in the article.

  How to troubleshoot sound problems in Windows XP

  No sound in Windows

• I HAVE NO SOUND ON MY COMPUTER WITH WINDOWS XP PRO

  My computer crashed and has upgraded windows xp to XP pro and now I have no sound

  The following links may be worth a visit:

  (307918) how to troubleshoot sound problems in Windows XP
  http://support.Microsoft.com/kb/307918/en-GB

  Diagnose and automatically repair audio playback problems
  http://support.Microsoft.com/mats/AudioPlayback/

  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
  (Win XP / Vista / 7)

• have no sound on my computer

  not sure if this is where I ask, but I have no sound on my computer and my new speakers do not work

  Hello

  Yes, you asked your query in the category.

  · When you say no sound, are there no system sound or no sound of any particular application?

  · You receive an error message or error code when you try to use your new speakers?

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed?

  · What is the number and the model of the computer?

  Give the above information to us troubleshoot-performed the best to help. In the meantime you can see the article below no sound in Windows: http://windows.microsoft.com/en-US/windows/help/no-sound-in-windows :

• I have no sound in my computer, but I can see my sound card but still no sound.plzzzzzz help?

  I have no sound in my computer, but I can see my sound card but still no sound.plzzzzzz help?

  See if the following tutorials will help:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
  He
  consists of 3 parts:
  1 check the hardware
  2. use a troubleshooting tool
  3.
  Updated drivers

  Diagnose and
  automatically fix audio problems
  http://support.Microsoft.com/mats/NO_SOUND/en-us

  He has a difficulty he asked along with other
  Related topics.
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  Audio Troubleshooting
  Problems
  http://support.Microsoft.com/GP/troubleshoot_audio_windows

• I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

  I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

  The primary partition has the following folders (including hidden & system)

  The recovery partition has the following (including the language files more)

  Someone at - it ideas why my laptop does not work?

  Thank you

  Greg

  Hello

  You press F11 on startup with a HP Compaq to start the recovery process.

  For problems with the recovery process, you will need to contact HP.

  BIOS problems:

  There are messages for the HP Forums for posters with similar errors:

  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

  All the answers it point to a drive about to fail

  See you soon.

• Hello, we are runing Adobe Acrobat Professional 7.0 and it suddenly stopped working for one of our computer after one month after the installation of windows 10. Someone had the same problem and it is resolved?

  Hello, we are runing Adobe Acrobat Professional 7.0 and it suddenly stopped working for one of our computer after one month after the installation of windows 10. Someone had the same problem and it is resolved?

  Not compatible with the system after XP. Upgrade.

• Computer guard reboot during the installation of windows 7

  Hello world

  I just bought a desktop computer and put up my car, it consists of a z - 87 asus mother board I just bought with 32 GB Patriot memory, processor intel i7 and when I install windows and get to the point where it asks me to put in the name of the computer, and as soon as I hit next will be the remote computer.

  at first I thought it was the hard drive, so I bought a new 256 SSD disk scan and its still doing the same thing.

  What should I do, all the parts in the PC are brand new.

  Thank you

  Moved from the center of Community Participation.

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  Reduce the amount of RAM installed on a single key and proceed with the installation of Windows 7. If the installation is successful, you can reinstall after the extra RAM.

  Also, if you have more than one attached internal storage device, disconnect all but the target device where Windows 7 is installed.

• After the installation of Windows 'important' 3 updates my screensaver started does not. I get a message that says "ScreenSaver:Photo screensaver.scr - unable to locate component".

  Original title: screen saver does not start because MSVCR100.dll was not found

  After the installation of Windows 'important' 3 updates my screensaver started does not. I get a message that says:

  ScreenSaver: Photo screensaver.scr - unable to locate component.

  This application has failed to start because MSVCR100.dll was not found. Reinstalling the application may fix this problem.

  The screen saver starts after you close the error message. I've never had a problem with my screen saver up to that after I downloaded updates. I don't know how to reinstall the application. I tried Windows Fix - It Solutions, but it does not work. He repeated to me that it was a mistake.

  Help, please. Thank you.

  Hello

  It didn't reinstall the ATL update, it reinstalled 2005 Redistributable. So now, I have 2005 and 2010 x 86 both. And it says that two dates installiation are two days after I installed the 2010. I know 2005 and the update was uninstalled, because I checked after restart the computer and before you install the 2010 version. Very curious.

  But my Screensaver works and access to the camera seemed to work after uninstalling / reinstalling the software. So, good. Thank you.

• Windows 8 OEM samsung original is disabled after the installation of windows updates.

  I have the original windows 8(Samsung Laptop) confirmed by Samsung as the original windows. Have this laptop for about 2 years now and have reset my windows again. But this time after the installation of windows updates, my windows are disabled and the watermark comes and it is said to activate windows. Samsung said support windows is authentic and check with Microsoft. But Microsoft has no support for 24 hours and support is not live at this time. Can someone help me with this problem. Please, I beg you. And I tried to put the key in the firmware to activate, but nothing helped. And the OEM key is invalid for activation at all.and add I activated my windows by phone before the update using the technique of slui 4... and after it started to update. And now reactivate cant using this key method.and calling OEM is not valid anywhere.

  Hello

   
   
  Please contact Microsoft Community.
   
  We regret sincerely all the inconvenience caused to you.
   
  I suggest you try the phone activation this time and see if it helps.
   
  a. at the start screen, drag from the right side, or hover your mouse on the top right of the screen to display the menu of charms.
  b. tap or click the charm of parameters.
  c. press or click on change PC settings.
  d. If your PC is not activated, computer settings provide instructions that are customized to your activation error. If telephone support can provide assistance for your mistake, tap or click the appropriate link, which may resemble one of the following conditions:
  > Activate

  > Activate by phone

  I suggest you refer to the following article for more information.

  http://Windows.Microsoft.com/en-us/Windows-8/activation-errors
   

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  Kind regards
  Anusha

• Old dualboot options still available after the installation of Windows 8 Pro on a desktop Pc which had XP and Windows 8 prewiev version on that front.

  Old dualboot options still available after the installation of Windows 8 Pro on desktop in XP, but now triple options. Windows 8 Pro (volume 1), Windows 8, old windows installation.  Anyone who knows how to get rid of the last two options?  The good thing is now that I don't have to put a password everytime I turn on the computer.

  Press the Windows key + X and then click System

  

  Click on advanced system settings

  Click the Advanced tab

  Under Startup and recovery, click settings

  

  Select Windows 8 and uncheck the box "time to display list of operating systems.

• Hello I have a problem with the installation of Adobe Photoshop elements 13!

  Hello I have a problem with the installation of Adobe Photoshop!

  Le instalationsprogramm va on I can also enter the key but after 2% left the program.

  Can you help me?

  Run the vacuum cleaner by the use of the Adobe Creative Cloud cleaning tool to solve installation problems

  you restart the computer

  and run the Setup again.

  If it fails again during installation, troubleshooting install using newspapers | Elements

• Have a problem with the installation of CF9

  Hello

  I try to install CF9 on my computer, but I have a problem, once the installation is complete and he gets to the part administrator and Migration (the part where it opens a browser). I enter the admin password, and then click ok, then he's going to the page that says that the server is configured. There is a note that says that it can take a few minutes, but after a wait of 10-15, I get a time-out error that says that demand is greater than the permitted time limit. I don't know what to do at this point. I tried reinstalling and changing installation options, but nothing works.

  On a note separated, once the installation is complete, I get a Jrun4 process in Windows Task Manager and it completely my computers memory hogs. After a few minutes, it will use about 500 MB of memory and the computer is unusable because of how long it takes to respond to each click.

  Help, please!

  Here are the stats from my computer:

  (Filled all the requirements of system)

  Windows Vista Edition Home Premium

  AMD Athlon (TM) 64 X 2 Dual - Core TK-57 1.9 GHz processor

  959 MB OF RAM

  32 - bit operating system

  My default browser is Google Chrome and it's what he uses when it goes through this problem. I tried manually run the link administrator with IE and firefox and I get the same problems.

  My computer is a HP Compaq Presario F700 laptop and its about 2 years while working well, maybe it's just not up to running CF9?

  Thanks for any help,

  Alex

  I've never used this cfstart.bat file to start CF.  The process to install a Windows Service must have been created: use it.  I don't know if it makes a difference, but through a shell you do in CF cfstart.bat may not be a perfect way of doing things.

  The CF error you get just means that CF is pulling the plug on your request because it takes so long.  I think that, by default, there is a 60 sec timeout.  I've never seen CFAdmin take 60-sec to boot.  This setting is usually configured via CFAdmin and not sure where to turn off if this same setting prevents a bet in CFAdmin.  I'll have a look later... time for me to jump on a bandwagon.

  Maybe put your Xmx set back up to at least 256 MB.  To save a little bit more RAM, you could probably reduce your - XX: MaxPermSize to the low a little too (maybe up to 64 MB?  Not sure about that).

  Your PC seems to be quite tight on resources, if you need to do this kind of thing, btw.  I note that you use only 1 GB of RAM on a Vista machine.  EEEK.  I wouldn't anything less than 2 GB (and would prefer 4 GB while she performance).  Your question may that Windows is having to share a RAM disk too, which will slow down everything until analysis.  Which seems to be what you feel.  Windows itself needs... what... about 400 MB to run these days, before you start trying to assign any what RAM in other applications.  1 GB is not enough.

  --

  Adam